Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “distributed manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Spray drop size and velocity measurements using the Phase/Doppler Particle Analyzer

Detailed measurements of the drop size and velocity distributions were obtained for a swirl chamber pressure atomizer. These data were obtained with the Phase/Doppler Particle Analyzer manufactured by Aerometrics, Inc. Direct measurements of the size distributions revealed the evolving characteristics of the spray. Size velocity correlations were used to evaluate the effect of velocity relaxation on the size distributions. The simultaneous measurement of drop size and velocity was of major importance in accurately describing the changes in the local drop size distributions and mass flux.

Bachalo, W. D.↗
NASA NTRS1991

Compressive testing of filament-wound cylinders

An experimental investigation has been conducted on the compressive buckling and failure of filament-wound circular cylinders. This investigation identifies one of the relationships between structural performance and scale, as well as some of the causes of reduced structural performance in large-scale structures. It is hypothesized that this effect is related to two conditions: first, the number of fiber tow undulations; and second, the percentage of weak interfaces within the structure. The effect of winding pattern and the resulting location of the fiber undulations were studied by varying the winding parameters. Three types of cylinders were manufactured from Amoco T650-35/1908 graphite/epoxy preimpregnated tow with different winding sequences (0/+/-60)s, (+/-30/90)s, and (90/+/-30)s. The (90/+/-30)s cylinders were manufactured with two different winding patterns (distributed and classical) and radius-to-thickness ratios (15 and 55). All cylinders were loaded in compression to failure. Comparisons of the compressive strength and failure modes demonstrate the relationship between the winding parameters, scale, and structural performance of filament-wound composite cylinders.

Jensen, David W.↗
NASA NTRS1994

Low-Flow-Rate Dry-Powder Feeder

Apparatus feeds small, precise flow of dry powder through laser beam of optical analyzer measuring patterns of light created by forward scattering (Fraunhofer diffraction) of laser beam from powder particles. From this optical measurement, statistical distribution of sizes of powder particles computed. Rates of flow optimized for measurement of particle-size distributions. Developed for analyzing particle-size distributions of solid-propellant powders. Also adapted to pharmaceutical industry, in manufacture of metal powder, and in other applications where particle-size distributions of materials used to control rates of chemical reactions and/or physical characteristics of processes.

Ramsey, Keith E.↗
NASA NTRS2003

Past, Present and Future Trends for NASA's EEE Parts Program

The foundation of NASA's Electrical, Electronic and Electromechanical (EEE) parts program is standardization. Standardization helps to reduce the number of unknown variables present as a project or program progresses; unknown variables equate to unknown risk. NASA spacecraft are usually 'one-offs' or at least part of a very short run, and every new part that is used represents a risk that has to be understood and mitigated as necessary. This equates directly to time and cost. Standardization of component parts is used to provide a foundation of known, dependable, qualified parts upon which a safe, reliable system can be built. In addition, the evaluation and selection of parts for the standard parts list unifies the activity under one group of experts rather than having engineers on each project overlapping and duplicating efforts. Thus, the project support engineers are able to concentrate on understanding and mitigating the risks for the non standard parts required to meet specific requirements of their project. Rapid technology change is producing conditions that make any form of parts-based standardization increasingly difficult, particularly the use of Commercial Off The Shelf (COTS) parts and assemblies. There are many complications to COTS-based standardization. COTS parts change rapidly and unpredictably, often have different characteristics fiom manufacturer to manufacturer, frequently are only available through distribution, have no universal specification and have variable and unpredictable radiation characteristics. This presentation will discuss some potential approaches to COTS parts standardization. Further into the future, in three to five years perhaps, the use of COTS boards and boxes will be extensive and standardization at these levels of assembly will be necessary. In five to ten years, most major spacecraft functions will probably be performed by COTS boards. How will this be achieved? What role will the parts engineer play, if any? This presentation will borrow from the lessons of the past to suggest some scenarios for the future.

Sampson, Michael J.↗
NASA NTRS1979

A distributed system adaptive control strategy

One attitude control device being studied for large spacecraft consists of two counter-rotating rings, each designated as an annular momentum control device (AMCD), that are attached to a spacecraft using several magnetic bearings distributed along the circumference of the rings. For large spacecraft large rings are desirable. Unfortunately, for large rings flexibility is appreciable and it becomes necessary to account for the distributed nature of the rings in the design of the magnetic bearing controllers. Also ring behavior is unpredictably sensitive to ring temperature, spin rate, manufacturing imperfections, and other variables. For that reason a distributed adaptive microcomputer-based control system is being sought for ring stabilization and maneuvering. An original adaptive-control methodology for distributed-parameter systems is detailed and application to spinning ring, i.e., AMCD, stabilization is used as an illustration. The proposed methodology, presented as a step-by-step procedure, combines a lumped-parameter expansion description of distributed parameter systems with a fundamental simultaneous identification and control strategy. Simulations are presented providing preliminary evidence of the capabilities of the proposed procedure.

Johnson, C. R., Jr.↗
NASA NTRS1994

Low-Flow-Rate Dry-Powder Feeder

Apparatus feeds small, precise flow of dry powder through laser beam of optical analyzer, measuring patterns of light created by forward scattering (Fraunhofer diffraction) of laser beam from powder particles. From measurement, statistical distribution of sizes of powder particles computed. Developed for analyzing particle-size distributions of solid-propellant powders. Also adapted to use in pharmaceutical industry, in manufacture of metal powder, and in other applications in which particle-size distributions of materials used to control rates of chemical reactions and/or physical characteristics of processes.

Ramsey, Keith E.↗
NASA NTRS2022

(Preliminary) Effects of Ball Milling Zeolite Powders for Use in Additively Manufactured Solid Sorbents

Zeolite 13X is favorable to be used as an adsorbent in carbon dioxide (CO2) removal from the spacecraft cabin air. Reducing the size of the zeolite particles and particle size distribution is thought to increase the capacity of CO2 adsorption of the zeolite 13X powder, and potentially increase its manufacturability as a paste for additive manufacturing or slip casting. This paper will go into detail on the process of using ball milling in order to reduce particle size and particle size distribution of commercial zeolite 13X powder, as well as to characterize CO2 adsorption and manufacturability of the milled powder. Both dry and wet ball milling was analyzed during the experiment. Studies were also ran on the amount of time the powder was milled, rotational speed of the milling machine, ball to powder ratio, ball to jar ratio, and ethanol to powder ratio. The processed powder was then characterized through laser diffraction, SEM, and surface measurement techniques to show that particle size and particle size distribution could be reduced, and to show the effect of the reduced particle size and particle size distribution on CO2 adsorption and manufacturability.

zeolite↗
DOE OSTI2024

Distribution Transformer Demand: Understanding Demand Segmentation, Drivers, and Management Through 2050

The National Renewable Energy Laboratory (NREL) has been working closely with the U.S. Department of Energy's Office of Electricity (OE) to understand the critical drivers and potential means of managing distribution transformer demand through 2050. This effort has consulted with utility representative organizations and transformer manufacturers to understand the problem, characterized the in-service assets, and modeled future demand. Distribution transformers, or service transformers, range from 10 to 5,000 kilovolt-amperes (kVA), have a high-side voltage of less than 34.5 kilovolts, and have step-down power delivery for customer end use. This research will help the manufacturing sector understand production requirements and better inform utility strategies for managing their demand.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS2004

Development of a Lunar Consumables Storage and Distribution Depot

NASA is in the preliminary planning stages for a future lunar base as a response to President George W. Bush's recent announcement of a new sustained exploration program beyond low earth orbit. Kennedy Space Center engineers are supporting this program by utilizing experience in Spaceport system design and operations to help develop a Lunar Consumables Depot. This depot will store propellants, life support fluids, and other consumables either transported from Earth or manufactured from In Situ resources. The depot will distribute these consumables in an energy efficient manner to end users including spacecraft, habitation modules, and rovers. This paper addresses some of the changes to lunar base architecture design as a result of advances in knowledge of lunar resources over the past 35 years, as well as technology advances in the area of In Situ Resource Utilization and consumable storage and distribution. A general system level description of the depot will be presented, including overall design philosophy and high level requirements. Finally, specific subsystem technologies that have been or will be developed by KSC will be addressed. Examples of these technologies are automated umbilicals, cryogenic refrigerators, novel storage vessels, advanced heat switches and heat exchangers, and self healing gaskets and wires.

Mueller, Robert P.↗
NASA NTRS1978

Progress on coal-derived fuels for aviation systems

Synthetic aviation kerosene (Syn. Jet-A), liquid methane (LCH4), and liquid hydrogen (LH2) appear to be the most promising coal-derived fuels. Liquid hydrogen aircraft configurations, their fuel systems, and their ground requirements at the airport are identified. These aircraft appear viable, particularly for long haul use, where aircraft fueled with coal derived LH2 would consume 9 percent less coal resources than would aircraft fueled with coal derived Syn. Jet-A. Distribution of hydrogen from the point of manufacture to airports may pose problems. Synthetic JET-A would appear to cause fewer concerns to the air transportation industry. Of the three candidate fuels, LCH4 is the most energy efficient to produce, and an aircraft fueled with coal derived LCH4 may provide both the most efficient utilization of coal resources and the least expensive ticket as well.

Witcofski, R. D.↗
NASA NTRS1944

Researches on the Piston Ring

In internal combustion engines, steam engines, air compressors, and so forth, the piston ring plays an important role. Especially, the recent development of Diesel engines which require a high compression pressure for their working, makes, nowadays, the packing action of the piston ring far more important than ever. Though a number of papers have been published in regard to researches on the problem of the piston ring, none has yet dealt with an exact measurement of pressure exerted on the cylinder wall at any given point of the ring. The only paper that can be traced on this subject so far is Mr. Nakagawa's report on the determination of the relative distribution of pressure on the cylinder wall, but the measuring method adopted therein appears to need further consideration. No exact idea has yet been obtained as to how the obturation of gas between the piston and cylinder, the frictional resistance of the piston, and the wear of the cylinder wall are affected by the intensity and the distribution of the radial pressure of the piston ring. Consequently, the author has endeavored, by employing an apparatus of his own invention, to get an exact determination of the pressure distribution of the piston ring. By means of a newly devised ring tester, to which piezoelectricity of quartz was applied, the distribution of the radial pressure of many sample rings on the market was accurately determined. Since many famous piston rings show very irregular pressure distribution, the author investigated and achieved a manufacturing process of the piston ring which will exert uniform pressure on the cylinder wall. Temperature effects on the configuration and on the mean spring power have also been studied. Further, the tests were performed to ascertain how the gas tightness of the piston ring may be affected by the number or spring power. The researches as to the frictional resistance between the piston ring and the cylinder wall were carried out, too. The procedure of study, and experiments conducted by the author, on this subject will be fully described in the following paragraphs.

Ehihara, Keikiti↗
NASA NTRS2017

Evaluation of a Variable Thickness Hybrid Composite Bull Gear

For several years, NASA Glenn Research Center and the U.S. Army Research Laboratory have been investigating hybrid (composite/steel) gear technology for use in vertical lift drive systems. The hybrid gear concept replaces the structural portion of a gear between the shaft and the gear rim with a lightweight carbon fiber composite, in an effort to reduce the overall weight of a gear and increase the drive system power density. Past research includes both small-scale and large-scale hybrid gear concepts, all of which have a constant composite thickness throughout. The design described in this paper is of a variable thickness, such that the composite is thickest at the inner diameter and this thickness is gradually reduced toward the outer diameter. The resulting "stair stepped" design stems from dropping plies of the braided carbon fiber prepreg composite fabric gradually with increased radius. Additionally, the interlock pattern at the inner metallic adapter was adjusted slightly from previous designs to obtain a better stress distribution on the inner metallic adapter. The manufactured variable thickness web was tested both in static torsion tests and operationally in a relevant gearbox environment. The results of these experiments will be presented and compared to a baseline steel configuration.

Gears; Drive Systems; Rotorcraft Propulsion;↗
NASA NTRS2018

Evaluation of a Variable Thickness Hybrid Composite Bull Gear

For several years, NASA Glenn Research Center and the U.S. Army Research Laboratory have been investigating hybrid (compositesteel) gear technology for use in vertical lift drive systems. The hybrid gear concept replaces the structural portion of a gear between the shaft and the gear rim with a lightweight carbon fiber composite, in an effort to reduce the overall weight of a gear and increase the drive system power density. An overview of the concept of the hybrid gear design is described in Ref. 1, 2, and 3. The research presented in these references includes both small-scale and large-scale hybrid gear concepts all of which have a constant composite thickness throughout. The design described in this paper is of a variable thickness, such that the composite is thickest at the inner diameter and this thickness is gradually reduced toward the outer diameter. The resulting stair stepped design stems from dropping plies of the braided carbon fiber composite fabric gradually with increased radius. Additionally, the interlock pattern at the inner metallic adapter was adjusted slightly from previous designs to obtain a better stress distribution on the inner metallic adapter. The manufactured variable thickness web was tested both in static torsion tests and operationally in a relevant gearbox environment. The results of these experiments will be presented and compared to a baseline steel configuration.

Rotorcraft Propulsion↗
NASA NTRS2020

A 3D Model to Predict Explicit Morphologies and Volume Fraction of Lack-of-Fusion Pores Generated in Selective Laser Melting Processes

The performance of an additively manufactured (AM) component is dependent on the distribution of process-induced defects in addition to the complex microstructure of the material, surface roughness of the component and the process-induced residual stresses. For instance, it has been well demonstrated that lack-of-fusion (LoF) pores produced in the selective laser melting (SLM) AM process can significantly limit the fatigue performance of the material. Although two-dimensional (2D) models exist to predict the 2D profiles of LoF pores, the 2D pore profiles cannot be directly inserted into a three-dimensional (3D) microstructure domain that is output from several prevailing process simulation packages. A few commercial packages that simulate the SLM process can predict LoF pores in a 3D domain, but the morphologies of LoF pores are voxelated and hence do not capture sharp corners of the pores, thereby obviating their use in fatigue crack initiation studies. In order to address the aforementioned gaps, a high-fidelity model that predicts not only the volume fraction, but also the explicit 3D morphologies and spatial distributions of LoF pores has been developed using a computer aided design-based environment. The model has been partially validated for Ti-6Al-4V alloy by comparing the predictions of the volume fraction of LoF pores predicted by the model with experimental data obtained from the literature. Absolute error in predicted volume fraction of LoF pores varied between 5.16% and 1.87% for energy density values between 13 J/mm3 and 45 J/mm3 where a significant amount (over 3% volume fraction) of LoF porosity was measured. The absolute error was within 1.87% for energy density values greater than 45 J/mm3.

Saikumar R. Yeratapally↗
NASA NTRSDate not supplied

Update on Planetary, Lunar, & Asteroid Natural Environment Testbed (PLANET)

At ISMSE15, the Planetary, Lunar, & Asteroid Natural Environment Testbed (PLANET) was introduced as an upcoming high-fidelity, combined-effects planetary surface environment laboratory. This year, we will present an update on the facility status, describing the procurement, installation, commissioning of the chamber in Huntsville, Alabama (USA). With NASA’s push to return to the Moon through the Artemis program, there is a clear need for more high-fidelity test chambers that can replicate multiple aspects of the lunar surface, especially the fine, dusty lunar soil known as regolith. The PLANET chamber is designed to fill this gap, enabling research & development, qualification, and verification testing in a combined lunar surface environment, at an affordable price, for government, commercial/industry, and academic partners. Features include a large regolith simulant bed, low energy electron and ion sources to replicate the solar wind, full-spectrum UV and Solar simulation, and a liquid nitrogen cryogenic shroud, all in a high-vacuum environment (as low as 10^-7 mbar). PLANET’s initial focus will be on the lunar environment, but other surface environments (Martian, asteroid, etc.) are also possible to simulate. Besides the environmental instrumentation, PLANET will be equipped with specialized test systems that the Space Environmental Effects Team has developed over the past two years, including an in-situ tribometer and uniform dust distribution system. The chamber is currently being manufactured, with plans to install in May 2024. This will be followed by outfitting and commissioning. The challenges and accomplishments seen during this process will be detailed, and data from the first tests performed in PLANET will be shared with the community.

environmental testing↗
DOE OSTI2025

Megawatt-Class, High-Voltage SiC Power Electronics Converters for Advanced Manufacturing with Grid Support Services

DE-EE0009135 aimed to push the 10kV SiC MOSFET based power electronics to 3-phase 13.8kV 10MW to be used as a Megawatt Class Medium-Voltage Power Conditioning Systems – PCS – to enable “Resilient Distribution through Grid-dispatching and Uninterrupted Quality Power to Manufacturing Facilities” during transitory grid disturbances. As a stretch to those goals, Eaton added the load power peak shaving opportunity.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Spatial distribution of sp 3 defects in carbon fibers via time-of-flight secondary ion mass spectrometry

Defects play a significant role in the material properties of carbon fibers (CF). Several defects result in the formation of sp 3 bonds in an otherwise sp 2 -dominant graphitic structure. Understanding the distribution of these defects within CF provides insight into their properties and the effect of manufacturing conditions. Reports showed time-of-flight secondary ion mass spectrometry (ToF-SIMS) is capable of characterizing the spatial distribution of sp 2 and sp 3 content in carbon materials. Here, ToF-SIMS was utilized to investigate the spatial distribution of sp 3 defects in T700, T1000, and M46 CF. M46 had the lowest sp 3 content. Center-to-edge analysis revealed that T700 CF had a gradient of sp 3 defects starting from the center and increasing to the edge, whereas M46 CF had a sudden increase in sp 3 defects roughly 1 μm from the edge. Comparatively, T1000 CF had a relatively uniform radial distribution of sp 3 defects, except for a newly identified sp 2 rich region at 0.8 μm from the center. This is hypothesized to originate from a skin–core structure that forms during CF manufacturing. As a result, this work demonstrates the utility of ToF-SIMS for characterizing the spatial distribution of sp 3 defects within CF, establishing new ways to understand CF formation.

Carbon fibers↗