Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fan performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Effects of tip clearance on overall performance of transonic fan stage with and without casing treatment

The overall performance of a transonic fan stage is presented for various tip clearances, with and without casing treatment. The stage was tested with a solid casing, and with open skewed slots and closed skewed slots in the casing over the rotor blade tips. Four nominal nonrotating rotor blade tip clearances from 0.061 to 0.178 centimeter were used. For all three casings, the pressure ratio and efficiency decreased with increasing tip clearance. The stall margin for a given casing also decreased with increasing clearance. At design speed and a given tip clearance, the highest stall margin was obtained with the open-slot casing, and the lowest stall margin was obtained with the solid casing.

Moore, R. D.↗
NASA NTRS1977

Variable pitch fan system for NASA/Navy research and technology aircraft

Preliminary design of a shaft driven, variable-pitch lift fan and lift-cruise fan was conducted for a V/STOL Research and Technology Aircraft. The lift fan and lift-cruise fan employed a common rotor of 157.5 cm diameter, 1.18 pressure ratio variable-pitch fan designed to operate at a rotor-tip speed of 284 mps. Fan performance maps were prepared and detailed aerodynamic characteristics were established. Cost/weight/risk trade studies were conducted for the blade and fan case. Structural sizing was conducted for major components and weights determined for both the lift and lift-cruise fans.

Ryan, W. P.↗
NASA NTRS2013

Effect of Two Advanced Noise Reduction Technologies on the Aerodynamic Performance of an Ultra High Bypass Ratio Fan

A wind tunnel experiment was conducted in the NASA Glenn Research Center anechoic 9- by 15-Foot Low-Speed Wind Tunnel to investigate two new advanced noise reduction technologies in support of the NASA Fundamental Aeronautics Program Subsonic Fixed Wing Project. The goal of the experiment was to demonstrate the noise reduction potential and effect on fan model performance of the two noise reduction technologies in a scale model Ultra-High Bypass turbofan at simulated takeoff and approach aircraft flight speeds. The two novel noise reduction technologies are called Over-the-Rotor acoustic treatment and Soft Vanes. Both technologies were aimed at modifying the local noise source mechanisms of the fan tip vortex/fan case interaction and the rotor wake-stator interaction. For the Over-the-Rotor acoustic treatment, two noise reduction configurations were investigated. The results showed that the two noise reduction technologies, Over-the-Rotor and Soft Vanes, were able to reduce the noise level of the fan model, but the Over-the-Rotor configurations had a significant negative impact on the fan aerodynamic performance; the loss in fan aerodynamic efficiency was between 2.75 to 8.75 percent, depending on configuration, compared to the conventional solid baseline fan case rubstrip also tested. Performance results with the Soft Vanes showed that there was no measurable change in the corrected fan thrust and a 1.8 percent loss in corrected stator vane thrust, which resulted in a total net thrust loss of approximately 0.5 percent compared with the baseline reference stator vane set.

Hughes, Christoper E.↗
NASA NTRS2005

Fan Noise Source Diagnostic Test: Rotor Alone Aerodynamic Performance Results

The aerodynamic performance of an isolated fan or rotor alone model was measured in the NASA Glenn Research Center 9- by 15- Foot Low Speed Wind Tunnel as part of the Fan Broadband Source Diagnostic Test conducted at NASA Glenn. The Source Diagnostic Test was conducted to identify the noise sources within a wind tunnel scale model of a turbofan engine and quantify their contribution to the overall system noise level. The fan was part of a 1/5th scale model representation of the bypass stage of a current technology turbofan engine. For the rotor alone testing, the fan and nacelle, including the inlet, external cowl, and fixed area fan exit nozzle, were modeled in the test hardware; the internal outlet guide vanes located behind the fan were removed. Without the outlet guide vanes, the velocity at the nozzle exit changes significantly, thereby affecting the fan performance. As part of the investigation, variations in the fan nozzle area were tested in order to match as closely as possible the rotor alone performance with the fan performance obtained with the outlet guide vanes installed. The fan operating performance was determined using fixed pressure/temperature combination rakes and the corrected weight flow. The performance results indicate that a suitable nozzle exit was achieved to be able to closely match the rotor alone and fan/outlet guide vane configuration performance on the sea level operating line. A small shift in the slope of the sea level operating line was measured, which resulted in a slightly higher rotor alone fan pressure ratio at take-off conditions, matched fan performance at cutback conditions, and a slightly lower rotor alone fan pressure ratio at approach conditions. However, the small differences in fan performance at all fan conditions were considered too small to affect the fan acoustic performance.

Hughes, Christopher E.↗
NASA NTRSDate not supplied

Performance Analysis of Optimized STARC-ABL Designs Across the Entire Mission Profile

Boundary layer ingestion (BLI) offers the potential for significant fuel burn reduction by exploiting strong aeropropulsive interactions. NASA’s STARC–ABL concept uses an electri- cally powered BLI tail cone thruster on what is otherwise a traditional airframe. Despite the traditional airframe of this configuration, aeropropulsive integration is critical to the perfor- mance of the BLI propulsor. Furthermore, due to being electrically powered, the fan pressure ratio and efficiency of the BLI tail cone thruster vary widely across the flight envelope, and this variation in fan performance must be accounted for with the aeropropulsive integration of the BLI system. Thus, accurate performance prediction for this novel propulsion configu- ration requires the use of a coupled aeropropulsive model across the flight envelope. In this work, we analyze the off-design performance of 18 optimized designs using an aeropropulsive model that is built with the OpenMDAO framework to couple 3-D RANS CFD simulations to 1-D thermodynamic cycle analyses. The designs are created via high-fidelity aeropropulsive design optimizations that span a range of fan pressure ratio and thrust values at the cruise conditions for the STARC-ABL concept, which was chosen as the aerodynamic design point for the propulsor. Performance analyses we present herein are then performed at a range of off-design flight conditions that span the flight envelope, including low-speed and low-altitude flight conditions. This study provides the first set of high-fidelity data for the STARC–ABL configuration at off-design conditions, and the results quantify the power savings through BLI compared to a traditional propulsion system across the entire mission profile.

optimization↗
NASA NTRS1998

Model Engine Performance Measurement From Force Balance Instrumentation

A large scale model representative of a low-noise, high bypass ratio turbofan engine was tested for acoustics and performance in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel. This test was part of NASA's continuing Advanced Subsonic Technology Noise Reduction Program. The low tip speed fan, nacelle, and an un-powered core passage (with core inlet guide vanes) were simulated. The fan blades and hub are mounted on a rotating thrust and torque balance. The nacelle, bypass duct stators, and core passage are attached to a six component force balance. The two balance forces, when corrected for internal pressure tares, measure the total thrust-minus-drag of the engine simulator. Corrected for scaling and other effects, it is basically the same force that the engine supports would feel, operating at similar conditions. A control volume is shown and discussed, identifying the various force components of the engine simulator thrust and definitions of net thrust. Several wind tunnel runs with nearly the same hardware installed are compared, to identify the repeatability of the measured thrust-minus-drag. Other wind tunnel runs, with hardware changes that affected fan performance, are compared to the baseline configuration, and the thrust and torque effects are shown. Finally, a thrust comparison between the force balance and nozzle gross thrust methods is shown, and both yield very similar results.

Jeracki, Robert J.↗
NASA NTRS1972

Fan noise and performance

Tradeoffs between aerodynamic and acoustic properties of various fan configurations led to the selection of a variety of fans that produce noise levels in the range of 100 to 120 PNdb. Fan configuration and design pressure ratio required for specific mission operations depend in part on the type of mission to be performed. Noise data obtained for single-stage low speed fans, single-stage high speed fans, and two-stage fan engines are presented in table form.

Kramer, J. J.↗
NASA NTRS2014

Doppler Lidar System Design via Interdisciplinary Design Concept at NASA Langley Research Center - Part II

Optimized designs of the Navigation Doppler Lidar (NDL) instrument for Autonomous Landing Hazard Avoidance Technology (ALHAT) were accomplished via Interdisciplinary Design Concept (IDEC) at NASA Langley Research Center during the summer of 2013. Three branches in the Engineering Directorate and three students were involved in this joint task through the NASA Langley Aerospace Research Summer Scholars (LARSS) Program. The Laser Remote Sensing Branch (LRSB), Mechanical Systems Branch (MSB), and Structural and Thermal Systems Branch (STSB) were engaged to achieve optimal designs through iterative and interactive collaborative design processes. A preliminary design iteration was able to reduce the power consumption, mass, and footprint by removing redundant components and replacing inefficient components with more efficient ones. A second design iteration reduced volume and mass by replacing bulky components with excessive performance with smaller components custom-designed for the power system. Thermal modeling software was used to run steady state thermal analyses, which were used to both validate the designs and recommend further changes. Analyses were run on each redesign, as well as the original system. Thermal Desktop was used to run trade studies to account for uncertainty and assumptions about fan performance and boundary conditions. The studies suggested that, even if the assumptions were significantly wrong, the redesigned systems would remain within operating temperature limits.

Crasner, Aaron I.↗
NASA NTRS1980

CF6 jet engine performance improvement: New fan

As part of the NASA sponsored engine component improvement program, and fan package was developed to reduce fuel consumption in current CF6 turbofan aircraft engine. The new fan package consist of an improved fan blade, reduced fan tip clearance due to a fan case stiffener, and a smooth fan casing tip shroud. CF6 engine performance and acoustic tests demonstrated the predicted 1.8% improvement in cruise sfc without an increase in engine noise. Power management thrust/fan speed characteristics were defined. Mechanical and structural integrity was demonstrated in model fan rotor photoelastic stress tests, full-size fan blade bench fatigue tests, and CF6 engine bird ingestion, crosswind, and cyclic endurance tests. The fan was certified in the CF6-500c2/E2 engines and is in commerical service on the Boeing 747-200, Douglas DC-10-30, and Atrbus industrie A300B aircraft.

Fasching, W. A.↗
NASA NTRSDate not supplied

New Capabilities and Improvements to the High-Order Glenn Flux Reconstruction Code

The Glenn Flux Reconstruction (GFR) code is a computational fluid dynamics (CFD) code under development at NASA Glenn Research Center. GFR is based on the high-order flux reconstruction (FR) method and provides a large-eddy simulation (LES) capability that is both accurate and efficient for complex aeropropulsion flows. Three significant new capabilities have been added to the code that improve its performance and functionality. First, a variety of explicit Runge-Kutta methods, including some with adaptive time stepping, were added to GFR with two methods offering a 33% improvement in time-to-solution. Second, GFR can now utilize fully unstructured, mixed-element meshes to more easily facilitate the grid generation process for complex geometries. Finally, a rotating reference frame capability has been added to GFR for solving rotating turbomachinery problems. A selection of results demonstrating these new capabilities are presented in this work. The Taylor-Green vortex problem is used to verify the new unstructured capability by showing similar accuracy and resolution for all element types. LES of the Turbulent Heat Flux Phase III (THX3) experiment with comparison to another high-order LES code and a popular Reynolds-averaged Navier-Stokes (RANS) code demonstrates the accuracy of the code for complex aeropropulsion flows. Finally, LES of a spacecraft cabin ventilation fan shows the ability of GFR to efficiently establish a fan performance map and identify operating points for further analysis at high orders of accuracy.

High-Order Methods↗
NASA NTRSDate not supplied

New Capabilities and Improvements to the High-Order Glenn Flux Reconstruction Code

The Glenn Flux Reconstruction (GFR) code is a computational fluid dynamics (CFD) code under development at NASA Glenn Research Center. GFR is based on the high-order flux reconstruction (FR) method and provides a large-eddy simulation (LES) capability that is both accurate and efficient for complex aeropropulsion flows. Three significant new capabilities have been added to the code that improve its performance and functionality. First, a variety of explicit Runge-Kutta methods, including some with adaptive time stepping, were added to GFR with two methods offering a 33% improvement in time-to-solution. Second, GFR can now utilize fully unstructured, mixed-element meshes to more easily facilitate the grid generation process for complex geometries. Finally, a rotating reference frame capability has been added to GFR for solving rotating turbomachinery problems. A selection of results demonstrating these new capabilities are presented in this work. The Taylor-Green vortex problem is used to verify the new unstructured capability by showing similar accuracy and resolution for all element types. LES of the Turbulent Heat Flux Phase III (THX3) experiment with comparison to another high-order LES code and a popular Reynolds-averaged Navier-Stokes (RANS) code demonstrates the accuracy of the code for complex aeropropulsion flows. Finally, LES of a spacecraft cabin ventilation fan shows the ability of GFR to efficiently establish a fan performance map and identify operating points for further analysis at high orders of accuracy.

Direct Numerical Simulations↗
NASA NTRS1972

Quiet engine design highlights

Three high performance fans were designed, built, and tested, accumulating 444 hours. All three fans are both aerodynamically and mechanically suitable for direct incorporation into engine applications. Two turbofan demonstrators to evaluate both low- and high-speed fan systems were also designed, built, and tested. All components and engine systems are demonstrating high reliability. These components have demonstrated advanced state-of-the-art in acoustics, aerodynamics, and mechanical design.

Koff, B. L.↗
NASA NTRS1977

Preliminary QCSEE program - Test results

Preliminary results are reported for the Quiet Clean Short-haul Experimental Engine (QCSEE) program initiated by NASA in 1974 to develop propulsion system technology suitable for powered-lift short-range commercial aircraft. The QCSEE technology also has applications to the proposed U.S. Navy V/STOL aircraft. Emphasis in the QCSEE program is placed on developing engines with low noise characteristics; in addition, the power plants are required to conform to EPA 1979 pollutant emissions standards. Thrust performance, fan design, and thrust/weight ratio are discussed for both the over-the-wing and under-the-wing engine configurations under study.

Ciepluch, C. C.↗
NASA NTRS1974

Quiet Clean Short-Haul Experimental Engine (QSCEE). Preliminary analyses and design report, volume 1

The experimental propulsion systems to be built and tested in the 'quiet, clean, short-haul experimental engine' program are presented. The flight propulsion systems are also presented. The following areas are discussed: acoustic design; emissions control; engine cycle and performance; fan aerodynamic design; variable-pitch actuation systems; fan rotor mechanical design; fan frame mechanical design; and reduction gear design.

Source record↗
NASA NTRS1982

Rotorcraft convertible engines for the 1980s

Two rotorcraft studies were executed. The goal was to identify attractive techniques for implementing convertible powerplants for the ABC, Folded Tilt Rotor, and X-wing type high speed, high-L/D rotorcraft; to determine the DOC and fuel savings benefits achieved thereby; and to define research required to bring these powerplants into existence by the 1990's. These studies are reviewed herein and the different methods of approach are pointed out as well as the key findings. Fan shaft engines using variable inlet guide vanes or torque converters, and turboprop powerplants appear attractive. Savings in DOC and fuel consumption of over 15 percent are predicted in some cases as a result of convertible engine use rather than using separate engines for the thrust and the shaft functions. Areas of required research are fan performance (including noise), integrated engine/rotorcraft control, torque converters, turbine design, airflow for rotorcraft torque control, bleed for lift flow, and transmissions and clutches.

Eisenberg, J. D.↗
NASA NTRS1999

Portable Fan Assembly for the International Space Station

NASA/ Marshall Space Flight Center (NASA/MSFC) is responsible for the design and fabrication of a Portable Fan Assembly (PFA) for the International Space Station (ISS). The PFA will be used to enhance ventilation inside the ISS modules as needed for crew comfort and for rack rotation. The PFA consists of the fan on-orbit replaceable unit (ORU) and two noise suppression packages (silencers). The fan ORU will have a mechanical interface with the Seat Track Equipment Anchor Assembly, in addition to the power supply module which includes a DC-DC converter, on/standby switch, speed control, power cable and connector. This paper provides a brief development history, including the criteria used for the fan, and a detailed description of the PFA operational configurations. Space Station requirements as well as fan performance characteristics are also discussed.

Jenkins, Arthur A.↗