Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “capillary flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Terrestrial Testing of the CapiBRIC, a Microgravity Optimized Brine Processor

Utilizing geometry based static phase separation exhibited in the radial vaned capillary drying tray, a system was conceived to recover water from brine. This technology has been named the Capillary BRIC; abbreviated CapiBRIC. The CapiBRIC utilizes a capillary drying tray within a drying chamber. Water is recovered from clean water vapor evaporating from the free surface leaving waste brine solids behind. A novel approach of optimizing the containment geometry to support passive capillary flow and static phase separation provides the opportunity for a low power system that is not as susceptible to fouling as membranes or other technologies employing physical barriers across the free brine surface to achieve phase separation in microgravity. Having been optimized for operation in microgravity, full-scale testing of the CapiBRIC as designed cannot be performed on the ground as the force of gravity would dominate over the capillary forces. However, subscale units relevant to full-scale design were used to characterize fill rates, containment stability, and interaction with a variable volume reservoir in the PSU Dryden Drop Tower (DDT) facility. PSU also using tested units scaled such that capillary forces dominated in a 1-g environment to characterize evaporation from a free-surface in 1-g upward, sideways and downward orientations. In order to augment the subscale testing performed by PSU, a full scale 1-g analogue of the CapiBRIC drying unit was initiated to help validate performance predictions regarding expected water recovery ratio, estimated processing time, and interface definitions for inlets, outlets, and internal processes, including vent gas composition. This paper describes the design, development and test of the terrestrial CapiBRIC prototypes.

Sargusingh, Miriam J.↗
DOE OSTI2022

Measurement of Resistance, Porosity, and Water Contact Angle of Porous Transport Layers for Low-Temperature Electrolysis Technologies

The porous transport layer is an important component of low-temperature electrolysis devices, such as proton exchange membrane water electrolyzers or anion exchange membrane water electrolyzers. PTLs have significant influence on the cell performance as their bulk resistance can impact the ohmic resistance, their contact resistance can impact electrode performance, and their structure can impact the liquid flow to the cell, which could cause mass-transport losses. In order to improve cell performance, optimization of the PTL is critical. Standardized protocols should be utilized to adequately compare PTLs being developed from different institutions. This method will detail a standardized protocol for measuring the resistance of the PTL using a four-wire setup and will also detail a process for measuring the porosity and water contact angle of the PTL using capillary flow porometry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Blood Plasma Self-Separation Technologies during the Self-Driven Flow in Microfluidic Platforms

Blood plasma is the most commonly used biofluid in disease diagnostic and biomedical analysis due to it contains various biomarkers. The majority of the blood plasma separation is still handled with centrifugation, which is off-chip and time-consuming. Therefore, in the Lab-on-a-chip (LOC) field, an effective microfluidic blood plasma separation platform attracts researchers’ attention globally. Blood plasma self-separation technologies are usually divided into two categories: active self-separation and passive self-separation. Passive self-separation technologies, in contrast with active self-separation, only rely on microchannel geometry, microfluidic phenomena and hydrodynamic forces. Passive self-separation devices are driven by the capillary flow, which is generated due to the characteristics of the surface of the channel and its interaction with the fluid. Comparing to the active plasma separation techniques, passive plasma separation methods are more considered in the microfluidic platform, owing to their ease of fabrication, portable, user-friendly features. We propose an extensive review of mechanisms of passive self-separation technologies and enumerate some experimental details and devices to exploit these effects. The performances, limitations and challenges of these technologies and devices are also compared and discussed.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Dean vortex-enhanced blood plasma separation in self-driven spiral microchannel flow with cross-flow microfilters

Point-of-care (POC) diagnostic devices have been developing rapidly in recent years, but they are mainly using saliva instead of blood as a test sample. A highly efficient self-separation during the self-driven flow without power systems is desired for expanding the point-of-care diagnostic devices. Microfiltration stands out as a promising technique for blood plasma separation but faces limitations due to blood cell clogging, resulting in reduced separation speed and efficiency. These limitations are mainly caused by the high viscosity and hematocrit in the blood flow. A small increment in the hematocrit of the blood significantly increases the pressure needed for the blood plasma separation in the micro-filters and decreases the separation speed and efficiency. Addressing this challenge, this study explores the feasibility of diluting whole blood within a microfluidic device without external power systems. This study implemented a spiral microchannel utilizing the inertial focusing and Dean vortex effects to focus the red blood cells and extract the blood with lower hematocrit. The inertial migration of the particles during the capillary flow was first investigated experimentally; a maximum of 88% of the particles migrated to the bottom and top equilibrium positions in the optimized 350 × 60 μm (cross-sectional area, 5.8 aspect ratio) microchannel. With the optimized dimension of the microchannel, the whole blood samples within the physiological hematocrit range were tested in the experiments, and more than 10% of the hematocrit reduction was compared between the outer branch outlet and inner branch outlet in the 350 × 60 μm microchannel.

Biochemistry & Molecular Biology↗
NASA NTRS2000

A Study of the Constrained Vapor Bubble Thermosyphon

The objective of this effort is to better understand the physics of evaporation, condensation, and fluid flow as they affect the heat transfer processes in a constrained vapor bubble heat exchanger (CVBHX). This CVBHX consists of a small enclosed container with a square cross section (inside dimensions. 3 x 3 x 40 mm) partially filled with a liquid. The major portion of the liquid is in the corners, which act as arteries. When a temperature difference is applied to the ends of the CVBHX, evaporation occurs at the hot end and condensation at the cold end resulting in a very effective heat transfer device with great potential in space applications. Liquid is returned by capillary flow in the corners. A complete description of the system and the results obtained to date are given in the papers listed.

Wayner, Peter C., Jr.↗
DOE OSTI2024

Characterization of Porous Transport Layers Towards the Development of Efficient Proton Exchange Membrane Water Electrolysis

The current goals for implementing the hydrogen economy have highlighted a need to further optimize water-splitting technologies for clean hydrogen production. Proton exchange membrane water electrolysis (PEMWE) is a leading technology, but further optimizations of anode materials including the porous transport layer (PTL) and the adjacent catalyst layer (CL) are required to increase overall cell performance and reduce cost. This literature review describes advances in PTL development and characterization, highlighting early PTL characterization work and most common methods including capillary flow porometry and mercury intrusion porometry, optical imaging, neutron and x-ray radiography, and x-ray computed tomography. The article also discusses PTL protective coatings and their characterizations, focusing on platinum group metal (PGM)-based coatings, alternative non-PGM-based coatings, post-treated PTLs, and investigations into thin PGM-based coatings. Furthermore, it highlights the integration of the PTL and the adjacent CL along with associated characterization challenges. Lastly, this review discusses future developments in the characterization needed to improve PEMWE's performance and long-term durability are discussed.

08 HYDROGEN↗
DOE OSTI2025

Process intensification approach to enhancing heat and mass transfer during drying: Ultrasonic (US) assisted drying of paper and board

Drying of paper and board is conventionally achieved through alternating conduction (steam-heated cylinders) and pocket convection (heated air over the paper web surface). These conventional drying systems rely heavily on steam from fossil fuels, resulting in inefficiencies, high energy usage, and thermal losses due to surface-driven mechanisms. Here, to address these challenges, an experimental system, with in-situ drying characteristics measurements, was developed to investigate process intensification using ultrasonic-based dewatering—a volumetric, pressure-driven acoustic energy system—integrated with conventional drying. The objectives of this study are to assess the impact of ultrasonics (US) on dewatering; compare performances to conventional drying systems; identify improvements in drying rate and energy use as a function of moisture content; and gain potential insights on heat and mass transfer mechanisms during US-assisted drying. US performance was evaluated across frequencies, power levels, pulp types, and basis weights. Results show that improvements to ultrasonic applications in conjunction with convection were 30-43% in drying rate and 20-35% in drying time over continuous and intermittent applications. When combined with conduction and convection, ultrasonics yielded up to 20% improvement in both rate and time and up to 20% reduction in energy consumption. Observations support a hypothesis of extension of the constant rate period due to improved capillary flow at higher moisture content and enhancing vapor diffusion and boundary layer disruption at lower moisture contents during falling rate period. These findings will inform future modeling, simulation, design and optimization of advanced drying systems.

42 ENGINEERING↗
DOE OSTI2023

Species, Pathways, and Timescales for NH 3 Formation by Low-Temperature Atmospheric Pressure Plasma Catalysis

Species, pathways, and timescales for NH3 production by plasma catalysis over transition-metal wools are determined by measuring plasma-derived species densities [N, H, and N 2 (v)], quantitatively correlating consumption of these species with NH 3 formation, and measuring consumption of plasma-derived species at different residence times. These findings are enabled by a capillary flow through Ar/N 2 /H 2 plasma jet reactor setup that allows for the measurement of gas-phase species densities by molecular beam mass spectrometry. Surface-mediated reactions involving N radicals are responsible for NH 3 formation over Fe, Ni, and Ag surfaces. N reacts to form NH 3 with ~100% selectivity over Ni and Ag when H/N > 3 and % H 2 ≥ 0.5. The selectivity to ammonia drops as H and H 2 densities decrease for each catalyst. A comparison between amounts of NH 3 formed and N consumed with and without catalysts present shows that surface reactions enable higher and more selective conversion of N to NH 3 than gas-phase reactions alone. The conversion of N to NH 3 is negligible in the absence of H, demonstrating that H is required to produce NH 3 at these operating conditions. The consumption of N occurs on the same timescale as NH 3 formation, further confirming that reactions involving N contribute to NH 3 formation. Though vibrationally excited N 2 [N 2 (v)] is produced in quantities exceeding N by 100-fold, consumption of N 2 (v) on the catalytic surface does not contribute to NH 3 formation. Furthermore, these findings show that for low-temperature atmospheric pressure plasma catalysis, surface- mediated reactions among radical N and H species drive NH 3 formation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

An automated liquid jet for fluorescence dosimetry and microsecond radiolytic labeling of proteins

X-ray radiolytic labeling uses broadband X-rays for in situ hydroxyl radical labeling to map protein interactions and conformation. High flux density beams are essential to overcome radical scavengers. However, conventional sample delivery environments, such as capillary flow, limit the use of a fully unattenuated focused broadband beam. An alternative is to use a liquid jet, and we have previously demonstrated that use of this form of sample delivery can increase labeling by tenfold at an unfocused X-ray source. Here we report the first use of a liquid jet for automated inline quantitative fluorescence dosage characterization and sample exposure at a high flux density microfocused synchrotron beamline. Our approach enables exposure times in single-digit microseconds while retaining a high level of side-chain labeling. This development significantly boosts the method’s overall effectiveness and efficiency, generates high-quality data, and opens up the arena for high throughput and ultrafast time-resolved in situ hydroxyl radical labeling.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Mass Transport in Binary TiO 2 :SiO 2 and GeO 2 :SiO 2 Direct Ink Write Glasses

The mass transport mechanisms of Ti in TiO 2 :SiO 2 and Ge in GeO 2 :SiO 2 direct ink write, additively manufactured glasses were studied. Due to the low solubility of Ti in SiO2 and high melting point of TiO 2 relative to SiO 2 , Ti transport was found to occur via solid state interdiffusion between adjoining SiO 2 and TiO 2 precursor particles. The diffusivity of titanium in SiO 2 measured over typical sintering temperatures (1000-1300 °C) using Rutherford backscattering spectrometry was D = 9.1 × 10 -7 [m2/sec] exp ($\frac{378[\frac{kJ}{mol}]}{RT}$. This provides an estimate of ~30 nm for the diffusion length under typical sintering conditions (2 hrs. at 1200 °C). Although Ti and Ge have similar diffusivities in SiO 2 glass at low concentrations, GeO 2 was found to be much more mobile during the sintering of printed GeO 2 :SiO 2 green bodies. This was evident in glasses with phase separated GeO 2 regions over length scales of ~10 μm and in experiments involving binary xerogels in which GeO 2 migrated over ~10 μm through cracked, porous SiO 2 layers. Large phase separated regions and long transport lengths in GeO 2 :SiO 2 suggest that the transport of GeO 2 occurs prior to the densification of the SiO 2 matrix via an alternative mechanism such as capillary flow. These results inform important considerations in the design of index modifying inks for the direct ink write process, namely initial precursor phase, mutual solubility with the base SiO 2 glass, and mass transport throughout the sintering process.

36 MATERIALS SCIENCE↗
NASA NTRS1966

Induction brazing

Induction brazed joint process using capillary flow of gold braze alloy in two directions

JOINT↗
NASA NTRS1973

Development of the weld-braze joining process

A joining process, designated weld-brazing, was developed which combines resistance spot welding and brazing. Resistance spot welding is used to position and aline the parts, as well as to establish a suitable faying-surface gap for brazing. Fabrication is then completed at elevated temperature by capillary flow of the braze alloy into the joint. The process was used successfully to fabricate Ti-6Al-4V alloy joints by using 3003 aluminum braze alloy and should be applicable to other metal-braze systems. Test results obtained on single-overlap and hat-stiffened panel specimens show that weld-brazed joints were superior in tensile shear, stress rupture, fatigue, and buckling compared with joints fabricated by conventional means. Another attractive feature of the process is that the brazed joint is hermetically sealed by the braze material, which may eliminate many of the sealing problems encountered with riveted or spot welded structures. The relative ease of fabrication associated with the weld-brazing process may make it cost effective over conventional joining techniques.

Bales, T. T.↗
NASA NTRS1972

Weld-brazing - a new joining process

A joining process designated weld brazing which combines resistance spot welding and brazing has been developed. Resistance spot welding is used to position and align the parts as well as to establish a suitable faying surface gap for brazing. Fabrication is then completed by capillary flow of the braze alloy into the joint. The process has been used successfully to fabricate Ti-6Al-4V titanium alloy joints using 3003 aluminum braze alloy. Test results obtained on single overlap and hat-stiffened structural specimens show that weld brazed joints are superior in tensile shear, stress rupture, fatigue, and buckling than joint fabricated by spotwelding or brazing. Another attractive feature of the process is that the brazed joints is hermetically sealed by the braze material.

Bales, T. T.↗
NASA NTRS1973

Flight/ground sample comparison relating to flight experiment M552, exothermic brazing

Comparisons were made between Skylab and ground-based specimens of nickel and stainless steel which were vacuum brazed using silver-copper-lithium alloy with various joint configurations. It was established that the absence of gravity greatly extends the scope of brazing since capillary flow can proceed without gravity interference. There was also evidence of enhanced transport, primarily in that liquid silver copper alloy dissolves nickel to a much greater extent in the zero gravity environment.

Heine, R. W.↗
NASA NTRS1974

Metallurgical processing in space

Research in metallurgical processing to study the effects of reduced gravity started with Apollo 14 and advanced with Skylab. Experiments provided specimens for analysis which solidified while constrained and while freely floating, which contained a mixture of normally immiscible materials, demonstrated enhanced capillary flow, solubility and ordered growth of a directionally solidified eutectic. The smaller, equiaxed grain structure obtained in reduced gravity compared to the larger, elongated grains obtained in one gravity indicate a difference in convection due to gravity in constrained solidification. Freely floating nickel alloy specimens showing metallic gas evolution at low pressure and reduced gravity suggest reduced pressure reactions which cannot occur on earth even in high vacuum chambers due to the hydrostatic head in the molten metal. Directionally solidified eutectics showed fewer termination defects when grown in reduced gravity. These are a few of the differences observed due to reduced gravity which could have important consequences on the future of metallurgy. In this paper we attempt to correlate the results of several Skylab solidification experiments.

Mckannan, E. C.↗
NASA NTRS1976

Metal melting, joining, and alloying under weightlessness

During the Skylab mission experiments were conducted concerning the influence of weightlessness on molten metals and the solidification process. It was found that the absence of gravity-induced thermal convection and sedimentation modified the properties of the bulk melt. A metals melting experiment was conducted to study the behavior of metal melted by an electron beam and to evaluate the feasibility of joining metals in space. An exothermic brazing experiment investigated the spreading, mixing, and capillary flow of molten braze material. The containerless melting and solidification of small samples of several metals was studied in another experiment. A description is also given of a study of the directional solidification of solid solution alloys.

Snyder, R. S.↗
NASA NTRS1979

Dynamic regulation of erythropoiesis: A computer model of general applicability

A mathematical model for the control of erythropoiesis was developed based on the balance between oxygen supply and demand at a renal oxygen detector which controls erythropoietin release and red cell production. Feedback regulation of tissue oxygen tension is accomplished by adjustments of hemoglobin levels resulting from the output of a renal-bone marrow controller. Special consideration was given to the determinants of tissue oxygenation including evaluation of the influence of blood flow, capillary diffusivity, oxygen uptake and oxygen-hemoglobin affinity. A theoretical analysis of the overall control system is presented. Computer simulations of altitude hypoxia, red cell infusion hyperoxia, and homolytic anemia demonstrate validity of the model for general human application in health and disease.

Leonard, J. I.↗
NASA NTRS1982

Proceedings of the Second International Colloquium on Drops and Bubbles

Applications of bubble and drop technologies are discussed and include: low gravity manufacturing, containerless melts, microballoon fabrication, ink printers, laser fusion targets, generation of organic glass and metal shells, and space processing. The fluid dynamics of bubbles and drops were examined. Thermomigration, capillary flow, and interfacial tension are discussed. Techniques for drop control are presented and include drop size control and drop shape control.

Lecroissette, D. H.↗