Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hardening rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Hot deformation behavior of an industrially cast large grained low density austenitic steel

Hot compression testing was performed on specimens of an Fe–30Mn–9Al–1Si-0.9C-0.5Mo wt.% low density steel which were extracted from an industrial casting with large grain size (320 ± 50 μm). Grain boundaries act as nucleation sites for dynamic recrystallization in the present material and the large grain size results in fewer nucleation sites, which delays dynamic recrystallization to larger strains and/or higher temperatures and causes higher rates of work hardening relative to similar materials but with smaller grain sizes. Here, a relatively high activation energy for hot deformation of 470 ± 90 kJ mol –1 was determined from a Zener-Hollomon analysis of the flow stresses at different temperatures and strain rates, attributed in part to the large grain size.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal-Mechanical Elastic-Plastic and Ductile Failure Model Calibrations for 304L Stainless Steel Alloy

Numerical simulations of metallic structures undergoing rapid loading into the plastic range require material models that accurately represent the response. In general, the material response can be seen as having four interrelated parts: the baseline response under slow loading, the effect of strain rate, the conversion of plastic work into heat and the effect of temperature. In essence, the material behaves in a thermal-mechanical manner if the loading is fast enough so when heat is generated by plastic deformation it raises the temperature and therefore influences the mechanical response. In these cases, appropriate models that can capture the aspects listed above are necessary. The material of interest here is 304L stainless steel, and the objective of this work is to calibrate thermal-mechanical models: one for the constitutive behavior and another for failure. The work was accomplished by first designing and conducting a material test program to provide data for the calibration of the models. The test program included uniaxial tension tests conducted at room temperature, 150 and 300 C and at strain rates between 10 –4 and 10 3 1/s. It also included notched tension and shear-dominated compression hat tests specifically designed to calibrate the failure model. All test specimens were extracted from a single piece of plate to maintain consistency. The constitutive model adopted was a modular $J_2$ plasticity model with isotropic hardening that included rate and temperature dependence. A criterion for failure initiation based on a critical value of equivalent plastic strain fitted the failure data appropriately and was adopted. Possible ranges of the values of the parameters of the models were determined partially on historical data from calibrations of the same alloy from other lots and are given here. The calibration of the parameters of the models were based on finite element simulations of the various material tests using relatively ne meshes and hexahedral elements. When using the model in structural finite element calculations, however, element formulations and sizes different from those in the calibration are likely to be used. A brief investigation demonstrated that the failure initiation predictions can be particularly sensitive to the element selection and provided an initial guide to compensate for the effect of element size in a specific example.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dislocation density-based plasticity model from massive discrete dislocation dynamics database

In this work, we present a dislocation density-based strain hardening model for single crystal copper through a systematic coarse-graining analysis of more than 200 discrete dislocation dynamics (DDD) simulations of plastic deformation under uniaxial tension. The proposed constitutive model has two components: a generalized Taylor relation connecting resolved shear stresses to dislocation densities on individual slip systems, and a generalized Kocks-Mecking model for dislocation multiplication. The DDD data strongly suggests a logarithmic dependence of flow stress on the plastic shear strain rate on each slip system, and, equivalently, an exponential dependence of the plastic shear strain rate on the resolved shear stress. Hence the proposed generalized Taylor relation subsumes the Orowan relation for plastic flow. The DDD data also calls for a correction to the Kocks-Mecking model of dislocation multiplication to account for the increase of dislocation density on slip systems with negligible plastic shear strain rate. This is accomplished by allowing the multiplication rate on each slip system to include contributions from the plastic strain rates of the two coplanar slip systems. The resulting constitutive model successfully captures the strain hardening rate dependence on the loading orientation as predicted by the DDD simulations, which is also consistent with existing experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Assessment of reverse gun taylor cylinder experimental configuration

Experimental efforts for Taylor-anvil impact tests have often been limited to near room temperature. The ‘Reverse Gun’ method proposed by Gust in 1982 allows for the Taylor impact specimen to be uniformly heated without temperature losses before impact. Through the use of finite element analysis, we explore two topics in this work. First, we examine whether the reverse gun experimental configuration is comparable to the traditional Taylor-anvil setup. Second, we assess the accuracy of several commonly employed flow strength models in terms of their ability to predict the reverse gun experimental results which involve dynamic loading conditions and complex thermo-mechanical coupling. The reverse gun simulations are performed for tantalum targets at initial temperatures in the range 295 K to 1295 K and velocities from 135 m/s to 242 m/s. We show that with suitable care in the modeling of the preheated reverse gun experiments one can make valuable assessments of flow strength models. Given the conditions explored, these observations probe the thermal softening, strain hardening, and strain rate sensitivity of the material.

42 ENGINEERING↗
DOE OSTI2021

Response of 304L stainless steel and 6061-T651 aluminum alloy at -40 °C

The objective of this work is to extend the thermal-mechanical, elastic-plastic calibrations for 304L stainless steel [1] and and 6061-T651 aluminum alloy [2] to the regime between room temperature and -40 °C. The basis to extend the calibration consisted of new uniaxial tension tests conducted at -40 °C using the same plate material stocks, circular cylindrical specimen geometries and testing apparatus as previously, followed by attempts to fit power-law hardening functions to replicate the response observed in the specimens and then extend the yield, hardening constant, hardening exponent and rate constant functions in the calibrations to cover the new temperature regime.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Solute effects upon dislocation motion and recovery in Mg alloys (Final Report)

The objective the research was to develop a firmer understanding of the interactions between substitutional solute atoms and dislocations within Mg alloys. These interactions govern the absolute and relative mobilities of various types of dislocations in Mg (e.g., basal < a>, non-basal < a>, and pyramidal < c+a>). Furthermore, they have an impact on dislocation recovery processes (e.g., cross-glide, climb, rearrangement, and annihilation). Ultimately, solute-dislocation interactions strongly impact a) strain hardening, b) strain rate sensitivity, c) plastic anisotropy of textured polycrystals, d) texture evolution, e) dislocation substructures evolution, and even f) recrystallization behavior. It is broadly known that Mg alloys exhibit poor low temperature formability. Since formability is largely governed by properties (a) – (c) in this list, it is critical to develop a better understanding of solute-dislocation interactions, if one hopes to improve the situation. While the theory of static solute strengthening is well developed, especially for alloys with face centered cubic (FCC) crystal structures, there are outstanding questions related to applications to hexagonal close packed (HCP) crystal structures and dynamic strain aging (DSA) in materials of various structures. DSA has far-reaching implications for metal formability and, in the case of Mg alloys, appears to correlate with the so-called rare-earth (RE) texture which has been shown to benefit formability. The Portevin-Le Chatelier (PLC) effect, and associated negative strain rate sensitivity, occur at higher temperatures (>100℃) in Mg alloys as compared with similar Al alloys, even though they have similar melting points and solute diffusivities. Our preliminary research has shown that modern, physics-based models of DSA can be tuned to describe the behavior of Mg alloys if a rather higher activation enthalpy is assumed for cross-core diffusivity. While this partially explains the delay in DSA to higher temperatures, it is also hypothesized that this delay is due in part to the intrinsically more thermally activated (rate sensitive) nature of non-basal < a> dislocation motion which is required for macroscopic flow of Mg alloys, whereas octahedral slip in many FCC metals like aluminum is essentially athermal at room temperature. It was originally proposed to employ a combination of in-situ diffraction-based experimental characterization to validate existing theory. It was envisioned to perform in-situ transmission electron microscopy (TEM) to assess individual dislocation behavior and in-situ high-energy X-ray diffraction (HEXRD) techniques which were showing great promise for elucidating collective dislocation behavior, 2 including recovery, especially if the contributions to various forms of diffraction peak broadening (𝜂𝜂,𝜔𝜔,and 2𝜃𝜃) can be effectively integrated. Finally, it was envisioned to perform discrete dislocation dynamics (DDD) modeling approaches to aide in the interpretation of both TEM and HEXRD experiments. In the end, mechanical tests were performed on more complex Mg alloys which exhibited evidence of dynamic strain aging, and this led to the establishment of another project. Mechanical test data obtained at McMaster University served as the basis of an assessment of the applicability of Bazinski’s “stress equivalence” theory of solute strengthening to polycrystalline alloys of Mg. Although we did not succeed in applying the approach to Mg alloys, we did develop expertise with the HEXRD approach using a BCC, β-Ti alloy and demonstrated numerous new capabilities that may be applied to any polycrystalline material in collaboration with researchers at CHESS and around the world: (1) assessment of details of the elastoplastic transition (yielding) using a combination of HEXRD and full-field polycrystal plasticity modeling, (2) the first-ever experimental observation of strong stress rotation within the individual grains of a polycrystalline material, and (3) a comprehensive analysis of the grain-level dislocation density evolution based upon diffraction peak broadening along 𝜂𝜂,𝜔𝜔,and 2𝜃𝜃 directions. This final aspect allowed us to confirm that dislocations were gliding on multiple plane types and not restricted to {110} type planes, and it also provided clues as to why some grains were unloading during straining, with surprising implications for our understanding of the effects of geometrically necessary dislocations (GNDs). Finally, graduate student, Mohammed Shabana, developed a MATLAB code which confirmed the conclusions of Prof. Catalin Picu (Rensallear Polytechnic Institute, RPI) regarding the effect of solute-trapped, forest dislocations on the breaking stress of Lomer lock junctions in FCC metal alloys. He applied the same anisotropic line-tension model to a variety of dislocation junction configurations and found an inconsistency in the widely cited results of Dupuy and Fivel regarding the Hirth Lock, and he outlined an approach to extend these finding to HCP Mg alloys that we are still pursuing with discretionary fundings at UVA.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Carbon Fiber and Polymer Composites

Tooling is an integral part of composites manufacturing. Composite tools, also called ‘soft’ tools, are more easily constructed than ‘hard’ metal tools and, because they are made from materials similar to the manufactured composite part, they can be made in-house and have a good co-efficient of thermal expansion match. However, as the ‘soft’ designation suggests, they are more vulnerable to wear and typically find application in relatively low-volume production. Additive manufacturing of thermoplastics has proven to be a lucrative option that can help improve the tooling functionalities, as it offers more design flexibility. Owing to the inherent nature of additive manufacturing, the possibility of printing sensors within the tool material and at proximity to otherwise inaccessible areas of the tool become a reality. Continuous carbon fiber (CCF)-reinforced three-dimensional (3D) printing of engineering thermoplastics has proven to be a viable option to strengthen a part well beyond the ideal moduli of unmodified thermoplastic. Furthermore, adding nanotubes or graphene to the thermoplastic matrix will also improve both the thermal conductivity and interlaminar shear strength within the tool. Carbon nanotubes (CNTs) and carbon fibers (CFs) are microwave susceptors; exploiting the physics of Joule heating to increase the energy efficiency of tool hardening and cure rates is a core goal of this project. Because of the rapid volumetric heating enabled by the absorption of microwave or radio frequency energy and electromagnetic (EM) annealing presents an attractive opportunity to significantly reduce manufacturing cycle times while improving part performance.

Craps, Matthew G.↗
DOE OSTI2023

Evaluation of Power Transmission Lines Hardening Scenarios Using a Machine Learning Approach

The power transmission infrastructure is vulnerable to extreme weather events, particularly hurricanes and tropical storms. A recent example is the damage caused by Hurricane Maria (H-Maria) in the archipelago of Puerto Rico in September 2017, where major failures in the transmission infrastructure led to a total blackout. Numerous studies have been conducted to examine strategies to strengthen the transmission system, including burying the power lines underground or increasing the frequency of tree trimming. However, few studies focus on the direct hardening of the transmission towers to accomplish an increase in resiliency. This machine learning-based study fills this need by analyzing three direct hardening scenarios and determining the effectiveness of these changes in the context of H-Maria. A methodology for estimating transmission tower damage is presented here in this study as well as an analysis of impact of replacing structures with a high failure rate with more resilient ones. We found the steel self-support-pole to be the best replacement option for the towers with high failure rate. Furthermore, the third hardening scenario, where all wooden poles were replaced, exhibited a maximum reduction in damaged towers in a single line of 66% while lowering the mean number of damaged towers per line by 10%.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

The combined effects of hydrogen and aging condition on the deformation and fracture behavior of a precipitation-hardened nickel-base superalloy

The effect of hydrogen (H) on the deformation behavior of Monel K-500 in various isothermal heat treatment conditions (non-aged, under-aged, peak-aged, and over-aged) was assessed via uniaxial mechanical testing. H-charged and non-charged specimens were strained to failure to facilitate a comparison of ductility, fracture surface morphology, strength, and work hardening behavior. For all examined heat treatment conditions, H charging leads to a significant reduction in ductility, which is accompanied by a consistent change in fracture surface morphology from ductile microvoid coalescence to brittle intergranular fracture. While H charging led to a systematic enhancement in the yield strength of all heat treatments, the three age-hardened conditions exhibited a more than 2-fold increase relative to the non-aged heat treatment. This suggests that H modifies the dislocation–precipitate interactions, which also manifest themselves through changes in work hardening metrics related to the dislocation storage and recovery rates. In particular, the H-charged peak-aged specimen exhibited a significant increase in initial hardening (dislocation storage) rate relative to the H-charged under-aged specimen. Transmission electron microscopy of these samples revealed the onset of widespread dislocation looping in the H-charged peak-aged sample, in addition to the planar slip bands characteristic of the non-charged condition. This result suggests that hydrogen induces the particle shearing-to-looping transition at smaller particle sizes. Possible mechanistic explanations for this observed behavior are presented.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Dynamic Strength and Equation of State of Epon 828 and Diethanolamine (DEA) Polymer Epoxy Under Shock Loading

Polymers are increasingly utilized in engineering applications that can experience high loading rates, necessitating increased understanding of their response under such conditions. The tamped Richtmyer-Meshkov Instability (RMI) method was used to characterize the equation of state and dynamic strength of the polymer Epon 828 cured with Diethanolamine (DEA). Plate impact experiments that drove a uniaxial shock compression wave across a sinusoidally corrugated metal-polymer interface were performed to generate shock stresses from 4-12 GPa and strain rates of approximately 1/s in the polymer. X-ray phase contrast imaging recorded the shock motion in the polymer and subsequent interface evolution. Analysis of this data yielded the polymer equation of state and, in conjunction with numerical modeling, the dynamic strength. The equation of state was validated against one-dimensional plate impact experiments from existing literature. The dynamic strength was compared to prior data for Epon 828 and related polymers at lower strain rates and found to exhibit significant strain rate and pressure-hardening effects. The strength of the Epon 828 polymer at 10 6 1/s was found to be approximately 1.5 GPa, suggesting that it is comparable to the strength of high strength metals at these dynamic conditions.

Equation of state↗
DOE OSTI2024

A high-order, localized-artificial-diffusivity method for Eulerian simulation of multi-material elastic-plastic deformation with strain hardening

A high-order method for Eulerian simulation of material undergoing large elastic–plastic deformation is developed. Thermodynamically consistent hyperelastic constitutive relations are assumed, facilitating the treatment of solids, liquids, and gases in a unified manner. Here, the method enables the simulation of multi-material interactions using a diffuse interface approach. Numerical capturing of material interfaces, shock waves, contact surfaces, and elastic-plastic strain discontinuities using high-order compact-difference schemes is assisted by Localized Artificial Diffusivity (LAD). In the new setting involving elastic–plastic deformation, the previously established terms for the artificial properties are verified to effectively regularize normal shocks. Additional LAD terms are introduced to the elastic and plastic kinematic equations to regularize shear shocks and other strain discontinuities, improving solution stability. Other important features of the method that improve robustness include the numerical treatment of compatibility terms in the kinematic equations, and the treatment of rotation. Particular emphasis is focused toward new advancements of the methods for plastic-deformation integration and the associated strain hardening of the material, including rate-dependent plasticity. The method is demonstrated on a variety of test problems, including 1-D impacts, a variant of the Shu-Osher problem, a Taylor impact, and a Richtmyer-Meshkov instability between two elastic–plastic solids with strain hardening.

42 ENGINEERING↗
DOE OSTI2022

What Can Plastic Flow Fields Tell Us About Heat Sources in Deformation Processing?

We characterize primary (shape-change) and secondary (friction) deformation, and associated temperature fields, in metal cutting and forming processes, using in situ imaging and simulation. The experimental configurations enable access to the deformation zones and die contact-interfaces, for measuring deformation, temperature, and frictional drag. Infra-red thermography reveals that the plastic strain-rate field is an excellent proxy for the deformation-induced heat sources. Both spatially confined and diffuse strain-rate fields occur, depending on the initial workpiece deformation state. When the strain rate is confined, as in pre-hardened material, the temperature modeling is much simplified, as the heat source is also now localized. However complex, microstructure-driven deformation modes, like sinuous flow in annealed metals, result in spatially diffuse strain-rate and body heat sources, more challenging to analyze. Furthermore, our unified measurements should be of value for accurately estimating the fraction of plastic dissipation that is converted into heat in large-strain deformation processes.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A Review of Computational Models for the Flow of Milled Biomass Part II: Continuum-Mechanics Models

The design of efficient material-handling systems for milled lignocellulosic biomass is challenging due to their complex particle morphologies and frictional interactions. Computational modeling, including the discrete element method (DEM) and continuum-based finite-element/volume methods, may offer scientific insight and predictive capabilities for the flow of milled biomass in hoppers and feeders. Herein, this article (Part II) presents a review of current state-of-the-art continuum models for the flow of milled biomass, whereas DEM models are reviewed in a companion article (Part I). Advances of numerical methods to solve the global governing equations are discussed first, followed by a comprehensive review of constitutive models for granular materials, including Drucker–Prager, hypoplastic, Cambridge-type, inertial-rheology, and nonlocal granular fluidity models. Specifically, we provide in-depth discussion on the suitability of those models for milled lignocellulosic biomass materials in terms of nonlinear elasticity, dependence of flow strength on pressure, density and shear rate, and compaction (dilation) associated with hardening (softening). Furthermore, our study shows that, despite the recent advances in continuum granular flow modeling, the most suitable constitutive models still need further development to account for material parametrization, multiflow regimes, and multiscale behavior before they can be reliably used to optimize the design and operation of biomass handling systems.

09 BIOMASS FUELS↗
DOE OSTI2020

Constitutive modeling of δ-phase zircaloy hydride based on strain rate dependent nanoindentation and nano-scale impact dataset

In this work, a constitutive model for zircaloy-4 embedded with δ-phase hydride rim/blister structures (δ-phase zircaloy hydride) is presented. Nanoindentation and nano-scale impact experiments were performed on the δ-hydride blisters as a function of temperature in order to obtain strain rate dependent location specific constitutive response. A power law viscoplastic constitutive model was chosen to represent the strain rate dependent behavior. The strength coefficient and the strain hardening exponent in the power law relation were found to decrease with increase in temperature indicating softening behavior at higher temperatures. The strain rate exponent remained constant with increase in temperature indicating that the rate dependent ductility does not change significantly at higher temperatures. A finite element method based model was created to analyze the failure behavior and the ductile to brittle transition in zircaloy hydride. The model predicted that fracture strength of δ-phase zircaloy hydride decreases linearly with increase in temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Dose and dose rate effects on the microstructural and mechanical stability of long-range ordered precipitates in Inconel 718

Nickel-based alloys offer exceptional mechanical properties and corrosion resistance for various applications in extreme environments such as high neutron flux, temperature, and stress. Precipitates, resulting from thermal treatments, increase the strength and creep resistance of these alloys. Here, heavy ion irradiation is shown to destabilize the γ' and γ" precipitates in Inconel 718 nickel-based alloy by disordering and dissolution processes. Transmission electron microscopy and atom probe tomography reveal that the disordering and dissolution rates of the precipitates are proportional to both irradiation dose and dose rate. Irradiation induced disordering occurs at a higher rate than the dissolution. From analyzing the hardening contributions, microscale mechanical results suggest radiation-induced disordering is responsible for the majority of the softening response at low dose. In addition, low dose radiation-induced disordering results in strain localization and is believed to be the primary cause for the drastic degradation of uniform elongation and toughness in irradiated Inconel 718.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A macro-micro approach for identifying crystal plasticity parameters for necking and failure in nickel-based alloy haynes 282

Here, this work develops a two-scales macro-micro approach to address the challenge in calibrating crystal plasticity microstructural models when samples undergo necking prior to fracture. The crystal plasticity models are crucial for predicting the materials’ plastic deformation and failure at the microstructure level, identifying the materials’ intrinsic properties as well as investigating the microstructure-properties relationships. However, after necking occurs, the experimentally measured stress-strain curves fail to reflect the materials ‘true’ stress-strain behavior and cannot be directly fitted into crystal plasticity models. The proposed macro-micro approach employs a top-down strategy to address this challenge, which has been studied with experimental tests on precipitation-strengthened Ni-based superalloy Haynes® 282®. In this approach, a macro rate-dependent anisotropic plasticity model with Voce-type hardening and Rice-Tracey damage law is first utilized to model the deformation and failure of the tensile bar, and calibrated by matching the stress-strain curves, necking strain, and reduction of area. Especially, to match the testing results under different applied strain rates, the rate-sensitivity parameter m and saturation stress in the elasticity model are modified to incorporate dependence on the local strain rate. Then, the ‘true’ stress-strain behaviors are extracted from the necking zone of the macro-model, which are used to calibrate a micro-model with explicit microstructures and governed by an extended crystal plasticity law. The consistency between the micro-model and macro-model are enforced during calibration. The calibration outcomes from the crystal plasticity model elucidate the materials intrinsic properties for slip, hardening, and failure, which is vital for further investigations into the microstructure-properties relationship and for accurate prediction of the material behavior under various test and service conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Spin and Accretion Rate Dependence of Black Hole X-Ray Spectra

We present a survey of how the spectral features of black hole X-ray binary systems depend on spin, accretion rate, viewing angle, and Fe abundance when predicted on the basis of first-principles physical calculations. The power-law component hardens with increasing spin. The thermal component strengthens with increasing accretion rate. The Compton bump is enhanced by higher accretion rate and lower spin. The Fe Kα equivalent width grows sublinearly with Fe abundance. Strikingly, the Kα profile is more sensitive to accretion rate than to spin because its radial surface brightness profile is relatively flat, and higher accretion rate extends the production region to smaller radii. The overall radiative efficiency is at least 30%–100% greater than as predicted by the Novikov–Thorne model.

79 ASTRONOMY AND ASTROPHYSICS↗