Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “internal stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Investigation of the notch sensitivity of tailorable long fiber discontinuous prepreg composite laminates

Tailorable discontinuous fiber composite laminates provide relative formability beyond that of continuous fiber laminates, while achieving improved mechanical performance over comparable stochastic systems. Here, in this work, the notch sensitivity of engineered prepreg platelet molded composite (PPMC) laminates is investigated using the open-hole tension (OHT) test and compared to available data for stochastic PPMCs and continuous fiber laminates made with the same material. The press-formed thermoplastic composites (AS4/PEKK) were molded with a quasi-isotropic stacking sequence. The discontinuous PPMC laminate was found to be notch insensitive with OHT strengths ranging from 145.4 MPa (CV $=$ 7%) for d/w $=$ 0.5 to 229.3 MPa (CV $=$ 9%) for d/w $=$ 0.25. The highly ordered meso-structure of the engineered PPMC laminate yields comparatively excellent mechanical properties for relatively thin laminates in contrast to stochastic systems. Both net- and gross-section failures were observed for d/w $=$ 0.25, which suggests that the engineered PPMC laminates studied here maintain a degree of inherent, internal stress concentrations that compete with those caused by geometric features such as a circular hole. Computational simulations of the OHT tests with explicitly represented platelets were found to be in good agreement with experimental measurements. The progressive failure analysis was used to conduct a numerical investigation of the stacking sequence and platelet meso-morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Qualitative and quantitative analysis of neutron irradiation effects in SiC/SiC composites using X-ray computed tomography

Silicon carbide fiber-reinforced silicon carbide matrix (SiC/SiC) composites are candidate materials for cladding of light water reactor (LWR) fuels. Loss of fission product gas retention due to the formation of microcrack networks is considered a potential failure mechanism for SiC/SiC-cladded fuels. In this work, a variety of SiC/SiC composite tubes were irradiated with and without an LWR-relevant radial heat flux in the High Flux Isotope Reactor, followed by detailed characterization with X-ray computed tomography (XCT). This first set of XCT data for neutron-irradiated samples confirmed that the internal stresses arising from a combination of temperature gradients and irradiation-induced swelling act as the primary driver for cracking. Consequently, while the observed cracking patterns varied depending on the tube architectures, the sharp edges of relatively large pores were found to be the common stress concentrator. These findings are useful to help improve the design and manufacturing of SiC/SiC fuel claddings for reduced failure probability.

42 ENGINEERING↗
DOE OSTI2023

In-situ high energy X-ray diffraction study of deformation behavior in Nb nanoparticle-martensitic NiTi composite wire

Here, this study investigated the deformation behavior in Nb nanoparticle-martensitic NiTi composite wire during tensile loading by means of in-situ high-energy X-ray diffraction. Compared to Nb nanowires, the dispersedly distributed Nb nanoparticles have little effect on the transformation and deformation behaviors of NiTi matrix, causing the absence of R phase transformation and the occurrence of deformation twinning in NiTi matrix. Meanwhile, the occurrence of deformation twinning in NiTi matrix can reduce the shape strain to be coordinated by the unfavorable orientated martensite variants, and thus decreases the internal stress among NiTi martensite variants generated during martensite reorientation process. In addition, TEM result proved that Nb nanoparticles can achieve exceptionally large elastic strain in B19'-NiTi matrix (~4%), just as Nb nanowires. However, this large elastic strain (stress) will be released with the occurrence of NiTi deformation twinning.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Brazing characteristics, microstructure, and wettability of laser powder bed fusion additive manufactured GRCop-84 compared to CuCrZr and OFC, and brazing to titanium-zirconium-molybdenum alloy limiters

Laser Powder Bed Fusion (L-PBF) of Glenn Research Copper 84 (GRCop-84), a Cr 2 Nb (8 at. % Cr, 4 at. % Nb) precipitation hardened alloy, produces a fully dense, high conductivity alloy with a yield strength of 500 MPa and ultimate tensile strength (UTS) of 740 MPa with 20% elongation; superior to other competing copper alloys. Braze wetting characteristics of GRCop-84 with Ag-Cu-X, and Au-Cu brazes were similar to CuCrZr, but less than oxygen free copper. No difference in wetting was observed between infill and surface contour areas in L-PBF GRCop-84. Wet sanding to 240 grit (R a =0.24 µm) was considered the optimal surface condition. Silver diffusing through GRCop-84 depleted Cr 2 Nb precipitates from the copper grain and deposited agglomerations of coarsened precipitates within silver-rich regions of intergranular diffusion once a density threshold was reached. Microstructure modification was minimized with 50Au-50Cu braze implying that silver caused precipitate coarsening and agglomeration, and not high temperature exposure. Coarsened precipitates were observed on the surface within braze pools implying a contribution to braze wetting. Palcusil-25, Ticusil, CuSil-ABA, and 50Au-50Cu brazes were suitable for brazing to unplated Titanium-Zirconium-Molybdenum (TZM), while sulfamate nickel plating to allows wetting with CuSil or other non-active brazes. Additionally, vacuum brazing techniques were developed to join a 1 mm thick layer of TZM to the front of additive manufactured GRCop-84 waveguides considering the brazing characteristics of both GRCop-84, TZM, and internal stress from the difference in coefficient in thermal expansion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Topological origin of phase separation in hydrated gels

Depending on their composition, hydrated gels can be homogeneous or phase-separated, which, in turn, affects their dynamical and mechanical properties. However, the nature of the structural features, if any, that govern the propensity for a given gel to phase-separate remains largely unknown. Here, we argue that the propensity for hydrated gels to phase-separate is topological in nature. We employ reactive molecular dynamics simulations to model the early-age precipitation of calcium–alumino–silicate–hydrate (Csingle bondAsingle bondSsingle bondH) gels with varying compositions, i.e., (CaO) 1.7 (Al 2 O 3 ) x (SiO 2 ) 1 – x (H 2 O) 3.7 + x . By adopting topological constraint theory, we investigate the structural origin of phase separation in hydrated gels. We report the existence of a homogeneous-to-phase-separated transition, wherein Si-rich (x ≤ 0.10) Csingle bondAsingle bondSsingle bondH gels are homogeneous, whereas Al-rich (x > 0.10) Csingle bondAsingle bondSsingle bondH gels tend to phase-separate. Furthermore, we demonstrate that this transition is correlated to a topological flexible-to-rigid transition within the atomic network. Finally, we reveal that the propensity for topologically-overconstrained gels to phase-separate arises from the existence of some internal stress within their atomic network, which acts as an energy penalty that drives phase separation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Alkali-activated slag (AAS) and OPC-based composites containing crumb rubber aggregate: Physico-mechanical properties, durability and oxidation of rubber upon NaOH treatment

Value-added utilization of waste tires in cementitious materials has been studied for decades, whereas the synergy between rubber and alkali-activated cements deserves more investigations. To this end, we compared physico-mechanical and durability properties of alkali-activated slag (AAS) and OPC-based composites containing NaOH-pretreated/as-received crumb rubber (CR). It was found that the incorporation of CR had both positive and negative effects on specimens due to its special attributes. CR reduced electrical conductivity which was associated with the ion transport ability, since it worked as an electrical insulator and increased hydrophobicity of pore walls. The sulfate expansion decreased with CR content because the flow of sulfate ions was demobilized, and the flexibility of CR relieved the internal stress. CR also improved the freeze-thaw durability of composites if the total CR content was less than 30% in specimens. However, the low Young's modulus of CR impaired the compressive strength and failed to effectively control the total shrinkage upon drying. The composites with CR must avoid high temperature exposure which resulted in the pyrolysis of rubber. In addition, the NaOH pretreatment enhanced adhesion between CR and hydrated cement and improved overall performances of composites. The FTIR spectra confirmed the NaOH-induced accelerated oxidation of CR surface and the generation of polar functional groups including carbonyl and carboxyl groups, increasing the total surface energy of rubber. More importantly, the alkali-activation process for AAS could treat the CR aggregate in the meantime, which means the use of CR in alkali-activated cements does not require the pretreatment of CR before blending.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Twin nucleation and growth in hexagonal close-packed metals: The role of slip-mediated plasticity on twin embryo formation and evolution

Twinning is a key deformation mechanism in hexagonal close-packed (hcp) metals, which are typified by a lack of easily activated slip systems that can accommodate a general state of loading. Pragmatically, the nucleation and evolution of twin domains occurs concomitantly with slip, such that the eventual twin network is conditioned by both external and internal stresses resulting, among others, from the evolution of dislocations. However our understanding of the interplay between dislocations, and twin nucleation and stability remains limited. This work focuses on elucidating the influence of dislocation-mediated plasticity on the formation, growth, and stability of twin embryos. First, a new mesoscale spectral crystal plasticity-twinning framework is developed and used to quantify the change in the free energy landscape following the nucleation {$10\bar{1}2$} of twins in Mg. Representative twin morphologies are modeled under conditions of limited and profuse slip activity, which are emulative of small- and bulk-scale samples, respectively. Then, the driving traction profiles around twin embryos are investigated via a sharp interface approach to obtain insights into how concurrent slip-mediated plasticity can influence the growth/stabilization of nanometric twins. The driving traction profiles are further utilized to determine the stability of twin embryos post loading. The initial dislocation density in the samples, and within the different domains (i.e., twin vs. parent), is seen to have a significant effect on the twin nucleation stress. Namely, the activation of high levels of concomitant plasticity in the parent grain is seen to significantly drive the formation of nanometric twin nuclei at stresses as low as 250 MPa. Further, the sharp interface analysis reveals that profuse plasticity in the parent grain simultaneously alters the forward and back stresses, such that the magnitude/polarity of the driving tractions become increasingly favorable for nanometric twin growth when slip is active. Finally, prior plasticity in the parent grain is seen to result in favorable driving tractions for nanometric twin growth, even at applied stresses as low as ~ 100 MPa. In conclusion, these results are in stark contrast to a case without any dislocations, wherein applied stresses as high as ~ 500 MPa are necessary to grow the twin domains.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Intrinsic two-way shape memory effect in a Ni-Mn-Sn metamagnetic shape memory microwire

We report an intrinsic two-way shape memory effect with a fully recoverable strain of 1.0% was achieved in an as-prepared Ni 50 Mn 37.5 Sn 12.5 metamagnetic shape memory microwire fabricated by Taylor-Ulitovsky method. This two-way shape memory effect is mainly owing to the internal stress caused by the retained martensite in austenite matrix, as revealed by transmission electron microscopy observations and high-energy X-ray diffraction experiments. After superelastic training for 30 loading/unloading cycles at room temperature, the amount of retained martensite increased and the recoverable strain of two-way shape memory effect increased significantly to 2.2%. Furthermore, a giant recoverable strain of 11.2% was attained under a bias stress of 300 MPa in the trained microwire. These properties confer this microwire great potential for micro-actuation applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

An integrated statistical-thermodynamic model for fission gas release and swelling in nuclear fuels

Here, we propose a new model for burst fission gas release induced by microcracking in ceramic nuclear fuels such as uranium dioxide. The model stipulates that the densities of defects in the fuel material, such as microcracks and fission gas bubbles on grain boundaries, evolve in accordance with the second law of thermodynamics. Central to the model is the notion of an effective temperature, conjugate to the configurational entropy of the fuel material, and directly linked to the burnup. The model predicts that microcracking, driven by the internal stress state of the fuel material, reduces the bubble storage capacity of grain boundaries, and accounts for burst fission gas release during rapid temperature transients that simulate power transients, reactor startup, and loss-of-coolant accident conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Grain-resolved temperature-dependent anisotropy in hexagonal Ti-7Al revealed by synchrotron X-ray diffraction

Hexagonal metals have anisotropic coefficients of thermal expansion causing grain-level internal stresses during heating. High energy x-ray diffraction microscopy, a non-destructive, in situ, micromechanical and microstructural characterization technique, has been used to determine the anisotropic coefficients of thermal expansion (CTEs) for Ti-7Al. Two samples of polycrystalline α-phase Ti-7Al were continuously heated from room temperature to 850 °C while far-field HEDM scans were collected. The results showed a change in the ratio of the CTEs in the ‘a’ and ‘c’ directions which explains discrepancies found in the literature. The CTE additionally appears to be affected by the dissolution of α 2 precipitates. Analysis of the grain-resolved micromechanical data also shows reconfiguration of the grain scale stresses likely due to anisotropic expansion driving crystallographic slip.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of laser scanning speed on the microstructure, phase transformation and mechanical property of NiTi alloys fabricated by $\mathrm{LPBF}$

This study investigated the effects of laser scanning speed on the microstructure, phase transformation and properties of NiTi alloys fabricated by laser powder bed fusion (LPBF). In this study, the contributions of metallurgical factors under different scanning speeds, such as Ni evaporation, Ni4Ti3 precipitation, dislocations and internal stress, to the transformation temperature and transformation latent heat were clarified through specially designed experiments. Ni evaporation is found to have the most profound effect, followed by precipitation. Increasing scanning speed is found to reduce Ni loss, thus cause less increase in the transformation temperature and transformation heat of the LPBF-NiTi alloys. Increasing scanning speed also increases the microstructure non-uniformity and thus widens the transformation temperature interval. The orientations of residual stress exhibit strong crystallographic stiffness dependence. The LPBF-NiTi alloys with different scanning speeds all exhibited high strains (>13.4%) and excellent shape memory effect. A LPBF-NiTi honeycomb structure exhibited 96% shape recovery rate after a 60% pre-compressive deformation. Besides, there is an optimum scanning speed for minimum porosity and smallest average pore size. However, the pore structure is found to have weak influence on the tensile behaviour of the LPBF-NiTi alloys, possibly due to the high defect tolerance of the martensitic transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Pressure Heterogeneity and Material Utilization in Thin-Film Solid-State Cathodes

Intimate interfacial contact between the solid electrolyte and the cathode active material is critical for maximizing cathode utilization in solid-state batteries. However, volume changes during electrochemical cycling induce internal stresses that drive interfacial degradation, particularly under nonuniform stack pressure. In this study, we employ in situ energy-dispersive X-ray diffraction tomography to visualize and quantify reaction heterogeneities across a 3 mm-diameter solid-state cathode with a well-defined interface. Our results reveal that regions under a lower stack pressure exhibit reduced material utilization and reversibility, which negatively affect the high-pressure regions. Interfacial degradation further impedes lithium-ion transport and amplifies microscale reaction heterogeneity. These findings highlight the critical role of stack pressure distribution in governing interfacial stability and electrochemical performance, offering important design insights into practical solid-state battery systems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Three-dimensional characterization of modifications in sapphire exposed to laser-induced damage using multimodal spectral microimaging

Sapphire (Al 2 O 3 ) is a commonly used dielectric material with many applications in lasers and optical systems. Owing to its high resistivity to laser induced damage, it is particularly suitable for use in high power laser systems. This work focuses on developing techniques to characterize material modifications in sapphire. These techniques were applied following localized laser induced ablation, commonly referred to as laser-damage, resulting from exposure to single 100-ps and 6-ns pulses. Measurements of fluorescence-based piezospectroscopy and confocal Raman microscopy were performed with spatial resolution on the order of 1 μ m. Raman microscopy reveals that the relaxation of material exposed to the rapid laser heating, elastic and viscoplastic deformation, melting, and solidification leads to the formation of a polycrystalline material phase. In addition, narrowband fluorescence lines, referred to as R 1 and R 2 , exhibit pressure-sensitive changes to their spectral profiles, allowing 3D internal stresses to be recorded with spatial resolution of the order of a few micrometers.

Laser-damage↗
DOE OSTI2020

Shock recompaction of spall damage

Spall fracture is a high strain-rate damage phenomenon associated with shock or impulsive loading events. When a material that has been subjected to shock compression is allowed to release, rarefaction waves propagate into the sample and reduce the internal stress to zero. If multiple rarefaction waves intersect, they generate tension which, if sufficient, can nucleate voids in the material. It has been observed in several works investigating spall fracture that although the shock-wave profiles suggested spall occurred, imaging of the recovered sample revealed no voids or cracks. In this study, we aim to determine whether a second shock event could recompact existing spall damage, and if so, what form does the microstructure at the recompaction interface have? Through a series of gas-gun flyer-plate impact experiments, we demonstrate that modest shock stresses of 2 GPa–3 GPa are enough to both fully compact a damaged copper target back to a state of zero porosity and, furthermore, drive recrystallization of the interface such that there is a new bond formed where the free surfaces were brought together.

42 ENGINEERING↗
DOE OSTI2023

Scientific machine learning for modeling and simulating complex fluids

The formulation of rheological constitutive equations—models that relate internal stresses and deformations in complex fluids—is a critical step in the engineering of systems involving soft materials. While data-driven models provide accessible alternatives to expensive first-principles models and less accurate empirical models in many engineering disciplines, the development of similar models for complex fluids has lagged. The diversity of techniques for characterizing non-Newtonian fluid dynamics creates a challenge for classical machine learning approaches, which require uniformly structured training data. Consequently, early machine-learning based constitutive equations have not been portable between different deformation protocols or mechanical observables. Here, we present a data-driven framework that resolves such issues, allowing rheologists to construct learnable models that incorporate essential physical information, while remaining agnostic to details regarding particular experimental protocols or flow kinematics. These scientific machine learning models incorporate a universal approximator within a materially objective tensorial constitutive framework. By construction, these models respect physical constraints, such as frame-invariance and tensor symmetry, required by continuum mechanics. We demonstrate that this framework facilitates the rapid discovery of accurate constitutive equations from limited data and that the learned models may be used to describe more kinematically complex flows. This inherent flexibility admits the application of these “digital fluid twins” to a range of material systems and engineering problems. We illustrate this flexibility by deploying a trained model within a multidimensional computational fluid dynamics simulation—a task that is not achievable using any previously developed data-driven rheological equation of state.

Science & Technology - Other Topics↗
DOE OSTI2025

Strong, ductile, and hierarchical hetero-lamellar-structured alloys through microstructural inheritance and refinement

The strength−ductility trade-off exists ubiquitously, especially in brittle intermetallic-containing multiple principal element alloys (MPEAs), where the intermetallic phases often induce premature failure leading to severe ductility reduction. Hierarchical heterogeneities represent a promising microstructural solution to achieve simultaneous strength−ductility enhancement. However, it remains fundamentally challenging to tailor hierarchical heterostructures using conventional methods, which often rely on costly and time-consuming processing. Here, we report a multiscale microstructural inheritance and refinement strategy to process “structural hierarchy precursors” in as-cast heterogeneous Al 0.7 CoCrFeNi MPEAs, which lead directly to a hierarchical hetero-lamellar structure (HLS) after simple rolling and annealing. Interestingly, it takes only 10 min of annealing time, two orders of magnitude less than that required to render the state-of-the-art properties during conventional processing of Al 0.7 CoCrFeNi, for us to achieve record-high strength−ductility combinations via the hierarchical HLS design that sequentially stimulates multiple unusual deformation and reinforcement mechanisms. In particular, the HLS-enabled high hetero-deformation-induced (HDI) internal stress triggers profuse <111>-type dislocations on over five independent slip systems in the supposedly brittle intermetallic phase and activates extensive stacking faults (SFs) and nanotwinning in the adjoining soft phase with a rather high SF energy. These unexpected, dynamically reinforcing hetero-deformation mechanisms across multiple length scales facilitate high sustained HDI strain hardening, along with a salient microcrack-mediated extrinsic ductilization effect, suggesting that the proposed microstructural inheritance and refinement strategy provides an efficient, fast, and low-cost approach to overcome the strength−ductility trade-off in a broad range of structural materials.

Science & Technology - Other Topics↗
DOE OSTI2021

Design and Analysis of an Advanced Three-Point Bend Test Approach for Miniature Irradiated Disk Specimens

Candidate tungsten armor materials in a magnetic confinement fusion device must be able to withstand thermal variation that leads to internal stresses caused by the impinging heat load. In addition, the thermomechanical properties of these materials are degraded by irradiation-induced defect accumulation. Fission reactor–based irradiation data are used to predict the fusion neutron damage and property change. This study examines the motivation and design of a custom-designed three-point bend test for neutron-irradiated disk specimens that are 3 mm in diameter to be able to define the flexural strength of advanced tungsten materials, alloys, and composites—and to the extent that embrittlement occurs after neutron irradiation. The theory provided shows a calculation for the flexural deflection and shear deflection due to the small-geometry constraints. A finite element deformation analysis is performed to evaluate the mechanical stress field of disk bend specimens. The stress values above 80% of the maximum stress are concentrated in 2.4 mm of the 3.0-mm length of the centerline across the tungsten disk diameter. A bend test fixture has been designed and fabricated to enable testing of these specimens with precisely engineered tolerance and minimal machine compliance. This fixture will be able to be placed inside a universal testing frame at elevated temperatures for the mechanical property evaluation of future neutron-irradiated disk specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Buckling-induced interaction between circular inclusions in an infinite thin plate

Design of slender artificial materials and morphogenesis of thin biological tissues typically involve stimulation of isolated regions (inclusions) in the growing body. These inclusions apply internal stresses on their surrounding areas that are ultimately relaxed by out-of-plane deformation (buckling). Here, we utilize the Föppl-von Kármán model to analyze the interaction between two circular inclusions in an infinite plate that their centers are separated a distance of 2ℓ. In particular, we investigate a region in phase space where buckling occurs at a narrow transition layer of length ℓ D around the radius of the inclusion, $R (ℓ_D \ll R)$. We show that the latter length scale defines two regions within the system, the close separation region, $ℓ – R \sim ℓ_D$, where the transition layers of the two inclusions approximately coalesce, and the far separation region, $ℓ – R \gg ℓ_D$. While the interaction energy decays exponentially in the latter region, $E_{\text{int}} ∝ e^{– (ℓ – R)/ℓ_D}$, it presents nonmonotonic behavior in the former region. While this exponential decay is predicted by our analytical analysis and agrees with the numerical observations, the close separation region is treated only numerically. In particular, we utilize the numerical investigation to explore two different scenarios within the final configuration: The first where the two inclusions buckle in the same direction (up-up solution) and the second where the two inclusions buckle in opposite directions (up-down solution). We show that the up-down solution is always energetically favorable over the up-up solution. In addition, we point to a curious symmetry breaking within the up-down scenario; we show that this solution becomes asymmetric in the close separation region.

42 ENGINEERING↗