Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Unraveling kinking: A plasticity enhancing failure mode in high strength nano metallic laminates

Kinking is an important and plasticity-enhancing deformation/failure mode in numerous mechanically anisotropic materials including high-strength nano metallic laminates (NMLs). However, our current limited understanding of the mechanics of kinking and its dependence on microstructural attributes is insufficient for thoroughly comprehending and eventually being able to control failure behaviors of materials. In this study, we investigate kinking dependencies on microstructural attributes in NMLs via in situ micropillar compression, multiscale microstructure characterization, dislocation dynamic simulations, and crystal plasticity modeling. Additionally, by examining several NML systems (Cu/Fe, Ag/Fe, Al-4Mg/Fe), we demonstrate that the development of internal stresses during loading activates local layer-parallel glide triggering kinking in NMLs. Furthermore, this work reveals the effect of key microstructural features including layer thickness, layer waviness, interface barrier strength, and work hardening capacity on kink band formation in NMLs. More broadly, our efforts represent a generically applicable approach for probing large-strain deformation behavior of complex materials via synergetic modeling and experimental efforts.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of a Castable High Strength Secondary Aluminum Alloy from Recycled Wrought Aluminum Scrap

A new process for recycling scrap AA7075 aerospace alloys directly into a high strength castable secondary alloy is demonstrated. The process involves enhancing the castability of the utilized primary wrought aluminum scrap feedstock by scrap alloy chemistry optimization and zirconium additions in order to mitigate the inherent hot tearing tendency of 7075 alloys. By utilizing the new process, the hot tearing index of scrap AA7075 was reduced from 26 to 4. Defect-free castings were obtained in pilot-scale castings trials. The developed secondary 7075 alloy also satisfied preset target mechanical properties with strength levels exceeding 250 MPa and elongation levels higher than 3%. The validity of the new approach and its readiness for transition to commercial practice was demonstrated by casting cylinder heads directly from the modified 7075 scrap.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On the use of limestone calcined clay cement (LC3) in high-strength strain-hardening cement-based composites (HS-SHCC)

Highlights: • Use of LC{sup 3} slightly reduces flowability and shortens the setting time of fresh matrices. • Highly polymerized C-A-S-H gel and abundant ettringite benefit flexural strength of LC{sup 3}-matrices. • Use of LC{sup 3} enhances the bond strength between fiber and high-strength matrix. • LC{sup 3}-based HS-SHCC yields similar flexural performance as the composite with Portland cement. High-strength strain-hardening cement-based composites (HS-SHCC) demonstrate excellent mechanical and durability properties. However, high cement content typical to HS-SHCC results not only in high carbon footprint, but also in excessive hydration heat and severe autogenous shrinkage. In this investigation, Limestone Calcined Clay Cement (LC{sup 3}) was used to produce sustainable HS-SHCC. The LC{sup 3} substitution resulted in higher energy consumption during mixing and in shorter setting times of the fresh, plain matrices. Although the LC{sup 3} substitution slightly reduced the compressive strength, the formation of highly polymerized C-A-S-H gel and abundant ettringite benefited the flexural strength of the plain matrices. Additionally, single-fiber pullout experiments showed that the use of LC{sup 3} led to increased fiber-matrix bond strength and pullout energy. Finally, the replacement of Portland cement by LC{sup 3} resulted in HS-SHCC with similar mechanical performance to the reference composite, indicating a high potential for using LC{sup 3} in high-performance cement-based composites.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The Grain Boundary Relaxation (GBR) Approach for Manufacturing High Strength Nanocrystalline Lightweight Metals

The overarching goal of the project was to conduct research and development work as proposed in the Statement of Project Objective (SOPO) of the award document DE-FE-0009116. The project had 4 tasks and 12 milestones. All the milestone deliverables were completed. The accomplishments of the project objectives and technical discussions are described in Sections 3 and 4, respectively. The modeling and simulation work indicated that to increase the strength and stability of nanocrystalline aluminum (Al), selection of dopants, such as Mg, is necessary. It was predicted that the crystallite size should be less than 50 nm to give high strength. On the basis of modeling, cryo-milling of Al was conducted with the addition of Mg as a function of different times. The crystallite size of the cryo-milled powders was determined by XRD and TEM. Both measurements showed that the actual crystallite size of the grain was <40 nm. The thermal stability of the grain size was established as a function of temperature. It was established that the grain size was < 50 nm up to 500C. The crystallite size of the bulk sample prepared by spark plasma sintering (SPS) and cold spray (CS) additive manufacturing was less than <40 nm. The mechanical properties of the bulk samples prepared by SPS and CS, showed excellent microhardness, good tensile properties (>200 MPa) with moderate ductility and improved fatigue performance. Adding yttria stabilized zirconia (YSZ) improved the build thick of the CS sample, however the YSZ was getting embedded into the sample. A highly dense SPS samples sent for 3rd party testing to the Innovation Testing Services showed a minimum hardness of 180 HV with an average tensile strength of 512.5 MPa. The high cycle fatigue tests also showed an endurance limit of 179.5 MPa. The Energy cost evaluations showed an overall energy cost of around $\$$17.05 for the cryomilling and SPS processes and the total manufacturing cost calculations of $\$$78.14 for 1 kg of sample. The energy cost to prepare a Kg of CS sample is $\$$17.60 and the overall manufacturing cost is $\$$86.85.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High strength aluminum stamping

The invention provides a method of manufacturing a component formed of an aluminum alloy for use in an automotive vehicle application, for example those requiring high strength, light-weight, and a complex three-dimensional shape. The method begins by providing a blank formed of an aluminum alloy which is already solution heat treated and tempered, and thus has a temper designation of about T4. The method further includes heating the blank to a temperature of 150° C. to 350° C., preferably 190° C. to 225° C. The method next includes quickly transferring the blank to a hot or warm forming apparatus, and stamping the blank to form the complex three-dimensional shape. Immediately after the forming step, the component has a temper designation of about T6, but preferably not greater than T6, and thus is ready for use in the automotive vehicle application without any post heat treatment or machining.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Room Temperature Stamping of High-Strength Aluminum for Lightweight Structural Automotive Components

The use of aluminum (Al) 7xxx series in automobile structural applications is limited by factors such as its low room-temperature formability in T6 temper and the need for off-line artificial aging to regain high strength if it is formed in soft temper. In this study, two tempers were established that enable Al 7075 blanks to be room temperature stamped to create side impact beams that achieve near-T6 strength without post-forming artificial aging. It is shown that natural aging at room temperature, after solution treatment and before stamping, provides an alternative to high temperature pre-aging and hot stamping techniques in 7xxx alloys. Both tempers enabled room temperature stamping of the beams without cracking, indicating good formability. The Al beams were ~38% lighter than the benchmark boron steel beam. Further, the hardness in the low-deformation regions of the stamped Al beams were within 88% of a conventional 7075-T6 sheet. Paint-bake treatment of the beams appeared to cause over aging, lowering the ultimate tensile strength and ductility. Finite element three point bending simulations of the beams showed higher bending force and energy absorption before failure for the Al 7075 showing good promise for 7xxx series Al as a light-weight alternative to steel beams.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Influence of Mo Content on the Precipitation Behavior of 13Ni Maraging Ultra-High Strength Steels

This study offers valuable insights into the precipitation behavior of 13Ni maraging steels, emphasizing the role of molybdenum content in their microstructure, strengthening, and precipitate evolution. Precipitate morphology and crystallography were examined using a combination of high-resolution transmission electron microscopy and selected area electron diffraction. Strengthening mechanisms were assessed through Vickers hardness measurements. All the examined samples exhibited a lath martensite microstructure and displayed an increasing hardness over the aging time. The molybdenum content not only influenced the presence of retained austenite in the initial microstructure but also affected the type of precipitates formed during the early aging stages. Initially, Ni 3 Mo precipitates were formed, succeeded by the formation of more stable Fe 2 (Mo,Ti) Laves precipitates. The ultra-high strength of 13Ni maraging steels arises from the combination of the precipitate type and size distribution. The base composition of 13Ni maraging steels achieved a peak hardness of 798 HV1 through the precipitation of Laves Fe 2 (Mo,Ti) phases ranging from 3 to 14 nm in diameter.

13Ni maraging steels↗
DOE OSTI2020

Effects of secondary void-initiating particles on the steady-state crack growth resistance of high-strength steel

In this investigation, we focus on the dependence of stable crack growth resistance, as measured by the short-rod fracture toughness test, on secondary void-initiating particles such as AlN and Ti-based grain-refining precipitates in a variety of high-strength steels with tempered martensitic microstructures. The model developed by Ritchie and Thompson is modified to illustrate the significant amounts of toughening that can result from the refinement of secondary particles. Analysis of the data suggests that material strength is a predominant factor in increasing the short-rod fracture toughness relative to linear-elastic measures of initiation fracture toughness, but the extent of toughening is limited by the size and number density of secondary particles in the microstructure. The variation in estimates of secondary microvoid initiation and growth strains with precipitate size reinforce the notion that primary fracture at non-metallic inclusions and secondary fracture at smaller particles occur as sequential processes with a degree of concurrence that is dependent on the state of precipitation in both particle dispersions. Toughening in this connection is maximized by increases in microvoid growth strain that result from decreases in the size and areal number density of secondary void-initiating particles. Finally, the occurrence of transient instabilities during crack extension in short-rod specimens is explained with a phenomenological model that relates crack growth stability to natural variations in the dispersion of secondary void-initiating particles in the microstructure.

42 ENGINEERING↗
DOE OSTI2023

High-strength, lightweight nano-architected silica

Continuous nanolattices are an emerging class of mechanical metamaterials that are highly attractive due to their superior strength-to-weight ratios, which originate from their spatial architectures and nanoscale-sized elements possessing near-theoretical strength. Rational design of frameworks remains challenging below 50 nm because of limited methods to arrange small elements into complex architectures. Here, we fabricate silica frameworks with ~4- to 20-nm-thick elements using self-assembly and silica templating of DNA origami nanolattices and perform in situ micro-compression testing to examine the mechanical properties. We observe strong effects of lattice dimensions on yield strength (σ $\mathcal{y}$ ) and failure mode. Silica nanolattices are found to exhibit yield strengths higher than those of any known engineering materials with similar mass density. The robust coordination of the nanothin and strong silica elements leads to the combination of lightweight and high-strength framework materials offering an effective strategy for the fabrication of nanoarchitected materials with superior mechanical properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2025

Determination of Constraint-Independent Crack Tip Opening Angle for Stable Crack Growth in High-Strength Ductile Steels

The crack tip opening angle (CTOA) is one of fracture toughness parameters that has been used for decades in describing large stable crack growth in thin-walled aerospace structures under the low-constraint conditions. Recently, the pipeline industry has developed a growing interest in using the CTOA parameter to serve as the minimum required fracture toughness to arrest dynamic crack propagation in modern gas transmission pipelines made of high-strength ductile steel. To meet this industrial need, the CTOA test standard ASTM E3039 was therefore developed for measuring the constant critical CTOA. ASTM E3039 recommends a drop weight tearing test (DWTT) specimen with a shallow crack for standard CTOA testing, but its CTOA may depend on the low constraint condition of the DWTT specimen at the crack tip. Verifying the constraint independence of the DWTT-measured CTOA thus becomes indispensable for applying CTOA toughness to the running fracture control in the pipeline design. For this purpose, the present paper evaluates critical CTOA values in a set of fracture toughness tests on single-edge notched bend (SENB) specimens with shallow and deep cracks, based on four CTOA estimation models. Among these, the Ln(P)-LLD linear fit model is similar to that recommended by ASTM E3039 for CTOA calculation. Fracture test data for X80 pipeline steel and HY80 structural steel were considered in the CTOA evaluation. The results showed that the four CTOA models were able to determine a constraint independent CTOA value for stable crack growth in the SENB specimens. As a result, a single, reliable, constant CTOA value could be determined regardless of the specimen geometry or the crack-tip constraint conditions. Therefore, the CTOA measured using ASTM E3039 is constraint-independent and transferable to use in cases of actual cracks propagating in gas transmission pipelines.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effects of chemical segregation on ductility-anisotropy in high strength Fe-Mn-Al-C lightweight austenitic steels

Ductile Fe-Mn-Al-C lightweight steels offer great potential as high specific strength materials for weight critical applications. In the present work, very high yield (~1 GPa) and ultimate tensile strength levels (~1.5 GPa) were obtained along the rolling and transverse directions of Fe-30Mn-8.5Al-0.9Si-0.9C-0.5Mo (wt.%), with high tensile elongation to failure of ~35%. This excellent mechanical behavior was attributed to the nanoscale, ordered κ-carbide precipitates formed during aging after rolling. However, tensile ductility was not isotropic through all directions of the rolled plate. In particular, the ductility was consistently lower than 5% true strain along the normal direction. Upon detailed microstructural investigations, micro-scale lamellar chemical micro-segregation bands were detected, which caused the observed anisotropic embrittlement along certain plate directions. These bands resulted in low failure strains along the normal direction since it is oriented perpendicular to these chemical segregation bands, resulting in a failure type reminiscent of delamination-induced cleavage fracture. Chemical segregation causes an inhomogeneous κ-carbide precipitate distribution upon aging, producing more pronounced mechanical anisotropy after peak-aging as compared to the solution heat treated samples. Surprisingly, deformation twinning was observed after tensile deformation of solution-heat treated specimens via electron-backscatter diffraction experiments, which is anomalous for a high stacking faulty energy (SFE) material. Further, it was proposed that chemical micro-segregation promotes locally different SFE regions, leading to deformation twinning in this nominally high SFE material. Overall, this work demonstrates the effects of chemical segregation on mechanical properties and microstructural evolution in a high performance, lightweight Fe-Mn-Al-C steel.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

High Velocity Joining of Multi-material Stacks Containing 3rd Generation Advanced High-Strength Stainless Steel and Aluminum Extrusion and Casting (Abstract)

Advanced lightweight materials, including multi-phase steels, aluminum extrusions and aluminum castings, have increasingly replaced mild steel to meet original equipment manufacturer (OEM) demand for increased fuel economy and crash-safety requirements. Third Generation (Gen 3) AHSS provides a superior combination of strength and ductility for crash energy management components in the vehicle body-in-white (BIW). Aluminum extrusions are widely used for bumper, door rocker panel, cradle and battery frame applications. Aluminum castings are increasingly being used in electric vehicles to provide part consolidation, weight saving and increased driving range. Rocker panels are, for example, an important component of the battery electric vehicle (BEV) body structure. The rocker panel serves several purposes, including structural support, crash resistance, protection for the vehicle's underbody and battery tray, and contributing to the overall aesthetics. In order to reduce weight, rocker panels are usually constructed using outer panels consisting of 3rd generation advanced high strength steels (AHSS) and an inner multicell aluminum extrusion structure for energy absorption which protects the batteries in a crash event. It is well known, however, that these material combinations provide significant challenges for joining and are susceptible to liquid metal embrittlement and loss of strength. The overall goal is to find a solution that addresses these challenges in order to produce multi-material vehicle components with reduced weight and minimal galvanic and recyclability issues. The approach being proposed here is to utilize a novel high velocity (HiVe) riveting and clinching technique recently demonstrated by Pacific Northwest National Laboratory (PNNL) to join (2T/3T) sheets of aluminum alloys and steel. This process will not only address the aforementioned challenges but also help significantly reduce the joining cycle time. This work will also demonstrate use of HiVe assemblies to be retrofitted to existing body-shop robots thus having minimal impact to existing body shop operations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Low Weight, High Strength Coal-Based Building Materials for Infrastructure Products (Rev.A)

Semplastics has developed, tested, and proven the viability of a new class of composite infrastructure components that use coal as the primary component. Phase I resulted in the production of brick and block components, called X-BRIX and X-BLOX, with dimensions comparable to commercially available bricks and concrete blocks, but with superior mechanical strength, lower weight, greater hardness, improved toughness, greater abrasion resistance, and greater chemical resistance than concrete. Multiple samples of full-size (16” × 8” × 8”) X-BLOX and full-size (8” × 4” × 2.5”) X-BRIX were made to demonstrate the technology, and to support the development of mortar or joining techniques. Phase I moved the coal-based composite materials technology from a current Technology Readiness Level (TRL) of 3 to TRL 5. Semplastics’ coal-based composite materials exhibit a number of high-performance characteristics, including high strength (five times the flexure strength of the best commercial brick, and more than twice the compressive strength of construction-grade concrete block), lower density (by 37 to 41%), improved mechanical durability and abrasion resistance, and resistance to chemicals, acids, salts, and chemical wastewater. These properties offer significant improvements over conventional bricks, concrete blocks, and pavers. The coal particles are completely encapsulated and bonded using a specially formulated polymer-derived ceramic (PDC) that is cured to form an “aggregate” of coal and PDC resin. This aggregate can be further processed and lightly pressed (at 10 to 50 psi) to produce a brick. After pyrolyzing (similar to the processing used to make standard clay bricks), the finished coal-based brick is significantly harder and more abrasion-resistant than regular bricks. We have produced prototype X-BRIX and X-BLOX that contain at least 55% coal by weight (71% carbon by weight, due to the controlled carbon content of the PDC) and showed their superior mechanical properties through in-house and contracted testing.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Reducing Mass of Steel Auto Bodies using Thin Advanced High Strength Steel with Carbon-Fiber Reinforced Epoxy

Diversitak, a company based in Detroit, MI, has developed a proprietary, low specific gravity, carbon fiber-reinforced epoxy (CFRE) under U.S. patent number 9,963,58832. Preliminary testing on this new material conducted in collaboration with ArcelorMittal Steel Company proved out the CFRE concept. A thin layer of this CFRE was applied to a stamped sheet of steel with residual stamping oils from a mill, in a time corresponding to automotive processing (e.g., ~15 seconds), and processed following automotive e-coat procedures (phosphating + 175–200°C heating), to complete the curing. No problems with adherence or performance were noted. While the CFRE does add weight to a thin gauge steel panel, it weighs much less than what is displaced by using thicker conventional mild steel gauges. The application of the coating showed a significant increased dent resistance, oil canning resistance, and part stiffness.This current two-year project was designed to mature this new technology to near manufacturing readiness to reduce the weight of a vehicle and lower the cost of weight reduction. The process involves the use of thinner gauge steels than are currently used. The collaborative development team included two industrial manufacturers: Diversitak and ArcelorMittal Steel Company; LightMAT; and two National Laboratories: Oak Ridge National Laboratory (ORNL) and Idaho National Laboratory (INL). The team developed a new manufacturing process to reduce the weight of a vehicle and lower the cost of weight reduction, as well as a better understanding of how to apply the coating so that it will perform to a high standard in-service. The team also performed an in-depth study to determine the long-term durability of the materials manufactured using this technology and well-known automotive industry standard tests.The overall process involved stiffening the thinner gauge steel by applying the CFRE on only one side. To accomplish this goal, the optimal reinforcement fiber length and fiber concentration was first determined. This was followed by measuring the coefficient of thermal expansion (CTE) in all three directions, so it could be fed into manufacturing models and methods for rapidly and inexpensively applying the coating. This was followed by panel level evaluations of the coating and steel combination, and then by full part demonstration of the technology on door panels. The final step was corrosion testing of the parts.ArcelorMittal characterized the advanced high strength steel (AHSS) (e.g., metallurgy-heat treatment for required AHSS properties as a function of the sheet thickness, state of internal stress) and quantified CFRE adhesion to the steel as a function of sheet preparation (e.g., rolling and stamping).ORNL optimized the fiber length, fiber concentration, and coating thickness for best vehicle function and performance at the least cost. Along with the suppliers, ORNL developed a durable CFRE application process (e.g., gun material, design, robotic dispensing process) and identified the adhesion stability of the CFRE during process holding. An approach to ensure that application/curing timing conforms to conventional assembly line speed and plant cycle times was determined. ORNL also determined the CTE of the material in all three directions and performed material scanning electron microscopy (SEM) analyses.INL characterized the corrosion properties of the steel panels coated with CFRE. The panels were investigated for corrosion resistance and stability as replacement materials used in automotive body panels to reduce mass. The coupons tested at INL were supplied by Diversitak after an optimized CFRE formulation was achieved in the already coated form for corrosion testing.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Rotary Inertia Friction Welding of Dissimilar High-Strength 422 Martensitic Stainless Steel and 4140 Low Alloy Steel for Heavy-Duty Engine Piston Fabrication

AISI 422 martensitic stainless steel with superior high temperature performance (oxidation resistance and strength) is under evaluation for replacing current heavy-duty piston crown materials, AISI 4140 martensitic steel and micro alloyed steel (MAS) 38MnSiVS5, to fabricate a multimaterial piston. This multimaterial piston concept further improved power density and fuel economy by allowing heavyduty diesel engines to operate at higher temperatures and pressures. Joining AISI 422 steel piston crowns with AISI 4140 steel piston skirts is a key manufacturing step for this multimaterial piston. However, the significant differences in strength, elevated temperature flow stress, alloy chemistry, and temper resistance between these two martensitic steels cause some weldability issues (cracking) and metallurgical challenges (alloying element migration/segregation) when using conventional fusion-based welding processes. Rotary inertia friction welding (RIFW), a solid-state welding process, has been the preferred method to join 4140 crowns to 4140 skirts (and MAS crowns to MAS skirts) in high-volume production of current heavy-duty diesel engine pistons. It has been used to join these two materials with relatively comparable alloy chemistry to fabricate pistons with MAS skirts and 4140 crowns. Meanwhile, RIFW has also been a preferred method of dissimilar metal welding. However, RIFW of dissimilar high-strength martensitic steels has yet to be widely pursued. The interfacial microstructure complexities created by the thermomechanical process and highly nonequilibrium phase transformations during RIFW are a significant challenge for understanding and predicting their joining behavior and have not been reported in detail. Here, in this work, defect-free AISI 422 steel-AISI 4140 multimaterial pistons were successfully fabricated using the RIFW process. The interfacial microstructure and mechanical properties of dissimilar 422/4140 steel RIFW in the as-welded condition were experimentally studied in detail. The results provide critical baseline information for understanding RIFW mechanisms and guiding subsequent postweld heat treatment (PWHT) practice.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High-modulus, high-strength, low alloy gray cast iron for cylinder liners and automotive applications

A high elastic modulus, high ultimate tensile strength, and low alloy gray cast iron for cylinder liners. The gray cast iron includes from 2.60 wt % to 3.30 wt % Carbon (C); from 1.50 wt % to 2.30 wt % Silicon (Si); from 0.30 wt % to 0.80 wt % Manganese (Mn); from 0.15 wt % to 0.35 wt % Phosphorus (P); from 0.05 wt % to 0.11 wt % Sulphur (S); from 0.60 wt % to 1.20 wt % Copper (Cu); from 0.10 wt % to 0.30 wt % Chromium (Cr); from greater than 0.0 wt % to 0.1 wt % Nickle (Ni); from 0.15 wt % to 0.40 wt % Molybdenum (Mo); and balance wt % Iron (Fe). The total wt % of Si, Mn, P, S, Cu, Cr, Ni, and Mo is less than about 4.10 wt %. The gray cast iron has a Carbon Equivalent (CE) from 3.00 wt % to 3.90 wt % and the product of Mn %*S % is from 0.025 to 0.045.

Yang, Jianghuai↗
DOE OSTI2023

Ultrafine-grained Fe-TiB 2 high-modulus nanocomposite steel with high strength and isotropic mechanical properties by laser powder bed fusion

Fe-TiB 2 metal matrix composite, also called high-modulus steels (HMSs), are of great interest for applications in fuel-efficient transportation infrastructure, aerospace, and wear industries due to their high specific stiffness and yield strength. However, conventional cast Fe-TiB 2 HMSs often contain coarse and sharp-edged TiB 2 particles which easily trigger premature cracking during loading. Here, we synthesized a Fe-TiB 2 nanocomposite HMS via laser powder bed fusion (LPBF) additive manufacturing of mixed micro-sized powders of Fe, Ti, and Fe 2 B. We investigated the microstructure formation and mechanical behavior of the Fe-TiB 2 HMS. We found that in situ chemical reaction of Ti and Fe 2 B enables the formation of TiB 2 particles at nanoscale during rapid solidification of LPBF. These nanoscale TiB 2 particles can serve as heterogeneous nucleation sites and promote the formation of ultrafine and equiaxed α-Fe grains with random crystallographic textures, which differ from many other additively manufactured (AM) metal alloys characteristic of strong crystallographic textures. As such, isotropic mechanical properties were achieved in the AM Fe-TiB 2 nanocomposite HMS with a high elastic modulus of ~ 240 GPa, an exceptional yield strength of ~ 1450 MPa, and a large plasticity of ~ 20% under compression. Quantitative analysis reveals that the high yield strength primarily originates from strengthening contributions of the ultrafine grains with an average grain size of ~450 nm, the nanoscale TiB 2 reinforcing particles of 20–180 nm, and a high density of printing-induced dislocations of the order of 10 15 m –2 . In situ synchrotron high-energy X-ray diffraction unveils the load partitioning from the softer α-Fe matrix to the stiffer and stronger TiB 2 nanoparticles, contributing to the sustained strain hardening during compression. Our work not only provides a general pathway for achieving high-performance metal matrix nanocomposites by in situ chemical reaction and precipitation of ceramic nanoparticles during additive manufacturing, but also offers mechanistic insights into the deformation mechanism of nanoparticle-reinforced HMS composites.

36 MATERIALS SCIENCE↗