Results for “ice physics” — Page 4

NASA NTRS2006

Microwave Signatures of Snow on Sea Ice: Modeling

Accurate knowledge of snow-depth distribution over sea ice is critical for polar climate studies. Current snow-depth-over-sea-ice retrieval algorithms do not sufficiently account for variations in snow and ice physical properties that can affect the accuracy of retrievals. For this reason, airborne microwave observations were coordinated with ground-based measurements of snow depth and snow properties in the vicinity of Barrow, AK, in March 2003. In this paper, the effects of snowpack properties and ice conditions on microwave signatures are examined using detailed surface-based measurements and airborne observations in conjunction with a thermal microwave-emission model. A comparison of the Microwave Emission Model of Layered Snowpacks (MEMLS) simulations with detailed snowpack and ice data from stakes along the Elson Lagoon and the Beaufort Sea and ra- 'diometer data taken from low-level flights using a Polarimetric Scanning Radiometer (PSR-A) shows that MEMLS can be used to simulate snow on sea ice and is a useful tool for understanding the limitations of the snow-depth algorithm. Analysis of radiance data taken over the Elson Lagoon and the Beaufort Sea using MEMLS suggests that the radiometric differences between the two locations are due to the differences in sea-ice emissivity. Furthermore, measured brightness temperatures suggest that the current snow-depth retrieval algorithm is sufficient for areas of smooth first-year sea ice, whereas new algorithm coefficients are needed for rough first-year sea ice. Snowpack grain size and density remain an unresolved issue for snow-depth retrievals using passive-microwave radiances.

Powell, D. C.↗

NASA NTRS1986

Experimental evidence for modifying the current physical model for ice accretion on aircraft surfaces

Closeup movies, still photographs, and other experimental data suggest that the current physical model for ice accretion needs significant modification. At aircraft airspeeds there was no flow of liquid over the surface of the ice after a short initial flow, even at barely subfreezing temperatures. Instead, there were very large stationary drops on the ice surface that lose water from their bottoms by freezing and replenish their liquid by catching the microscopic cloud droplets. This observation disagrees with the existing physical model, which assumes there is a thin liquid film continuously flowing over the ice surface. With no such flow, the freezing-fraction concept of the model fails when a mass balance is performed on the surface water. Rime ice does, as the model predicts, form when the air temperature is low enough to cause the cloud droplets to freeze almost immediately on impact. However, the characteristic shapes of horn-glaze ice or rime ice are primarily caused by the ice shape affecting the airflow locally and consequently the droplet catch and the resulting ice shape. Ice roughness greatly increases the heat transfer coefficient, stops the movement of drops along the surface, and may also affect the airflow initially and thereby the droplet catch. At high subreezing temperatures the initial flow and shedding of surface drops have a large effect on the ice shape. At the incipient freezing limit, no ice forms.

Olsen, W.↗

NASA NTRS2009

NASA Iced Aerodynamics and Controls Current Research

This slide presentation reviews the state of current research in the area of aerodynamics and aircraft control with ice conditions by the Aviation Safety Program, part of the Integrated Resilient Aircraft Controls Project (IRAC). Included in the presentation is a overview of the modeling efforts. The objective of the modeling is to develop experimental and computational methods to model and predict aircraft response during adverse flight conditions, including icing. The Aircraft icing modeling efforts includes the Ice-Contaminated Aerodynamics Modeling, which examines the effects of ice contamination on aircraft aerodynamics, and CFD modeling of ice-contaminated aircraft aerodynamics, and Advanced Ice Accretion Process Modeling which examines the physics of ice accretion, and works on computational modeling of ice accretions. The IRAC testbed, a Generic Transport Model (GTM) and its use in the investigation of the effects of icing on its aerodynamics is also reviewed. This has led to a more thorough understanding and models, both theoretical and empirical of icing physics and ice accretion for airframes, advanced 3D ice accretion prediction codes, CFD methods for iced aerodynamics and better understanding of aircraft iced aerodynamics and its effects on control surface effectiveness.

Addy, Gene↗

NASA NTRS2024

GlennICE Manual 4.1.0

GlennICE (Glenn Icing Computational Environment) is a computational tool designed to calculate ice growth on complex three-dimensional geometries using the input from a user-supplied computational fluid dynamics (CFD) solution for the geometry of interest. The NASA John H. Glenn Research Center at Lewis Field is developing this tool to aid those evaluating, designing and certifying aircraft, engines, and aircraft components for flight in icing conditions. This domestically available software is being developed to enable the introduction of new icing physics into a computational environment in a manner that is open for evaluation and eventual use by industry, academia, and other government organizations.

Icing↗

NASA NTRSDate not supplied

Cloud Uniformity Measurement from NASA's 2nd Fundamental Ice Crystal Icing Test - Part 2 (Temperature and Humidity)

This paper provides a characterization of the temperature and humidity variations within icing cloud flows generated during the second Fundamental Ice Crystal Icing Physics test conducted in NASA’s Propulsion Systems Laboratory, in June of 2018. The tests were conducted at airflow velocities of 85, 135, and 185 m/s, a static pressure of 44.8 kPa, and a total temperature of 7.2 ⁰C. A custom rearward facing probe and commercial total air temperature probe were used to obtain temperature and humidity profiles of the icing cloud flow leaving the exit duct plane. Additional background humidity measurements were also obtained from a commercial total water content probe. The probes captured the changes in temperature and humidity that took place at the test section after the cloud was activated. As the main altitude airflow interacts with the icing cloud, their thermodynamic properties undergo substantial changes. Due to the particle nature of the icing cloud, the droplets and ice crystals tend to redistribute within the cloud as it propagates with the main flow. Data will be presented that shows how these factors affect the thermodynamic property distribution within the icing cloud. A discussion is given of the thermal balances in the icing cloud, between the evaporating spray droplets and the airflow, as a basis for interpreting the measured results.

Crystal Icing↗

NASA NTRSDate not supplied

GlennICE 2.2 Capabilities and Results

GlennICE (Glenn Icing Computational Environment) is a computational tool designed to calculate ice growth on complex three-dimensional geometries using the input from a user-supplied computational fluid dynamics (CFD) solution for the geometry of interest. The NASA John H. Glenn Research Center at Lewis Field is developing this tool to aid those evaluating, designing and certifying aircraft, engines, and aircraft components for flight in icing conditions. This domestically available software is being developed to enable the introduction of new icing physics into a computational environment in a manner that is open for evaluation and eventual use by industry, academia, and other government organizations. This paper will document the current capabilities for version 2.1 of this software and provide example cases with comparison to available experimental data.

Icing↗

NASA NTRSDate not supplied

Improvements to GlennICE Collection Efficiency Algorithm

GlennICE (Glenn Icing Computational Environment) is a computational tool designed to calculate ice growth on complex three-dimensional geometries using the input from a user-supplied computational fluid dynamics (CFD) solution for the geometry of interest. The NASA John H. Glenn Research Center at Lewis Field is developing this tool to aid those evaluating, designing and certifying aircraft, engines, and aircraft components for flight in icing conditions. This domestically available software is being developed to enable the introduction of new icing physics into a computational environment in a manner that is open for evaluation and eventual use by industry, academia, and other government organizations. This paper will document recent improvements that reduce the number of trajectories needed to converge on collection efficiency. These improvements are documented using example cases with complex geometries.

Aircraft Icing↗

NASA NTRSDate not supplied

Improvements to GlennICE Collection Efficiency Algorithm

GlennICE (Glenn Icing Computational Environment) is a computational tool designed to calculate ice growth on complex three-dimensional geometries using the input from a user-supplied computational fluid dynamics (CFD) solution for the geometry of interest. The NASA John H. Glenn Research Center at Lewis Field is developing this tool to aid those evaluating, designing and certifying aircraft, engines, and aircraft components for flight in icing conditions. This domestically available software is being developed to enable the introduction of new icing physics into a computational environment in a manner that is open for evaluation and eventual use by industry, academia, and other government organizations. This paper will document recent improvements that reduce the number of trajectories needed to converge on collection efficiency. These improvements are documented using example cases with complex geometries.

Aircraft Icing↗

NASA NTRSDate not supplied

GlennICE 2.2 Capabilities and Results

GlennICE (Glenn Icing Computational Environment) is a computational tool designed to calculate ice growth on complex three-dimensional geometries using the input from a user-supplied computational fluid dynamics (CFD) solution for the geometry of interest. The NASA John H. Glenn Research Center at Lewis Field is developing this tool to aid those evaluating, designing and certifying aircraft, engines, and aircraft components for flight in icing conditions. This domestically available software is being developed to enable the introduction of new icing physics into a computational environment in a manner that is open for evaluation and eventual use by industry, academia, and other government organizations. This paper will document the current capabilities for version 2.1 of this software and provide example cases with comparison to available experimental data.

Icing↗

NASA NTRS2011

Fundamental Ice Crystal Accretion Physics Studies

Due to numerous engine power-loss events associated with high-altitude convective weather, ice accretion within an engine due to ice-crystal ingestion is being investigated. The National Aeronautics and Space Administration (NASA) and the National Research Council (NRC) of Canada are starting to examine the physical mechanisms of ice accretion on surfaces exposed to ice-crystal and mixed-phase conditions. In November 2010, two weeks of testing occurred at the NRC Research Altitude Facility utilizing a single wedge-type airfoil designed to facilitate fundamental studies while retaining critical features of a compressor stator blade or guide vane. The airfoil was placed in the NRC cascade wind tunnel for both aerodynamic and icing tests. Aerodynamic testing showed excellent agreement compared with CFD data on the icing pressure surface and allowed calculation of heat transfer coefficients at various airfoil locations. Icing tests were performed at Mach numbers of 0.2 to 0.3, total pressures from 93 to 45 kPa, and total temperatures from 5 to 15 C. Ice and liquid water contents ranged up to 20 and 3 grams per cubic meter, respectively. The ice appeared well adhered to the surface in the lowest pressure tests (45 kPa) and, in a particular case, showed continuous leading-edge ice growth to a thickness greater than 15 millimeters in 3 minutes. Such widespread deposits were not observed in the highest pressure tests, where the accretions were limited to a small area around the leading edge. The suction surface was typically ice-free in the tests at high pressure, but not at low pressure. The icing behavior at high and low pressure appeared to be correlated with the wet-bulb temperature, which was estimated to be above 0 C in tests at 93 kPa and below 0 C in tests at lower pressure, the latter enhanced by more evaporative cooling of water. The authors believe that the large ice accretions observed in the low pressure tests would undoubtedly cause the aerodynamic performance of a compressor component such as a stator blade to degrade significantly, and could damage downstream components if shed.

Currie, Tom↗

NASA NTRS2012

Fundamental Ice Crystal Accretion Physics Studies

Due to numerous engine power-loss events associated with high-altitude convective weather, ice accretion within an engine due to ice crystal ingestion is being investigated. The National Aeronautics and Space Administration (NASA) and the National Research Council (NRC) of Canada are starting to examine the physical mechanisms of ice accretion on surfaces exposed to ice-crystal and mixed-phase conditions. In November 2010, two weeks of testing occurred at the NRC Research Altitude Facility utilizing a single wedge-type airfoil designed to facilitate fundamental studies while retaining critical features of a compressor stator blade or guide vane. The airfoil was placed in the NRC cascade wind tunnel for both aerodynamic and icing tests. Aerodynamic testing showed excellent agreement compared with CFD data on the icing pressure surface and allowed calculation of heat transfer coefficients at various airfoil locations. Icing tests were performed at Mach numbers of 0.2 to 0.3, total pressures from 93 to 45 kPa, and total temperatures from 5 to 15 C. Ice and liquid water contents ranged up to 20 and 3 g/m3, respectively. The ice appeared well adhered to the surface in the lowest pressure tests (45 kPa) and, in a particular case, showed continuous leading-edge ice growth to a thickness greater than 15 mm in 3 min. Such widespread deposits were not observed in the highest pressure tests, where the accretions were limited to a small area around the leading edge. The suction surface was typically ice-free in the tests at high pressure, but not at low pressure. The icing behavior at high and low pressure appeared to be correlated with the wet-bulb temperature, which was estimated to be above 0 C in tests at 93 kPa and below 0 C in tests at lower pressure, the latter enhanced by more evaporative cooling of water. The authors believe that the large ice accretions observed in the low pressure tests would undoubtedly cause the aerodynamic performance of a compressor component such as a stator blade to degrade significantly, and could damage downstream components if shed.

Struk, Peter M.↗

NASA NTRS2014

The DMRT-ML Model: Numerical Simulations of the Microwave Emission of Snowpacks Based on the Dense Media Radiative Transfer Theory

Microwave radiometer observations have been used to retrieve snow depth and snow water equivalent on both land and sea ice, snow accumulation on ice sheets, melt events, snow temperature, and snow grain size. Modeling the microwave emission from snow and ice physical properties is crucial to improve the quality of these retrievals. It also is crucial to improve our understanding of the radiative transfer processes within the snow cover, and the snow properties most relevant in microwave remote sensing. Our objective is to present a recent microwave emission model and its validation. The model is named DMRT-ML (DMRT Multi-Layer).

Microwave radiometer↗

NASA NTRS1999

An Optimal Relation of Radar Reflectivity to Lightning Rate

Thunderstorms separate charge. Most places they lift positive charge or lower negative, a few places they lift negative or lower positive. The electrical generator is stronger in some parts of the cloud than in others. Our long term goal is to map this generator. Cloud physicists tell us that uncharged ice and water particles become charged by collision, and that the charge transferred depends on size, temperature and humidity. There is still some disagreement about exactly how the charge transferred depends on size, temperature, and humidity. In principle, if we knew this ice physics, and also knew the distribution of particles everywhere in the storm, and the winds everywhere and the temperature and humidity everywhere, then we could compute everywhere the electrical power of the thunderstorm generator. In practice it is difficult to know all these things, particularly the distribution of particles, so it is difficult to use real thunderstorms to falsify cloud electrification theories. We here take one small step towards computing that map of electrical generator power, by relating radar reflectivity profiles of 2000 storms to lightning flash rates of those storms. This small step by itself doesn't falsify any existing electrification theories; it merely places weak constraints on the relation of electric generator power to cloud ice.

Heckman, S.↗

NASA NTRS2014

The DMRT-ML Model: Numerical Simulations of the Microwave Emission of Snowpacks Based on the Dense Media Radiative Transfer Theory

Microwave radiometer observations have been used to retrieve snow depth and snow water equivalent on both land and sea ice, snow accumulation on ice sheets, melt events, snow temperature, and snow grain size. Modeling the microwave emission from snow and ice physical properties is crucial to improve the quality of these retrievals. It also is crucial to improve our understanding of the radiative transfer processes within the snow cover, and the snow properties most relevant in microwave remote sensing. Our objective is to present a recent microwave emission model and its validation. The model is named DMRT-ML (DMRT Multi-Layer), and is available at http:lgge.osug.frpicarddmrtml.

ice sheet↗

DOE OSTI2026

The Energy Exascale Earth System Model Version 3: 2. Overview of the Coupled System

The Energy Exascale Earth System Model version 3 (E3SMv3) represents the latest advancement in Earth system modeling developed by the U.S. Department of Energy (DOE). Building upon previous versions, E3SMv3 introduces significant updates across its coupled components to enhance capability and improve fidelity. The atmosphere component incorporates advancements in chemistry, aerosol-cloud interactions, convection, and microphysics. The ocean features a new time-stepping scheme and a higher-resolution unstructured mesh with sub-ice-shelf cavities, while the sea ice model integrates advanced snow and ice physics for more realistic cryospheric simulations. The land model introduces prognostic vegetation dynamics and a new sub-grid topographic treatment of solar radiation. A new tri-grid configuration harmonizes the horizontal grids of the land and river components for improved process coupling. It is enabled by a new non-linear remapping between the atmosphere and land. E3SMv3 underwent extensive testing through a comprehensive simulation campaign, including pre-industrial control, idealized CO 2 experiments, and historical simulations spanning 1850–2024. The model demonstrates significant improvements in simulating the evolution of the historical surface temperature, particularly addressing the “pothole cooling” bias in earlier versions. Reduced aerosol-related forcing contributes to more realistic radiative forcing and better alignment with the observational record. Ocean heat content (OHC) and sea ice trends are also improved as a result.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRSDate not supplied

Effect of Water Droplets Crossing the Boundary Layer in a Stagnation Point Configuration

An experimental study was conducted in the Vertical Icing Studies Tunnel at the Icing Physics Flow Laboratory of NASA Glenn Research Center to study the effect of water droplets crossing the boundary layer in a stagnation point configuration. The objective of the experiment was to determine if water droplets crossing a boundary layer create turbulent spots that accelerate the boundary layer transition from laminar to turbulent. Water droplets that crossed the boundary layer were generated with a nozzle installed in the plenum. The turbulence level in the boundary layer was measured with a hot wire system when the nozzle was off, air on, and air and water on. The results indicate that the presence of the nozzle alone did not affect the boundary layer. The activation of the nozzle to eject air only or to generate water droplets affected the turbulence level in the boundary layer. The continued study of this effect is needed because of its implications in the development of heat transfer models for icing codes.

Icing↗

DOE OSTI2022

Simulating ice-shelf extent using damage mechanics

Abstract Inaccurate representations of iceberg calving from ice shelves are a large source of uncertainty in mass-loss projections from the Antarctic ice sheet. Here, we address this limitation by implementing and testing a continuum damage-mechanics model in a continental scale ice-sheet model. The damage-mechanics formulation, based on a linear stability analysis and subsequent long-wavelength approximation of crevasses that evolve in a viscous medium, links damage evolution to climate forcing and the large-scale stresses within an ice shelf. We incorporate this model into the BISICLES ice-sheet model and test it by applying it to idealized (1) ice tongues, for which we present analytical solutions and (2) buttressed ice-shelf geometries. Our simulations show that the model reproduces the large disparity in lengths of ice shelves with geometries and melt rates broadly similar to those of four Antarctic ice shelves: Erebus Glacier Tongue (length ~ 13 km), the unembayed portion of Drygalski Ice Tongue (~ 65 km), the Amery Ice Shelf (~ 350 km) and the Ross Ice Shelf (~ 500 km). These results demonstrate that our simple continuum model holds promise for constraining realistic ice-shelf extents in large-scale ice-sheet models in a computationally tractable manner.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

The GFDL‐CM4X Climate Model Hierarchy, Part I: Model Description and Thermal Properties

We present the GFDL‐CM4X (Geophysical Fluid Dynamics Laboratory Climate Model version 4X) coupled climate model hierarchy. The primary application for CM4X is to investigate ocean and sea ice physics as part of a realistic coupled Earth climate model. CM4X utilizes an updated MOM6 (Modular Ocean Model version 6) ocean physics package relative to CM4.0, and there are two members of the hierarchy: one that uses a horizontal grid spacing of 0.25° (referred to as CM4X‐p25) and the other that uses a grid 0.125° (CM4X‐p125). CM4X also refines its atmospheric grid from the nominally 100 km (cubed sphere C96) of CM4.0–50 km (C192). Finally, CM4X simplifies the land model to allow for a more focused study of the role of ocean changes to global mean climate. CM4X‐p125 reaches a global ocean area mean heat flux imbalance of -0.02 W m -2 within $\mathcal{O}$ (150) years in a pre‐industrial simulation, and retains that thermally equilibrated state over the subsequent centuries. This 1850 thermal equilibrium is characterized by roughly 400 ZJ less ocean heat than present‐day, which corresponds to estimates for anthropogenic ocean heat uptake between 1870 and present‐day. CM4X‐p25 approaches its thermal equilibrium only after more than 1000 years, at which time its ocean has roughly 1100 ZJ more heat than its early 21st century ocean initial state. Furthermore, the root‐mean‐square sea surface temperature bias for historical simulations is roughly 20% smaller in CM4X‐p125 relative to CM4X‐p25 (and CM4.0). We offer the mesoscale dominance hypothesis for why CM4X‐p125 shows such favorable thermal equilibration properties.

54 ENVIRONMENTAL SCIENCES↗