SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Pulse amplitude discriminator is specially designed for nuclear counting applications. At very high rates, the threshold is stable. The output-pulse width and the dead time change negligibly. The unit incorporates a provision for automatic dead-time correction.
Numerical and experimental results are presented on the pullout phenomenon in composite materials at a high rate of loading. The finite element method was used, taking into account the existence of a virtual shear deformation layer as the interface between fiber and matrix. Experimental results agree well with those obtained by the finite element method. Numerical results show that the interlaminar shear stress is time dependent, in addition, it is shown to depend on the applied load time history. Under step pulse loading, the interlaminar shear stress fluctuates, finally decaying to its value under static loading.
This report documents the analysis and experimental validation of the performance of various aspects of a high rate bit synchronizer.
The performance and abuse characteristics of 55 D-size lithium-thionyl chloride (Li-SOCl2) cells are evaluated at relatively high rates. Results from the following tests are presented: shock test, vibration test, capacity performance, uninsulated short circuit, high temperature exposure, and overdischarge.
A four-port magic-T hybrid waveguide junction serves as the central component of a high-efficiency two-way power combiner circuit for transmitting a high-rate phase-modulated digital signal at a carrier frequency in the Ka-band (between 27 and 40 GHz). This power combiner was developed to satisfy a specific requirement to efficiently combine the coherent outputs of two traveling-wavetube (TWT) amplifiers that are typically characterized by power levels on the order of 100 W or more. In this application, the use of a waveguide-based power combiner (instead of a coaxial-cable- or microstrip-based power combiner, for example) is dictated by requirements for low loss, high power-handling capability, and broadband response. Combiner efficiencies were typically 90 percent or more over both the linear and saturated output power regions of operation of the TWTs . Figure 1 depicts the basic configuration of the magic-T hybrid junction. The coherent outputs of the two TWTs enter through ports 1 and 4. As a result of the orientations of the electromagnetic fields, which also provides a needed high port-to-port isolation, of these two input signals and the interior design of the magic-T junction, the input powers are divided so as to add in phase at one output port (port 2), and to be opposite in phase and hence cancel each other at the opposite coplanar output port (port 3). The net result is that the output power at port 2 is essentially double that of the output of one TWT, minus the power lost in the magic-T hybrid junction. Optimum performance as a high-efficiency power combiner thus requires a balance of both power and phase at the input ports of the magic-T. Replicas of this two-way combiner can be arranged in a binary configuration to obtain a 2n-way (where n is an integer) combiner. For example, Figure 2 illustrates the use of three two-way combiners to combine the outputs of four TWTs.
We present performance data for low-noise free-running high-rate photon counting method for space optical communication and ranging. NASA GSFC is testing the performance of two types of novel photon-counting detectors 1) a 2x8 mercury cadmium telluride (HgCdTe) avalanche array made by DRS Inc., and a 2) a commercial 2880-element silicon avalanche photodiode (APD) array. We successfully measured real-time communication performance using both the 2 detected-photon threshold and logic AND-gate coincidence methods. Use of these methods allows mitigation of dark count, after-pulsing and background noise effects without using other method of Time Gating The HgCdTe APD array routinely demonstrated very high photon detection efficiencies ((is) greater than 50%) at near infrared wavelength. The commercial silicon APD array exhibited a fast output with rise times of 300 ps and pulse widths of 600 ps. On-chip individually filtered signals from the entire array were multiplexed onto a single fast output. NASA GSFC has tested both detectors for their potential application for space communications and ranging. We developed and compare their performances using both the 2 detected photon threshold and coincidence methods.
We present performance data for low-noise free-running high-rate photon counting method for space optical communication and ranging. NASA GSFC is testing the performance of two types of novel photon-counting detectors 1) a 2x8 mercury cadmium telluride (HgCdTe) avalanche array made by DRS Inc., and a 2) a commercial 2880-element silicon avalanche photodiode (APD) array. We successfully measured real-time communication performance using both the 2 detected-photon threshold and logic AND-gate coincidence methods. Use of these methods allows mitigation of dark count, after-pulsing and background noise effects without using other method of Time Gating The HgCdTe APD array routinely demonstrated very high photon detection efficiencies (50) at near infrared wavelength. The commercial silicon APD array exhibited a fast output with rise times of 300 ps and pulse widths of 600 ps. On-chip individually filtered signals from the entire array were multiplexed onto a single fast output. NASA GSFC has tested both detectors for their potential application for space communications and ranging. We developed and compare their performances using both the 2 detected photon threshold and coincidence methods.
A neighbor discovery protocol that enables the dynamic discovery of nodes for NASA Glenn Research Center’s High Rate Delay Tolerant Networking (HDTN) project is needed to satisfy mission scalability and interoperability objectives. The purpose of this study is to primarily examine a DTN IP neighbor discovery (IPND) implementation to understand the inner workings of the protocol before approaching a neighbor discovery implementation for the HDTN project. Using a rust-based DTN IPND implementation, this study analyzed the neighbor discovery process. DTN IPND was found to help meet both mission scalability and interoperability objectives by enabling dynamic routing capabilities. This study definitively answers the question regarding mission scalability and interoperability concerns. Further studies are needed to establish the most optimal neighbor discovery implementation for HDTN.
In order to meet ever-increasing data return requirements, more satellites are using the near-Earth Ka-band (25.5 – 27.0 GHz) to achieve higher downlink rates. The paper discusses the Universal Space Transponder - Ka-band Modulator (UST-KaM) developed at the NASA Jet Propulsion Laboratory for the NASA-ISRO SAR (NISAR) mission, which is capable of transmitting up to 1.74 Gbps with 7/8 LDPC encoding. The UST-KaM utilizes OQPSK with both baseband and RF filtering to contain the 1 Gsps transmission spectrum within the 1.5 GHz Ka-band, even with the use of an external, saturated amplifier. Due to the high data rates involved, several technical hurdles were overcome in both the digital and RF designs. The UST-KaM is a software defined radio with two digital circuit board assemblies: a low speed housekeeper board for commanding and telemetry, and a high-rate signal processing board known as the Signal Processing Module (SPM). The SPM receives data from the spacecraft via a SERDES interface at up to 2 Gbps, processes and encodes the data using a Xilinx Virtex-5 FPGA, and produces 1 Gsps OQPSK I and Q waveforms via synchronized, multiplexed DACs. The RF Electronics in the UST-KaM employ a heterodyne architecture in which the I/Q digital waveforms are filtered and then up-converted using a sub-harmonic IQ mixer. The LO of the converter, which is included in the exciter assembly, is at 13.125GHz, and the RF output is a 26.25GHz carrier which is modulated with the OQPSK waveforms. The output of the mixer is then filtered using low loss quartz thinfilm edge coupled Chebyshev filters and amplified through a series of low gain Ka-Band amplifiers. The exciter assembly also has a 2GHz, low-phase-noise, PLL synthesizer to supply the clock to the DACs for the high rate digital waveforms.
The heat dissipation problem occurring in the lithium thionyl chloride cells discharged at relatively high rates under normal discharge conditions is examined. Four heat flow paths were identified, and the thermal resistances of the relating cell components along each flow path were accordingly calculated. From the thermal resistance network analysis, it was demonstrated that about 90 percent of the total heat produced within the cell should be dissipated along the radial direction in a spirally wound cell. In addition, the threshold value of the heat generation rate at which cell internal temperature could be maintained below 100 C, was calculated from total thermal resistance and found to be 2.9 W. However, these calculations were made only at the cell components' level, and the transient nature of the heat accumulation and dissipation was not considered. A simple transient model based on the lumped-heat-capacity concept was developed to predict the time-dependent cell temperature at different discharge rates. The overall objective was to examine the influence of cell design variable from the heat removal point of view under normal discharge conditions and to make recommendations to build more efficient lithium cells.
Some materials, such as steel, titanium, and tungsten, have a yield stress that depends on the strain rate, and actually are stronger at high rates of load or deformation. The increase in strength is relevant; and if not taken into account, the computer models will not match the experimental behavior observed in typical shock loading, ordnance, or ballistic tests. For higher velocity (hypervelocity impacts), an equation of state that accounts for non-linearities and temperature in the pressure-volume relation, may also be needed. This rate-dependent behavior of the strength has also been observed in some composite materials. Southwest Research Institute® (SwRI®) has started an internal research effort to measure and better model the behavior of materials, in particular carbon/carbon composites like ACC-6, at ultra-high temperatures for both static and high rates of deformation. The ultimate objective is to obtain reliable computer models of carbon/carbon material under hypersonic flight conditions, hypervelocity impacts, shock-loading situations such as booster-vehicle separation, and munition operation events. SwRI® has successfully modeled in the past ballistic impact on other composites, namely S-2 glass/epoxy, Kevlar/resin, polyethylene fibers/resin, and carbon fiber composites. This presentation will show test results relevant to the strength properties of the ACC-6 C/C material which were measured at quasistatic, medium, and the moderately high strain rates (~103 s—1) achievable in a conventional Split Hopkinson bar apparatus. Some of the tests were performed at both high-rates and high temperatures typical of hypersonic flight, something that, to the authors’ knowledge, has never been published in the past for this particular material. The test method will be presented, as well as the comparison of the stress-strain curves for the different temperatures and strain-rates of interest. A discussion of how the results can be used in the typical hydrocodes of interest will be included.
Tlis paper presents an overview of the preliminary design of both the flight and ground systems of the Optical Communication Demonstration and High-Rate Link Facility which will demonstrate optical communication from the International Space Station to ground after its deployment in October 2002. The overview of the preliminary design of the Flight System proceeds by contrasting it with the design of the laboratory-model unit, emphasizing key changes and the rationale behind the design choices. After presenting the preliminary design of the Ground System, the timetable for the construction and deployment of the flight and ground systems is outlined.
A study was sponsored to investigate a set of end-to-end system concepts for implementing a high-rate duplex direct data distribution (D4) space-to-ground communications link. The NASA Glenn Research Center is investigating these systems (both commercial and Government) as a possible method of providing a D4 communications service between NASA spacecraft in low Earth orbit and the respective principal investigators using or monitoring instruments aboard these spacecraft. Candidate commercial services were assessed regarding their near-term potential to provide a D4 type of service. The candidates included K-band and V-band geostationary orbit and nongeostationary orbit satellite relay services and direct downlink (D3) services. Internet protocol (IP) networking technologies were evaluated to enable the user-directed distribution and delivery of science data. Four realistic, near-future concepts were analyzed: 1) A duplex direct link (uplink plus downlink communication paths) between a low-Earth-orbit spacecraft and a principal-investigator-based autonomous Earth station; 2) A space-based relay using a future K-band nongeosynchronous-orbit system to handle both the uplink and downlink communication paths; 3) A hybrid link using both direct and relay services to achieve full duplex capability; 4) A dual-mode concept consisting of both a duplex direct link and a space relay duplex link operating independently. The concepts were analyzed in terms of contact time between the NASA spacecraft and the communications service and the achievable data throughput. Throughput estimates for the D4 systems were based on the infusion of advanced communications technology products (single and multibeam K-band phased-arrays and digital modems) being developed by Glenn. Cost estimates were also performed using extrapolated information from both terrestrial and current satellite communications providers. The throughput and cost estimates were used to compare the concepts.
Multichannel analyzer, used with a gating system incorporating pole-zero compensation, pile-up rejection, and baseline-restoration, achieves good resolution at high rates of input. It improves resolution, reduces tailing and rate-contributed continuum, and eliminates spectral shift.
RF carrier uses two receiver systems to increase signal-to-noise ratio and sensitivity. Signals separately processed are coherently combined at summing junction for improved reception of marginal high-rate signals frequently lost to system, atmosphere, and galactic noises. Two receivers improve ratio by 2.7 dB; improvement is made by arraying more receiver systems.
A document discusses the creation of a Ka-band modulator developed specifically for the NASA/GSFC Solar Dynamics Observatory (SDO). This flight design consists of a high-bandwidth, Quadriphase Shift Keying (QPSK) vector modulator with radiation-hardened, high-rate driver circuitry that receives I and Q channel data. The radiationhard design enables SDO fs Ka-band communications downlink system to transmit 130 Mbps (300 Msps after data encoding) of science instrument data to the ground system continuously throughout the mission fs minimum life of five years. The low error vector magnitude (EVM) of the modulator lowers the implementation loss of the transmitter in which it is used, thereby increasing the overall communication system link margin. The modulator comprises a component within the SDO transmitter, and meets the following specifications over a 0 to 40 C operational temperature range: QPSK/OQPSK modulator, 300-Msps symbol rate, 26.5-GHz center frequency, error vector magnitude less than or equal to 10 percent rms, and compliance with the NTIA (National Telecommunications and Information Administration) spectral mask.
The NASA Deep Space Network (DSN) has a new requirement to support high-data-rate Category A (Cat A) missions (within 2 million kilometers of Earth) with simultaneous S-band uplink, S-band downlink and Ka-band downlink. The S-band links are required for traditional TT&C (Telemetry, Tracking, and Command) support to the spacecraft, while the Ka-band link is intended for high-data-rate science returns. The new Ka-band system combines the use of proven DSN cryogenic designs, for low system temperature, and high data rate capability using commercial telemetry receivers. The initial Cat A support is required for the James Webb Space Telescope (JWST) in 2013 and possibly other missions. The upgrade has been implemented into 3 different 34-meter Beam Waveguide (BWG) antennas in the DSN, one at each of the complexes in Canberra (Australia), Goldstone (California) and Madrid (Spain). System test data is presented to show that the requirements were met and the DSN is ready for Cat A Ka-band operational support.
A method for increasing the sensitivity for radio frequency reception is described. Receiving systems or stations are arrayed in such a manner as to provide signal to noise ratio improvement relative to a single receiving system or station. Radio frequency carrier arraying for high rate telemetry that provides signal to noise ratio improvement for RF carrier reception and demodulation is discussed.