Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “concurrent solutions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Plutonium reactive transport in fractured granite: Multi-species experiments and simulations

Plutonium (Pu) in the subsurface environment can transport in different oxidation states as an aqueous solute or as colloidal particles. The transport behavior of Pu is affected by the relative abundances of these species and can be difficult to predict when they simultaneously exist. This study investigates the concurrent transport of Pu intrinsic colloids, Pu(IV) (aq) and Pu(V-VI) (aq) through a combination of controlled experiments and semi-analytical dual-porosity transport modeling. Pu transport experiments were conducted in a fractured granite at high and low flow rates to elucidate sorption processes and their scaling behavior. In the experiments, Pu(IV) (aq) was the least mobile of the Pu species, Pu(V-VI) (aq) had intermediate mobility, and the colloidal Pu, which consisted mainly of precipitated and/or hydrolyzed Pu(IV), was the most mobile. The semi-analytical modeling revealed that the sorption of each Pu species was rate-limited, as the sorption could not be described by assuming local equilibrium in the experiments. The model was able to describe the sorption of the different Pu species that occurring either on fracture surfaces, in the pores of the rock matrix, or simultaneously in both locations. While equally good fits to the data could be achieved using any of these assumptions, a fracture-dominated process was considered to be the most plausible because it provided the most reasonable estimates of sorption rate constants. Importantly, a key result of this work is that the sorption rate constant of all Pu species tends to decrease with increasing time scales, which implies that Pu will tend to be more mobile at longer time scales than observations at shorter time scales suggest. This result has important implications for predicting the environmental impacts of Pu in the safety assessments of geologic repositories for radioactive waste disposal, and we explore potential mechanistic bases for upscaling the sorption rate constants to time and distance scales that cannot be practically evaluated in experiments.

58 GEOSCIENCES↗
DOE OSTI2020

Concurrently Approaching Volumetric and Specific Capacity Limits of Lithium Battery Cathodes via Conformal Pickering Emulsion Graphene Coatings

Abstract To achieve the high energy densities demanded by emerging technologies, lithium battery electrodes need to approach the volumetric and specific capacity limits of their electrochemically active constituents, which requires minimization of the inactive components of the electrode. However, a reduction in the percentage of inactive conductive additives limits charge transport within the battery electrode, which results in compromised electrochemical performance. Here, an electrode design that achieves efficient electron and lithium‐ion transport kinetics at exceptionally low conductive additive levels and industrially relevant active material areal loadings is introduced. Using a scalable Pickering emulsion approach, Ni‐rich LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA) cathode powders are conformally coated using only 0.5 wt% of solution‐processed graphene, resulting in an electrical conductivity that is comparable to 5 wt% carbon black. Moreover, the conformal graphene coating mitigates degradation at the cathode surface, thus providing improved electrochemical cycle life. The morphology of the electrodes also facilitates rapid lithium‐ion transport kinetics, which provides superlative rate capability. Overall, this electrode design concurrently approaches theoretical volumetric and specific capacity limits without tradeoffs in cycle life, rate capability, or active material areal loading.

Park, Kyu‐Young↗
DOE OSTI2025

Track reconstruction as a service for collider physics

Optimizing charged-particle track reconstruction algorithms is crucial for efficient event reconstruction in Large Hadron Collider (LHC) experiments due to their significant computational demands. Existing track reconstruction algorithms have been adapted to run on massively parallel coprocessors, such as graphics processing units (GPUs), to reduce processing time. Nevertheless, challenges remain in fully harnessing the computational capacity of coprocessors in a scalable and non-disruptive manner. This paper proposes an inference-as-a-service approach for particle tracking in high energy physics experiments. To evaluate the efficacy of this approach, two distinct tracking algorithms are tested: Patatrack, a rule-based algorithm, and Exa.TrkX, a machine learning-based algorithm. The as-a-service implementations show enhanced GPU utilization and can process requests from multiple CPU cores concurrently without increasing per-request latency. The impact of data transfer is minimal and insignificant compared to running on local coprocessors. This approach greatly improves the computational efficiency of charged particle tracking, providing a solution to the computing challenges anticipated in the High-Luminosity LHC era.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Improving Performance of M-to-N Processing and Data Redistribution in In Transit Analysis and Visualization

In an in transit setting, a parallel data producer, such as a numerical simulation, runs on one set of ranks M, while a data consumer, such as a parallel visualization application, runs on a different set of ranks N. One of the central challenges in this in transit setting is to determine the mapping of data from the set of M producer ranks to the set of N consumer ranks. This is a challenging problem for several reasons, such as the producer and consumer codes potentially having different scaling characteristics and different data models. The resulting mapping from M to N ranks can have a significant impact on aggregate application performance. In this work, we present an approach for performing this M-to-N mapping in a way that has broad applicability across a diversity of data producer and consumer applications. We evaluate its design and performance with a study that runs at high concurrency on a modern HPC platform. By leveraging design characteristics, which facilitate an “intelligent” mapping from M-to-N, we observe significant performance gains are possible in terms of several different metrics, including time-to-solution and amount of data moved.

Loring, Burlen↗
DOE OSTI2020

Improving Performance of M-to-N Processing and Data Redistribution in In Transit Analysis and Visualization

In an in transit setting, a parallel data producer, such as a numerical simulation, runs on one set of ranks M, while a data consumer, such as a parallel visualization application, runs on a different set of ranks N: One of the central challenges in this in transit setting is to determine the mapping of data from the set of M producer ranks to the set of N consumer ranks. This is a challenging problem for several reasons, such as the producer and consumer codes potentially having different scaling characteristics and different data models. The resulting mapping from M to N ranks can have a significant impact on aggregate application performance. In this work, we present an approach for performing this M-to-N mapping in a way that has broad applicability across a diversity of data producer and consumer applications. We evaluate its design and performance with a study that runs at high concurrency on a modern HPC platform. By leveraging design characteristics, which facilitate an ''intelligent'' mapping from M-to-N, we observe significant performance gains are possible in terms of several different metrics, including time-to-solution and amount of data moved.

Loring, Burlen↗
DOE OSTI2024

Bayesian calibration of stochastic agent based model via random forest

SAND2024-11403O The Bayesian Calibration of Stochastic Agent-based Model via Random Forest is a code that was developed in concurrence with an article by the same name that was written for a journal. The code reproduces simulation results and plots from the article. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525.

SciDAC↗
DOE OSTI2025

Using Apptainer in a Pilot-based Distributed Workload

GlideinWMS is a pilot and pressure-based workload manager for distributed scientific computing. Many experiments like CMS and Fermilab’s Neutrino experiments use it to provision elastic clusters for their analysis and simulations, split into close to a million concurrent jobs. Most user jobs require containers, and the pilots use Apptainer to set up the desired platform. For the pilots that run as regular batch jobs, Apptainer is safer, lighter, and easier to use than other containerization solutions. Many images used by the pilots are expanded SIF images distributed via the CernVM-FS: this combination is very efficient. At Fermilab, for example, we store on GitHub Dockerfiles that mimic the platform in the worker nodes of local clusters. GitHub workflows build and push the images to Docker Hub, and a service periodically pulls and converts them to the expanded SIF images in the CernVM-FS, so the scientists can find a familiar environment everywhere. Apptainer has also been used to run services inside the pilot jobs, like benchmarks that characterize the worker node being used, or a Triton Inference Server that allows sharing a GPU with all the jobs that run in parallel on a node.

Mambelli, Marco [Fermilab] (ORCID:0000000294892681↗
DOE OSTI2021

High-performance carbon nanotube electronic ratchets

The rapid advancements in low-power portable/wearable electronic devices require concurrent development of technologies that can provide power without the need for bulky, heavy battery storage. Electronic ratchets, asymmetric transistor-based devices that can convert AC signals or electronic noise into DC power, have been proposed as one solution to this growing need. Here, the recent demonstration of conjugated polymer-based electronic ratchets offers a route toward lightweight, flexible power sources for portable applications. Here we demonstrate the fabrication of the first electronic ratchets where the active channel component consists of semiconducting single-walled carbon nanotubes (s-SWCNTs), which can transform electronic noise or AC signals to a stable DC current with higher output power (up to ca. 14 mW for a chemically doped device) than their polymer-based analogs. We also show that patterning of the dopant profile in the s-SWCNT channel enables reasonable power conversion performance (ca. 3.5 mW) with improved stability relative to homogeneously doped devices. Our findings demonstrate the promise for s-SWCNT electronic ratchets as energy harvesting devices for portable, low-power applications.

ENGINEERING,MATERIALS SCIENCE,NANOSCIENCE AND NANO↗
DOE OSTI2021

The Application of Differential Scanning Calorimetry to Investigate Precipitation Behavior in Nickel-Base Superalloys Under Continuous Cooling and Heating Conditions

In this study, a suite of experimental tools and fast-acting, numerical-simulation techniques was used to quantify the precipitation behavior of three nickel-base superalloys: IN-100, LSHR, and 718. Experimental methods comprised differential scanning calorimetry (DSC) to establish the specific heat as a function of temperature and selected direct-resistance heating trials (using a Gleeble ® machine) to obtain samples for microstructural analysis. For the DSC experiments, each alloy was cooled at a prescribed constant rate (between 5 and 20 K/min) after an initial soak/equilibration in the high-temperature, single-phase (supersolvus) temperature regime. On-heating DSC trials beginning at ambient temperature were also performed on alloy 718 in three different starting conditions: super- δ -solvus solution treated and water quenched (denoted as ST), solution treated and aged (STA), and solution treated and overaged (STOA). DSC results, revealing the thermal signatures associated with the kinetics of precipitation of γ ' (IN-100, LSHR) or γ ' and γ " (718), were interpreted using a previously-developed fast-acting routine that treats concurrent nucleation, growth, coarsening, and dissolution. For these simulations, special attention was paid to various thermo-kinetic input parameters including equilibrium solvus-approach curves, bulk free energies of transformation, matrix-precipitate interface energies, and effective diffusivities. For the γ - γ ' superalloys (IN-100 and LSHR), estimates of precipitate volume fraction as a function of temperature from the specific-heat data revealed semi-quantitative agreement with simulation predictions. For the γ - γ '- γ " superalloy (718), simulation predictions of precipitate volume fractions were converted to specific heat as a function of temperature and showed semi-quantitative agreement with the direct measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2023

CRITICAL MINERAL RESOURCE ASSESSMENT OF COALS FROM THE POWDER RIVER BASIN, WYOMING, USA

Coal and associated sediments are potential sources of Rare Earth Elements (REE) and other critical minerals necessary for many consumer and defense-related products and development of energy technologies. For this study, 15 samples were sourced from Dry Fork Mine within the Powder River Basin near Gillette, Wyoming, to determine REE content along with select transition metals (t-metals) of interest in non-combusted coals and associated sediments. An excavator collected samples along a mine highwall, within benched intervals representing a foot to a few feet of coal strata. Homogenized sample subsets were crushed in an aluminum-ceramic vial, then passed through a 106-micron sieve. Sieved samples were pyrolyzed by a LECO TGA-108, which concurrently measured sample moisture, volatile, and ash content. Residual ash was then fused into a glass bead with lithium metaborate at a 6:1 Li-metaborate to sample ratio and then dissolved in 20% nitric acid. The nitric acid solutions containing digested beads were then diluted and passed through a 0.45 micron syringe filter. Filtered samples were analyzed by ICP-MS for REE and select t-metals. Reagent blanks were analyzed to assess for any potential contamination. Total REE plus Y (REE+Y) concentrations across the 15 samples range from 52 ppm to 1015 ppm with an average of 477 ppm on a dry ash basis. When normalized to upper continental crust (UCC; Taylor and McLennan, 1985) values, 13 of the 15 samples show average enrichment factors (EF) for REE+Y greater than 1. EF values indicate M-type enrichment (Sm through Er), as opposed to distinct preferential enrichment of light or heavy REE. T-metals with the highest average concentrations are V, Cu, Ni, and Zr at 215, 243, 123, and 118 ppm, respectively. Multiple t-metals had EF>1; however, Cu, Ge, and Sb have the highest average EF relative to UCC for t-metals, at 9.7, 8.0, and 17.0, respectively.

Copeland, Grant↗
DOE OSTI2025

A novel methodology for assessing the hygroscopicity of aerosol filter samples

Abstract. Due to US regulations, concentrations of hygroscopic inorganic sulfate and nitrate have declined in recent years, leading to an increased importance of the hygroscopic nature of organic matter (OM). The hygroscopicity of OM is poorly characterized because only a fraction of the multitude of organic compounds in the atmosphere is readily measured, and there is limited information on their hygroscopic behaviors. Hygroscopicity of aerosol is traditionally measured using a humidified tandem differential mobility analyzer (HTDMA) or electrodynamic balance (EDB). EDB measures water uptake by a single particle. For ambient and chamber studies, HTDMA measurements provide water uptake and particle size information but not chemical composition. To fill this information gap, we developed a novel methodology to assess the water uptake by particles collected on Teflon filters. This method uses the same filter sample for both hygroscopicity measurements and chemical characterization, thereby providing an opportunity to link the measured hygroscopicity with ambient particle composition. To test the method, hygroscopic measurements were conducted in the laboratory for ammonium sulfate, sodium chloride, glucose, and malonic acid, which were collected on 25 mm Teflon filters using an aerosol generator and sampler. Constant-humidity solutions (CHSs), including potassium chloride, barium chloride dihydrate, and potassium sulfate, were employed in a saturated form to maintain the relative humidity (RH) at approximately 84 %, 90 %, and 97 % in small chambers. Our preliminary experiments revealed that, without the pouch, water uptake measurements were not feasible due to rapid water loss during weighing. Additionally, we observed some absorption by the aluminum pouch itself. To account for this, concurrent measurements were conducted for both the loaded and the blank filters at each RH level. Thus, the dry loaded and blank Teflon filters were placed in aluminum pouches with one side open and in RH-controlled chambers for more than 24 h. The wet loaded samples and wet blanks were then weighed using an ultramicrobalance to determine the water uptake by the respective compound and the blank Teflon filter. The net amount of water absorbed by each compound was calculated by subtracting the water uptake of the blank filter from that of the wet loaded filter. Hygroscopic parameters, including the water-to-solute (W / S) ratio, molality, mass fraction solute (mfs), and growth factors (GFs), were calculated from the measurements. The results obtained are consistent with those reported by the Extended Aerosol Inorganics Model (E-AIM) and previous studies utilizing HTDMA and EDB for these compounds, highlighting the accuracy of this new methodology. This new approach enables the hygroscopicity and chemical composition of individual filter samples to be assessed so that in complex mixtures, such as chamber and ambient samples, the total water uptake can be parsed between the inorganic and organic components of the aerosol.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Development of a kinetic-thermodynamic model for lime-stabilization of Na-bentonite

This study presents the first kinetic model to predict the solid and pore solution composition of Na-bentonite clay reacting with slaked lime over a period of 720 days. The model successfully accounts for most experimental data using a single kinetic rate constant. The following sequence of reactions was predicted by the model: initial rapid dissolution of portlandite within the first 7 days, leading to a decrease in pH and dissolved calcium, and concurrent formation of calcium silicate hydrates (C-S-H: jennite), calcium aluminate hydrate (C-A-H: C₄AH₁₃), calcium aluminosilicate hydrates (stratlingite) and hydrotalcite. After 7 days, jennite and stratlingite are predicted to transform into tobermorite-II, contributing to strength development up to 28 days. From 28 to 90 days, continued montmorillonite dissolution is predicted, along with minor formation of ettringite, partial tobermorite-II dissolution, and precipitation of secondary phases such as albite and talc. Experimentally, portlandite dissolution was confirmed by TGA and XRD and found to be complete within 7 days, in agreement with model predictions. However, other predicted solid-phase transformations (e.g., tobermorite-II formation and dissolution, ettringite, albite, and talc formation) could not be conclusively verified through experimental techniques. Aqueous phase measurements confirmed that the pH and Ca trends in solution, and that equilibrium was reached by 90 days.

Chemical kinetics↗
DOE OSTI2025

Green Electrode Processing Enabled by Fluoro-Free Multifunctional Binders for Lithium-Ion Batteries

The eco-friendly processing of conjugated polymer binder for lithium-ion batteries demands improved polymer solubility by introducing functional moieties, while this strategy will concurrently sacrifice polymer conductivity. Employing the polyfluorene-based binder poly(2,7-9,9 (di(oxy-2,5,8-trioxadecane))fluorene) (PFO), soluble in water-ethanol mixtures, a novel approach is presented to solve this trade-off, which features integration of aqueous solution processing with subsequent controlled thermal-induced cleavage of solubilizing side chains, to produce hierarchically ordered structures (HOS). The thermal processing can enhance the intermolecular π–π stacking of polyfluorene backbone for better electrochemical performance. Notably, HOS-PFO demonstrated a substantial 6–7 orders of magnitude enhancement in electronic conductivity, showcasing its potential as a functional binder for lithium-ion batteries. As an illustration, HOS-PFO protected SiOx anodes, utilizing in situ side chain decomposition of PFO surrounding SiOx particles after aqueous processing are fabricated. HOS-PFO contributed to the stable cycling and high-capacity retention of practical SiOx anodes (3.0 mAh cm -2 ), without the use of any conducting carbon additives or fluorinated electrolyte additives. It is proposed that this technique represents a universal approach for fabricating electrodes with conjugated polymer binders from aqueous solutions without compromising conductivity.

25 ENERGY STORAGE↗
DOE OSTI2020

Extended use of face masks during the COVID-19 pandemic - Thermal conditioning and spray-on surface disinfection

The current COVID-19 pandemic has resulted in globally constrained supplies for face masks and personal protective equipment (PPE). Production capacity is limited in many countries and the future course of the pandemic will likely continue with shortages for high quality masks and PPE in the foreseeable future. Therefore, expectations are that mask reuse, extended wear and similar approaches will enhance the availability of personal protective measures. Repeated thermal disinfection could be an important option and likely easier implemented in some situations, at least on the small scale, than UV illumination, irradiation or hydrogen peroxide vapor exposure. In this paper, an overview on thermal responses and ongoing filtration performance of multiple face mask types is provided. Most masks have adequate material properties to survive a few cycles (i.e. 30 min disinfection steps) of thermal exposure in the 75°C regime. Some are more easily affected, as seen by the fusing of plastic liner or warping, given that preferred conditioning temperatures are near the softening point for some of the plastics and fibers used in these masks. Hence adequate temperature control is equally important. As guidance, disinfectants sprayed via dilute solutions maintain a surface presence over extended time at 25 and 37°C. Some spray-on alcohol-based solutions containing disinfectants were gently applied to the top surface of masks. Neither moderate thermal aging (less than 24 h at 80 and 95°C) nor gentle application of surface disinfectant sprays resulted in measurable loss of mask filter performance. Subject to bio-medical concurrence (additional checks for virus kill efficiency) and the use of low risk non-toxic disinfectants, such strategies, either individually or combined, by offering additional anti-viral properties or short term refreshing, may complement reuse options of professional masks or the now ubiquitous custom-made face masks with their often unknown filtration effectiveness.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High Thermoelectric Performance in the New Cubic Semiconductor AgSnSbSe 3 by High-Entropy Engineering

We investigate the structural and physical properties of the AgSn m SbSe m+2 system with m = 1-20 (i.e., SnSe matrix and ~5-50% AgSbSe 2 ) from atomic, nano, and macro length scales. We find the 50:50 composition, with m = 1 (i.e., AgSnSbSe 3 ), forms a stable cation-disordered cubic rock-salt p-type semiconductor with a special multi-peak electronic valence band structure. AgSnSbSe 3 has an intrinsically low lattice thermal conductivity of ~0.47 W m -1 K -1 at 673 K owing to the synergy of cation disorder, phonon anharmonicity, low phonon velocity, and low-frequency optical modes. Furthermore, Te alloying on Se sites creates a quinary high-entropy NaCl-type solid solution AgSnSbSe 3-x Te x with randomly disordered cations and anions. The extra point defects and lattice dislocations lead to glass-like lattice thermal conductivities of ~0.32 W m -1 K -1 at 723 K and higher hole carrier concentration than AgSnSbSe 3 . Concurrently, the Te alloying promotes greater convergence of the multiple valence band maxima in AgSnSbSe 1.5 Te 1.5 , the composition with the highest configurational entropy. Facilitated by these favorable modifications, we achieve a high average power factor of ~9.54 μW cm -1 K -2 (400-773 K), a peak thermoelectric figure of merit ZT of 1.14 at 723 K, and a high average ZT of ~1.0 over a wide temperature range of 400-773 K in AgSnSbSe 1.5 Te 1.5 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Laser Powder Directed Energy Deposition of Steels for Nuclear Applications

This comprehensive investigation examines the structure–property relationships in two nuclear alloy systems—Alloy 709 (A709) austenitic stainless steel and Grade 92 (G-92) ferritic/martensitic (F/M) steel—manufactured via directed energy deposition (DED) for sodium-cooled fast reactor applications. This study establishes the fundamental mechanisms for controlling microstructures for optimizing the mechanical performance of additively manufactured nuclear materials through systematic heat treatment optimization and multiscale characterization. As-deposited A709 steel develops a complex multiscale strengthening architecture consisting of a fine cellular solidification structure with diameter of 2-3 µm within10–50 µm grains, elevated dislocation densities from rapid thermal cycling, and grain boundary precipitates that activate concurrent Hall–Petch, dislocation, and precipitation hardening mechanisms to achieve exceptional properties [yield strength (YS): 603 MPa, ultimate tensile strength (UTS): 844 MPa, Vickers hardness: 220 HV] that achieve a 44% superior strength compared to that of the wrought material. Heat treatments produce different results. Solution annealing (SA) dissolves the cellular structure and reduces the hardness to 190 HV. Precipitation treatment (PT) keeps the cellular structure but adds carbides, allowing the hardness to reach 205 HV. The best approach combines both treatments (SA+PT) and creates uniform precipitate distributions with M 23 C 6 carbides at the grain boundaries and MX carbonitrides in the matrix, achieving a hardness of 195 HV. However, directional differences persist, with a 12%–15% strength variation between orientations due to the inherited layered microstructural architecture that survives aggressive heat treatment. While tensile testing at 550°C demonstrates 40%–50% thermal softening with dynamic strain aging, DED A709 steel still maintains a 71% higher YS than that of the wrought material. Ion irradiation studies (100–400 dpa) of DED A709 steel reveal progressive radiation damage with increasing void density and radiation-induced segregation causing nickel enrichment and chromium depletion, which will ultimately compromise mechanical properties. As-deposited G-92 exhibits exceptional strength (UTS: 1650–1700 MPa, 430 HV) through a complex microstructure containing both ferrite and martensite phases, a high geometrically necessary dislocation (GND) density (17.04×10 14 /m 2 ), and fine carbides. Heat treatments create distinct changes. Normalizing produces fresh martensite with the highest hardness (460 HV) and an increased GND density (20.23×10 14 /m 2 ). Tempering develops dual precipitation systems and reduces the hardness to 290 HV. The optimal approach uses sequential normalizing plus tempering, achieving balanced properties with the lowest hardness (250 HV) and a reduced GND density (11.01×10 14 /m 2 ). A processing-dependent anisotropy is observed: horizontal specimens achieve superior ductile behavior, while vertical specimens exhibit brittle failure. A tempering heat treatment successfully mitigates this anisotropic behavior by transforming the hard martensitic as-deposited structure into tempered martensite enabling both horizontal and vertical specimens to exhibit similar stress–strain characteristics with visible necking behavior. Remarkably, testing at 550°C reveals a reversal in the anisotropy, where as-deposited specimens achieve near isotropy with superior thermal stability (a 15%–20% strength reduction), while tempered specimens develop an orientation dependence with a 25%–30% strength reduction. Both alloy systems demonstrate that DED processing creates specimens with a superior strength through refined microstructural features, though with distinct strengthening mechanisms—austenitic through cellular structures and precipitates versus F/M through phase transformations and precipitates. Heat treatment optimization requires alloy-specific approaches, with A709 benefiting from controlled precipitation while G-92 requires careful phase transformation control. The results show that DED manufacturing can produce nuclear materials with exceptional performance, but directional effects and temperature-dependent behavior must be carefully considered for reactor component design and qualification.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Reinforced AEM Separators Based on Triblock Copolymers for Electrode-decoupled RFBs

Washington University in St. Louis (WUSTL), in collaboration with The University of Texas at San Antonio (UTSA) and Giner Inc. developed highly selective anion exchange membranes (AEMs) and a novel electrode-decoupled redox flow battery (RFB) for grid scale energy storage as part of the ARPA-E IONICS program (with connections to the DAYS program in the later part of the project). RFBs exhibit the crucial characteristic of system-level decoupled scaling of energy and power which makes them cost effective for the multi-GWh scales envisioned for grid-scale energy storage solutions. This has led to extensive (and deserved) research interest and attention. This project aimed to enhance the design space available for redox-flow batteries (RFBs) by enabling the long-term separation of disparate cationic (elemental) actives using a highly selective membrane separator, while concurrently permitting the transport of anions to balance charge. The approach proposed was to design and develop a highly selective anion-exchange membrane (AEM), which would in turn permit the design and development of electrode-decoupled RFBs. Pairs of (different element) cationic species with redox reactions exhibiting a large difference in their standard electrode potentials were identified to develop high voltage, high power RFBs while disrupting the existing paradigm of using a single element which can ionize to more than two soluble oxidation states (e.g.: Vanadium).

25 ENERGY STORAGE↗
DOE OSTI2024

ECP libraries and tools: An overview

The Exascale Computing Project (ECP) Software Technology and Co-Design teams addressed the growing complexities in high-performance computing (HPC) by developing scalable software libraries and tools that leverage exascale system capabilities. As we enter the exascale era, the need for reusable, optimized software solutions that can handle the unique challenges posed by these systems becomes increasingly important. The primary challenges the ECP teams faced were to create software libraries and tools that are performant on exascale architectures and portable and usable across diverse hardware platforms. Efforts addressed issues related to concurrent execution, memory management, and the integration of heterogeneous computing resources, such as GPUs from multiple vendors. The ECP’s strategy involved a structured development process encompassing the creation, optimization, and deployment of software in collaboration with industry, academia, and national laboratories. The project was organized into several technical areas: co-design of domain-specific suites with target applications, programming models and runtimes, development tools, mathematical libraries, data and visualization tools, and software ecosystem and delivery mechanisms. ECP has successfully developed a large portfolio of software libraries and tools that demonstrate significant improvements in performance and scalability on exascale systems. These products have been integrated into the Department of Energy’s computing facilities, supporting various scientific applications and ensuring robust performance across different hardware setups. ECP advancements in software development for exascale computing highlight the importance of a collaborative and adaptive approach to handling next-generation HPC systems complexities. The lessons learned emphasize the need for continuous engagement with end-users and vendors, and the importance of maintaining a balance between innovation and practical implementation. Future efforts will focus on ensuring scalability, keeping pace with rapid hardware advancements, and further enhancing the interoperability and usability of the software ecosystem. In conclusion, subsequent articles in this special issue provide in-depth discussions and case studies into specific library and tool efforts.

97 MATHEMATICS AND COMPUTING↗