SEARCH · Engineering Papers

Results for “high-pressure engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

DOE OSTI2025

2D CFD of lean premixed hydrogen–air flame quenching under locomotive engine conditions

Hydrogen (H 2 ) is a promising fuel for reducing emissions in heavy-duty internal combustion engines (ICEs), but its low quenching distance increases the risk of flame propagation into narrow crevice regions, such as piston-liner gaps. This work uses detailed CFD simulations with finite-rate chemistry to investigate premixed H 2 –air flame quenching in a two-dimensional (2D) region consistent with the piston-liner gap of a diesel ICE. Model accuracy was assessed by comparison with experimentally measured quenching distances in an annular stepwise diverging tube (ASDT). A parametric study was conducted to assess the influence of crevice width (0.05–1.18 mm), pressure (50–150 bar), unburned gas temperature (431–573 K), and equivalence ratio ( Φ= 0.3–0.6). Results show that the critical Péclet number for flame survival is no greater than 3.25, consistent with prior literature, even under ultra-lean and high-pressure conditions (Φ ≤ 0.3, > 50 bar). Additionally, flames with Péclet numbers exceeding 6.15 exhibited front wrinkling, suggesting the onset of velocity-driven instabilities and enhanced flame robustness. These findings help define thresholds for flame quenching in confined geometries and support the safe design of H 2 fueled ICEs.

08 HYDROGEN↗

DOE OSTI2026

High pressure effects on EBC systems in high temperature environments

Environmental barrier coatings (EBCs) are designed to protect SiCfiber/SiCmatrix ceramic matrix composites (CMCs) in turbine engines by mitigating wear in high-temperature water vapor environments. The failure of EBCs is frequently attributed to the accelerated oxidation of the silicon bond coating layer when exposed to high-temperature steam, leading to the formation of a thickened thermally grown oxide (TGO). TGO growth increases interfacial stress, weakens adhesion, and results in coating spallation. Understanding the impact of high-temperature oxidation of EBC systems is essential for developing accurate lifespan models for turbine components, although pressurized oxidation testing is extremely sparse in the open literature. In this work, oxidation tests were performed on rare earth silicate EBCs coated onto SiC substrates under increased pressure conditions. The coated specimens were tested at 1100°C, 1200°C, and 1300°C at both 1 atm and 10 atm total pressure in steam environments. Subsequent characterization focused on the microstructural evolution of the EBC/Si/SiC system. The experimental findings indicated that TGO behavior is dependent on high-pressure conditions, with elevated pressure leading to an increase in oxide scale thickness and modifications in its morphology.

Ardrey, Kristyn [ORNL] (ORCID:0000000184407796)↗

DOE OSTI2025

Advanced nuclear reactor integration opportunities for the pulp and paper industry in the U.S. context: Technical perspectives, gap analysis, and preliminary technoeconomic assessment

Pulp and paper (P&P) manufacturing requires a large amount of low-pressure (LP) steam to digest, wash wood fibers and dry pulp into paper. Most of the LP steam is extracted from backpressure turbines that produce power from high-pressure (HP) steam. This HP steam is generated from burning wood waste material; bark is burned in hog boilers, and lignin is boiled in a black liquor recovery boiler. In a typical integrated P&P mill, 50–100% of the steam is produced from these sources, while additional steam is produced in natural gas (NG), fuel oil, or coal boilers. The other energy-intensive process in the plant is the chemical-recovery section (e.g., lime kiln), which requires high-temperature processing from NG combustion to retrieve and recirculate spent chemicals. This paper assesses the energy and heat demand and material balances of a typical generic kraft pulp mill, along with the nuclear heat, steam, and power integration opportunities to replace conventional combustion systems. The paper also addresses steam and electricity generation through a comprehensive technical and engineering gap analysis of five different nuclear-integration opportunities and their process economics, thus enabling the lignin and bark to be further processed into biobased chemicals or fuels, as well as the potential to reduce overall emissions from kraft pulping. Preliminary findings have shown that the P&P industry could achieve technological benefits by integrating their current manufacturing process with small modular nuclear reactors (SMNRs) on a national level. This research aims to set the path forward for a cleaner and more resilient P&P industry.

Advanced nuclear reactor↗

DOE OSTI2025

Ultrahigh pressure compaction-resistant thin film crosslinked composite reverse osmosis membranes

In this study, we present a class of thin-film crosslinked (TFX) composite reverse osmosis (RO) membranes that resist physical compaction at ultrahigh pressures (up to 200 bar). Since RO membranes experience compaction at virtually all pressure ranges, the ability to resist compaction has widespread implications for RO membrane technology. The process described herein involves crosslinking a phase inverted porous polyimide (PI) support membrane followed by interfacial polymerization of a polyamide layer, thereby forming a fully thermoset composite membrane structure. We explore a range of phase inversion membrane formation parameters such as PI concentration, solvent-cosolvent ratios, coagulation bath composition, and crosslinking methods in addition to interfacial polymerization reaction chemistry and conditions. Overall, TFX membranes exhibit significantly less compaction compared to hand-cast and commercial high-pressure RO membranes, experiencing less than 10% decline in water permeance and maintaining salt rejection over 99% for NaCl solutions up to 180,000 mg/L with 200 bar applied pressure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Background-Oriented Schlieren Velocimetry of Helium Coolant Flow in Additively Manufactured Channels

High-pressure helium gas cooling is an attractive solution for thermal management of the fusion blanket first wall, as this coolant is chemically and neutronically inert and separable from hydrogenic species. However, due to the low thermal mass of helium, geometric optimization of these channels is required to provide sufficient cooling at manageable flow rates and pumping burdens. Increasingly, analysis and optimization of these coolant channels rely on computational fluid dynamics (CFD) simulations, and these require relevant experimental data for turbulence model validation. Toward this end, a high-pressure helium gas flow visualization system has been employed to image the flow of helium in flow channels with one-sided heating, mimicking the blanket first wall environment. Flow of helium at 4 MPa pressure and flow rates up to 68 g/s (Reynolds number 57 000) is supplied to rectangular channel test sections, with uniform heating applied to the bottom wall of the channel at heat fluxes varied between roughly 50 and 130 kW/m2. A high-speed camera is used to image index of refraction (IOR) gradients in the fluid via background-oriented schlieren (BOS), and temperature and pressure instrumentation are used to characterize thermal-hydraulic performance of each channel. Cross correlation of time-resolved BOS images is then used to calculate time-averaged 2-D helium velocity fields. Flow in additively manufactured (AM) channels is examined in this manner, including both featureless channels and those containing baffling as a heat transfer enhancement. The flow distribution seen in the featureless case differs significantly from that seen in prior simulations, whereas the flow in the baffled case shows the predicted behavior of flow forced along the heated wall. This augmented flow distribution is seen to increase the heat transfer coefficient in the baffled test section. Here, strategies are discussed for ongoing and future validation of these simulations, with the aim of model deployment for blanket cooling design and optimization.

Additive manufacturing↗

DOE OSTI2025

High Pressure Hydrogen Nozzle Assembly and Dispenser for Heavy Duty Vehicles (Final Technical Report)

Electricore, Inc. along with partners Bennett Pump Company (Bennett), WEH Technologies, Inc. (WEH), National Renewable Energy Laboratory (NREL), and Quong & Associates, Inc. (QAI) have developed a high-pressure hydrogen nozzle assembly and dispenser for heavy-duty (HD) vehicles. The system was installed, tested and demonstrated at NREL’s Hydrogen Infrastructure Testing and Research Facility (HITRF). The system was designed to have a maximum operating pressure of 87.5 MPa and an approximate average flow rate of 10 kg/min over 10 minutes at fuel temperatures of -40°C. To further develop the specifications and design of the system, the team performed an industry survey to ensure the system met the needs of potential users.

08 HYDROGEN↗

DOE OSTI2025

Gas Hydrate Film Growth in Microfluidic Channels for Carbon Dioxide Capture and Sequestration Applications

Gas or clathrate hydrates are a solid, crystalline compound composed of water and guest molecules that typically form at high pressure and low temperature conditions. Carbon dioxide (CO2) hydrates may be involved in several carbon dioxide capture and sequestration (CCS) applications, including CO2 pipeline transportation and CO2 offshore sequestration. Within these applications, the formation mechanism and kinetics must be well understood to manage the CCS processes, either by preventing or promoting hydrate formation. In this work, a high-pressure glass microfluidic reactor is used in tandem with visual microscopy and in-situ Raman spectroscopy to study both the morphological and kinetic behavior of gas hydrate crystals. Subcooling, pressure, and CO2 flow rate are investigated for their impact on the thickening behavior of pure CO2 hydrates, with flow rate being the only parameter to have a significant effect. Visual and Raman spectroscopy evidence show that both a dense hydrate layer and a porous hydrate layer form, and the latter may provide a path for mass transfer to continue hydrate crystallization. A first principles mass transfer model is developed to describe CO2 hydrate crystal thickening at the interface between gas and water. The impacts of gas impurities and channel wettability are also studied. This method is further applied to investigate the conversion of methane hydrate to CO2 hydrate for combined energy recovery and methane hydrate formation. The authors acknowledge the US Department of Energy Basic Energy Science award # DE-SC0022162.

Wadsworth, Lindsey [Colorado School of Mines, Gold↗

DOE OSTI2025

DME-Propane Blends Ignition Experiments and Modeling for Heavy-Duty Mixing Controlled Compression Engines

A blend of dimethyl ether (DME) and propane (C3H8) is being studied in a shock tube at heavy-duty engine conditions at 110 bar. Due to its intrinsic combustion properties, DME/propane blend can potentially replace diesel in mixing controlled compression ignition engines. A blend of DME/propane can reduce emissions in mixing controlled compression ignition in heavy-duty engines through modifications, which require simulations using a high-fidelity chemical kinetics model that can accurately predict the chemistry of the blend. An essential aspect of testing the chemical kinetics model is doing baseline fundamental chemistry studies on neat DME and propane, which include ignition delay time measurements. In this work, using a high-pressure shock tube, ignition delay times were gathered for DME/Propane blends at 110 bar diluted with AR to test chemical kinetic models published in the literature. These models include Aramco 3.0, NUIG V1.1, C3mech V3.3, and Dames et al. Comparisons with the experimental IDTs and models were conducted, and general agreement was observed. A sensitivity analysis was conducted, and important reactions were outlined.

Mohammed, Zuhayr Pasha [University of Central Flor↗

DOE OSTI2025

Mechanical and Tribological Performance of Additively Manufactured Nanocrystalline Aluminum via Cryomilling and Cold Spray

In this study, nanocrystalline (NC) aluminum (Al) and magnesium (Mg)-doped Al bulk components were fabricated using a hybrid manufacturing process that combines cryomilling and high-pressure cold spray (HPCS) additive deposition techniques. Yttria-stabilized zirconia (YSZ) was also added during the HPCS process to improve deposition efficiency and build-up thickness via peening. The evolution of morphology, crystallite size, and elemental composition of both cryomilled powders and cold-sprayed (CS’ed) components was systematically characterized using X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM). Mechanical characterization was performed using Vickers microhardness and uniaxial tensile testing, while the tribological behavior was assessed using sliding wear tests under dry/lubricated conditions. XRD analysis revealed that increased cryomilling duration led to significant crystallite refinement, which directly correlated with enhanced hardness and strength. This mechanical strengthening was accompanied by an increase in coefficient of friction (COF) and lower wear rates. The results also showed that the Mg-doped Al exhibited superior hardness, tensile strength, and tribological performance compared to pure Al. The study further explores the underlying mechanisms responsible for these enhancements, highlighting the potential of solute-assisted grain boundary stabilization in tailoring high-performance NC Al alloys.

36 MATERIALS SCIENCE↗

NASA NTRS1971

Integral lift engine preliminary design

A preliminary mechanical design of a complete lift fan engine system is reported. A description of the lift fan engine, layout drawings of the components and complete engine, and a discussion of the design analyses and results are presented. The design features and areas of analysis include fan and compressor rotor blades of composite construction, a combustor folded over the compressor, relatively high-temperature blades in the high-pressure turbine, the first stage of the low-pressure turbine used for bearing support and ducting of lubricant to the bearings, a complete lubrication system, critical speeds of the shafting, and vibration and flutter of the blading.

Pratt, W.↗

NASA NTRS1973

Experimental evaluation of a TF30-P-3 turbofan engine in an altitude facility: Effect of steady-state temperature distortion

The effects of circumferential distortion of the total temperature entering 25, 50, and 75 percent of the inlet circumferential annulus of a turbofan engine were determined. Complete compressor stall resulted from distortions of from 14 to 20 percent of the face averaged temperature. Increasing the temperature level in one sector resulted in that sector moving toward stall by decreasing the equivalent rotor speeds while the pressure ratio remained approximately constant. Stall originated as a rotating zone in the low-pressure compressor which resulted as a terminal stall in the high-pressure compressor. Decreasing the Reynolds number index to 0.25 from 0.5 reduced the required distortion for stall by 50 percent for the conditions investigated.

Braithwaite, W. M.↗

NASA NTRS1973

Development of helicopter engine seals

An experimental evaluation of main shaft seals for helicopter gas turbine engines was conducted with shaft speeds to 213 m/s(700 ft/sec), air pressures to 148 N/sq cm (215 psia), and air temperatures to 645 K (675 F). Gas leakage test results indicate that conventional seals will not be satisfactory for high-pressure sealing because of excessive leakage. The self-acting face seal, however, had significantly lower leakage and operated with insignificant wear during a 150-hour endurance test at sliding speeds to 145 m/s (475 ft/sec), air pressures to 124 N/sq cm (180 psia), and air temperatures to 408 K (275 F). Wear measurements indicate that noncontact operation was achieved at shaft speeds of 43,000 rpm. Evaluation of the self-acting circumferential seal was inconclusive because of seal dimensional variations.

Lynwander, P.↗

NASA NTRS1975

A preliminary systems-engineering study of an advanced nuclear-electrolytic hydrogen-production facility

An advanced nuclear-electrolytic hydrogen-production facility concept was synthesized at a conceptual level with the objective of minimizing estimated hydrogen-production costs. The concept is a closely-integrated, fully-dedicated (only hydrogen energy is produced) system whose components and subsystems are predicted on ''1985 technology.'' The principal components are: (1) a high-temperature gas-cooled reactor (HTGR) operating a helium-Brayton/ammonia-Rankine binary cycle with a helium reactor-core exit temperature of 980 C, (2) acyclic d-c generators, (3) high-pressure, high-current-density electrolyzers based on solid-polymer electrolyte technology. Based on an assumed 3,000 MWt HTGR the facility is capable of producing 8.7 million std cu m/day of hydrogen at pipeline conditions, 6,900 kPa. Coproduct oxygen is also available at pipeline conditions at one-half this volume. It has further been shown that the incorporation of advanced technology provides an overall efficiency of about 43 percent, as compared with 25 percent for a contemporary nuclear-electric plant powering close-coupled contemporary industrial electrolyzers.

Escher, W. J. D.↗

NASA NTRS1976

The development of large diameter, high pressure, cryogenic radial static seals

Two configurations of radial static seals are developed for high-pressure 773 kg per sq cm cryogenic applications: a U-shaped fluorocarbon seal and a delta-shaped PTFE seal. The U-seal is a common commercial design consisting of a spring-loaded cup-shaped jacket; the basic principle is that the soft plastic jacket provides the interface between the piston and the bore, the jacket being held in place by a metal spring. The delta seal is based on the principle that the soft plastic delta cross section furnishes the interface at the metal face and circumferential face of the gland and cylinder. Test results indicate that both the plastic U-seal and the delta seal designs are sufficiently flexible to accommodate assembly in bore or piston grooves. Of these two configurations, the delta seal is found to be superior as it meets all the design requirements for proof pressure testing the turbopump components of the main engine in the Space Shuttle.

Burr, M. E.↗

NASA NTRS1976

A high-pressure, high-temperature combustor and turbine-cooling test facility

NASA-Lewis Research Center is presently constructing a new test facility for developing turbine-cooling and combustor technology for future generation aircraft gas turbine engines. Prototype engine hardware will be investigated in this new facility at gas stream conditions up to 2480 K average turbine inlet temperature and 4,140,000 N per sq m turbine inlet pressure. The facility will have the unique feature of fully-automated control and data acquisition through the use of an integrated system of minicomputers and programmable controllers, which will result in more effective use of operating time, will limit the number of operators required, and will provide a built-in self-protection safety system. The paper describes the facility and the planning and design considerations involved.

Cochran, R. P.↗

NASA NTRS1970

Electroplating offers embrittlement protection

Thin copper electrodeposited layer protects metal parts in environments with which they may be incompatible. Originally developed for main engine of Space Shuttle where high strength nickle alloy bellows must operate in high-pressure hydrogen, technique protects nickel and is unaffected by forming process or subsequent heat treatment and preinstallation processing.

Daniels, C. M., Jr.↗

NASA NTRS1938

The N.A.C.A. Optical Engine Indicator

An optically recording engine-pressure indicator of simple and rugged construction has been developed for use in high-pressure and high temperature combustion research. This instrument is of the diaphragm type and has a natural frequency of about 10,000 cycles per second.

Tozier, Robert E↗

NASA NTRS1931

Pressure Fluctuations in a Common-Rail Fuel Injection System

This report presents the results of an investigation to determine experimentally the instantaneous pressures at the discharge orifice of a common-rail fuel injection system in which the timing valve and cut-off valve were at some distance from the automatic fuel injection valve, and also to determine the methods by which the pressure fluctuations could be controlled. The results show that pressure wave phenomena occur between the high-pressure reservoir and the discharge orifice, but that these pressure waves can be controlled so as to be advantageous to the injection of the fuel. The results also give data applicable to the design of such an injection system for a high-speed compression-ignition engine.

Rothrock, A M↗