Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fiber composites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Recycling of natural fiber composites: Challenges and opportunities

Natural fibers have been widely used for reinforcing polymers attributed to their sustainable nature, excellent stiffness to weight ratio, biodegradability, and low cost compared with synthetic fibers like carbon or glass fibers. Thermoplastic composites offer an advantage of recyclability after their service life, but challenges and opportunities remain in the recycling of natural fiber reinforced polymer composites (NFRPCs). This article summarized the effects of reprocessing/recycling on the material properties of NFRPCs. The material properties considered include mechanical performance, thermal properties, hygroscopic behavior, viscoelasticity, degradation, and durability. NFRPCs can generally be recycled approximately 4–6 times until their thermomechanical properties change. After recycling 7 times, the tensile strength of NFRPCs can decrease by 17%, and the tensile modulus can decrease by 28%. The mitigation approaches to overcome degradation of material properties of NFRPCs such as adding functional additives and virgin plastics are also discussed. The main challenges in these approaches such as degradation and incompatibility are discussed, and an effort is made to provide a rationale for reprocessing/recyclability assessment. Finally, future applications of NFRPCs such as additive manufacturing and automotive part use are discussed.

36 MATERIALS SCIENCE↗
NASA NTRS1974

Investigation of fatigue strength of multilayer advanced fiber composites

The analytical characterization of a multilayer fiber composite plate (without hole) was accomplished for both static and dynamic loading conditions using the finite difference technique. Thornel 300/5208 composites with and without holes were subjected to static and tensile fatigue testing. Five (5) fiber orientations were submitted to test. Tensile fatigue testing also included three (3) loading conditions and two (2) frequencies. The low-cycle test specimens demonstrated a shorter tensile fatigue life than the high-cycle test specimens. Failure surfaces demonstrated effect of testing conditions. Secondary failure mechanisms, such as: delamination, fiber breakage, and edge fiber delamination were present. Longitudinal delamination between plies also occurred in these specimens.

Thornton, H. R.↗
NASA NTRS1985

Experimental evaluation of damping of graphite fiber composites

An investigation is described that was conducted to measure the damping of graphite fiber composites such as are to be used on the Hubble Space Telescope. The measurements were made on a composite cylinder under normal atmospheric conditions and in a vacuum chamber with varying thermal conditions. Such composites can outgas under vacuum conditions and this emission of trapped gases may have some influence on the material damping. Some results are presented for the damping coefficient measured under normal atmospheric conditions for a graphite fiber composite. The experimental damping data thus obtained were compared with the least square estimate obtained through a statistical analysis. The statistical analysis was based on a linear mathematical model consisting of a spring in parallel with a dashpot. It is observed that the discrepancy in the damping ratio between logarithmic decrement result and the least square fit is less than 6 percent for all the different tests made on the composite cylinder. Signal-to-noise ratio was maintained to be greater than 10.

Rao, M. D.↗
NASA NTRS1972

On fracture phenomena in advanced fiber composite materials.

The extension of linear elastic fracture mechanics (LEFM) from metallic alloys to advanced fiber composite laminates is considered. LEFM is shown to be valid for both isotropic and anisotropic homogeneous continua; the applicability of LEFM to advanced fiber composites is thus dependent on the validity of a homogeneous model of such materials. An experimental program to determine the validity of such a model for graphite/epoxy laminates is reviewed. Such laminates are found to have an apparent fracture toughness, from which it is inferred that a homogeneous material model is valid for the particular specimen geometry and composite laminates considered. Strain energy release rates are calculated from the experimentally determined fracture toughness of the various laminates. These strain energy release rates are found to lie in one of two groups, depending upon whether crack extension required fiber failure or matrix failure. The latter case is further investigated. It is concluded that matrix failure is governed by the tensile stress normal to the crack path.

Konish, H. J., Jr.↗
DOE OSTI2025

Enhanced Interfacial Strength in Carbon Fiber Composites via Mussel‐Inspired Sizing Polymers

Composite materials possess a high strength-to-weight ratio. A key determinant of their mechanical performance is the interfacial strength between the fibers and the matrix. Sizing agents are commonly used to improve this interface by promoting better adhesion, though optimizing this interaction remains a significant challenge. Here, this study evaluates the use of poly(catechol-styrene) (PCS), a mussel-inspired sizing agent, to enhance fiber–matrix bonding in carbon fiber composites. Woven carbon fiber laminates were dip-coated with varying concentrations of PCS (0.05 and 0.1 wt%) and subsequently fabricated using vacuum-assisted resin transfer molding followed by compression molding. Interlaminar shear strength (ILSS) tests showed improvements of 4% and 8% for the 0.05% and 0.1% PCS treatments, respectively. These results indicate that PCS is effective in reinforcing interfacial adhesion, thereby improving the mechanical integrity of carbon fiber-reinforced composites.

Carbon fiber composites↗
DOE OSTI2023

Enhanced through-thickness electrical conductivity and lightning strike damage response of interleaved vertically aligned short carbon fiber composites

Through-thickness electrical conductivity of carbon fiber reinforced polymers (CFRPs) is a key characteristic that determines the severity of lighting strike-induced damage. Carbon Fibers (CFs) are inherently electrically conductive and therefore provide high conductivity in the direction of the fiber orientation. However, electrical conductivities through the thickness and orthogonal to the CF orientation in CFRPs are governed by the insulating polymer matrix present between CFs. Here, in this work, through the thickness alignment of short CFs in between layers of CFRP laminates is demonstrated to improve the through-thickness electrical conductivity. Composites with interleaved vertically aligned short CF fibers (<150 μm) will be referred as V-fiber composites hereafter. The effect of the V-fiber on the lightning strike damage is evaluated against an artificial lightning strike of 100 kA (modified waveform A of SAE ARP-5412B standard). The improved through-thickness electrical conductivity of CFRP laminates (1.15 S/cm) through vertical alignment of short CFs was compared to reference CFRP laminates (0.13 S/cm) and was found to dissipate the artificial lightning strike current more efficiently. The surface damage after the artificial lightning strike in the V-fiber composites was reduced to 12.69 cm 2 compared to the reference CFRP surface damage of 57.67 cm 2 , a 78% reduction. It was also demonstrated that Joule heat generated due to lightning strike on the composites was significantly less than the reference sample using infrared (IR) thermography. A high retention (up to 78%) of flexural properties (modulus and strength) was observed in V-fiber composites post lightning strike impact as compared to only 47% retention in the reference panel.

42 ENGINEERING↗
NASA NTRS1995

Intercalated-Graphite-Fiber Composites

Electrically conducting composites made from bromine-intercalated graphite fibers in epoxy matrix. Bromine-intercalated graphite fibers have conductivity of about 20,000 ohm-1cm-1 and found to be stable in presence of moisture fibers even submerged for indefinite times) and at reasonably high temperature (200 degrees C). Conventional epoxy resins can be used with such fibers. Composite materials containing 50 percent bromine-intercalated graphite fibers have promising properties. Mechanical properties of composites similar to composites made with pristine fibers: Tensile and flexural strengths and Young's and bending moduli essentially unchanged, and interlaminar shear strengths slightly enhanced. Thermal conductivities of composites also show very little degradation. However, electrical conductivities of composites increase, which invites application of composites in electrical grounding planes and in shields against electro-magnetic interference.

Gaier, James R.↗
NASA NTRS1974

Advanced fiber-composite hybrids--A new structural material

Introduction of metal foil as part of matrix and fiber composite, or ""sandwich'', improves strength and stiffness for multidirectional loading, improves resistance to cyclic loading, and improves impact and erosion resistance of resultant fiber-composite hybrid structure.

Chamis, C. C.↗
NASA NTRS1996

An aeroelastic analysis of helicopter rotor blades incorporating piezoelectric fiber composite twist actuation

A simple aeroelastic analysis of a helicopter rotor blade incorporating embedded piezoelectric fiber composite, interdigitated electrode blade twist actuators is described. The analysis consist of a linear torsion and flapwise bending model coupled with a nonlinear ONERA based unsteady aerodynamics model. A modified Galerkin procedure is performed upon the rotor blade partial differential equations of motion to develop a system of ordinary differential equations suitable for numerical integration. The twist actuation responses for three conceptual full-scale blade designs with realistic constraints on blade mass are numerically evaluated using the analysis. Numerical results indicate that useful amplitudes of nonresonant elastic twist, on the order of one to two degrees, are achievable under one-g hovering flight conditions for interdigitated electrode poling configurations. Twist actuation for the interdigitated electrode blades is also compared with the twist actuation of a conventionally poled piezoelectric fiber composite blade. Elastic twist produced using the interdigitated electrode actuators was found to be four to five times larger than that obtained with the conventionally poled actuators.

Wilkie, W. Keats↗
NASA NTRS1996

Probabilistic Fiber Composite Micromechanics

Probabilistic composite micromechanics methods are developed that simulate expected uncertainties in unidirectional fiber composite properties. These methods are in the form of computational procedures using Monte Carlo simulation. The variables in which uncertainties are accounted for include constituent and void volume ratios, constituent elastic properties and strengths, and fiber misalignment. A graphite/epoxy unidirectional composite (ply) is studied to demonstrate fiber composite material property variations induced by random changes expected at the material micro level. Regression results are presented to show the relative correlation between predictor and response variables in the study. These computational procedures make possible a formal description of anticipated random processes at the intra-ply level, and the related effects of these on composite properties.

Stock, Thomas A.↗
NASA NTRS1973

A study of fracture phenomena in fiber composite laminates

The extension of linear elastic fracture mechanics from ostensibly homogeneous isotropic metallic alloys to heterogeneous anisotropic advanced fiber composites is considered. It is analytically demonstrated that the effects of material anisotropy do not alter the principal characteristics exhibited by a crack in an isotropic material. The heterogeneity of fiber composites is experimentally shown to have a negligible effect on the behavior of a sufficiently long crack. A method is proposed for predicting the fracture strengths of a large class of composite laminates; the values predicted by this method show good agreement with limited experimental data. The limits imposed by material heterogeneity are briefly discussed, and areas for further study are recommended.

Konish, H. J., Jr.↗
NASA NTRS1971

Analysis of multilayered fiber composites

Multilevel analysis computer program is useful in fiber matrix composites diagnosis, in structural syntheses of multilayered thornel/epoxy composite plates, in buckling studies of simply supported multilayered fiber composite plates, and in computing lamination residual stresses in angle ply composites.

Chamis, C. C.↗
NASA NTRS1985

Some features of the fabrication of multilayer fiber composites by explosive welding

The fabrication of multilayer fiber composites by explosive welding is characterized by intense plastic deformation of the matrix material as it fills the spaces between fibers and by high velocity of the collision between matrix layers due to acceleration in the channels between fibers. The plastic deformation of the matrix layers and fiber-matrix friction provide mechanical and thermal activation of the contact surfaces, which contributes to the formation of a bond. An important feature of the process is that the fiber-matrix adhesion strength can be varied over a wide range by varying the parameters of impulsive loading.

Kotov, V. A.↗
NASA NTRS1976

Failure mechanics of fiber composite notched charpy specimens

A finite element stress analysis was performed to determine the stress variation in the vicinity of the notch and far field of fiber composites Charpy specimens (ASTM Standard). NASTRAN was used for the finite element analysis assuming linear behavior and equivalent static load. The unidirectional composites investigated ranged from Thornel 75 Epoxy to S-Glass/Epoxy with the fiber direction parallel to the long dimension of the specimen. The results indicate a biaxial stress state exists in (1) the notch vicinity which is dominated by transverse tensile and interlaminar shear and (2) near the load application point which is dominated by transverse compression and interlaminar shear. The results also lead to the postulation of hypotheses for the predominant failure modes, the fracture initiation, and the fracture process. Finally, the results indicate that the notched Charpy test specimen is not suitable for assessing the impact resistance of nonmetallic fiber composites directly.

Chamis, C. C.↗
NASA NTRS1982

Multilevel optimum design of structures with fiber-composite stiffened-panel components

The multilevel approach to minimum weight structural design is extended to wing box structures with fiber-composite stiffened-panel components. Strength, deflection, and panel buckling constraints are treated at the system level with equivalent-thickness-type design variables. Local buckling and panel buckling constraints are guarded against at the component level, employing detailed component dimensions as design variables. A key feature of the method is selection of change in stiffness as the component level objective function to be minimized. Numerical results are given for wing box structures with sandwich and hat-stiffened fiber-composite panels.

Schmit, L. A.↗