Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fractures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Fracture behavior of irradiation induced nanocrystalline UO 2 studied by in-situ mechanical testing in transmission electron microscopy

Uranium Dioxide (UO 2 ) is widely used as a fuel in current light water reactors (LWRs). Upon accumulation of radiation damage, LWR UO 2 fuel pellets start to develop a different microstructure at the pellet periphery when fuel burnup exceeds 45–50 GWd/tHM. The resulting porous, nanocrystalline microstructure is one of the most prominent microstructural changes occurring in such fuel. Its fracture mechanisms, which causes fuel fine fragmentation, could impact safety limits when the cladding breaches. Direct measurements of these properties are challenging, therefore a surrogate obtained via ion irradiation can be used. In this study, multiple microcantilevers were fabricated by focused ion beam from both fresh UO 2 and UO 2 irradiated with 84 MeV Xe 26+ ions to a peak dose of 1357 displacements per atom (dpa). Further, the irradiation produced a pseudo high burnup structure approximately 2 µm below the surface. In-situ nano-mechanical bending tests were conducted to investigate the fracture behavior and the effect of the surrogate UO 2 high burnup structure on local fracture properties. Fresh UO 2 fuel was observed to fracture in transgranular mode without nucleation or movement of dislocations. However, the Xe-irradiated nanocrystalline microcantilevers fractured along the grain boundaries, with no influence from the pre-existing micro-cracks in the microcantilever. Fracture toughness for this type of surrogate high burnup UO 2 structure is reported for the first time in literature. Both the fracture stress and toughness show degradation for UO 2 as a result of Xe-irradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Statistical fracture behavior of doped UO 2 using a ball-on-ring equibiaxial flexure test method

Metal oxide dopants, such as titanium and chromium oxides, have garnered considerable attention for their potential to increase grain size (≥ 30 µm) in UO 2 fuel, purportedly enhancing fission gas retention during reactor operation. Fuel performance is significantly impacted by fuel fracture behavior, so it is important to understand the effects of enhanced grain size and dopant content on UO 2 fuel fracture. UO 2 pellets were doped with 0.1 wt% TiO 2 and 0.3 wt% Cr 2 O 3 to alter density and grain size. Inductively coupled plasma mass spectroscopy measured dopant levels pre- and post-sintering. X-ray diffraction revealed lattice changes and microstrain via Rietveld refinement. Field emission scanning electron microscopy determined grain sizes of approximately 30 µm for TiO 2 doping and 7 µm for Cr 2 O 3 doping. Transverse rupture strength tests were performed on over 30 samples per dataset to obtain characteristic strength and Weibull modulus. Results indicate no statistical difference in fracture strength between 0.1 wt% TiO 2 doped UO 2 and undoped UO 2 , while 0.3 wt% Cr 2 O 3 doped UO 2 exhibited a 20% decrease in fracture strength. Doped UO 2 samples also showed reduced Weibull modulus compared to undoped UO 2 , suggesting increased scatter in fracture strength. This study's findings suggest that titanium and chromium oxide doping in UO 2 , regardless of grain size, induce residual stresses, decreasing fracture strength and increasing variability in fracture behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Influence of Pore Water on the Fracture of Silica Sand at Particle Scale

The fracture of particles has a significant influence on the engineering behavior of granular materials. There are no reported conclusive answers in the literature to explain the influence of pore water on the fracture of sand, gravel, railroad ballast rock, aggregates, rockfill, and so on. Here, in this paper, two novel techniques were adopted to investigate the influence of pore water on the fracture of natural silica sand at the particle scale. The three-dimensional (3D) synchrotron microcomputed tomography (SMT) imaging technique was used to acquire and analyze multiple 3D images of specimens composed of wetted silica sand that were subjected to confined one-dimensional (1D) compression loading up to the fracture stage. A few representative particles were identified and digitally separated from the liquid water and gas phases. The 3D SMT images offer clear experimental evidence of the phase transition of water from liquid to gas within the opening cracks. In addition, a computational fluid dynamics numerical simulation framework for water flow into an opening crack was adopted and the results show that the fast opening of the crack induced cavitation, water phase transition, and water hammer effects. The results of the numerical simulations agree with the confined 1D compression experiments where the onset of the bubbles (gas phase) within the crack is mainly generated during the secondary cavitation stage, and the generated bubble near the crack mouth opening resulted from the primary cavitation, which was directly caused by the crack expansion. The results reported in this paper present a new cavitation phenomenon that occurs during particle fracture, which offers a physics-based explanation of why water-wetted sand fractures at smaller stresses than dry and can pave the way for more in-depth future studies on the fracture of water-wetted sand.

cavitation↗
DOE OSTI2024

Mineral Deposition on the Rough Walls of a Fracture

Modeling carbonate growth in fractures and pores is important for understanding carbon sequestration in the environment or when supersaturated solutions are injected into rocks. Here, we study the simple but nontrivial problem of calcite growth on fractures with rough walls of the same mineral using kinetic Monte Carlo simulations of attachment and detachment of molecules and scaling approaches. First, we consider wedge-shaped fracture walls whose upper terraces are in the same low-energy planes and show that the valleys are slowly filled by the propagation of parallel monolayer steps in the wedge sides. The growth ceases when the walls reach these low-energy configurations so that a gap between the walls may not be filled. Second, we consider fracture walls with equally separated monolayer steps (vicinal surfaces with roughness below 1 nm) and show that growth by step propagation will eventually clog the fracture gap. In both cases, scaling approaches predict the times to attain the final configurations as a function of the initial geometry and the step-propagation velocity, which is set by the saturation index. The same reasoning applied to a random wall geometry shows that step propagation leads to lateral filling of surface valleys until the wall reaches the low-energy crystalline plane that has the smallest initial density of molecules. Thus, the final configurations of the fracture walls are much more sensitive to the crystallography than to the roughness or the local curvature. The framework developed here may be used to determine those configurations, the times to reach them, and the mass of deposited mineral. Effects of transport limitations are discussed when the fracture gap is significantly narrowed.

calcite↗
DOE OSTI2025

Wellbore Stability and Mud Loss Management in Geothermal Drilling: Optimizing Mud Weight to Mitigate Tensile Wellbore Fracturing at The Geysers, California

As part of a U.S. Department of Energy (DOE) Geothermal Technologies Office-funded initiative, Geysers Power Company, LLC, a subsidiary of Calpine Corporation, has been working to enhance drilling performance at the world’s largest geothermal field, The Geysers, in northern California. In a recent drilling operation of the GDC-36 well, excessive mud losses were encountered, initially addressed through repeated but largely ineffective cement plugging. Ultimately, the most effective strategy was to drill blind through the loss zones, made feasible by the high rate of penetration (ROP) achieved with PDC bits, allowing significant progress before the mud tanks were depleted and water-sensitive argillic formation layers could collapse. In response to these challenges, the project team explored alternative methods to minimize downtime and risks associated with cement plugging and continuous mud loss and to contemplate the driving mechanisms for the losses. Wellbore imaging using Formation MicroImager (FMI) and Ultrasonic Borehole Imager (UBI) tools revealed longitudinal tensile fractures, which were attributed to mud weights exceeding the minimum circumferential stress resulting from the native stress field and formation pressure. This study examines the mud losses encountered and leverages wellbore imaging data to understand the mechanisms behind mud induced tensile fracturing in specific rock facies. Understanding fracture behavior across different lithologies is crucial, as fractures within the reservoir can enhance steam migration throughout the system. The reservoir at The Geysers lies within the Mesozoic Franciscan Assemblage, a tectonic mélange formed by subduction. It consists of metamorphosed turbidite sandstone (greywacke) and mudstone (argillite), oceanic upper crust (including greenstone and chert), and serpentinized ultramafic rocks - each exhibiting distinct geomechanical fracturing properties. The structural fabric of the Franciscan Assemblage was shaped by low-angle Mesozoic thrust faulting and later overprinted by sub-vertical strike-slip structures related to the Pacific-North American plate boundary. A wellbore stability model was developed using core measurements and logs to simulate fracturing scenarios during drilling under varying stress conditions. These simulations guided the development of an optimized mud weight management strategy that should enable adaptive adjustments during drilling, reducing the likelihood of tensile fracturing and mud losses, ultimately improving operational efficiency.

15 GEOTHERMAL ENERGY↗
DOE OSTI2026

Aperture and roughness govern iron oxide passivation in olivine fractures during carbon mineralization

Efficient carbon dioxide mineralization in silicate-rich formations depends on reaction rates within fracture networks, yet the role of fracture microstructure remains poorly constrained. We investigated how fracture aperture and surface roughness influence mineralization by reacting synthetic forsteritic olivine fractures with controlled apertures (0.5–1.6 millimeters) and roughness (6–16 micrometers) with supercritical carbon dioxide at 13.7 megapascals and 185 degrees Celsius. Optical microscopy and Raman spectroscopy showed that rougher fracture surfaces promoted iron oxide precipitation, which passivated olivine surfaces, limiting magnesium availability for carbonate formation while removing iron as a reactant. These effects were more pronounced in smaller-aperture fractures. A geochemical model incorporating surface topography and passivation reproduced the observed trends, confirming that increased roughness can reduce reactivity despite greater surface area. Our results demonstrate that fracture microstructure strongly influences iron oxide passivation and carbon dioxide mineralization, with important implications for predicting long-term performance of engineered carbon dioxide storage systems.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Characterizing the impact of finite matrix block size on conservative particle transport through three-dimensional fracture networks

Mass transfer of solutes between fractures and the surrounding rock matrix exerts a noticeable signature on the tail of travel time distributions. When the width of the matrix is assumed to be infinite and advective transport through the fracture is sufficiently fast, the tails of the travel time distributions exhibit a classically expected slope of ψ(t) ∝ t -3/2 . However, studies have yet to characterize how solute transfer between fractures via diffusion through finite matrix blocks influences the tail’s slope in three-dimensional fractured media. Here, in this study, we assess the impact of finite matrix block size on breakthrough curve shape at different spatio-temporal scales by con ducting particle tracking simulations in three-dimensional discrete fracture networks. We consider a variety of hydrodynamic and geostructural proper ties to determine their relative impact on the resulting travel time distributions. We observe that the impact of matrix diffusion through a finite block on travel time distributions is similar to that of an infinite matrix block when the fracture spacing is sufficiently large, matrix diffusion is relatively weak, or transport is considered at an early control plane distance. We observe that the converse of these conditions, results in deviations from the classical ψ(t) ∝ t -3/2 scaling. These results provide a first step toward developing a metric to assess when finite block size effects are expected to significantly influence transport.

58 GEOSCIENCES↗
DOE OSTI2026

Fracture Intersections under Stress: Laboratory Data and Code [Data set]

The connectivity of natural and induced fractures governs the injection and withdrawal of fluids from subsurface reservoirs. Connectivity depends on intersections that control how fluids mix and move through the entire system. Here, we present data sets from 3D X-ray microscopy measurements of simple fracture networks under stress. 3D printing was used to create prismatic blocks that formed fracture networks composed of 2 orthogonal fractures. The network orientation was either "x" or "+" relative to an applied vertical stress. 3D data sets were collected for normal loads of 25, 100 and 200 Newtons for samples with fracture surfaces with either correlated or uncorrelated asperity distributions. The file contains data from the 12 samples analyzed along with an example code used to extract the intersection geometry. Additional experimental details can be found in the manuscript "Geologic Stress Modulates Fluid Mixing at Fracture Intersections" (10.1038/s43247-026-03525-9)and supplemental information to appear in Communications Earth & Environment in 2026.

02 PETROLEUM↗
DOE OSTI2024

Splitting tensile strength of shale cores: intact versus fractured and sealed with ureolysis-induced calcium carbonate precipitation (UICP)

Ureolysis-induced calcium carbonate precipitation (UICP) is a biomineral solution where the urease enzyme converts urea and calcium into calcium carbonate. The resulting biomineral can bridge gaps in fractured shale, reduce undesired fluid flow, limit fracture propagation, better store carbon dioxide, and potentially enhance well efficiency. The mechanical properties of shale cores were investigated using a modified Brazilian indirect tensile strength test. An investigation of intact shale using Eagle Ford and Wolfcamp cores was conducted at varying temperatures. Results show no significant difference between shale types (average tensile strength = 6.19 MPa). Eagle Ford displayed higher strength at elevated temperature, but temperature did not influence Wolfcamp. Comparatively, cores with a single, lengthwise heterogeneous fracture were sealed with UICP and further tested for tensile strength. UICP was delivered via a flow-through method which injected 20–30 sequential patterns of ureolytic microorganisms and UICP-promoting fluids into the fracture until permeability reduced by three orders of magnitude or with an immersion method which placed cores treated with guar gum and UICP-promoting fluids into a batch reactor, demonstrating that guar gum is a suitable inclusion and may reduce the number of flow-through injections required. Tensile results for both delivery methods were variable (0.15–8 MPa), and in some cores the biomineralized fracture split apart, possibly due to insufficient sealing and/or heterogeneity in the composite UICP-shale cores. Notably in other cores the biomineralized fracture remained intact, demonstrating more cohesion than the surrounding shale, indicating that UICP may produce a strong seal for subsurface application.

58 GEOSCIENCES↗
DOE OSTI2024

Impacts of irregularly-distributed acidified brine flow on geo-chemo-mechanical alteration in an artificial shale fracture under differential stress

The efficacy of geological carbon sequestration is reliant on the integrity of the caprock and its resistance to physical and chemical alteration. Caprocks with high abundance of reactive carbonates like calcite are susceptible to acid-promoted dissolution and can result in structural weakening. This work investigates the effect of acidified brine flow through an artificially fractured, high-carbonate (30 % by XRD) shale under differential compressive stress. Cylindrical samples were cut in half vertically and milled to create an artificial fracture with interlocking asperities and open channels. Samples were sheared with a single applied stress in a custom flow cell housed within an industrial CT scanner. Further, either acidic (pH 4) or reservoir-simulated (pH 9.5) brine was flowed through the artificial fracture for 7–8 days under reservoir pressure and room temperature. Model simulations indicate flow mainly occurred in open channels, with limited flow between overlapping asperities. Analysis of fracture surfaces by optical and scanning electron microscopy show increased surface alteration and roughness after exposure to pH 4 versus pH 9.5 brine indicating mineral dissolution/loss, and this effect is greater in areas that receive the highest brine flows. Similarly, surface analysis by scratch testing shows fracture toughness decreases more after exposure to acidic versus reservoir-simulated brine, with the greatest alteration in areas of highest acidic brine flows. Despite weakening, no shear slip occurred. Overall, the results indicate that acidified brine can result in significant physical and geomechanical alteration of irregular fracture surfaces in shale caprock, with greatest effects in preferential flow regions.

58 GEOSCIENCES↗
DOE OSTI2025

A phase-field fracture formulation for generalized standard materials: The interplay between thermomechanics and damage

Accurately modeling fracture of ductile materials poses open challenges in the field of computational mechanics due to the multiphysics nature of their failure processes. Integrating the interplay between thermodynamics and damage into ductile fracture models is vital for predicting critical failure modes. Here, in this paper, we develop a versatile phase-field (PF) framework for modeling ductile fracture, taking into account finite-strain elasto-plasticity. The framework stems from a variational formulation of constitutive relations for generalized standard materials (GSMs), whose response is described by a Helmholtz free energy and a dissipation pseudo-potential. Its variational structure is based on a minimum principle for a functional that expresses the sum of power densities for reversible and irreversible processes. By minimizing this functional with a constraint on a von Mises yield function, we derive the evolution equation for the equivalent plastic strain and an associative flow rule. This constrained optimization problem is analytically solved for a wide class of thermo-viscoplasticity models. The key innovations of the current work include (i) a cubic plastic degradation function that accounts for a non-vanishing damage-dependent yield stress, (ii) closed-form expressions of the Helmholtz free energy and dissipation pseudo-potential for three thermo-viscoplasticity models, (iii) an extended Johnson–Cook plasticity model with a nonlinear hardening law, and (iv) a plastic work heat source that depends on the plastic degradation function and a variable Taylor–Quinney (TQ) coefficient. The capabilities of the proposed framework are tested with the aid of four ductile fracture problems, including the Sandia Fracture Challenge. In each of these problems, we examine the evolution of relevant field variables such as the PF order parameter, the equivalent plastic strain, the temperature, and the internal power dissipation density, in addition to the overall structural response quantified by the force–displacement curve. These numerical studies demonstrate that the proposed framework effectively represents ductile fracture, yielding computational results that exhibit good agreement with experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Inference of phase field fracture models

The phase field approach to modeling fracture uses a diffuse damage field to represent cracks. This representation mollifies singularities that arise in computations with sharp interface models and some of the resultant difficulties in the mathematical and numerical treatment of fracture. Phase field fracture models have proven effective at representing crack propagation, branching, and merging. Specific formulations, beginning with brittle fracture, have also been shown to converge to classical solutions. Extensions to cover the range of material failure, including ductile and cohesive fracture, lead to an array of possible models. There exists a large body of literature focusing on this class of models and on the impact of model form on the predicted crack evolution. However, there have not been systematic studies into how optimal models may be chosen. Here, we take a first step in this direction by developing formal methods for identification of the best parsimonious model of phase field fracture given full-field data on the damage and deformation fields. We consider some of the main models that have been used for the degradation of elastic response due to damage and its propagation. Our approach builds upon Variational System Identification (VSI), a weak form variant of the Sparse Identification of Nonlinear Dynamics (SINDy). Furthermore, in this first communication we focus on synthetically generated data but we also consider central issues associated with the use of experimental full-field data, such as data sparsity and noise.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Complex Fluid‐Driven Fractures Caused by Crack‐Parallel Stress

Abstract Managing fluid‐driven fracture networks is crucial for subsurface resource utilization, yet the current understanding of the key controlling factors remains insufficient. While geologic discontinuities have been shown to significantly influence fracture network complexity, this study identifies another major contributor. We conducted a new set of experiments using a transparent true triaxial cell, which enabled video recording of the temporal evolution of fluid‐driven fracture paths. Using pseudo‐2D samples without macroscale structural discontinuities, we observed multiple occurrences of hydraulic fracture curving and branching under anisotropic boundary stresses. We proposed a theoretical model demonstrating that the stress parallel to the crack line in the solid matrix near the crack tip (i.e., the T ‐stress) accounts for the observed fracture curving behavior. This finding suggests that T ‐stress is an additional mechanism contributing to the complexity of fluid‐driven fracture networks in the subsurface, besides the geologic discontinuities.

58 GEOSCIENCES↗
DOE OSTI2025

Geochemical Impact of Acid Spearhead and Slickwater Stimulation on Wolfcamp Shale from the Hydraulic Fracturing Test Site

The Hydraulic Fracturing Test Site 1 (HFTS-1) was a field study performed in the Wolfcamp Formation in the West Texas Permian (Midland) Basin, USA, with a focus on improving the efficiency of hydraulic fracturing. Investigating site-specific rock-fluid geochemical interactions during hydraulic fracturing is an important step to understanding the impact on formation shale porosity, permeability, and long-term shale gas production. During field operations in this region, hydraulic fracturing fluid (HFF) injection usually starts with a concentrated acid spearhead for rapid rock dissolution, followed by the injection of near-neutral pH slickwater containing chemicals and proppants. A multistep sequential injection approach was used to investigate different stages of rock-fluid interactions. The carbonate content in the host rock is important when acid spearhead is considered, as carbonate mineral dissolution is rapid and can result in porosity and permeability changes in the shale matrix. Here, in this study, we designed flow-through experiments using fractured carbonate-rich and clay-rich Wolfcamp shale cores with (1) a short-time acid soaking step and (2) a long-term slickwater flow-through step to simulate the injection method used at HFTS-1. The fluid chemistry was analyzed. A thorough mineralogical progression [e.g., Calcium (Ca) dissolution and iron (Fe) redox progression] in the cores during HFF injection was also characterized and imaged by synchrotron microprobe. Reactive transport modeling was performed based on the experimental setup. The results showed that the acid spearhead is a crucial step in creating a reaction front by mineral dissolution, especially in carbonate-rich shales. A slight layer of ferrihydrite precipitated during the slickwater flow-through period. This study provides insights into potential geochemical impact due to hydraulic fracturing operations in the Permian Basin.

clastic rock↗
DOE OSTI2025

Fracture Network Quantification during CO2 Injection

This is the presentation prepared for the ARMA 2025 (59th US Rock Mechanics/Geomechanics Symposium) Conference held in Santa Fe, New Mexico, June 8-11, 2025. Accurate mapping and quantification of these networks are essential to ensure the integrity of CO2 storage reservoirs, understand and reduce potential leakage, and maintain long-term environmental safety. This study presents a novel machine learning-driven approach, integrated with geomechanical analysis, to quantify fracture networks and assess their spatial distribution during CO2 injection. This paper combines microseismic monitoring data with principles of hydraulic diffusivity and geomechanical analysis to characterize reservoir scale fracture network. The novelty of our approach lies in its capacity to assimilate time-dependent pressure data and microseismicity into a cohesive framework, which not only identifies microseismic triggering fronts but also tracks fracture distribution during active injection. Besides, leveraging image log data and analysis our approach also provides another angle of the insights to solidate the fracture networks understanding and geomechanical impacts. Key results from our study include the detection of over 100 distinct fracture clusters across the injection site, with fracture orientations strongly correlated with the prevailing in-situ stress field.

CO2 storage and sequestration↗
DOE OSTI2024

A multiphysics coupling framework for exascale simulation of fracture evolution in subsurface energy applications

Predicting the evolution of fractured media is challenging due to coupled thermal, hydrological, chemical and mechanical processes that occur over a broad range of spatial scales, from the microscopic pore scale to field scale. We present a software framework and scientific workflow that couples the pore scale flow and reactive transport simulator Chombo-Crunch with the field scale geomechanics solver in GEOS to simulate fracture evolution in subsurface fluid-rock systems. This new multiphysics coupling capability comprises several novel features. An HDF5 data schema for coupling fracture positions between the two codes is employed and leverages the coarse resolution of the GEOS mechanics solver which limits the size of data coupled, and is, thus, not taxed by data resulting from the high resolution pore scale Chombo-Crunch solver. The coupling framework requires tracking of both before and after coarse nodal positions in GEOS as well as the resolved embedded boundary in Chombo-Crunch. We accomplished this by developing an approach to geometry generation that tracks the fracture interface between the two different methodologies. The GEOS quadrilateral mesh is converted to triangles which are organized into bins and an accessible tree structure; the nodes are then mapped to the Chombo representation using a continuous signed distance function that determines locations inside, on and outside of the fracture boundary. The GEOS positions are retained in memory on the Chombo-Crunch side of the coupling. The time stepping cadence for coupled multiphysics processes of flow, transport, reactions and mechanics is stable and demonstrates temporal reach to experimental time scales. The approach is validated by demonstration of 9 days of simulated time of a core flood experiment with fracture aperture evolution due to invasion of carbonated brine in wellbore-cement and sandstone. We also demonstrate usage of exascale computing resources by simulating a high resolution version of the validation problem on OLCF Frontier.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Fracture Network Quantification during CO2 Injection

This is the conference paper accompanying an oral presentation at the ARMA 2025 (59th US Rock Mechanics/Geomechanics Symposium) Conference held in Santa Fe, New Mexico, June 8-11, 2025. Accurate mapping and quantification of these networks are essential to ensure the integrity of CO2 storage reservoirs, understand and reduce potential leakage, and maintain long-term environmental safety. This study presents a novel machine learning-driven approach, integrated with geomechanical analysis, to quantify fracture networks and assess their spatial distribution during CO2 injection. This paper combines microseismic monitoring data with principles of hydraulic diffusivity and geomechanical analysis to characterize reservoir scale fracture network. The novelty of our approach lies in its capacity to assimilate time-dependent pressure data and microseismicity into a cohesive framework, which not only identifies microseismic triggering fronts but also tracks fracture distribution during active injection. Besides, leveraging image log data and analysis our approach also provides another angle of the insights to solidate the fracture networks understanding and geomechanical impacts. Key results from our study include the detection of over 100 distinct fracture clusters across the injection site, with fracture orientations strongly correlated with the prevailing in-situ stress field.

CO2 storage and sequestration↗
DOE OSTI2024

Quartz Dissolution Effects on Flow Channelization and Transport Behavior in Three‐Dimensional Fracture Networks

We perform a set of reactive transport simulations in three-dimensional fracture networks to characterize the impact of geochemical reactions on flow channelization. Flow channelization, a frequently observed phenomenon in porous and fractured subsurface rock formations, results from the spatially variable hydraulic resistance offered by a geological structure. In addition to geo-structural features such as network connectivity, geometry, and hydraulic resistance, geochemical reactions, for example, dissolution and precipitation, can dynamically inhibit or enhance flow channelization. These geochemical processes can change the fracture permeability leading to increased flow channelization, which are localized connected regions of high volumetric flow rates that are seemingly ubiquitous in the subsurface. In our simulations, fractures partially filled with quartz are gradually dissolved until quasi-steady state conditions are obtained. We compare the flow field's initial unreacted and final dissolved states in terms of flow and transport observations. We observe that the dissolved fracture networks provide less resistance to flow and exhibit increased flow channelization when compared to their unreacted counterparts. However, there is substantial variability in the magnitude of these changes which implies that the channelization strongly depends on the network structure. In turn, we identify the interplay between the particular network structure and the impact of geochemical dissolution on flow channelization. The presented results indicate that geological systems that have been weathering or reactive for longer times in older landscapes are likely to have increased flow channelization compared to their equivalent but younger counterparts, which implies a time dependence on flow channelization in fractured media.

Hyman, Jeffrey D.↗