Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interfacial resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

All Solid-State Li/LLZO/LCO Battery Enabled by Alumina Interfacial Coating

Li 7 La 3 Zr 2 O 12 (LLZO) garnet-type lithium-ion conductors are being investigated as a promising solid electrolyte for solid-state lithium batteries. To enable a functional all-solid-state configuration intensive investigations are needed to reduce the cathode/electrolyte interfacial resistance which contributes the most to cell performance loss. Among the commercial cathode materials investigated so far, LiCoO 2 (LCO) is one of the most stable with garnet electrolytes as only a superficial reaction has been detected between the two materials. However, even this minor reaction would block the Li-ion transport through the interface, resulting in deteriorated cell performance. In this work, we demonstrate that a thin aluminum oxide layer (5 nm) can be an effective interlayer to impede the formation of a harmful interphase and enable facile Li-ion transfer between LCO and the LLZO garnet. Room-temperature-sputtered LCO thin films were employed to form an interface with the garnet electrolyte and annealed at 800 °C to reveal the effect of the interfacial reaction on the Li-ion transfer across the interface. An aluminum oxide layer was then introduced between LCO and the garnet electrolyte by sputtering a metallic aluminum layer which is then annealed together with the upper LCO layer in oxygen, or by direct atomic layer deposition of the oxide. Compared to the LCO/LLZO/Li cells without an aluminum oxide interlayer, those with the interlayer exhibited improved performance, i.e., a stable discharge capacity of up to 90 mAh/(g LCO) at a C/10 rate, a rate capability up to 1.68C and a stable galvanostatic cycling at 0.1C for over 100 cycles with a discharge capacity fade rate of 0.15% per cycle. It was determined that aluminum diffused into the LCO layer after preventing the initial detrimental reaction between LCO and the LLZO garnet from happening during high temperature annealing, suggesting that the coating does not have to remain a physically blocking layer during cycling to function.

Electrochemistry↗
DOE OSTI2026

ThermoPI—an Online Tool to Calculate Heat Transfer Through Foam Insulation

Thermal insulation materials with ultra-low effective thermal conductivity are crucial for a multitude of applications. Over the years, a significant amount of experimental work has been dedicated to creating new insulation materials with low thermal conductivity. Similarly, substantial efforts have been made to enhance the theoretical understanding of thermal transport mechanisms in thermal insulation materials and to push the boundaries of lower thermal conductivity. However, ample room remains for enhancing the thermal resistivity of closed-cell foam insulations. To aid in the development of ultra-low effective thermal conductivity foam insulations, Oak Ridge National Laboratory has introduced a unique online tool, ThermoPI. This tool calculates not only the effective thermal conductivity but also the thermal conductivity components for porous materials, including gases, solids, and radiative, based on the materials’ structural information (e.g., porosity, pore size, gas species, pressure, solid species, pore geometry, and temperature).This tool collected and improved the existing theoretical models for thermal insulation materials’ gas, solid, and radiative thermal conductivity. These improved models have been validated with experimental data. Effective medium theory and sound velocity softening effects are considered for solid thermal conductivity. The built-in solid materials include polystyrene, polyurethane, polyethylene, and silica. Users are allowed to input new solid materials that are not built inside the tool. For gas thermal conductivity, the subcontinuum Knudsen effect is considered. In addition to several built-in gases, users can input new gases. For solid and radiative thermal conductivity calculations, several models are available to select, and the tool can determine the best model to choose based on the materials that users input. Users are also allowed to change selections manually. In addition, the tool can also calculate the effect of interfacial resistance on the overall thermal conductivity of layered materials. This work will elaborate on the tool and discuss how it can guide the development of new insulation products.

Shrestha, Som [ORNL] (ORCID:0000000183993797)↗
DOE OSTI2021

Dual-Solvent Li-Ion Solvation Enables High-Performance Li-Metal Batteries

Novel electrolyte designs to further enhance the lithium (Li) metal battery cyclability are highly desirable. Here, fluorinated 1,6-dimethoxyhexane (FDMH) is designed and synthesized as the solvent molecule to promote electrolyte stability with its prolonged –CF 2 – backbone. Meanwhile, 1,2-dimethoxyethane is used as a co-solvent to enable higher ionic conductivity and much reduced interfacial resistance. Combining the dual-solvent system with 1 m lithium bis(fluorosulfonyl)imide (LiFSI), high Li-metal Coulombic efficiency (99.5%) and oxidative stability (6 V) are achieved. Using this electrolyte, 20 µm Li||NMC batteries are able to retain ≈80% capacity after 250 cycles and Cu||NMC anode-free pouch cells last 120 cycles with 75% capacity retention under ≈2.1 µL mAh -1 lean electrolyte conditions. Such high performances are attributed to the anion-derived solid-electrolyte interphase, originating from the coordination of Li-ions to the highly stable FDMH and multiple anions in their solvation environments. This work demonstrates a new electrolyte design strategy that enables high-performance Li-metal batteries with multisolvent Li-ion solvation with rationally optimized molecular structure and ratio.

25 ENERGY STORAGE↗
DOE OSTI2025

Interlayer Design for Halide Electrolytes in All‐Solid‐State Lithium Metal Batteries

Abstract All‐solid‐state lithium‐metal batteries (ASSLMBs) are promising for transportation electrification due to their superior safety and high energy density. Lithium halide electrolytes provide excellent processing flexibility, high ionic conductivity, and anodic stability (>4.1 V), making them highly compatible with high‐voltage cathodes, surpassing sulfide electrolytes (<2.1 V). Nevertheless, halide electrolytes suffer from low cathodic stability and form an electronically conductive interphase with lithium, resulting in a critical current density (CCD) of nearly zero. Herein, Li 3 YbCl 6 electrolytes are synthesized that are kinetically stable with lithium by forming an electronic insulating solid electrolyte interphase. Guided by critical overpotential criteria, a PI 3 interlayer is designed that transforms into Li 6 PI 3 upon contact with lithium, substantially reducing the interfacial resistance of Li 3 YbCl 6 against lithium to 34 Ω and achieving a high critical overpotential of 114 mV. By substituting Yb with Lu, Li 3 LuCl 6 electrolytes with Li 6 PI 3 interlayers reach a CCD of 1.0 mA cm −2 at a capacity of 1.0 mAh cm −2 , comparable to sulfide electrolytes but with higher oxidation stability. Additionally, Li 6 PI 3 enables stable cycling of Li//Li cells with Li 3 LuCl 6 electrolytes at 0.5 mA cm −2 for 400 cycles and maintains 86.5% capacity in Li//LiCoO 2 cells after 220 cycles at 30 °C, paving the way for high‐performance ASSLMBs.

Chemistry↗
DOE OSTI2025

Manganese‐Based Spinel Cathodes: A Promising Frontier for Solid‐State Lithium‐Ion Batteries

Recently, all-solid-state lithium-ion batteries (ASSLIBs), which exhibit improved safety and enhanced energy density compared to conventional commercialized lithium-ion batteries (LIBs), thereby have garnered extensive research interest. Among the promising cathode candidates, Mn-based spinel cathodes LiMn 2 O 4 (LMO) and LiNi 0.5 Mn 1.5 O 4 (LNMO), with the unique characteristics of low cost, structural stability, and 3D Li-ion diffusion channels, have demonstrated excellent performance in LIBs and presented great potential in ASSLIBs applications. However, several challenges, including structural degradations, poor interfacial contact, large interfacial resistance, and Mn-dissolution/diffusion during the electrochemical cycling, hinder their practical applications and commercialization in the ASSLIBs. Particularly, the high-voltage LNMO cathodes suffer from the challenge of electrochemical incompatibility with most of the solid-state electrolytes (SSEs). Herein, the spinel structure, the electrochemical behavior, and the structural degradation of the LMO/LNMO are explored. The characteristics and recent progress of the mitigating strategies to the challenges of various SSEs, including polymer-, oxide-, composite-, sulfide-, halide-, and LiPON-based SSEs, are introduced when paired with LMO/LNMO. Finally, the directions for future research to advance Mn-based spinel cathodes and fulfill the requirements of the next-generation ASSLIBs are also discussed.

Dou, Yu [Concordia University, Montreal, QC (Canad↗
DOE OSTI2022

Recent Advances in Conduction Mechanisms, Synthesis Methods, and Improvement Strategies for Li 1+ x Al x Ti 2-x (PO 4 ) 3 Solid Electrolyte for All-Solid-State Lithium Batteries

With the increasing use of Li batteries for storage, their safety issues and energy densities are attracting considerable attention. Recently, replacing liquid organic electrolytes with solid-state electrolytes (SSE) has been hailed as the key to developing safe and high-energy-density Li batteries. In particular, Li 1+ x Al x Ti 2- x (PO4) 3 (LATP) has been identified as a very attractive SSE for Li batteries due to its excellent electrochemical stability, low production costs, and good chemical compatibility. However, interfacial reactions with electrodes and poor thermal stability at high temperatures severely restrict the practical use of LATP in solid-state batteries (SSB). Herein, a systematic review of recent advances in LATP for SSBs is provided. Here, this review starts with a brief introduction to the development history of LATP and then summarizes its structure, ion transport mechanism, and synthesis methods. Challenges (e.g., intrinsic brittleness, interfacial resistance, and compatibility) and corresponding solutions (ionic substitution, additives, protective layers, composite electrolytes, etc.) that are critical for practical applications are then discussed. Last, an outlook on the future research direction of LATP-based SSB is provided.

25 ENERGY STORAGE↗
DOE OSTI2025

Novel Zwitterionic Polyurethane-in-Salt Electrolytes with High Ion Conductivity, Elasticity, and Adhesion for High-Performance Solid-State Lithium Metal Batteries

This study presents a novel polymer-in-salt (PIS) zwitterionic polyurethane-based solid polymer electrolyte (zPU-SPE) that offers high ionic conductivity, strong interaction with electrodes, and excellent mechanical and electrochemical stabilities, making it promising for high-performance all solid-state lithium batteries (ASSLBs). The zPU-SPE exhibits remarkable lithium-ion (Li+) conductivity (3.7 × 10⁻⁴ S cm−1 at 25 °C), enabled by exceptionally high salt loading of up to 90 wt.% (12.6 molar ratio of Li salt to polymer unit) without phase separation. It addresses the limitations of conventional SPEs by combining high ionic conductivity with a Li+ transference number of 0.44, achieved through the incorporation of zwitterionic groups that enhance ion dissociation and transport. The high surface energy (338.4 J m−2) and elasticity ensure excellent adhesion to Li anodes, reducing interfacial resistance and ensuring uniform Li+ flux. When tested in Li||zPU||LiFePO₄ and Li||zPU||S/C cells, the zPU-SPE demonstrated remarkable cycling stability, retaining 76% capacity after 2000 cycles with the LiFePO4 cathode, and achieving 84% capacity retention after 300 cycles with the S/C cathode. Molecular simulations and a range of experimental characterizations confirm the superior structural organization of the zPU matrix, contributing to its outstanding electrochemical performance. The findings strongly suggest that zPU-SPE is a promising candidate for next-generation ASSLBs.

Wang, Kun↗
DOE OSTI2020

Enhanced Surface Interactions Enable Fast Li + Conduction in Oxide/Polymer Composite Electrolyte

Abstract Li + ‐conducting oxides are considered better ceramic fillers than Li + ‐insulating oxides for improving Li + conductivity in composite polymer electrolytes owing to their ability to conduct Li + through the ceramic oxide as well as across the oxide/polymer interface. Here we use two Li + ‐insulating oxides (fluorite Gd 0.1 Ce 0.9 O 1.95 and perovskite La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 2.55 ) with a high concentration of oxygen vacancies to demonstrate two oxide/poly(ethylene oxide) (PEO)‐based polymer composite electrolytes, each with a Li + conductivity above 10 −4 S cm −1 at 30 °C. Li solid‐state NMR results show an increase in Li + ions (>10 %) occupying the more mobile A2 environment in the composite electrolytes. This increase in A2‐site occupancy originates from the strong interaction between the O 2− of Li‐salt anion and the surface oxygen vacancies of each oxide and contributes to the more facile Li + transport. All‐solid‐state Li‐metal cells with these composite electrolytes demonstrate a small interfacial resistance with good cycling performance at 35 °C.

Wu, Nan↗
DOE OSTI2020

NASICON Li 1.2 Mg 0.1 Zr 1.9 (PO 4 ) 3 Solid Electrolyte for an All‐Solid‐State Li‐Metal Battery

Abstract A thin solid electrolyte with a high Li + conductivity is used to separate the metallic lithium anode and the cathode in an all‐solid‐state Li‐metal battery. However, most solid Li‐ion electrolytes have a small electrochemical stability window, large interfacial resistance, and cannot block lithium‐dendrite growth when lithium is plated on charging of the cell. Mg 2+ stabilizes a rhombohedral NASICON‐structured solid electrolyte of the formula Li 1.2 Mg 0.1 Zr 1.9 (PO 4 ) 3 (LMZP). This solid electrolyte has Li‐ion conductivity two orders of magnitude higher at 25 °C than that of the triclinic LiZr 2 (PO 4 ) 3 . 7 Li and 6 Li NMR confirm the Li‐ions in two different crystallographic sites of the NASICON framework with 85% of the Li‐ions having a relatively higher mobility than the other 15%. The anode–electrolyte interface is further investigated with symmetric Li/LMZP/Li cell testing, while the cathode–electrolyte interface is explored with an all‐solid‐state Li/LMZP/LiFePO 4 cell. The enhanced performance of these cells enabled by the Li 1.2 Mg 0.1 Zr 1.9 (PO 4 ) 3 solid electrolyte is stable upon repeated charge/discharge cycling.

Zhou, Qiongyu↗
DOE OSTI2026

Impact of Salt Chemistry and Interlayer Architecture on Solid Electrolyte Interphase Composition and Performance

Reversible lithium metal anodes require interphases that are chemically stable, mechanically robust, and compatible with scalable processing. Here, we use slot-die-coated, salt-rich PEO interlayers to design SEI nanolayers on Cu current collectors and isolate how salt anion chemistry controls interphase composition and lithium plating/stripping behavior in architectures relevant to Li plating and anode-free cells. Mesoscale modeling shows that dendrite initiation at SEI defects is governed by a tradeoff among interphase thickness, ionic conductivity, and stiffness through defect-driven current focusing, motivating controlled formation from thin precursor layers. Using UHV-transferred XPS and ToF-SIMS depth profiling after controlled Li deposition, we find that fluorinated sulfonylimide salts (LiTFSI, LiFSI) form mixed inorganic/organic interphases containing LiF and PEO-derived alkoxides, with LiFSI producing a more LiF-dominant Li-facing surface than LiTFSI under identical conditions. In contrast, LiNO 3 -containing interlayers yield a comparatively thick nitrate-derived interphase that reduces upon Li contact to an N-rich inorganic layer (Li–N/N 3− , LiN x O y ). In Cu| |Li cells, these designed interlayers reduce interfacial resistance and improve Coulombic efficiency (CE) and critical current density (CCD) relative to uncoated controls, with LiFSI- and LiNO 3 -based interlayers providing the highest CE/CCD. Overall, the results demonstrate a manufacturing-relevant approach to engineer SEI nanolayers by salt chemistry, providing pathways to improve reversible lithium metal anodes while reducing reliance on LiTFSI.

anion chemistry↗
DOE OSTI2020

Predicting mesoscale spectral thermal conductivity using advanced deterministic phonon transport techniques

We present a review, demonstration and simulation of phonon transport for the purposes of predicting materials performance at the mesoscale. We focus primarily on the development and implementation of a unified methodology to enable predictive heat transport. We report on the current state of the art as it pertains to deterministic phonon transport methodologies, discussing various topics concerning phonons. In application, we focus on the Self-Adjoint Angular Flux (SAAF) formulation of the Boltzmann transport equation for phonons, and develop the spatial, angular, and material property discretization required to accurately simulate the predictive physics of heat transport in dielectrics. We discuss thermal interfacial resistance and present our formulation of the diffuse mismatch model for simulating phonon interactions at internal boundaries. We have recently developed a deterministic, spectral phonon transport method for predicting effective thermal conductivity ($\kappa_{\textrm{eff}}$), using Bose-Einstein source terms coupled through an average material temperature. In this method, we introduce a closure term to the phonon transport system which acts as a redistribution function for the total energy of the system, and serves as a guide for the amount of non-equilibrium behavior occurring in the system. This method predicts thermal conductivity and equilibrium temperature distributions in homogeneous and heterogeneous materials using data generated by ab initio density functional theory methods. We employ polarization, density of states and full dispersion spectra to resolve thermal conductivity with numerous angular and spatial discretizations. Our implementation utilizes a Richardson iteration on a modified version of the phonon scattering source. The equations associated with this method are solved via a modification of traditional source iteration. We compare the performance of source iteration applied to an existing uncoupled, traditional SAAF method to our new method and comment on the iterative performance of each. We observe ballistic and diffusive phonon scattering as acoustic thickness of the domain changes, and are able to make comparisons between the accuracy and efficiency of both methods.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Wet-chemical synthesis of Li7P3S11 with tailored particle size for solid state electrolytes

The small-size solid-state electrodes (SSEs) with high Li+ conductivity play an important role in reducing the interfacial resistance between electrode materials and SSEs and defects between SSEs. As one of the most conductive sulfide based ionic conductors, scalable synthesis of Li7P3S11 with controllable particle sizes is highly desired but rarely reported. Here, we report a facile wet-chemical synthesis method to prepare Li7P3S11 SSEs with variable sizes for all-solid-state lithium batteries (ASSLBs). By fully dissolving 70Li2S-30P2S5 precursors in ethyl acetate solution, the particle size of Li7P3S11 can be manipulated into as small as ~110 nm and high Li+ conductivity of 1.05 mS cm-1 can be achieved. A systematical mechanistic study of solvent effects suggests that the controlled particle sizes are attributed to the excellent solvability and low binding energy of ethyl acetate solvent toward solutes. Moreover, this generic method can be extended to the facilely synthesis of Li3PS4 nanoparticles with an average size of ~200 nm and high Li+ conductivity of 0.1 mS cm-1.

Zhou, Jianbin↗
DOE OSTI2024

Ion transport in composites of binary electrolyte and single ion conductor—A chronoamperometry study

Composite electrolytes for lithium batteries typically combine materials with very different mechanical properties and ionic transport mechanisms and the degree to which these two phases affect each other is not well understood. In this work we used numerical simulations and experiments to investigate the transport in composite electrolytes consisting of polyethylene oxide (PEO) with Lithium bis-triuoromethanesulfonimide (LiTFSI) and Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP) lithium ion conducting glass-ceramic particles. In particular we are interested in how the introduction of a single ion conductor (SIC) changes the salt concentration gradients in the polymer electrolyte (PE) under applied potential. To study this, we performed numerical simulations and chronoamperometry experiments in electrolytes with different arrangements of the SIC and PE phases, i.e. layers and particulate composites. The results show that the particulate composites have the highest concentration gradients and take the longest time to reach steady state current. Furthermore, the high concentration gradient can be exacerbated by a high SIC/PE interfacial resistance. Finally, the best arrangement appears to have a layer of SIC impenetrable to anions in the polymer phase within the electrolyte membrane.

25 ENERGY STORAGE↗
DOE OSTI2021

Interconnected cathode-electrolyte double-layer enabling continuous Li-ion conduction throughout solid-state Li-S battery

All-solid-state lithium (Li) batteries with high energy density are a promising solution for the next-generation energy storage systems in large-scale devices. To simultaneously overcome the challenges of poor ionic conduction of solid electrolytes and shuttling of active materials, here we introduce a functional electrolyte-cathode bilayer framework with interconnected LLAZO channels from the electrolyte into the cathode for advanced solid-state Li-S batteries. Differing from the traditional solid-state batteries with separated layer compositions, the introduced bilayer framework provides ultrafast and continuous ion/electron conduction. Instead of transferring Li+ across the polymer and garnet phases which involve huge interfacial resistance, Li+ is directly conducted through the LLAZO channels created continuously from the cathode layer to the solid electrolyte layer, significantly shortening the diffusion distance and facilitating the redox reaction of sulfur and sulfides. A stable cycle life is demonstrated in the prototype Li-S solid-state batteries assembled with the introduced LLAZO-LLAZO@CNF interconnected bilayer framework. High capacity is obtained at room temperature, indicating the superior electrochemical properties of the bilayer framework that result from the unique design of the interconnected LLAZO garnet phase.

25 ENERGY STORAGE↗
DOE OSTI2021

Mathematical modeling of novel porous transport layer architectures for proton exchange membrane electrolysis cells

Thin foil based porous transport layers (PTLs) that contain highly structured pore arrays have shown promise as anode PTLs in proton exchange membrane electrolysis cells. These novel PTLs, fabricated with advanced manufacturing techniques, produce thin, tunable, multifunctional layers with reduced flow and interfacial resistances and high thermal and electric conductivities. To further optimize their design, it is important to understand their fundamental impact on the transport of protons, electrons, and liquid/vapor mixtures in the electrode. In this work, we develop a two-dimensional multiphysics model to simulate the coupled electrochemistry and multiphase transport in an electrolysis cell operated with the novel PTL architecture. The results show that larger pores improve access of water to the anode catalyst layer, which is beneficial for both the oxygen evolution reaction and membrane hydration. Larger pore sizes also improve oxygen gas transport from the catalyst layer, because generated oxygen gas is forced to travel in-plane through the anode catalyst layer until it reaches a pore opening that is connected to a channel. The discussed results confirm that the proposed thin foil based PTLs are fundamentally different from conventional PTLs, such as felts or layered meshes. The model developed in this work also provides generalizable insight into fundamental PEMEC phenomena, such as the competition between liquid and gas phase transport, membrane hydration and water management, and nonuniform electrochemical reactions, which are processes relevant to all PEMEC designs.

25 ENERGY STORAGE↗
DOE OSTI2020

Towards a high-performance garnet-based solid-state Li metal battery: A perspective on recent advances

Garnet-based solid-state Li metal batteries have been widely considered one of the most promising next-generation energy storage systems. However, the performance of these batteries is plagued by various limitations caused by the solid-state electrolyte (SSE). The poor wetting of lithium on the garnet surface diminishes the contact between the anode and electrolyte, leading to extremely high anode interfacial resistance. Similarly, the point-to-point contact between the cathode and electrolyte leads to high impedance on the cathode side. Moreover, although the SSE serves a firm barrier separating the anode and cathode, lithium dendrites can still grow through, causing a short circuit. Lastly, the solid/solid interface cannot be well maintained under cycling at high current density and capacity. Recently, remarkable progress has been achieved in garnet electrolyte to resolve these problems towards the aim of a high-performance solid-state Li metal battery. In this perspective, we highlight various recent advances in the field of garnet-based solid-state battery, including improving the anode/electrolyte interface, lithium dendrite detection, reducing cathode impedance, and electrolyte architecture design.

25 ENERGY STORAGE↗