Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “laser shock”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Impact of mid- Z gas fill on dynamics and performance of shock-driven implosions at the OMEGA laser

Shock-driven implosions with 100% deuterium (D 2 ) gas fill compared to implosions with 50:50 nitrogen-deuterium (N 2 ⁢D 2 ) gas fill have been performed at the OMEGA laser facility to test the impact of the added mid-Ζ fill gas on implosion performance. Ion temperature (Τ ion ) as inferred from the width of measured DD-neutron spectra is seen to be 34%±6% higher for the N 2⁢ D 2 implosions than for the D 2 -only case, while the DD-neutron yield from the D 2 -only implosion is 7.2±0.5 times higher than from the N 2⁢ D 2 gas fill. The T ion enhancement for N 2 ⁢D 2 is observed in spite of the higher Z, which might be expected to lead to higher radiative loss, and higher shock strength for the D 2 -only versus N 2 ⁢D 2 implosions due to lower mass, and is understood in terms of increased shock heating of N compared to D, heat transfer from N to D prior to burn, and limited amount of ion-electron-equilibration-mediated additional radiative loss due to the added higher-Z material. Further, this picture is supported by interspecies equilibration timescales for these implosions, constrained by experimental observables. The one-dimensional (1D) kinetic Vlasov-Fokker-Planck code ifp and the radiation hydrodynamic simulation codes hyades (1D) and xrage [1D, two-dimensional (2D)] are brought to bear to understand the observed yield ratio. Comparing measurements and simulations, the yield loss in the N 2 ⁢D 2 implosions relative to the pure D 2 -fill implosion is determined to result from the reduced amount of D 2 in the fill (fourfold effect on yield) combined with a lower fraction of the D 2 fuel being hot enough to burn in the N 2 ⁢D 2 case. The experimental yield and T ion ratio observations are relatively well matched by the kinetic simulations, which suggest interspecies diffusion is responsible for the lower fraction of hot D 2 in the N 2 ⁢D 2 relative to the D 2 -only case. The simulated absolute yields are higher than measured; a comparison of 1D versus 2D XRAGE simulations suggest that this can be explained by dimensional effects. The hydrodynamic simulations suggest that radiative losses primarily impact the implosion edges, with ion-electron equilibration times being too long in the implosion cores. The observations of increased T ion and limited additional yield loss (on top of the fourfold expected from the difference in D content) for the N 2 ⁢D 2 versus D 2 -only fill suggest it is feasible to develop the platform for studying CNO-cycle-relevant nuclear reactions in a plasma environment.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

High precision control of laser energy for laser–matter interaction studies

Precise, highly reproducible control of the laser energy is required for high confidence laser–matter interaction research such as in dynamic compression science and high energy density physics. The energy must be adjustable without affecting the pulse shape (time varying intensity) or beam smoothness. We have developed a convenient two-stage energy tuning method for a nominal 100 J, 351 nm (UV) laser. The energy is adjusted in 10 J (10%) increments by operating the laser at full energy and inserting a beam splitter in the laser output. As the splitter is located after the final frequency tripling optics, the UV pulse shape is unchanged. The energy is varied by substituting a splitter of different reflectivity. For finer 3 J (3%) increments, the infrared pulse is attenuated inside the laser before the final amplifier. This requires modest tuning to preserve the pulse shape. The demonstrated variation in shot-to-shot reproducibility is less than +/–2.5 J (5% of the full energy), irrespective of the laser output energy. These approaches can be adapted to most ~100 J class lasers. We describe these techniques and show two examples where they have elucidated the underlying physics in laser shock compression experiments. One used only the beam splitters to establish the pressure for melting in iron. The other combined both techniques to finely increment the peak stress (~2 GPa steps) in germanium to precisely determine the onset and completion of melting—including the melting kinetics. Furthermore, these unambiguous results would not be possible without the developments described here.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Peening Techniques for Surface Modification: Processes, Properties, and Applications

Surface modification methods have been applied to metals and alloys to change the surface integrity, obtain superior mechanical properties, and improve service life irrespective of the field of application. In this review paper, current state-of-the-art of peening techniques are demonstrated. More specifically, classical and advanced shot peening (SP), ultrasonic impact peening (UIP), and laser shock peening (LSP) have been discussed. The effect of these techniques on mechanical properties, such as hardness, wear resistance, fatigue life, surface roughness, and corrosion resistance of various metals and alloys, are discussed. This study also reports the comparisons, advantages, challenges, and potential applications of these processes.

microstructure↗
DOE OSTI2021

Density evolution after shock release from laser-driven polystyrene (CH) targets in inertial confinement fusion

The evolution of the plasma density in the rarefaction wave formed after a laser-driven shock is released from a CH foil was measured using optical interferometry. Here, it was found that the plasma density profile is very sensitive to the conditions at the back surface of the foil before the shock release. Dedicated experiments demonstrated that radiation preheat by coronal x-rays caused early expansion of the back surface and faster expansion of the rarefaction wave. Radiation-hydrodynamics simulations with accurate modeling of radiation preheat from the plasma corona are in good agreement with the experimental results. The early expansion of material interfaces due to coronal x-ray preheat must be evaluated in designing and interpreting laser-driven inertial confinement fusion experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

First-principles simulation of a shocked H-He mixture along the principal Hugoniot

Recent laser-shock experiments on an H–He mixture containing 11% helium (atomic fraction) have suggested the presence of an immiscibility region inside Jupiter. Reflectivity measurements were used as the primary diagnostic of H–He demixing, with discontinuities in the optical reflectivity proposed as a signature of phase separation under conditions relevant to Jupiter's interior. Here, we investigate shock-compressed H–He using ab initio molecular dynamics simulations with optical properties evaluated within the Kubo–Greenwood formalism. The equation of state and ionic configurations were obtained using the thermal Tr 2 SCANL meta-GGA exchange–correlation (XC) functional, while optical properties were computed using the recently developed RS-KDT0 range-separated thermal hybrid XC, which provides state-of-the-art accuracy for band-gap predictions in the warm dense matter regime. The calculated reflectivity shows overall good agreement with experimental measurements; however, no discontinuity is observed at elevated temperatures. Moreover, the reflectivity predictions for the mixed system are consistent with the experimental measurements in the temperature range where the mixture is inferred to be demixed. Furthermore, these results suggest that reflectivity alone may not provide a unique or sensitive diagnostic of H–He demixing at low helium concentrations under these conditions.

Density functional calculations↗
DOE OSTI2022

Measurement of shock roughness due to phase plate speckle imprinting relevant for x-ray diffraction experiments on 3rd and 4th generation light sources

Laser-shock compression experiments at 3rd and 4th generation light sources generally employ phase plates, which are inserted into the beamline to achieve a repeatable intensity distribution at the focal plane. Here, the laser intensity profile is characterized by a high-contrast, high-frequency laser speckle. Without sufficient smoothing, these laser non-uniformities can translate to a significant pressure distribution within the sample layer and can affect data interpretation in x-ray diffraction experiments. Here, we use a combination of one- and two-dimensional velocity interferometry to directly measure the extent to which spatial frequencies within the laser focal spot intensity pattern are smoothed out during propagation within the laser plasma and a polyimide ablator. We find that the use of thicker polyimide layers results in spatially smoother shock fronts, with the greatest degree of smoothing associated with the highest spatial frequencies. Focal spots with the smallest initial speckle separation produce the most rapid smoothing. Laser systems that employ smoothing by spectral dispersion techniques to rapidly modulate the focal plane intensity distribution are shown to be the most effective ones in producing a spatially smooth shock front. We show that a simple transport model combined with the known polyimide Hugoniot adequately describes the extent of shock smoothness as a function of polyimide thickness. Finally, our results provide a description of spatial structure smoothing across a shock front, which can be used to design targets on x-ray free electron laser facilities.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Quantitative measurements of density in shock-compressed silver up to 330 GPa using x-ray diffraction

This work presents a structural study of shock-compressed states in Ag to 331 GPa, accessed via laser shock compression. Structures of the resulting crystalline phases and the average atomic distribution of the liquid state are determined using in situ x-ray diffraction. We employ structure factor analysis, adapted for a non-monochromatic x-ray source, to determine the density of the liquid phase from analysis of x-ray diffraction data for the first time in shock compressed Ag. We also present a detailed analysis of the crystalline phases, which shows good agreement with the phase boundaries reported in previous experimental and theoretical works. We utilize the whole powder pattern fitting approach implemented in the MAUD package to constrain stacking faults in the face centered cubic structure. We observe the ambient fcc structure up to a stress of 146 GPa before a transition to a body-centered cubic structure and liquid phase at 179 GPa, with full melting above 212 GPa.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

A field programmable gate array-based timing and control system for the dynamic compression sector

A field programmable gate array (FPGA)-based timing and trigger control system has been developed for the Dynamic Compression Sector (DCS) user facility located at the Advanced Photon Source (APS) at Argonne National Laboratory. The DCS is a first-of-its-kind capability dedicated to dynamic compression science. All components of the DCS laser shock station—x-ray choppers, single-shot shutter, internal laser triggers, and shot diagnostics—must be synchronized with respect to the arrival of x rays in the hutch. An FPGA synchronized to the APS storage ring radio frequency clock (352 MHz) generates trigger signals for each stage of the laser and x-ray shutter system with low jitter. The developed FPGA-based control system was the first system used to control the laser and the shutter system since its commissioning, and it has been developing since then to improve the timing jitter. The system is composed of a Zynq FPGA, a debug card, line drivers, and a power supply. The delay and offsets of the trigger signals can be adjusted by using a user-friendly graphical user interface with high precision. Here, the details of the system architecture, timing requirements, firmware, and software implementation along with the performance evaluation are presented in this paper. The system offers low timing jitter (15.5 ps rms) with respect to the APS 352 MHz clock, suitable for the 100 ps (FWHM) x-ray bunch duration at the APS.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Shock compression of silver to 300 GPa: Wave profile measurements and melting transition

Recent in-situ x-ray diffraction (XRD) measurements on laser-shock compressed Ag foils demonstrated a face-centered-cubic to body-centered-cubic transformation at ~150 GPa and melting between 172 and 197 GPa [Phys. Rev. Lett. 124, 235701 (2020)]. As a complement to the XRD work, we conducted plate impact experiments to obtain shock velocity and wave profile measurements on thicker Ag samples shock-compressed to peak stresses between 30 and 300 GPa. The shock velocity–particle velocity results were fitted very well by a linear relation over the entire stress range, providing an accurate determination of the Ag Hugoniot (locus of the stress-volume states achieved under shock compression). For peak stresses below 187 GPa and above 210 GPa—corresponding to the solid and liquid phases, respectively—the wave profiles show clean single waves. No wave profile features related to the fcc-bcc transformation at ~150 GPa were observed, implying minimal volume change for the transformation. For stresses between 187 and 210 GPa, an initial jump was followed by a time-dependent increase in the particle velocity (20–80 ns risetime) to the peak state—corresponding to the solid-liquid mixed phase response. Unlike the solid and liquid response, the mixed-phase response cannot be readily analyzed analytically. Instead, numerical simulations incorporating an accurate multiphase equation of state for Ag—not currently available—are required to analyze the wave profiles measured at 187–210 GPa stresses. Furthermore, the present work shows the potential for using wave profile measurements to examine the melting transition under shock compression.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2011

Laser Peening Effects on Friction Stir Welding

Friction Stir Welding (FSW) is a welding technique that uses frictional heating combined with forging pressure to produce high strength bonds. It is attractive for aerospace applications. Although residual stresses in FSW are generally lower when compared to conventional fusion welds, recent work has shown that significant tensile residual stresses can be present in the weld after fabrication. Therefore, laser shock peening was investigated as a means of moderating the tensile residual stresses produced during welding. This slide presentation reviews the effect of Laser Peening on the weld, in tensile strength, strain, surface roughness, microhardness, surface wear/friction, and fatigue crack growth rates. The study concluded that the laser peening process can result in considerable improvement to crack initiaion, propagation and mechanical properties in FSW.

Hatamleh, Omar↗
NASA NTRS1987

Shock structure measured in a transonic fan using laser anemometry

Shock structure measurements acquired in a low aspect ratio transonic fan rotor are presented and analyzed. The rotor aspect ratio is 1.56 and the design tip relative Mach number is 1.38. The rotor flowfield was surveyed at near maximum efficiency and near stall operating conditions. Intra-blade velocity measurements acquired with a laser fringe anemometer on blade-to-blade planes in the supersonic region from 10 to 60 percent span are presented. The three-dimensional shock surface determined from the velocity measurments is used to determine the shock surface normal Mach number in order to properly calculate the ideal shock jump conditions. The ideal jump conditions are calculated based upon the Mach numbers measured on a surface of revolution and based upon the normal Mach number to indicate the importance of accounting for shock three dimensionality in turbomachinery design. Comparison of the shock locations with those predicted by a 3-D Euler code showed very good agreement and indicated the usefulness of integrating computational and experimental work to enhance the understanding of the flow physics occurring in transonic turbomachinery passages.

Wood, Jerry R.↗
DOE OSTI2024

Effects of drive pulse shape on graded metal pushered single shell capsule implosions on the National Ignition Facility

Graded metal pushered single shells (PSS) are a viable alternative to low-Z capsules (Z is the atomic number) for indirect drive inertial confinement fusion implosions due to enhanced core tamping and radiation trapping, but they can be compromised by the pusher mixing with the fuel. We compare 2-shock and 3-shock laser pulses for Be/Cr PSS capsules filled with deuterium–tritium gas fuel at 6 mg/cc density. 1D radiation-hydrodynamic simulations predict higher core compression and, hence, ∼2× higher fusion yield for the 3-shock drive than for 2-shock. Nevertheless, we observe similar core ion temperatures and fusion yields for both drives. The implosion burn duration is 25% shorter and the core volume is ∼2.5× smaller for the 3-shock drive than for 2-shock, consistent with a higher compression. 1D LASNEX mix simulations using a buoyancy-drag model matching the measured yields also agree with the observed core sizes and burn durations and suggest ∼40% and ∼70% yield degradations for 2-shock and 3-shock drives due to hydrodynamic instabilities and atomic mix at the pusher–fuel interface. At the same time, 2D HYDRA simulations show that mid-mode (2–250) instability degradations are negligible for the 2-shock implosion (9%) and significant (45%) for 3-shock. Subtracting these from the 1D mix simulations, we infer similar degradations from high-mode instabilities and atomic mix for both drives. Due to its robustness to mid-mode instabilities, future pusher–gas mix studies will use the 2-shock drive.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Computational Design of a Simple Flyer Plate Launcher

The response of materials to shock loading is important to understand for a variety of applications. When shock physics emerged during and after WWII, direct explosive loading or explosively driven plate impact was the primary tool for these studies. Subsequent decades have seen the widespread use of large caliber guns for plate impact studies, laser-shock facilities and pulsed power facilities. INL currently lacks a gun suitable for plate impact or explosives casting and machining facilities; however, it does possess explosives use and handling capabilities. An option for performing plate impact experiments was needed, therefore continuum scale models were utilized to explore a few simple donor-acceptor explosive plane wave lens designs, one of which could be hand packed with plastic explosives to launch flyer plates. 2D simulations were performed to study different geometries in an effort to minimize the difference in shock arrival across the central portion of a small copper flyer plate. A shock wave arrival time difference under 50 ns across 50 percent of the center of the flyer was achieved with a few designs. This work summarizes the computational models and results.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Diamond under extremes

Diamond is, by virtue of the covalent bonding between atoms and the very strong carbon to carbon bonds, the hardest natural material. It has been a fascinating material since its discovery, first as a decorative gem and more recently, for its numerous industrial uses because of its extreme hardness, elastic modulus, and optical transparency. In recent years, it has become a preferred ablator for laser shock experiments, and this has led to its choice as the capsule material for fusion experiments at the National Ignition Facility. Further, this review covers both experimental and computational (including machine learning) advancements in research on diamond subjected extreme conditions of temperature and pressure. The synergy between shock and ramp loading experiments and atomic level simulations is proving to be powerful in advancing our understanding of diamond under extremes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shock melting and the hcp-bcc phase boundary of Mg under dynamic loading

The high-temperature and high-pressure response of magnesium has been investigated through shock-release experiments performed up to shock melting. The longitudinal and bulk sound speeds of Mg are reported along the Hugoniot from 25 to 56 GPa and used to determine the elastic properties and Grüneisen parameter. The hexagonal close-packed (hcp)–body-centered cubic (bcc) phase transition is marked by a reduction in the determined shear wave speed. Thermal softening is observed to begin between 40 and 44 GPa, with incipient melt at 55.5 GPa, in close agreement with previous diffraction measurements under laser shock loading. Examination of the release profiles showed that two different responses were observed, depending on the peak stress. When plotted in a stress-energy phase diagram, the two responses are observed to form separate lines that intersect the static hcp-bcc phase transition and incipient melt. The results indicate that the hcp-bcc transition occurs on the Hugoniot at 28.4 GPa and place the hcp-bcc-liquid triple point ~20 GPa. In conclusion, a multiphase equation of state is developed which places the melt boundary below the previously reported static measurements.

36 MATERIALS SCIENCE↗
NASA NTRS1995

High temperature kinetic study of the reactions H + O2 = OH + O and O + H2 = OH + H in H2/O2 system by shock tube-laser absorption spectroscopy

The reactions: (1) H + O2 = OH + O; and (2) O + H2 = OH + H are the most important elementary reactions in gas phase combustion. They are the main chain-branching reaction in the oxidation of H2 and hydrocarbon fuels. In this study, rate coefficients of the reactions and have been measured over a wide range of composition, pressure, density and temperature behind the reflected shock waves. The experiments were performed using the shock tube - laser absorption spectroscopic technique to monitor OH radicals formed in the shock-heated H2/O2/Ar mixtures. The OH radicals were detected using the P(1)(5) line of (0,0) band of the A(exp 2) Sigma(+) from X(exp 2) Pi transition of OH at 310.023 nm (air). The data were analyzed with the aid of computer modeling. In the experiments great care was exercised to obtain high time resolution, linearity and signal-to-noise. The results are well represented by the Arrhenius expressions. The rate coefficient expression for reaction (1) obtained in this study is k(1) = (7.13 +/- 0.31) x 10(exp 13) exp(-6957+/- 30 K/T) cu cm/mol/s (1050 K less than or equal to T less than or equal to 2500 K) and a consensus expression for k(1) from a critical review of the most recent evaluations of k(1) (including our own) is k(1) = 7.82 x 10(exp 13) exp(-7105 K/T) cu cm/mol/s (960 K less than or equal to T less than or equal to 5300 K). The rate coefficient expression of k(2) is given by k(2) = (1.88 +/- 0.07) x 10(exp 14) exp(-6897 +/- 53 K/T) cu cm/mol/s (1424 K less than or equal to T less than or equal to 2427 K). For k(1), the temperature dependent A-factor and the correlation between the values of k(1) and the inverse reactant densities were not found. In the temperature range of this study, non-Arrhenius expression of k(2) which shows the upward curvature was not supported.

Ryu, Si-Ok↗