SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Package includes installation, operation and maintenance manual for collector, analysis of safety hazards, special handling instructions, materials list, installation drawings, and warranty and certification statement. Manual includes instructions for roof preparation and for preparing collector for installation. Several pages are devoted to major and minor repairs.
The Solar 2 dimensions are four feet by eight feet by two and one half inches. The collector weighs 130 pounds and has an effective solar collection area of over 29.5 square feet. This area represents 95 percent of the total surface of the collector. The installation, operation and maintenance manual, safety hazard analysis, special handling instructions, materials list, installation concept drawings, warranty and certification statement are included in the installation package.
Information on the solar heating system installed at the Blakedale Professional Center, in Greenwood, South Carolina is presented. The information consists of site and building description, solar system description, performance evaluation, system problems and installation drawings. The solar system was designed to provide approximately 85 percent of the building's heating requirements. The system was installed concurrently with building construction and heats 4,440 square feet of the building. There are 954 square feet of liquid flat plate collectors that are proof-mounted and have a drain-down system to protect the collectors from freezing. A 5,000 gallon steel, polyurethane insulated tank buried underground provides storage. The system was fully instrumented for performance evaluation and integrated into the National Solar Data Network.
Solar water heating systems installed at Tempe, Arizona and San Diego, California are described. The systems consist of the following: collector, collector-tank water loop, solar tank, conventional tank, and controls. General guidelines which may be utilized in development of detailed installation plans and specifications are provided along with instruction on operation, maintenance, and installation of solar hot water systems.
Powerplant installations involve complex flows, strongly influenced by viscous effects and often with important aerodynamic interactions between the airframe and propulsion system. The introduction of vehicle propulsion concepts, and points of emphasis in aircraft and missile design requirements, provide an expanding range of aerodynamic problems which cal for both experimental and theoretical study. Aerodynamic problems in powerplant installation are surveyed and work which has improved basic understanding or has enhanced prediction and design methods in this field is reviewed. Powerplant installation effects for both combat and transport aircraft are emphasized.
The acoustical effects of operating a 6-cm exit-diameter nozzle in the presence of a wing-flap model under static conditions are examined experimentally. The geometric parameters of the wing-flap model are chosen to represent a realistic jet-engine installation on a wide-body midrange transport airplane. The effects of varying the installation parameters and the noise sources associated with the engine-installation effects are discussed. The major noise sources are the flow interaction of the jet and wing undersurface, the flow interaction of the jet with the side edges of the flap cutout and flap trailing edge, and the reflection of the jet noise off the undersurface of the wing and flap.
The paper provides an overview of the renewed interest in turboprop propulsion systems for future commercial transport designs. The potential operating cost advantage of advanced turbofan designs. Critical technology items for the aerodynamic installation of turboprop propulsion systems are presented, along with experimental results addressing the main technology issue for wing-mounted turboprop installations. Nacelle installation effects are presented for overwing and underwing nacelles. The drag reduction for nacelle contouring is also shown. Wing/nacelle/power data are presented for the baseline wing geometry and for a wing modified to reduce the propeller power effects.
A series of wind-tunnel investigations were conducted to determine the aerodynamic interference associated with the over wing and under wing installation of a turboprop nacelle on 20 deg swept and unswept supercritical wings. The purpose of the investigations was to increase the understanding of the flow interactions involved with the nacelle turboprop integration and to obtain experimental data for the verification of computational prediction techniques. The models were tested in the Langley 16-Foot Transonic Tunnel at Mach numbers from 0.50 to 0.80 and at angles-of-attack from 0 to 5 deg. In addition, data at several propeller pitch angles and advance ratio settings were obtained. This paper which presents only the results of the over-the-wing nacelle installations shows that wing sweep had considerable influence on the installation interference. Large scale flow separation was observed on the swept wing at M = 0.8. Less severe effects were observed at M = 0.7 on the swept wing and for both M = 0.7 and 0.8 on the unswept wing.
Powerplant installation losses for an advanced, high-speed, turboprop transport have been investigated in the Ames Research Center Transonic Wind Tunnels as a part of the NASA Advanced Turboprop Program (ATP). Force and pressure tests have been completed at Mach numbers from 0.6 to 0.82 on baseline and modified powered-model configurations to determine the magnitude of the losses and to what extent current design tools could be used to optimize the installed performance of turboprop propulsion systems designed to cruise at M = 0.8. Results of the tests indicate a large reduction in installed drag for the modified configuration. The wing-mounted power plant caused destabilizing pitching moments and a negative shift in the zero-lift pitching moment.
A preliminary feasibility assessment of the integration of reactor power system concepts with a projected growth space station architecture was conducted to address a variety of installation, operational disposition, and safety issues. A previous NASA sponsored study, which showed the advantages of space station - attached concepts, served as the basis for this study. A study methodology was defined and implemented to assess compatible combinations of reactor power installation concepts, disposal destinations, and propulsion methods. Three installation concepts that met a set of integration criteria were characterized from a configuration and operational viewpoint, with end-of-life disposal mass identified. Disposal destinations that met current aerospace nuclear safety criteria were identified and characterized from an operational and energy requirements viewpoint, with delta-V energy requirement as a key parameter. Chemical propulsion methods that met current and near-term application criteria were identified and payload mass and delta-V capabilities were characterized. These capabilities were matched against concept disposal mass and destination delta-V requirements to provide the feasibility of each combination.
To determine shuttle orbiter wing loads during ascent, wing load instrumentation was added to Columbia (OV-102). This instrumentation included strain gages and pressure orifices on the wing. The loads derived from wing pressure measurements taken during STS 61-C did not agree with those derived from strain gage measurements or with the loads predicted from the aerodynamic database. Anomalies in the surface immediately surrounding the pressure orifices in the thermal protection system (TPS) tiles were one possible cause of errors in the loads derived from wing pressure measurements. These surface anomalies were caused by a ceramic filler material which was installed around the pressure tubing. The filler material allowed slight movement of the TPS tile and pressure tube as the airframe flexed and bent under aerodynamic loads during ascent and descent. Postflight inspection revealed that this filler material had protruded from or receeded beneath the surface, causing the orifice to lose its flushness. Flight tests were conducted at NASA Ames Research Center Dryden Flight Research Facility to determine the effects of any anomaly in surface flushness of the orifice installation on the measured pressures at Mach numbers between 0.6 and 1.4. An F-104 aircraft with a flight test fixture mounted beneath the fuselage was used for these flights. Surface flushness anomalies typical of those on the orbiter after flight (STA 61-C) were tested. Also, cases with excessive protrusion and recession of the filler material were tested. This report shows that the anomalies in STS 61-C orifice installations adversely affected the pressure measurements. But the magnitude of the affect was not great enough to account for the discrepancies with the strain gage measurements and the aerodynamic predictions.
The design requirements for panel installation process are listed and photographs are presented of the following: panel latches to truss via adaptors; panel end effector; arm retrieving panel from canister; arm installing panel; and facility view with panel installed.
Gasturbine engine components as compressors, burners and turbines are usually tested on rigs prior to installation into an engine. In the engine, the component behaviour is different due to a variety of reasons. The installation effects are caused by small geometrical differences due to nonrepresentative rig operating temperatures and pressures, by different gas properties and Reynolds numbers and by radial as well as circumferential temperature and pressure profiles at the inlet to the component. For highly accurate performance predictions these rig-to-engine effects have to be taken into account. Traditionally the term "installation" is also used for describing all the differences in engine operation and behaviour between toothed and aircraft. Intake and afterbody drag, power offtake and bleed as well as intake pressure losses and inlet flow distortion have significant impact on airflow, thrust, specific fuel consumption and compressor stability. Using modem performance synthesis programs all these effects can be simulated reasonably well.
Two tools designed to be used together to drive long locking keys axially to install them on stud. Tools are: supporter holding keys in correct relative alignment and driver having multiple prongs, each of which fits into one of holes in supporter. Tools prevent bending and breaking of keys during installation, and make possible to install all keys simultaneously, in one motion.
Flight tests have been conducted to determine the repeatability of the over-all altimetry errors in the landing-approach condition of two sensitive altimeters (Air Force type C-12) installed in the cockpit of a transport airplane and of four precision altimeters (Air Force type MA-1) installed in a photo-observer. Data were obtained through a speed range of 62 to 100 knots during 42 landing-approach operations conducted on four different days. The results of the tests show that the repeatability errors of the two sensitive altimeters are +/- 35 feet and +/- 39 feet. These errors are of the same order as the maximum repeatability error measured in previous tests of eleven airplanes of the same type. For each of the four flights of the present tests the mean values of the data obtained with the two sensitive altimeters shifted by relatively large amounts, apparently because of the interaction of the stability and aftereffect- recovery characteristics of the instruments. For concurrent measurements of the over-all errors of the four precision altimeters, it is concluded that for comparable installations, the repeatability errors measured with these altimeters would be smaller than those measured with the sensitive altimeters.
Live footage of the Delta XTE (X-Ray Timing Explorer) fairing installation is presented. The fairing is installed to provide a smooth surface for the airflow. The primary purpose of the fairing is to reduce drag. The installation of the fairing occurred at complex 17-B CCAS (Cape Canaveral Air Station).
The recent developments in Fabry-Perot fiber optic instruments have resulted in accurate transducers with some of the physical characteristics required for use in obtaining internal data from solid rocket motors. These characteristics include small size, non-electrical excitation, and immunity to electro-magnetic interference. These transducers have not been previously utilized in this environment due to the high temperatures typically encountered. A series of tests were conducted using a 1 1-Inch Hybrid test bed to develop installation techniques that will allow the fiber optic instruments to survive and obtain data for a short period of time following the motor ignition. The installation methods developed during this test series have the potential to allow data to be acquired in the motor chamber, propellant bore, and nozzle during the ignition transient. These measurements would prove to be very useful in the characterization of current motor designs and provide insight into the requirements for further refinements. The process of developing these protective methods and the installation techniques used to apply them is summarized.
This paper describes progress made towards the installation of a hydrogen fueling station in Northeast Ohio. In collaboration with several entities in the Northeast Ohio area, the NASA Glenn Research Center is installing a hydrogen fueling station that uses electrolysis to generate hydrogen on-site. The installation of this station is scheduled for the spring of 2012 at the Greater Cleveland Regional Transit Authority s Hayden bus garage in East Cleveland. This will be the first electrolysis-based hydrogen fueling station in Ohio.