SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Saddle clamp modified to prevent parts from falling off when installed or removed. Allows easy access for tightening or loosening bolts, and retains alignment with tube mounted in it when opened. All parts are held captive - bolts by retaining washers, floating nuts by pressing and swaging, and upper clamp band by tether. Upper and lower bolt flanges offset from each other to ensure access.
Testing of a 5.5 kV silicon (Si) diode and 5.8 kV prototype silicon carbide (SiC) diode in an inductive pulsed plasma thruster (IPPT) circuit was performed to obtain a comparison of the resulting circuit recapture efficiency,eta(sub r), defined as the percentage of the initial charge energy remaining on the capacitor bank after the diode interrupts the current. The diode was placed in a pulsed circuit in series with a silicon controlled rectifier (SCR) switch, and the voltages across different components and current waveforms were collected over a range of capacitor charge voltages. Reverse recovery parameters, including turn-off time and peak reverse recovery current, were measured and capacitor voltage waveforms were used to determine the recapture efficiency for each case. The Si fast recovery diode in the circuit was shown to yield a recapture efficiency of up to 20% for the conditions tested, while the SiC diode further increased recapture efficiency to nearly 30%. The data presented show that fast recovery diodes operate on a timescale that permits them to clamp the discharge quickly after the first half cycle, supporting the idea that diode-clamping in IPPT circuit reduces energy dissipation that occurs after the first half cycle
As part of the NASA Advanced Composites Project (ACP), a sub-element has been designed to provide validation data for progressive damage analysis models. The clamped tapered beam is a cross-ply laminated composite specimen designed to validate the simulation of the onset of matrix cracks and their interaction with delaminations, including delamination migration. A tapered geometry was used to localize the first damage occurrence in the tapered region, without prescribing an initial crack. The boundary and loading conditions were chosen to favor delamination growth and subsequent migration after the first damage occurrence. The typical sequence of events consists of a matrix crack located at the tapered region, leading to delamination onset, followed by delamination growth and subsequent delamination migration to a different interface via a dominant matrix crack. The Clamped Tapered Beam (CTB) was tested in both quasi-static and fatigue regimes. The results obtained are used in this study to assess and validate a methodology based on the Floating Node Method (FNM) implemented as an Extended Interface Element. In this methodology, quasi-static and fatigue damage formation and development are modeled by combining FNM to represent crack networks, with Directional Cohesive Zone Elements (DCZE) and Virtual Crack Closure Technique (VCCT), respectively. Qualitatively, the methodology is capable of predicting the sequence of events and overall failure morphology. Quantitatively, the simulation results generally bound the experimental data, based on the range of the characterization data used. In this paper, the results from quasi static and fatigue simulations are compared and correlated with experimental data.
Bellows restraints, thrust-vector attitude-control gimbal devices, and tube clamp descriptions
A theoretical analysis is given for the stresses and deflections of a square plate with clamped edges under normal pressure producing large deflections. Values of the bending stress and membrane stress at the center of the plate and at the midpoint of the edge are given for center deflections up to 1.9 times the plate thickness. The shape of the deflected surface is given for low pressures and for the highest pressure considered. Convergence of the solution is considered and it is estimated that the possible error is less than 2 percent. The results are compared with the only previous approximate analysis known to the author and agree within 5 percent. They are also shown to compare favorably with the known exact solutions for the long rectangular plate and the circular plate.
A fixture is described for making normal-pressure tests of flat plates 5 inches in diameter in which particular care was taken to obtain rigid clamping at the edges. Results are given for 19 plates, ranging in thickness from 0.015 to 0.072 inch. The center deflections and the extreme-fiber stresses at low pressures were found to agree with theoretical values; the center deflections at high pressures were 4 to 12 percent greater than the theoretical values. Empirical curves are derived of the pressure for the beginning of permanent set as a function of the dimensions of the plate and the tensile properties of the material.
Welding clamps, placed inside and outside a rocket case, hold it in proper alignment during tungsten inert gas welding. These metal blocks, connected by a stainless steel band, eliminate the need for backup bars.
The problem of buckling of clamped shallow spherical shells has recently been considered in several theoretical investigations. Buck-ling loads under uniform external pressure were obtained in these investigations which show a surprisingly good agreement with each other, but show a marked disagreement with available experimental values. In all previous studies it has been assumed that the shell deformations are rotationally symmetric. In this paper, the buckling problem is re-examined by introducing asymmetric modes of deformation. The approach is to superimpose small asymmetric deflections on finite axisymmetric deflections, and to show that the symmetric states of deformation are unstable over certain ranges of load and geometry parameter. Numerical results are obtained by means of a digital computer and are compared with previous theoretical and experimental results.
Jaw-type clamping tool inserts or removes objects in a hazardous environment. It has a strong, positive gripping force which is remotely operated by means of a wedge-screw mechanism.
Aluminum plate holds styrofoam securely in place for machining operations. The styrofoam is clamped to rubber or cork pads on the plate surface by vacuum. Foam rubber tape provides the vacuum seal.
Prebuckling deformation effects on clamped, thin- walled cylindrical shell buckling due to axial loading and internal pressure
Elastic stability of clamped shallow spherical shells under concentrated load, noting buckling modes
Elastic stability of clamped shallow spherical shells under concentrated load, noting buckling modes
Electrical connector clamp /bus bar/ gives high contact-surface efficiency for providing a high current to thin wall stainless steel tubing containing hydrogen gas. It uses lead solder film to provide the electrical equivalent of a fusion bond without degrading the grain structure, permitting disassembly and reuse of the components.
Vibration analysis of cylindrically curved panels with simply supported or clamped edges
Differential equation system for elastic equilibrium of hinge-clamped shallow spherical shell bounded by ellipse and rectangle
Quick acting clamp provides physical support for a closely confined detonating fuse in an application requiring removal and replacement at frequent intervals during test. It can be designed with a base of any required strength and configuration to permit the insertion of an object.
Computer analysis of clamped circular plate response to axisymmetric impulsive load