SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
In continuous flow electrophoresis the axial flow structure changes from a fully developed rectilinear form to one characterized by meandering as power levels are increased. The origin of this meandering is postulated to lie in a hydrodynamic instability driven by axial (and possibly lateral) temperature gradients. Experiments done at MSFC show agreement with the theory.
Investigations have continued into the possibility that significant information on stream flow rates can be obtained from aerial and satellite imagery of river meander patterns by seeking a correlation between the meander and discharge spectra of rivers. Such a correlation could provide the basis for a simple and inexpensive technique for remote sensing of the water resources of large geographical areas, eliminating the need for much hydrologic recording. The investigation of the nature of the meander and discharge spectra and their interrelationship can also contribute to a more fundamental understanding of the processes of both river meander formation and drainage of large basins. It has been found that floods decay with an inverse power law dependence on time. The exponent of this dependence varies from river to river and even from station to station along the same river. This power law time dependence makes possible the forecasting of river discharge with an uncertainty of about 5% for as long as a month following the flood peak.
This study is concerned with the analytical solutions of natural convection flows in closed-end cylindrical vessels to obtain exact solutions of temperature and velocity distribution in the laminar flow region under steady state condition. The temperature and velocity distributions, in general power series of displacements, are substituted into the three basic equations of continuity, momentum and energy. The relationships between coefficients of all powers are obtained through initial and boundary conditions and recurrence formulae. For constant wall temperature conditions the general solution of temperature and velocity may be expressed as a function of displacement, geometry ratio and Rayleigh number. Prandtl number does not enter as an independent parameter.
In many applications, it is highly desirable to operate a CO2 laser in a sealed condition, for in an open system the laser requires a continuous flow of laser gas to remove the dissociation products that occur in the discharge zone of the laser, in order to maintain a stable power output. This adds to the operating cost of the laser, and in airborne or space applications, it also adds to the weight penalty of the laser. In a sealed CO2 laser, a small amount of CO2 gas is decomposed in the electrical discharge zone into corresponding quantities of CO and O2. As the laser continues to operate, the concentration of CO2 decreases, while the concentrations of CO and O2 correspondingly increase. The increasing concentration of O2 reduces laser power, because O2 scavenges electrons in the electrical discharge, thereby causing arcing in the electric discharge and a loss of the energetic electrons required to boost CO2 molecules to lasing energy levels. As a result, laser power decreases rapidly. The primary object of this invention is to provide a catalyst that, by composition of matter alone, contains chemisorbed water within and upon its structure. Such bound moisture renders the catalyst highly active and very long-lived, such that only a small quantity of it needs to be used with a CO2 laser under ambient operating conditions. This object is achieved by a catalyst that consists essentially of about 1 to 40 percent by weight of one or more platinum group metals (Pt, Pd, Rh, Ir, Ru, Os, Pt being preferred); about 1 to 90 percent by weight of one or more oxides of reducible metals having multiple valence states (such as Sn, Ti, Mn, Cu, and Ce, with SnO2 being preferred); and about 1 to 90 percent by weight of a compound that can bind water to its structure (such as silica gel, calcium chloride, magnesium sulfate, hydrated alumina, and magnesium perchlorate, with silica gel being preferred). Especially beneficial results are obtained when platinum is present in the catalyst composition in an amount of about 5 to 25 (especially 7) percent by weight, SnO2 is present in an amount of about 30 to 40 (especially 40) percent by weight, and silica gel is present in an amount of 45 to 55 (especially 50) percent by weight. The composition of this catalyst was suggested by preliminary experiments in which a Pt/SnO2 catalyst was needed for bound water to enhance its activity. These experimental results suggested that if the water were bound to the surface, this water would enhance and prolong catalyst activity for long time periods. Because the catalyst is to be exposed to a laser gas mixture, and because a CO2 laser can tolerate only a very small amount of moisture, a hygroscopic support for the catalyst would provide the needed H2O into the gas. Silica gel is considered to be superior because of its property to chemisorb water on its surface over a wide range of moisture content.
Sprays occur in a wide variety of industrial and power applications and in the processing of materials. A liquid spray is a phase flow with a gas as the continuous phase and a liquid as the dispersed phase (in the form of droplets or ligaments). Interactions between the two phases, which are coupled through exchanges of mass, momentum, and energy, can occur in different ways at different times and locations involving various thermal, mass, and fluid dynamic factors. An understanding of the flow, combustion, and thermal properties of a rapidly vaporizing spray requires careful modeling of the rate-controlling processes associated with the spray's turbulent transport, mixing, chemical kinetics, evaporation, and spreading rates, as well as other phenomena. In an attempt to advance the state-of-the-art in multidimensional numerical methods, we at the NASA Lewis Research Center extended our previous work on sprays to unstructured grids and parallel computing. LSPRAY, which was developed by M.S. Raju of Nyma, Inc., is designed to be massively parallel and could easily be coupled with any existing gas-phase flow and/or Monte Carlo probability density function (PDF) solver. The LSPRAY solver accommodates the use of an unstructured mesh with mixed triangular, quadrilateral, and/or tetrahedral elements in the gas-phase solvers. It is used specifically for fuel sprays within gas turbine combustors, but it has many other uses. The spray model used in LSPRAY provided favorable results when applied to stratified-charge rotary combustion (Wankel) engines and several other confined and unconfined spray flames. The source code will be available with the National Combustion Code (NCC) as a complete package.
Sprays occur in a wide variety of industrial and power applications and in materials processing. A liquid spray is a two-phase flow with a gas as the continuous phase and a liquid as the dispersed phase in the form of droplets or ligaments. The interactions between the two phases--which are coupled through exchanges of mass, momentum, and energy--can occur in different ways at disparate time and length scales involving various thermal, mass, and fluid dynamic factors. An understanding of the flow, combustion, and thermal properties of a rapidly vaporizing spray requires careful modeling of the ratecontrolling processes associated with turbulent transport, mixing, chemical kinetics, evaporation, and spreading rates of the spray, among many other factors. With the aim of developing an efficient solution procedure for use in multidimensional combustor modeling, researchers at the NASA Glenn Research Center have advanced the state-of-the-art in spray computations in several important ways.
Tensile and compressive flow behavior at various temperatures and strain rates, and tensile creep rupture behavior at 850 and 1050 C and various stresses were studied for (001)-oriented single crystals of the Ni-base superalloy PWA 1480. At temperatures up to 760 C, the flow stress is insensitive to strain rate and of greater magnitude in tension than in compression. At temperatures of 800 C and above, the flow stress decreases continuously with decreasing strain rate and the tension/compression anisotropy diminishes. The second stage creep rate and rupture time exhibited power law relationships with the applied stress for both 850 and 1050 C, however with different stress dependencies. The stress exponent for the steady state creep rate was about 7 at 1050 C, but much higher at 850 C, about 12. Directional coarsening of the gamma' phase occurred during creep at 1050 C, but not at 850 C.
Aerojet Rocketdyne's NextSTEP program is developing and demonstrating a 100 kW Electric Propulsion (EP) system, the XR-100, which includes a modular power processing unit and modular xenon feed system to operate a Nested Hall Thruster (NHT) designed for powers up to 200 kW. The NextSTEP system is intended for use on large scale cargo transportation to support human missions to the Moon and Mars, which require very high-power Solar Electric Propulsion (SEP) systems operating between 200 and 400 kW. The three-year program objective is to operate the integrated EP system continuously at 100 kW for 100 hours, advancing this very high-power EP system to Technology Readiness Level (TRL) 5. In order to process the power and control propellant flow for this high-power system, Aerojet Rocketdyne has developed a modular concept for the Power Processing Units (PPUs) and Xenon feed system. The program has completed testing of critical elements of the PPU and feed system with a thruster simulator. Design upgrades to demonstrate the TRL 5 capabilities are underway. This paper will present an overview of the program and system design approach, the high power XR-100 capabilities of the PPU and feed system, and the latest test results for the 100 kW EP system demonstration program. In order to successfully execute this contract, there is a close collaboration between the teammates at Aerojet Rocketdyne (AR), the University of Michigan (UM), the NASA Jet Propulsion Laboratory (JPL), and the NASA Glenn Research Center (GRC).
Aerojet Rocketdyne's NextSTEP program is developing and demonstrating a 100 kW Electric Propulsion (EP) system, the XR-100, which includes a modular power processing unit and modular xenon feed system to operate a Nested Hall Thruster (NHT) designed for powers up to 200 kW. The NextSTEP system is intended for use on large scale cargo transportation to support human missions to the Moon and Mars, which require very high-power Solar Electric Propulsion (SEP) systems operating between 200 and 400 kW. The three-year program objective is to operate the integrated EP system continuously at 100 kW for 100 hours, advancing this very high-power EP system to Technology Readiness Level (TRL) 5. In order to process the power and control propellant flow for this high-power system, Aerojet Rocketdyne has developed a modular concept for the Power Processing Units (PPUs) and Xenon feed system. The program has completed testing of critical elements of the PPU and feed system with a thruster simulator. Design upgrades to demonstrate the TRL 5 capabilities are underway. This paper will present an overview of the program and system design approach, the high power XR-100 capabilities of the PPU and feed system, and the latest test results for the 100 kW EP system demonstration program. In order to successfully execute this contract, there is a close collaboration between the teammates at Aerojet Rocketdyne (AR), the University of Michigan (UM), the NASA Jet Propulsion Laboratory (JPL), and the NASA Glenn Research Center (GRC).
IC printed-circuit board tester measures resistance as low as 0.1 ohm but uses little power. Two 4.7 kilohm resistors and connected transistors prevent current flow through operational amplifier until probe circuit is complete, eliminating need for on/off switch. Zener diode in series with amplifier output prevents audio oscillator operation until output has sufficient amplitude. Circuit utilizes 741 operational amplifier on 11.2 volt battery or lower voltage amplifiers.
Calculations of the thermal history of the moon were done by solving the thermal conductivity equation for the case in which the heat sources are the long lived radioactive elements Th, U, and K-40. The concentrations of these elements were adjusted to give 4 variations of heat flow. Calculations indicated that the moon's interior was heated to melting during the first 0.7 to 2.3 x 10 to the 9th power years. The maximum fusion involved practically the entire moon to a distance from 15 to 45 km beneath the surface, and started 3.5 to 4.0 x 10 to the 9th power years ago, or 2.5 x 3.0 x 10 to the 9th power years ago and continued for 1 to 2 x 10 to the 9th power years. The moon today is cooling. The current thickness of the solid crust is from 150 to 200 km and the heat flow exceeds the stationary value 1.5 fold.
Nutrient release in clinoptilolite-phosphate rock (Cp-PR) systems occurs through dissolution and cation-exchange reactions. Investigating the kinetics of these reactions expands our understanding of nutrient release processes. Research was conducted to model transport kinetics of nutrient release in Cp-PR systems. The objectives were to identify empirical models that best describe NH4, K, and P release and define diffusion-controlling processes. Materials included a Texas clinoptilolite (Cp) and North Carolina phosphate rock (PR). A continuous-flow thin-disk technique was used. Models evaluated included zero order, first order, second order, parabolic diffusion, simplified Elovich, Elovich, and power function. The power-function, Elovich, and parabolic-diffusion models adequately described NH4, K, and P release. The power-function model was preferred because of its simplicity. Models indicated nutrient release was diffusion controlled. Primary transport processes controlling nutrient release for the time span observed were probably the result of a combination of several interacting transport mechanisms.
ven with great advances in computational techniques and computing power during recent decades, the modeling of unsteady separated flows, such as those encountered in the wake of a re-entry vehicle, continues to be one of the most challenging problems in CFD. Of most interest to the aerothermodynamics community is accurately predicting transient heating loads on the base of a blunt body, which would result in reduced uncertainties and safety margins when designing a re-entry vehicle. However, the prediction of heat transfer can vary widely depending on the turbulence model employed. Therefore, selecting a turbulence model which realistically captures as much of the flow physics as possible will result in improved results. Reynolds Averaged Navier Stokes (RANS) models have become increasingly popular due to their good performance with attached flows, and the relatively quick turnaround time to obtain results. However, RANS methods cannot accurately simulate unsteady separated wake flows, and running direct numerical simulation (DNS) on such complex flows is currently too computationally expensive. Large Eddy Simulation (LES) techniques allow for the computation of the large eddies, which contain most of the Reynolds stress, while modeling the smaller (subgrid) eddies. This results in models which are more computationally expensive than RANS methods, but not as prohibitive as DNS. By complimenting an LES approach with a RANS model, a hybrid LES/RANS method resolves the larger turbulent scales away from surfaces with LES, and switches to a RANS model inside boundary layers. As pointed out by Bertin et al., this type of hybrid approach has shown a lot of promise for predicting turbulent flows, but work is needed to verify that these models work well in hypersonic flows. The very limited amounts of flight and experimental data available presents an additional challenge for researchers. Recently, a joint study by NASA and CUBRC has focused on collecting heat transfer data on the backshell of a scaled model of the Orion Multi-Purpose Crew Vehicle (MPCV). Heat augmentation effects due to the presence of cavities and RCS jet firings were also investigated. The high quality data produced by this effort presents a new set of data which can be used to assess the performance of CFD methods. In this work, a hybrid LES/RANS model developed at North Carolina State University (NCSU) is used to simulate several runs from these experiments, and evaluate the performance of high fidelity methods as compared to more typical RANS models. .
A Point Doppler Velocimeter (pDv) has been developed using a vapor-limited iodine cell as the sensing medium. The iodine cell is utilized to directly measure the Doppler shift frequency of laser light scattered from submicron particles suspended within a fluid flow. The measured Doppler shift can then be used to compute the velocity of the particles, and hence the fluid. Since this approach does not require resolution of scattered light from individual particles, the potential exists to obtain temporally continuous signals that could be uniformly sampled in the manner as a hot wire anemometer. This leads to the possibility of obtaining flow turbulence power spectra without the limitations of fringe-type laser velocimetry. The development program consisted of a methodical investigation of the technology coupled with the solution of practical engineering problems to produce a usable measurement system. The paper outlines this development along with the evaluation of the resulting system as compared to primary standards and other measurement technologies.
A NASA engineer received a heart transplant performed by Drs. DeBakey and Noon after suffering a serious heart attack. 6 months later that engineer returned to work at NASA determined to use space technology to help people with heart disease. A relationship between NASA and Drs. DeBakey and Noon was formed and the group worked to develop a low cost, low power implantable ventricular assist device (VAD). NASA patented the method to reduce pumping damage to red blood cells and the design of a continuous flow heart pump (#5,678,306 and #5,947,892). The technology and methodology were licensed exclusively to MicroMed Technology, Inc.. In late 1998 MicroMed received international quality and electronic certifications and began clinical trials in Europe. Ventricular assist devices were developed to bridge the gap between heart failure and transplant. Early devices were cumbersome, damaged red blood cells, and increased the risk of developing dangerous blood clots. Application emerged from NASA turbopump technology and computational fluid dynamics analysis capabilities. To develop the high performance required of the Space Shuttle main engines, NASA pushed the state of the art in the technology of turbopump design. NASA supercomputers and computational fluid dynamics software developed for use in the modeling analysis of fuel and oxidizer flow through rocket engines was used in the miniaturization and optimization of a very small heart pump. Approximately 5 million people worldwide suffer from chronic heart failure at a cost of 40 billion dollars In the US, more than 5000 people are on the transplant list and less than 3000 transplants are performed each year due to the lack of donors. The success of ventricular assist devices has led to an application as a therapeutic destination as well as a bridge to transplant. This success has been attributed to smaller size, improved efficiency, and reduced complications such as the formation of blood clots and infection.
A Hall Effect Thruster fueled by xenon was duration tested for7,198 hours at NASA’s Glenn Research Center.The thruster generated 1 million Newton-seconds of total impulse before the test was terminated voluntarily. Thrust, flow rate, and many other parameters were tracked continuously. Over 98.5% of the test was conducted at a single operating point, where the discharge power was 600 W, mean thrust was 39 mN and mean specific impulse was 1500 s. The shape of the discharge channel was measured via laser profilometery. The shape changed considerably over the course of the test, due to ion sputtering. However, the standard deviation of the thrust and specific impulse measurements at the nominal operating point was less than 1%. Evolution of the plasma plume was measured with a Faraday probe mounted upon a rotating arm. Plume divergence decreased over the course of the test
A flight test program was performed using the Boeing 757 flight research airplane to investigate the effect of noise from wing mounted engines on laminar boundary layer transition. An NLF glove was installed on the right wing panel just outboard of the engine. The extent of laminar flow on the glove was measured as a function of engine power setting for a range of flight conditions. A combination of surface and probe microphones was distributed over the upper and lower wing surfaces to measure sound spectra. The flight test program was completed in June 1985 and the results of preliminary analysis indicate that a maximum of about 29 percent of chord laminar flow was obtained on the upper surface and about 28 percent on the lower surface (at a high sideslip condition). The engine speed was varied from about 2600 (idle) to about 4500 (maximum continuous power) r/min. This produced changes in sound pressure level up to 20 dB on the lower surface. On the upper surface, the noise levels were independent of engine power but sensitive to airplane Mach number. No effect of engine power setting on upper surface transition location was observed, and only a small forward movement of the transition location on the lower surface was observed at the high power settings. Volume 1 of this report contains the program description and data analysis. Volume 2 is a compilation of all of the flight test data.
This volume (2 of 4) contains the specification, structured flow charts, and code listing for the protocol. The purpose of an autonomous power system on a spacecraft is to relieve humans from having to continuously monitor and control the generation, storage, and distribution of power in the craft. This implies that algorithms will have been developed to monitor and control the power system. The power system will contain computers on which the algorithms run. There should be one control computer system that makes the high level decisions and sends commands to and receive data from the other distributed computers. This will require a communications network and an efficient protocol by which the computers will communicate. One of the major requirements on the protocol is that it be real time because of the need to control the power elements.