Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cavity optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

High current SRF cavity design for SPL and eRHIC

A high current five-cell Nb superconducting cavity, called BNL3 cavity, was optimized and designed for the SPL and eRHIC. For the fundamental mode, the optimization process aimed at maximizing the R/Q of the fundamental mode and the geometry factor G under an acceptable RF field ratio level of B{sub peak}/E{sub acc} and E{sub peak}/E{sub acc}. For higher order modes, the optimization is to lower (R/Q)Q{sub ext} for dipole and quadrupole modes to suppress the beam-break-up (BBU). To extract the HOM power out of the cavity, the BNL3 cavity employs a larger beam pipe, allowing the propagation of HOMs, but not the fundamental mode. Six HOM couplers (three at each end) are used to extract large HOM power. To avoid the cross-talk between cavities, tapers are employed between the cavities. This paper presents the design of the BNL3 cavity, end groups and BBU simulation results.

43 PARTICLE ACCELERATORS↗

Basic Electropolishing Process Research and Development in Support of Improved Reliable Performance SRF Cavities for the Future Accelerator

Future accelerators require unprecedented cavity performance, which is strongly influenced by interior surface nanosmoothness. Electropolishing is the technique of choice to be developed for high-field superconducting radiofrequency cavities. Electrochemical impedance spectroscopy (EIS) and related techniques point to the electropolishing mechanism of Nb in a sulfuric and hydrofluoric acid electrolyte of controlled by a compact surface salt film under F- diffusion-limited mass transport control. These and other findings are currently guiding a systematic characterization to form the basis for cavity process optimization, such as flowrate, electrolyte composition and temperature. This integrated analysis is expected to provide optimum EP parameter sets for a controlled, reproducible and uniform surface leveling for Nb SRF cavities.

43 PARTICLE ACCELERATORS↗

Modeling O and N Alloying in Nb for SRF Applications

N and O-alloyed superconducting radio frequency cavities exhibit extraordinary quality factors. Developing diffusion models that describe interstitial N and O in Nb is important for optimizing alloyed cavity quality factors and accelerating gradients. N and O-alloyed Nb samples are examined with SEM AND SIMS and their diffusion profiles modeled.

Lechner, Eric↗

Modeling the LLRF Control of a Multi-Cavity RF Station for Project-X

Fermilab’s High Intensity Neutrino Source (HINS), the 325 MHz low energy section of Project X consists of an RFQ, 18 copper cavities and a section of superconducting spoke resonator cavities, all driven by a single 2.5 MW klystron. Each cavity has a high power ferrite vector modulator which provides individual RF power control. This paper proposes a scheme that optimizes RF drive and vector modulator control. The different gradients, acceleration phase angles, unloaded Q’s and beam loading are taken into account to optimize the cavities detuning angles, forward power, and loaded Q’s. This scheme makes an efficient use of the klystron’s high bandwidth ability to modulate the forward power, hence minimizing the burden on the high power vector modulator during the RF pulse. The proposed method is explained in details, a parameter sensitivity analysis is performed and the impact on the total power consumption for the RF station is calculated.

Branlard, J.↗

DEMONSTRATION OF TWICE REDUCED LORENTZ FORCE DETUNING IN SRF CAVITY BY COPPER COLD SPRAYING

Superconducting RF (SRF) cavities usually are made of thin-wall high RRR Niobium that is susceptible to Lorentz Force Detuning (LFD) ? cavity deformation phenomena caused by high magnitude RF fields. This type of deformation can be mitigated by using an additional copper layer deposited on the outer surface of the cavity. In this paper, we present both modeling results and experimental data of high gradient test of an SRF cavity at cryogenic temperatures. It was demonstrated that LFD can be significantly reduced (factor of two) by the copper cold spray reinforcement without sacrificing cavity flexibility for tuning. We also present a finite-element model that allows us to confirm our experimental results and optimize the cavity geometry for LFD reduction with incorporated coupled RF, structural and thermal modules.

Kostin, R.↗

High Brightness Room Temperature III-Nitride Based Single Photon Source

Single photon sources (SPS) are quantum light sources where photons are emitted one at a time instead of randomly (e.g. lasers) or in a bunch (e.g. thermal) that can significantly impact quantum information science (computing and secure communications) and quantum metrology. Some highly desirable features of SPS are low second order correlation (g 2 ),controllable emission, electrically injected room temperature operation with high photon rate, high extraction efficiency and controllable directionality. Approaches taken thus far using different material systems have only addressed a subset of these features. III-nitride based approach offers a clear pathway to deterministic, room temperature (R.T.), electrically injected practical SPS as one can potentially also leverage the knowledge and technology from the light emitting diode (LED) world. Here we will describe a hybrid approach wherein a TiO2 based photonic crystal (PC) cavity is fabricated around an InGaN quantum dot (QD) embedded nanoscale post deterministically placed inside a photonic crystal cavity. This project takes the initial steps necessary to achieve a practical, compact SPS. We have used finite difference time domain simulations to optimize the cavity design to achieve high quality factor, mode overlap with QD and high extraction. We have fabricated InGaN quantum dots using a top-down approach involving dry etch and photoelectrochemical etch followed by electron beam lithography based nanofabrication of photonic crystal cavities.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An Advanced simulation Code for Modeling Inductive Output Tubes

During the Phase I program, CCR completed several major building blocks for a 3D large signal, inductive output tube (IOT) code using modern computer language and programming techniques. These included a 3D, Helmholtz, time-harmonic, field solver with a fully functional graphical user interface (GUI), automeshing and adaptivity. Other building blocks included the improved electrostatic Poisson solver with temporal boundary conditions to provide temporal fields for the time-stepping particle pusher as well as the self electric field caused by time-varying space charge. The magnetostatic field solver was also updated to solve for the self magnetic field caused by time changing current density in the output cavity gap. The goal function to optimize an IOT cavity was also formulated, and the optimization methodologies were investigated.

43 PARTICLE ACCELERATORS↗

Toward Qualifications of HB and LB 650 MHz Cavities for the Prototype Cryomodules for the PIP-II Project

High-beta (HB) and low-beta (LB) 650 MHz cryomodules are key components of the Proton Improvement Plan II (PIP-II) project. In this contribution we present the results of several 5-cell HB650 cavities that have been processed and tested with the purpose of qualifying them for the prototype cryomodule assembly, which will take place later this year. We also present the first results obtained in LB650 single-cell cavities process optimization. Taking advantage of their very similar geometry, we are also analyzing the effect of different surface treatments in FRIB’s 5-cell medium-beta 644MHz cavities. Cavities processed with N-doping and mid-T baking showed very promising results in term of both Q-factors and accelerating gradient for these low-beta structures.

43 PARTICLE ACCELERATORS↗

Comparing Exciton-Polariton Couplings in Two-Dimensional MoS2 Cavities

Exciton-polaritons (EPs) are an emerging approach to achieve strong light-matter coupling and robust quantum phenomena, with application to areas such as photonic neuromorphic computing for instance reservoir computing. 2D transition metal dichalcogenides (TMDs) are promising candidates to host EPs due to their potential for strong coupling as evidenced by large Rabi splitting energies, which in the case of few-layer MoS2 has been demonstrated to reach 293 meV when coupled to the C exciton, placing it in the ultrastrong coupling regime, at room temperature. Here we examine how the Rabi splitting of CVD-grown monolayer MoS2 in a cavity can be optimized by tuning two variables: cavity geometry (thickness of silver and dielectric spacers) and the targeted exciton for coupling (A at about 1.9 eV, B at about 2.06 eV, or C at about 2.9 eV). With the cavity geometry, there is a tradeoff between optical field confinement and transmission. With the targeted exciton, there may be a tradeoff between Rabi splitting and lifetime. Transfer matrix simulations are used to inform how thick the cavity layers need to be, and at what angle measurements should be performed, to achieve Rabi splitting at a certain exciton energy. Experimentally, the Rabi splitting is measured by placing the cavity at a specified angle and measuring the optical reflectance and transmittance. By fitting the data, we find Rabi splittings of 124 meV, 194 meV, and 288 meV for the A, B, and C excitons, respectively, which places them in the strong, and on the edge of the ultrastrong, coupling regime.

exciton-polaritons↗

Optimizing the quality factor of InP nanobeam cavities using atomic layer deposition

Photonic crystal nanobeam cavities are valued for their small mode volume, CMOS compatibility, and high coupling efficiency-crucial features for various low-power photonic applications and quantum information processing. However, despite their potential, nanobeam cavities often suffer from low quality factors due to fabrication imperfections that create surface states and optical absorption. In this work, we demonstrate InP nanobeam cavities with up to 140% higher quality factors by applying a coating of Al 2 O 3 via atomic layer deposition to terminate dangling bonds and reduce surface absorption. Additionally, changing the deposition thickness allows precise tuning of the cavity mode wavelength without compromising the quality factor. This Al 2 O 3 atomic layer deposition approach holds great promise for optimizing nanobeam cavities that are well-suited for integration with a wide range of photonic applications.

42 ENGINEERING↗

Medium Temperature Furnace Baking of Low-beta 650 MHz Five-cell Cavities

Medium Temperature baking of low beta 650 MHz cavities was conducted in a UHV furnace. A systematic study of cavity surface resistance components, residual and BCS, was conducted, including analyzing surface resistance due to trapped magnetic flux. Cavities showed an average 4.5 nano-ohm surface resistance at 17 MV/m under 2 K, which meets PIP-II specifications with a 40% margin. The results provided helpful information for the PIP-II project to optimize the cavity processing recipe for cryomodule application. The results were compared to the 1.3 GHz cavity that received a similar furnace baking.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Nb3Sn Coating of Twin Axis Cavity and Other Complex SRF Cavity Structures

In the field of Accelerator Science, for the low cost and increased quality factor, thin films coated niobium cavities are used in the modern SRF research. Within the potential substances, Nb3Sn has shown higher critical temperature than niobium. Here the tin vapor diffusion method is used as the preferred technique to coat niobium cavities. So far, only elliptical cavities have been coated with Nb3Sn and this technique has not yet been applied to cavities with complex geometries, which are also helpful in the accelerator science field. The Half-wave resonator could provide us data across frequencies of interest for particle accelerators world wide. Similarly the Twin axis cavity proposed for Energy Recovary Linac (ERL) applications could benefit from Nb3Sn coating. But with their advanced geometries, increased area, more number of ports and hard to reach areas, a different coating approach is needed to provide a uniform coating of Nb3Sn. We used twin axis cavity to optimize the coating technique and followed a low temperature annealing to further improvement of the thin film quality by low temperature annealing as a post coating method. With these we could expand the current coating system at JLab to coat complex cavity models

Tiskumara, Jayendrika↗

Novel, Middle and Long Wave Infrared Laser Sources For Accelerator Applications

The main accomplishment during Years 2020-2024 of the DOE Accelerator Stewardship Program is proof-of-principle demonstration of amplification of an ultrashort 10 µm seed pulse in a multiatmosphere CO 2 laser optically pumped by nanosecond pulses of either a ~4.3 µm Fe:ZnSe laser or a 2.8 µm electro-optically (EO) Q-switched Er: Laser. This has been accomplished at the UCLA Neptune Laboratory by using about 100 mJ, ~100 ns long pulses generated by the pump laser built for this purpose by the UAB team. Implementation of EO Q-switching regime in the solid-state Er:laser system made possible nanosecond synchronization between the pump pulse and the 0.5 ps seed pulse produced by a commercial Ti:sapphire laser based mid-IR OPA/DFG. The injection mode-locking regime realized in a compact Mult atmosphere 3 Hz CO 2 -He regenerative amplifier enabled generation of a train of ultrashort pulses separated by the cavity round-trip time of ~3.2 ns. The measured gain lifetime of ~1 µs at a total pressure of ~12-15 atm indicates that lifetime of the upper laser level is a critical limiting factor in designing high-pressure CO 2 amplifiers. A single picosecond 10 mm pulse with an energy 0.1-0.2 mJ was extracted from the amplifier’s cavity using an ultrafast Ge semiconductor switch whose reflectivity was photo-induced by a femtosecond 800 nm pulse. For direct amplification regime, nonlinear absorption in Ge at 10 mm at GW/cm 2 intensities limited the extracted energy. Therefore, the generated energy could be further increased by minimizing losses in the switch and optimizing the cavity mode size. Based on the obtained data in collaboration with BNL colleagues, we have designed a high-pressure CO 2 amplifier to be used as a preamplifier for the future experiments at the ATF BNL. The latter work is the subject of funding availability.

60 APPLIED LIFE SCIENCES↗

“A System for Automatically Maintaining Pressure in a Commercial Truck Tire”

Under-inflated tires significantly reduce a vehicle’s fuel efficiency by increasing rolling resistance (drag force). The Air Maintenance Technology (“AMT”) system developed through this project replenishes lost air and maintains optimal tire cavity pressure whenever the tire is rolling in service, thus improving overall fuel economy by reducing the tire’s rolling resistance. The system consists of an inlet air filter, an air pump driven by tire deformation during rotation, and a pressure regulating device. Pressurized air in the tire cavity naturally escapes by diffusion through the tire and wheel, leaks in tire seating, and through the filler valve and its seating. As a result, tires require constant maintenance to replenish lost air. Since manual tire inflation maintenance is both labor intensive and time consuming, it is frequently overlooked or ignored. By automating the maintenance of optimal tire pressure, the tire’s contribution to the vehicle’s overall fuel economy can be maximized. The work was divided into three phases. The objectives of Phase 1, Planning and Initial Design, resulted in an effective project plan and to create a baseline design. The objectives for Phase 2, Design and Process Optimization, were: to identify finalized design for the pump, regulator and filter components; identify a process to build prototype tires; assemble prototype tires; test prototype tires and document results. The objectives of Phase 3, Design Release and Industrialization, were to finalize system tire assembly, perform release testing and industrialize the assembly process.

42 ENGINEERING↗

Final Cooling with Thick Wedges for a Muon Collider

A muon collider is a particle accelerator that collides muons rather than protons or electrons. An important component of such a collider is cooling, in which the emittance of the muon beam is reduced to make it suitable for use in a collider. In the last stage of this process, called final 4D cooling, emittance in the transverse axes is reduced while emittance in the longitudinal axis is allowed to grow. In previous studies, Final 4-D cooling used absorbers within very high field solenoids to cool low-momentum muons. Simulations of the systems did not reach the desired cooling design goals. In this study, we develop and optimize a different conceptual design for the final 4D cooling channel, which is based on single thick wedges. We used G4Beamline to simulate the channel and Python to generate and analyze particle distributions. We characterized the effects of various parameters on the performance of this system, including the initial emittances and Twiss parameters, the length and angle of the wedges, the length of the drift channel, and the length, frequency, gradient, and phase of the RF cavities. We optimized the design parameters of the cooling channel and produced two conceptual designs (corresponding to two possible starting points for the input beam) which achieve transverse cooling in both x and y by a factor of ≈ 3.5. These channels achieve a lower transverse and longitudinal emittance than the best design previously published.

43 PARTICLE ACCELERATORS↗

Optimization of a hot-cavity type resonant ionization laser ion source

Resonant Ionization Laser Ion Source (RILIS) is nowadays an important technique in many Radioactive Ion Beam (RIB) facilities for its reliability and ability to ionize efficiently and element selectively. Grand Accélérateur National d’Ions Lourds (GANIL) Ion Source using Electron Laser Excitation (GISELE) is an off-line test bench for RILIS developed to study a fully operational resonant laser ion source at GANIL facility. The ion source body has been designed as a modular system to investigate different experimental approaches by varying the design parameters, to develop the future on-line laser ion source. The aim of this project is to determine the best technical solution which combines high selectivity and ionization efficiency with small ion beam emittance and stable long term operation. Latest results concerning emittance and time profile development as a function of the temperature for different ion source versions will be presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Room Temperature Lasing from Semiconducting Single-Walled Carbon Nanotubes

Miniaturized near-infrared semiconductor lasers that are able to generate coherent light with low energy consumption have widespread applications in fields such as optical interconnects, neuromorphic computing, and deep-tissue optogenetics. With optical transitions at near-infrared wavelengths, diameter-tunable electronic structures, and superlative optoelectronic properties, semiconducting single-walled carbon nanotubes (SWCNTs) are promising candidates for nanolaser applications. However, despite significant efforts in this direction and recent progress toward enhancing spontaneous emission from SWCNTs through Purcell effects, SWCNT-based excitonic lasers have not yet been demonstrated. Leveraging an optimized cavity-emitter integration scheme enabled by a self-assembly process, here we couple SWCNT emission to the whispering gallery modes supported by polymer microspheres, resulting in room temperature excitonic lasing with an average lasing threshold of 4.5 kW/cm 2 . The high photostability of SWCNTs allows stable lasing for prolonged duration with minimal degradation. Finally, this experimental realization of excitonic lasing from SWCNTs, combined with their versatile electronic and optical properties that can be further controlled by chemical modification, offers far-reaching opportunities for tunable near-infrared nanolasers that are applicable for optical signal processing, in vivo biosensing, and optoelectronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A phononic interface between a superconducting quantum processor and quantum networked spin memories

We introduce a method for high-fidelity quantum state transduction between a superconducting microwave qubit and the ground state spin system of a solid-state artificial atom, mediated via an acoustic bus connected by piezoelectric transducers. Applied to present-day experimental parameters for superconducting circuit qubits and diamond silicon-vacancy centers in an optimized phononic cavity, we estimate quantum state transduction with fidelity exceeding 99% at a MHz-scale bandwidth. By combining the complementary strengths of superconducting circuit quantum computing and artificial atoms, the hybrid architecture provides high-fidelity qubit gates with long-lived quantum memory, high-fidelity measurement, large qubit number, reconfigurable qubit connectivity, and high-fidelity state and gate teleportation through optical quantum networks.

47 OTHER INSTRUMENTATION↗