Results for “carbon defects” — Page 4

DOE OSTI2024

Effects of uranium metal carbon content on hydriding kinetics and corrosion blister number/area at sub-ambient pressures

Carbon is a common impurity in uranium metal, resulting in a number of uranium–carbon inclusion phases that contribute to an increase in metal defect density as carbon content increases. It is widely held that uranium hydride corrosion preferentially nucleates at these defect sites, and that an increase in carbon content will therefore represents an increase in uranium hydride corrosion sites on the metal surface. We hydrided six uranium sources with differing carbon contents to explore whether this assumption holds in a sub-ambient (~ 0.1 atm hydrogen), sealed environment, and report the resulting reaction kinetics and uranium hydride blister benchmarking data. We find that carbon content is not strongly correlated with reaction kinetics terms or the resulting hydride blister number and area, but that there is a tight relationship between corrosion blister number/area and kinetics as is expected. Further, we find that there is a strong trend of decreasing variance in the blister number, blister area, and induction time as carbon content increases (higher carbon content results in more reproducible blister populations). Additionally, we find a narrow band of uranium metal consumption at the end of the parabolic phase of reaction progress (beginning of linear growth phase) of 0.098 ± 0.011 w/w%, a fact that may be useful in assaying hydrogen corrosion of uranium metal within sealed environments generally.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2024

Carbon-Related Quantum Emitter in Hexagonal Boron Nitride with Homogeneous Energy and 3-Fold Polarization

Not Available

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2022

Mesoporous Carbon-Based PGM-Free Catalyst Cathodes

Polymer electrolyte membrane fuel cell (PEMFC) is the most promising energy conversion technology which can be used as the power sources for the electric vehicles with the ultimate cleanness, (no carbon emission from the use of hydrogen), much-improved energy conversion efficiency, longer range, and rapid refueling. However, due to the large amount of platinum group metal (PGM) catalyst used in PEMFC electrodes, the high cost is the bottleneck for the broad commercialization of PEMFCs for transportation. Hence, there is a critical need to develop low-cost, high-performance PGM-free cathode catalysts that can dramatically reduce the cost of the catalyst in the PEMFC by one to two orders of magnitude. However, before PGM-free cathodes become viable, several technical challenges associated with PGM-free cathodes must be addressed, including the insufficient activity and stability of the catalysts as well as the large transport losses from the much thicker catalyst layer in the electrodes.

08 HYDROGEN↗

NASA NTRSDate not supplied

TPSAS-NF1676L-27788-DND

NASA Advanced Composites Project (ACP) - Reduce timeline required for development and certification of advanced composite structures by 30 percent Manufacturing Defects - Detrimentally affect quality of parts - Lead to higher cost and cause significant delay Developed guided wave-based technique for detection of manufacturing defects in carbon fiber reinforced polymer (CFRP) composites Extended guided wave - based technique for in-situcure monitoring of composites using high temperature piezoelectric transducers Incorporated embedded fiber Bragg grating (FBG) sensors for guided wave sensing during cure.

Tyler B Hudson↗

DOE OSTI2025

Interpretation of Ion Irradiation and Neutron Irradiation Damage in Additively Manufactured 316 Stainless Steel using Multiscale Modeling

The accelerated adoption of nuclear energy necessitates advanced manufacturing technologies, such as additive manufacturing, to meet heightened supply chain requirements and support innovative reactor technologies. Due to the unique microstructural characteristics of additively manufactured materials under distinct solidification conditions, comprehensive evaluation of their performance in reactor environments is essential. The Advanced Materials and Manufacturing Technologies program under the Department of Energy's Office of Nuclear Energy focuses on understanding the irradiation performance and damage evolution of laser powder bed fusion 316 stainless steel, with an emphasis on integrating ion and neutron irradiation data to accelerate the development and qualification of materials for advanced nuclear reactor applications. While ion irradiation is a cost- and time-effective method, modeling and simulation are required to interpret the data for the broader range of irradiation conditions encountered in advanced reactors. In fiscal year 2025, integrated multiscale modeling and simulations were conducted to assess irradiation damage in additively manufactured 316 stainless steel. Key outcomes include predictions of chromium enrichment at grain boundaries, nickel enrichment at dislocation cell walls and void surfaces, and heterogeneous void evolution under ion and neutron irradiation conditions. Cluster dynamics simulations revealed the coarsening of voids at high irradiation temperatures and the suppression of void growth by high network dislocation density, while also demonstrating significant growth and coarsening of voids and self-interstitial atom loops at low dose rates. Machine learning-accelerated atomistic simulations highlighted the impact of the local environment and chromium concentration on vacancy diffusivity, providing key insights on the influence of composition on void swelling and radiation-induced segregation. Additionally, molecular dynamics simulations demonstrated the presence of defect production bias and a significant effect of carbon content on defect cluster behavior. These combined efforts aim to predict the performance of additively manufactured materials under various reactor conditions, supporting their qualification for nuclear reactor applications by interpreting ion irradiation data. This report underscores the potential of integrated multiscale modeling to analyze ion irradiation data in the effort to accelerate the qualification of additively manufactured materials for nuclear reactor components.

316 stainless steel↗

DOE OSTI2022

Defect formation and bending properties in graphite under He atom implantation investigated by molecular dynamics method

The formation and evolution of radiation defects and their effects on bending property of a single graphite under low energy helium atom implantation have been studied at atomic scale through molecular dynamics simulations. Various simple interstitial and vacancy defects are observed during the implantation process, which is a function of incident energy and cross section of helium-carbon interaction. Large defects are observed after continuous helium atom implantations. The effects of incident energy on the density, size and distribution of defects are analyzed in detail. Furthermore, the kinetic evolution process of radiation defects at different annealing temperatures have also been simulated, including the migration, aggregation, transformation, coalescence, and self-healing. Here, the large defect clusters, crossing several carbon layers, have been confirmed to be the primary reasons that affect the bending property of graphite. All these results provide a new understanding for further applications of graphite in nuclear reactors.

Atomic implantation↗

NASA NTRSDate not supplied

Computational Investigation of Oxidative Etch Pitting in FiberForm and Its Impact on Material Properties

Oxidation-driven carbon erosion does not occur uniformly but rather through the development of localized etch pits at active surface sites. These active sites form due to atomic defects on the carbon surface, making them significantly more reactive than the surrounding, non-defective areas. As a result, these sites are the first to react during ablation, leading to their removal. This process creates new defects in neighboring atoms, increasing their reactivity and causing localized carbon removal around these active sites. In this way, the highly reactive defective areas serve as nucleation points for the formation and growth of etch pits, which can have adverse effects on structural integrity of FiberForm. To better understand how these etch pits impact the material properties of carbon fiber microstructures, we have developed a new capability within the direct simulation Monte Carlo (DSMC) framework to capture the etch pit formation process. This capability, integrated into the DSMC code SPARTA (Stochastic Parallel Rarefied-gas Time-accurate Analyzer), models material removal in the presence of active sites, leading to the formation of etch pits. The current work focuses on studying the effects of these etch pits on the material properties of FiberForm, a widely used base material in thermal protection systems (TPS). The microstructure of virgin FiberForm, obtained via X-ray microtomography, is imported into SPARTA to generate the ablated geometries with etch pits. These modified microstructures are then analyzed using the Porous Microstructure Analysis (PuMA) software to compute various material properties, including elasticity, thermal conductivity, and permeability. We investigate the variation of these properties due to the complex surface topology changes caused by etch pit formation. Additionally, we compare the effects of pitting with the conventional model of shrinking fibers, traditionally used to simulate the ablation of carbon structures. Significant differences emerge between the two approaches. Consequently, this physically realistic model of material removal through etch pit formation offers improved accuracy in predicting the degradation of carbon-based TPS during oxidation. It also provides insights into other mechanisms, such as spallation, where chunks of material are removed into the flow due to etch pit growth. Ultimately, this model enhances our understanding of failure modes in these materials during ablation.

PuMA↗

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

DOE OSTI2024

Optical Properties of Low‐Defect Large‐Area Hexagonal Boron Nitride for Quantum Applications

Intrinsic defects and their concentrations in hexagonal boron nitride (h-BN) play a key role in single-photon emission. In this study, the optical properties of large-area multilayer h-BN-on-sapphire grown by metal-organic chemical vapor deposition are explored. Based on the detailed spectroscopic characterization using both cathodoluminescence (CL) and photoluminescence (PL) measurements, the material is devoid of random single-point defects instead of a few clustered complex defects. The emission spectra of the measurements confirm a record-low-defect concentration of ≈10 4 cm −2 . Post-annealing, no significant changes are observed in the measured spectra and the defect concentrations remain unaltered. Through CL and PL spectroscopy, an optically active boron vacancy spin defect is identified and a novel complex defect combination arising from carbon impurities is revealed. This complex defect, previously unreported, signifies a unique aspect of the material. In these findings, the understanding of defect-induced optical properties in h-BN films is contributed, providing insights for potential applications in quantum information science.

42 ENGINEERING↗

DOE OSTI2024

Enhancing the Carbon Monoxide Oxidation Performance through Surface Defect Enrichment of Ceria-Based Supports for Platinum Catalyst

Effective synthesis and application of single-atom catalysts on supports lacking enough defects remain a significant challenge in environmental catalysis. Herein, we present a universal defect-enrichment strategy to increase the surface defects of CeO 2 -based supports through H 2 reduction pretreatment. The Pt catalysts supported by defective CeO 2 -based supports, including CeO 2 , CeZrO x , and CeO 2 /Al 2 O 3 (CA), exhibit much higher Pt dispersion and CO oxidation activity upon reduction activation compared to their counterpart catalysts without defect enrichment. Specifically, Pt is present as embedded single atoms on the CA support with enriched surface defects (CA-HD) based on which the highly active catalyst showing embedded Pt clusters (Pt C ) with the bottom layer of Pt atoms substituting the Ce cations in the CeO 2 surface lattice can be obtained through reduction activation. Embedded PtC can better facilitate CO adsorption and promote O 2 activation at Pt C –CeO 2 interfaces, thereby contributing to the superior low-temperature CO oxidation activity of the Pt/CA-HD catalyst after activation.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Catalytic reduction of carbon dioxide to methanol over defect-laden hexagonal boron nitride: insights into reaction mechanisms

Abstract We present a density functional theory-based mechanistic understanding of CO 2 hydrogenation to value-added products on a nitrogen-vacancy (V N ) defect in hexagonal boron nitride ( dh -BN). Activation occurs through back-donation to the π * orbitals of CO 2 from the frontier orbitals (defect state) of the h- BN sheet that are localized near a nitrogen-vacancy. Subsequent hydrogenation to methanol (CH 3 OH) and formic acid (HCOOH) proceed through vacancy-facilitated co-adsorption of hydrogen and CO 2 . More importantly, our reaction pathway analyses complimented by microkinetic modeling indicate that dh -BN is potentially a low-temperature, selective catalyst for CO 2 reduction to methanol. Our findings are in agreement with experiments conducted in a mechanical reactor that show high selectivity towards methanol formation for CO 2 hydrogenation on defect induced h- BN.

Jiang, Tao (ORCID:0000000304197288)↗

NASA NTRSDate not supplied

Investigation of the effect of etch pits on the material properties of carbon fiber structures

It is well known that etch pits are formed on carbon surfaces during their consumption in reactive gas environments such as during ablation of carbon-based thermal protection system (TPS) materials. These pits start out from atomic defects on the carbon surface, grow in size and then ultimately lead to the complete removal of the solid carbon material [1, 2]. However, the effect of such etch pits on the material properties of carbon ablators such as FiberForm are poorly understood, as the maximum size of pits are on the order of microns in size, which makes them hard to observe experimentally. Hence, we have developed a module within the Porous Microstructure Analysis code PuMA [3] that can generate etch pits on an arbitrary material surface, with a prescribed distribution of pit size and density. Figure 1 shows a FiberForm sample with artificially generated pits of varying radii and pit density. We use this newly developed module to calculate material properties of FiberForm, which is the base material for one of the most commonly used TPS materials - Phenolic Impregnated Carbon Ablator (PICA). The detailed microstructure of FiberForm in PuMA will either be generated synthetically or obtained from X-ray microtomography [4]. Our simulations show that material properties such as the thermal conductivity and tortuosity decrease with increasing degree of pitting. This will be helpful to more accurately predict the degradation of carbon-based TPS during ablation, and furthermore may allow us to identify previously unknown TPS failure modes due to pitting.

PuMA↗

NASA NTRSDate not supplied

Investigation of the Effect of Etch Pits on the Material Properties of Carbon Fiber Structures

It is well known that etch pits are formed on carbon surfaces during their consumption in reactive gas environments such as during ablation of carbon-based thermal protection system (TPS) materials. These pits start out from atomic defects on the carbon surface, grow in size and then ultimately lead to the complete removal of the solid carbon material. However, the effect of such etch pits on the material properties of carbon ablators such as FiberForm are poorly understood, as the maximum size of pits are on the order of microns in size, which makes them hard to observe experimentally. Hence, we have developed a module within the Porous Microstructure Analysis code PuMA that can generate etch pits on an arbitrary material surface, with a prescribed distribution of pit size and density. We use this newly developed module to calculate material properties of FiberForm, which is the base material for one of the most commonly used TPS materials - Phenolic Impregnated Carbon Ablator (PICA). The detailed microstructure of FiberForm in PuMA will either be generated synthetically or obtained from X-ray microtomography. Our simulations show that material properties such as the thermal conductivity and tortuosity decrease with increasing degree of pitting. This will be helpful to more accurately predict the degradation of carbon-based TPS during ablation, and furthermore may allow us to identify previously unknown TPS failure modes due to pitting.

PuMA↗

DOE OSTI2024

Effect of Carbon on Void Nucleation in Iron

The study reports the significance of carbon presence in affecting void nucleation in Fe. Without carbon, void nucleation rates decrease gradually at high temperatures but remain significantly high and almost saturated at low temperatures. With carbon present, even at 1 atomic parts per million, void nucleation rates show a low-temperature cutoff. With higher carbon levels, the nucleation temperature window becomes narrower, the maximum nucleation rate becomes lower, and the temperature of maximum void nucleation shifts to a higher temperature. Fundamentally, this is caused by the change in effective vacancy diffusivity due to the formation of carbon-vacancy complexes. The high sensitivity of void nucleation to carbon comes from the high sensitivity of void nucleation to the vacancy arrival rate in a void. The void nucleation is calculated by first obtaining the effective vacancy diffusivity considering the carbon effect, then calculating the defect concentration and defect flux change considering both carbon effects and pre-existing dislocations, and finally calculating the void nucleation rate based on the recently corrected homogeneous void nucleation theory. The study is important not only in the fundamental understanding of impurity effects in ion/neutron irradiation but also in alloy engineering for judiciously introducing impurities to increase swelling resistance, as well as in the development of simulation and modeling methodologies applicable to other metals.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Nature of Oxygen Adsorption on Defective Carbonaceous Materials

Here, plane-wave density functional theory has been used to study oxygen adsorption on graphene, graphite, and (12,0) zigzag single-walled carbon nanotubes with and without Stone–Wales (SW) and single-vacancy (SV) defects to understand the role of defects on carbonaceous material reactivity. Atomic oxygen adsorption leads to the formation of an epoxide on defect-free graphene and graphite and an ether on the exterior wall of carbon nanotubes and SW-defected materials. O 2 chemisorption is endothermic on defect-free graphene and graphite and slightly exothermic on defect-free nanotubes. O 2 chemisorption energies are predicted to be –1.1 to –1.4 eV on an SW defect and –6.0 to –8.0 eV on an SV defect. An SW defect lowers the energy barriers by 0.90 and 0.50 eV for O 2 chemisorption on graphene and nanotubes, respectively. The formation of a C–O–O–C group is important for O 2 dissociation on defect-free and SW-defected materials. The energy barrier is less than 0.30 eV on an SV defect. The more reactive SW defect toward O adsorption on graphene is mostly due to the strained defective carbon atoms being able to donate more electrons to an O to form an ether. The larger 2s character in the hybrid orbitals in an ether than in an epoxide makes the ether C–O bond stronger. Stronger C–O binding on an SW-defective carbon nanotube than on a defect-free nanotube is in part due to more flexibility of the defect to release the epoxide ring strain to form an ether.

25 ENERGY STORAGE↗