Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “kW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

High-Power Performance of a 100-kW Class Nested Hall Thruster

Operations of a three-channel 100-kW class nested Hall thruster at total power levels from 5 to 102 kW and discharge currents from 16 to 247 A were successful. The thruster was operated in all seven available channel combinations at discharge voltages of 300, 400, and 500 V and at current densities that were 0.60 and 0.95 of the nominal value. Additional test points were also collected at 1.20 the nominal current density. The thruster was throttled through a total of forty-six unique operating conditions. At each condition, thruster performance was measured using a high-power thrust stand designed to measure up to 8 N of thrust. From these thrust measurements, specific impulse and efficiency were calculated. All seven channel combinations showed similar performance at a given discharge voltage and current density. The largest thrust recorded was 5.42 N at 99 kW, 400 V discharge voltage. Total efficiency values 0.54 to 0.67, and total specific impulse ranged from 1800 seconds to 2650 seconds. Discharge current oscillations were also measured. Generally these oscillations increased on the inner and middle channels during multi-channel mode but stayed roughly a constant fraction of the channel discharge current for the outer channel in both single- and multi-channel operation. We also found that the thrust of the three channels firing together was not significantly higher than the sum of each channel _ring individually, a result that differs from what was found previously for nested Hall thrusters.

Hall, Scott J.↗

Wear Test of the 12.5-kW Advanced Electric Propulsion System Engineering Test Unit Hall Thruster

This work presents a summary of the first wear test of the 12.5 kW Advanced Electric Propulsion System Engineering Test Unit 2 (AEPS ETU-2) thruster produced by Aerojet Rocketdyne. The ETU-2 Wear Test accumulated approximately 730 hours of operation split between the nominal 600 V/12.5 kW condition and the 300 V/6.25 kW condition previously identified as the worst-case erosion condition.

Jason D. Frieman↗

Preliminary design of a 100 kW turbine generator

The National Science Foundation and the Lewis Research Center have engaged jointly in a Wind Energy Program which includes the design and erection of a 100 kW wind turbine generator. The machine consists primarily of a rotor turbine, transmission, shaft, alternator, and tower. The rotor, measuring 125 feet in diameter and consisting of two variable pitch blades operates at 40 rpm and generates 100 kW of electrical power at 18 mph wind velocity. The entire assembly is placed on top of a tower 100 feet above ground level.

Puthoff, R. L.↗

The 100 kW experimental wind turbine generator project

The Energy Research and Development Administration and the NASA Lewis Research Center engaged jointly in a Wind Energy Program which included the design and erection of a 100 kW wind turbine generator. This test machine consists of a rotor turbine, transmission, shaft, alternator, and tower. The rotor, measuring 125 feet in diameter and consisting of two variable pitch blades, operates at 40 rpm and generates 100 kW of electrical power at a wind velocity of 18 mph. The entire assembly is placed on top of a tower 100 feet above ground level. The machine was scheduled to be ready for operation in August, 1975.

Puthoff, R. L.↗

Experimental data and theoretical analysis of an operating 100 kW wind turbine

Part of the cooperative effort between NASA and ERDA has been the design and the erection of an experimental wind turbine by the NASA-Lewis Research Center. This 100 kW turbine, designated the Mod-O, is located at the NASA Plum Brook site near Sandusky, Ohio. Experimental test data have been correlated with analyses of turbine loads and complete system behavior of the 100 kW Mod-O wind turbine generator over a broad range of steady state conditions, as well as during transient conditions. The deficit in the ambient wind field due to the upwind tower turbine support structure was found to be very significant in exciting higher harmonic loads associated with the flapping response of the blade in bending.

Linscott, B. S.↗

The 40 KW of Solar Cell Modules for the Large Scale Production Task a Low Cost Silicon Solar Array Project

Forty kilowatts of solar cell modules was produced in this program. This is equivalent to 4123 modules. The average power output per module was 9.7 watts at 16.5 volts, 60 C and 100 mW/sq cm. The peak production rate was 200 modules per week which is equal to 1.9 kW per week. This rate was sustained for over four and one-half months and is equivalent to 100 kW per year. This final report covers the solar cell module design, electrical and power performance, module preproduction environmental test results, production and shipping schedule, program summary, and delivery. A cost analysis section is written. Particular emphasis on the percentage of labor and material utilized in constructing a solar cell module is presented. Also included are cost reduction recommendations.

Jones, G. T.↗

A 200-kW wind turbine generator conceptual design study

A conceptual design study was conducted to define a 200 kW wind turbine power system configuration for remote applications. The goal was to attain an energy cost of 1 to 2 cents per kilowatt-hour at a 14-mph site (mean average wind velocity at an altitude of 30 ft.) The costs of the Clayton, New Mexico, Mod-OA (200-kW) were used to identify the components, subsystems, and other factors that were high in cost and thus candidates for cost reduction. Efforts devoted to developing component and subsystem concepts and ideas resulted in a machine concept that is considerably simpler, lighter in weight, and lower in cost than the present Mod-OA wind turbines. In this report are described the various innovations that contributed to the lower cost and lighter weight design as well as the method used to calculate the cost of energy.

Source record↗

The kW power module evolution study: Executive summary

Using the Marshall Space Flight Center 25 kW Power Module (PM) reference design as a point of departure, the study defined evolutionary growth paths to 100 kW and above. A recommended development approach and initial configurations were described. Specific hardware changes from the reference design are recommended for the initial PM configuration to ensure evolutionary growth, improved replicability, and reduced cost. Certain functional changes are also recommended to enhance system capabilities.

Source record↗

25 kW power module evolution study

This paper presents a study of evolutionary growth concepts for the 25 kW power module to augment STS mission support future capabilities. The study aimed to establish user payload requirements, define evolution methods for system initial operational capability, and formulate a development program and conceptual designs. The payload requirements analysis focused on material processing in space, public services, and solar terrestrial observations; evolutionary system concepts were evaluated to derive the power module and system support requirements, and four reference orbits were used to construct the nominal program scenario. The mission accomodations analysis evaluated the capability of the nominal program scenario and associated power module concepts to meet user needs. Finally, the recommended modular design consisting of electric power, attitude control, thermal control, and command and data handling is described, and it is concluded that the 25 kW power module is a logical first step to support the near term NASA sortie and free-flyer mission requirements.

Overall, J. W., Jr.↗

Engineering aspects of a thermal control subsystem for the 25 kW power module

The paper presents the key trade study results, analysis results, and the recommended thermal control approach for the 25 kW power module defined by NASA. Power conversion inefficiencies and component heat dissipation results in a minimum heat rejection requirement of 9 kW to maintain the power module equipment at desired temperature levels. Additionally, some cooling capacity should be provided for user payloads in the sortie and free-flying modes. The baseline thermal control subsystem includes a dual-loop-pumped Freon-21 coolant with the heat rejected from deployable existing orbiter radiators. Thermal analysis included an assessment of spacecraft orientations, radiator shapes and locations, and comparison of hybrid heat pipe and all liquid panels.

Schroeder, P. E.↗

25-kW power module

The 25-kW power module design and operational characteristics and the benefits for payloads are presented. The module will allow the Shuttle Orbiter to be utilized on-orbit to its optimum capability of power and duration for sortie/Spacelab missions, and will provide central power-rich base for free-flyer payloads requiring increased electrical power and on-orbit stay-times of up to 5 years. Concepts of the module in the sortie and free-flyer modes are depicted with resource capabilities for experimentation in astronomy, solar physics, solar terrestrial observations, and materials processing which require long duration and/or high power missions. In the sortie mode operation the Orbiter fuel cell will be in an idle mode, with the 25-kW module providing payload power needs, and in the free-flyer mode the module will provide power needs to multiple payloads. Design considerations, the thermal control subsystem, the attitude control subsystem, command and data handling, and the electrical power subsystem are described.

Powell, L. E.↗

A 150 and 300 kW lightweight diesel aircraft engine design study

The diesel engine was reinvestigated as an aircraft powerplant through design study conducted to arrive at engine configurations and applicable advanced technologies. Two engines are discussed, a 300 kW six-cylinder engine for twin engine general aviation aircraft and a 150 kW four-cylinder engine for single engine aircraft. Descriptions of each engine include concept drawings, a performance analysis, stress and weight data, and a cost study. This information was used to develop two airplane concepts, a six-place twin and a four-place single engine aircraft. The aircraft study consists of installation drawings, computer generated performance data, aircraft operating costs, and drawings of the resulting airplanes. The performance data show a vast improvement over current gasoline-powered aircraft.

Brouwers, A. P.↗

Design study: A 186 kW lightweight diesel aircraft engine

The design of an aircraft engine capable of developing 186 kW shaft power at a 7620 m altitude is described. The 186 kW design takes into account expected new developments in aircraft designs resulting in a reassessment of the power requirements at the cruise mode operation. Based on the results of this analysis a three phase technology development program is projected resulting in production dates of 1985, 1992, and 2000.

Brouwers, A. P.↗

Study of multi-kW solar arrays for Earth orbit applications: Midterm performance review

Planar and concentrator solar array concepts capable of providing 300 kW to 1000 kW in low Earth orbit applications in the 1987 time period at an array recurring cost less than or equal to thirty dollars per watt are examined. Silicon and gallium arsenide solar cell applicability are evaluated. On-orbit maintenance by space shuttle is also investigated. Design configurations for the solar arrays and solar cells are recommended.

Source record↗

Operating characteristics of a 0.87 kW-hr flywheel energy storage module

Discussion is given of the design and loss characteristics of 0.87 kW-hr (peak) flywheel energy storage module suitable for aerospace and automotive applications. The maraging steel flywheel rotor, a 46-cm- (18-in-) diameter, 58-kg (128-lb) tapered disk, delivers 0.65 kW-hr of usable energy between operating speeds of 10,000 and 20,000 rpm. The rotor is supported by 20- and 25-mm bore diameter, deep-groove ball bearings, lubricated by a self-replenishing wick type lubrication system. To reduce aerodynamic losses, the rotor housing was evacuated to vacuum levels from 40 to 200 millitorr. Dynamic rotor instabilities uncovered during testing necessitated the use of an elastometric-bearing damper to limit shaft excursions. Spindown losses from bearing, seal, and aerodynamic drag at 50 millitorr typically ranged from 64 to 193 W at 10,000 and 20,000 rpm, respectively. Discharge efficiency of the flywheel system exceeded 96 percent at torque levels greater than 21 percent of rated torque.

Loewenthal, S. H.↗

Testing of YUH-61A helicopter transmission in NASA Lewis 2240-kW (3000-hp facility

A helicopter transmission that was being considered for the Army's Utility Tactical Transport Attack System (UTTAS) was tested in the NASA Lewis 2240-kW (3000-hp) test facility to obtain the transmission's operational data. The results will form a vibration and efficiency data base for evaluation similar-class helicopter transmissions. The transmission's mechanical efficiency was determined to be 98.7 percent at its rated power level of 2080 kW (2792 hp). At power levels up to 113 percent of rated the transmission displayed 56 percent higher vibration acceleration levels on the right input than on the left input. Both vibration signature analysis and final visual inspection indicated that the right input spiral-bevel gear had poor contact patterns. The highest vibration meter level was 52 g's rms at the accessory gear, which had free-wheeling gearsets. At 113 percent power and 100 percent rated speed the vibration meter levels generally ranged from 3 to 25 g's rms.

Mitchell, A. M.↗

Development and life-testing of 10 kW class thermal arcjet engines

A facility to develop and test thermal arcjet engines over extended periods of time has been constructed and is described in this paper. It consists of a large vacuum tank, high capacity vacuum pumps, a 100 kW power supply and a large ammonia propellant storage and delivery system. The facility is instrumented to measure electrical power dissipated in the engine, propellant mass flow rate and developed thrust. Pressures and temperatures up to 2400 K can also be measured. The entire facility is computer-controlled and can be operated unattended for many weeks. Two 30 kW thermal arcjet engines that have been designed, built and are being tested in this facility are also described.

Pivirotto, T. J.↗