Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “burn model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Real-Time Control of Lean Blowout in a Turbine Engine for Minimizing No(x) Emissions

This report describes research on the development and demonstration of a controlled combustor operates with minimal NO, emissions, thus meeting one of NASA s UEET program goals. NO(x) emissions have been successfully minimized by operating a premixed, lean burning combustor (modeling a lean prevaporized, premixed LPP combustor) safely near its lean blowout (LBO) limit over a range of operating conditions. This was accomplished by integrating the combustor with an LBO precursor sensor and closed-loop, rule-based control system that allowed the combustor to operate far closer to the point of LBO than an uncontrolled combustor would be allowed to in a current engine. Since leaner operation generally leads to lower NO, emissions, engine NO, was reduced without loss of safety.

Zinn, Ben↗
NASA NTRS2019

Space Launch System and Missions to Near Rectilinear Halo Orbits

The first major evolution of NASA’s Space Launch System (SLS) will begin its flights starting in the mid-2020’s. This new configuration, called Block 1B, replaces the Interim Cryogenic Propulsion Stage with a larger Exploration Upper Stage (EUS). The additional capability provided by the new upper stage will allow SLS to send heavier payloads into deep space. One destination of interest to the SLS program is called a Near Rectilinear Halo Orbit (NRHO). This is a type of lunar orbit with multiple advantages for deep space exploration. These benefits include Earth/lunar access, low station-keeping requirements, and high communication potential with Earth. Therefore, it is a leading candidate for the proposed Lunar Orbital Platform-Gateway (LOP-G). This paper will provide a detailed assessment of the SLS Block 1B requirements and capabilities for sending payloads to an NRHO. Analysts at Marshall Space Flight Center are producing a multi-year mission availability scan for the SLS Block 1B configuration to a predefined NRHO orbit. The analysis produces an optimized trajectory for each day of the scan window. A maximized payload and minimized propellant requirement are determined for each day. All maneuvers from launch to the end of the Trans-Lunar-Injection (TLI) are being modeled as finite burns. Injections into an NRHO are being modeled as impulsive maneuvers. The payload element is arbitrary, but includes sufficient mass to represent a large habitat or propulsion module. The resulting parameters of payload capability, delta-v requirements, and launch windows length vary over the course of the scan. Many launch days in the scan are eliminated in post-processing as they violate mission constraints such as payload mass and propellant usage to insert into an NRHO. Based off previous one-year scan results for the SLS Block 1B Design Analysis Cycle 2 (DAC-2), it is expected that there will be one to three days per week where the payload is able to insert into an NRHO within SLS constraints objectives. This scan provides results for longer than one-year, allowing analysts to better understand the launch availability and energy requirements of SLS Block 1B over time. The in-space mission design and scans utilize Copernicus, an n-body trajectory optimization tool originally developed out of the University of Texas at Austin with further development at Johnson Space Center in Houston, TX. To seed the in-space trajectory, Copernicus uses a plugin to call a database of SLS ascent trajectories optimized in the Program to Simulate Optimized Trajectories II (POST2). The ascent trajectories are developed using a framework that parametrizes payload mass and LEO inclination, and targets a 100 nmi (nautical mile) altitude circular parking orbit. Though this analysis is specific to the SLS program, it will provide a summary of mission design benefits and constraints associated with generic NRHO access, and may be applied to other programs or concepts that will utilize this orbit.

Statham, T. L.↗
NASA NTRS1991

Numerical study of external burning flowfields

This paper demonstrates the successful application of CFD to modeling an external burning flowfield. The study used the 2D, 3D, and PNS versions of the SPARK code. Various grids, boundary conditions, and ignition methodologies have been employed. Flameholding was achieved through the use of a subsonic outflow condition and a hot block located behind the step to ignite the fuel. Since the resulting burning produces a large subsonic region downstream of the cowl, this entire surface can be pressurized to the level of the back pressure. An evaluation of interactions between the ramjet exhaust and the external burning products demonstrate the complexity of this design issue. Ths code is now capable of evaluating the external burning effectiveness for flight vehicles using simple injector schemes, and the methodology can be readily applied to other external burning designs.

Bittner, Robert D.↗
NASA NTRS2006

Modeling the Optical Properties of Biomass Burning Aerosols: Young Smoke Aerosols From Savanna Fires and Comparisons to Observations from SAFARI 2000

Annually, farmers in southern Africa manage their land resources and prepare their fields for cultivation by burning crop residual debris, with a peak in the burning season occurring during August and September. The emissions from these fires in southern Africa are among the greatest from fires worldwide, and the gases and aerosol particles produced adversely affect air quality large distances from their source regions, and can even be tracked in satellite imagery as they cross the Atlantic and Pacific Ocean basins. During August and September 2000 an international group of researchers participating in the Southern African Regional Science Initiate field experiment (SAFARI 2000) made extensive ground-based, airborne, and satellite measurements of these gases and aerosols in order to quantify their amounts and effects on Earth's atmosphere. In this study we interpreted the measurements of smoke aerosol particles made during SAFARI 2000 in order to better represent these particles in a numerical model simulating their transport and fate. Typically, smoke aerosols emitted from fires are concentrated by mass in particles about 0.3 micrometers in diameter (1,000,000 micrometers = 1 meter, about 3 feet); for comparison, the thickness of a human hair is about 50 micrometers, almost 200 times as great. Because of the size of these particles, at the surface they can be easily inhaled into the lungs, and in high concentrations have deleterious health effects on humans. Additionally, these particles reflect and absorb sunlight, impacting both visibility and the balance of sunlight reaching -Earth's surface, and ultimately play a role in modulating Earth's climate. Because of these important effects, it is important that numerical models used to estimate Earth's climate response to changes in atmospheric composition accurately represent the quantity and evolution of smoke particles. In our model, called the Community Aerosol and Radiation Model for Atmospheres (CARMA) we used estimates of smoke emissions based on field studies and observations made with the NASA Terra and TRMM satellites. The meteorology used to calculate the transport was based on an assimilation of observed meteorological conditions provided by the National Center for Atmospheric Research.

Matichuk, R. I.↗
NASA NTRS1980

A numerical study of the NOL large-scale test

The large-scale gap test was modeled numerically using the reactive hydrodynamics code 2DE with forest fire burn rates. The model gives good agreement between calculated and experimental critical gap values. The calibration of peak pressure in the gap versus gap length is obtained from these calculations, and is in good agreement with the published experiment curve. The two dimensional nature of the gap test is evident from the curvature of the shock wave in the gap and test sample, and from the observed distance of run to detonation in the test samples.

Bowan, A. L.↗
NASA NTRS1980

Sympathetic reaction tests and analyses

The critical separation distances for explosive reactions of a solid rocket propellant were measured. Explosive reactions included low order explosion, low order detonation, and high order detonation. The effects of sample size, shape, damage and temperature on sympathetic reaction were determined experimentally. The sympathetic detonation of small cubes of solid rocket propellant was modelled numerically, using the Eulerian reactive hydrodynamic code 2DE with Forest Fire burn rates. The model was applied to cubes of 2.54 - 7.62 cm (1 - 3 in.), with agreement between calculated and experimental results.

Ricardson, D. E.↗
NASA NTRS1986

Effects of test facility contaminants on supersonic hydrogen-air diffusion flames

Results are presented from an analytical assessment of the effects of NO and H2O in air on the ignition and reaction of hydrogen. Three flow models of the burning process were used, each including a 32 reaction chemistry mechanism. These models were a plug flow reactor to determine ignition and reaction times; a well-stirred reactor to assess flame stability or blow-off; and a parabolic Navier-Stokes code to examine the diffusion flame combustion. The diffusion flame was computed for a cold supersonic H2 jet coaxial with a supersonic air stream at a static temperature of 1100 K and a pressure of 1 atmosphere.

Rogers, R. Clayton↗
NASA NTRS1986

Effects of test facility contaminants on supersonic hydrogen-air diffusion flames

Results are presented from an analytical assessment of the effects of NO and H2O in air on the ignition and reaction of hydrogen. Three flow models of the burning process were used, each including a 32 reaction chemistry mechanism. These models were a plug flow reactor to determine ignition and reaction times; a well-stirred reactor to assess flame stability or blow-off, and a parabolic Navier Stokes code to examine the diffusion flame combustion. The diffusion flame was computed for a cold supersonic H2 jet coaxial with a supersonic air stream at a static temperature of 1100 K and a pressure of 1 atmosphere.

Rogers, R. Clayton↗
NASA NTRS1994

A trajectory modeling investigation of the biomass burning-tropical ozone relationship

The hypothesis that tropical total O3 maxima seen by the TOMS satellite derive from African biomass burning has been tested using isentropic trajectory analyses with global meteorological data fields. Two case studies from the 1989 biomass burning season demonstrate that a large fraction of the air arriving at the location of TOMS O3 maxima passed over regions of intense burning. Other trajectories initiated at a series of points over Africa and the Atlantic suggest flight strategies for field studies to be conducted in September 1992.

Pickering, Kenneth E.↗
NASA NTRS2024

Improved Simulations of Biomass Burning Aerosol Optical Properties and Lifetimes in the NASA GEOS Model during the ORACLES-I Campaign

In order to improve aerosol representation in the NASA Goddard Earth Observing System (GEOS) model, we evaluated simulations of the aerosol properties and transport over the southern African biomass burning source and outflow region using observations made during the first deployment of the ORACLES (ObseRvations of Aerosols above CLouds and their intEractionS) field campaign in September 2016. An example case study of September 24 was analyzed in detail, during which aircraft-based in-situ and remote sensing observations showed the presence of a multi-layered smoke plume structure with significant vertical variation in single scattering albedo (SSA). Our baseline GEOS simulations were not able to represent the observed SSA variation, nor the observed organic aerosol-to-black carbon ratio (OA : BC). Analyzing the simulated smoke age suggests that the higher altitude, less absorbing smoke plume was younger (~4 days), while the lower altitude and more absorbing smoke plume was older (~7 days). We hypothesize a chemical or microphysical loss process exists to explain the change in aerosol absorption as the smoke plume ages, and we apply a simple 6-day e-folding loss rate to the model hydrophilic biomass burning OA to mimic this process. Adding this loss process required some adjustment to the model assumed scaling factors of aerosol emissions to conserve the regional aerosol loading and further improve the simulated OA : BC ratio. Accordingly, we have increased our biomass burning emissions of OA by 60 % and biomass burning BC by 15 %. We also utilized the ORACLES airborne observations to better constrain the simulation of aerosol optical properties, adjusting the assumed particle size, hygroscopic growth, and absorption. Our final GEOS model simulation with additional OA loss and updated optics showed a better performance in simulating AOD and SSA compared to independent ground and space-based retrievals for the entire month of September 2016, including the OMI Aerosol Index. In terms of radiative implications of our model adjustments, the final GEOS simulation suggested a decreased atmospheric warming of about 10 % (~2 W m -2 ) over the south-east Atlantic region and above the stratocumulus cloud decks compared to the model baseline simulations. These results improve the representation of the smoke age, transport, and optical properties in Earth system models.

aerosols↗
NASA NTRS1993

Erosive burning of solid propellants

Presented here is a review of the experimental and modeling work concerning erosive burning of solid propellants (augmentation of burning rate by flow of product gases across a burning surface). A brief introduction describes the motor design problems caused by this phenomenon, particularly for low port/throat area ratio motors and nozzleless motors. Various experimental techniques for measuring crossflow sensitivity of solid propellant burning rates are described, with the conclusion that accurate simulation of the flow, including upstream flow development, in actual motors is important since the degree of erosive burning depends not only on local mean crossflow velocity and propellant nature, but also upon this upstream development. In the modeling area, a brief review of simplified models and correlating equations is presented, followed by a description of more complex numerical analysis models. Both composite and double-base propellant models are reviewed. A second generation composite model is shown to give good agreement with data obtained in a series of tests in which composite propellant composition and heterogeneity (particle size distribution) were systematically varied. Finally, the use of numerical models for the development of erosive burning correlations is described, and a brief discussion of scaling is presented.

King, Merrill K.↗
NASA NTRSDate not supplied

LS-DYNA User-Defined Internal Ballistic Modeling

One of the challenges in modeling deflagration of solid propellants with LS-DYNA is its limited capability, which is mostly applicable to airbag systems that use gaseous nitrogen generated by burning sodium azide. To overcome this limitation and enable the modeling of custom propellant grains with specific geometries, perforations, surface inhibitors, impetus, burn rates, and co-volumes, a user-defined burn model must be defined. In this study, a custom internal ballistic analysis code is integrated into LS-DYNA to simulate kinematic systems driven by pyro-mechanical devices such as pyro pushers, cutters, thrusters, separations bolts, ejection seat catapults, etc. Step-by-step guidance is provided on implementing a user-defined loading subroutine and the requirements for compiling a custom LS-DYNA executable along with a simple pyro thruster example.

pyrotechnics↗
NASA NTRS1984

The direct effects of strain on burning rates of composite solid propellants

A mathematical model is developed to predict burn rate augmentation due to strain in a composite solid propellant. The model assumes the effect is due to the ability of the flame to penetrate the small fissures and voids that form when a propellant is strained. The number and size of these fissures is obtained by applying a flaw propagation analysis to randomly distributed flaws that form when the binder-oxidizer particle bonds break under stress. A flame height is calculated with Summerfield's burn rate equation and is used to compute the burn rate augmentation based upon the additional burn area created when the flame penetrates the fissures. Comparisons are made with data obtained from published sources. The existence of threshold pressure and strains, above which augmentation occurs, is verified although the model predicts a lower threshold pressure and higher threshold strain than expected. Further results and applications of the model are discussed.

Langhenry, M. T.↗
NASA NTRS1996

Accretion Disks in Supersoft X-ray Sources

We examine the role of the accretion disk in the steady-burning white dwarf model for supersoft sources. The accretion luminosity of the disk is quite small compared to the nuclear burning luminosity of the central source. Thus, in contrast to standard accretion disks, the main role of the disk is to reprocess the radiation from the white dwarf. We calculate models of accretion disks around luminous white dwarfs and compare the resulting disk fluxes to optical and UV observations of the LMC supersoft sources CAL 83, CAL 87, and RX J0513.9-6951. We find that if the white dwarf luminosity is near the upper end of the steady-burning region, and the flaring of the disk is included, then reprocessing by the disk can account for the UV fluxes and a substantial fraction of the optical fluxes of these systems. Reprocessing by the companion star can provide additional optical flux, and here too the disk plays an important role: since the disk is fairly thick, it shadows a significant fraction of the companion's surface.

Popham, Robert↗
NASA NTRS2014

Mean Flow Augmented Acoustics in Rocket Systems

Oscillatory motion in solid rocket motors and liquid engines has long been a subject of concern. Many rockets display violent fluctuations in pressure, velocity, and temperature originating from the complex interactions between the combustion process and gas dynamics. The customary approach to modeling acoustic waves inside a rocket chamber is to apply the classical inhomogeneous wave equation to the combustion gas. The assumption of a linear, non-dissipative wave in a quiescent fluid remains valid while the acoustic amplitudes are small and local gas velocities stay below Mach 0.2. The converging section of a rocket nozzle, where gradients in pressure, density, and velocity become large, is a notable region where this approach is not applicable. The expulsion of unsteady energy through the nozzle of a rocket is identified as the predominate source of acoustic damping for most rocket systems. An accurate model of the acoustic behavior within this region where acoustic modes are influenced by the presence of a steady mean flow is required for reliable stability predictions. Recently, an approach to address nozzle damping with mean flow effects was implemented by French [1]. This new approach extends the work originated by Sigman and Zinn [2] by solving the acoustic velocity potential equation (AVPE) formulated by perturbing the Euler equations [3]. The acoustic velocity potential (psi) describing the acoustic wave motion in the presence of an inhomogeneous steady high-speed flow is defined by, (del squared)(psi) − (lambda/c)(exp 2)(psi) − M(dot)[M(dot)(del)(del(psi))] − 2(lambda(M/c) + (M(dot)del(M))(dot)del(psi)−2(lambda)(psi)[M(dot)del(1/c)]=0 (1) with M as the Mach vector, c as the speed of sound, and lambda as the complex eigenvalue. French apply the finite volume method to solve the steady flow field within the combustion chamber and nozzle with inviscid walls. The complex eigenvalues and eigenvector are determined with the use of the ARPACK eigensolver. The present study employs the COMSOL Multphysics framework to solve the coupled eigenvalue problem using the finite element approach. The study requires one way coupling of the CFD High Mach Number Flow (HMNF) and mathematics module. The HMNF module evaluated the gas flow inside of a solid rocket motor using St. Robert's law modeling solid propellant burn rate, slip boundary conditions, and the supersonic outflow condition. Results from the HMNF model are used by the coefficient form of the mathematics module to determine the eigenvalues of the AVPE. The mathematics model is truncated at the nozzle sonic line, where a zero flux boundary condition is self-satisfying. The remaining boundaries are modeled with a zero flux boundary condition, assuming zero acoustic absorption on all surfaces. Pertinent results from these analyses are the complex valued eigenvalue and eigenvectors. Comparisons are made to the French results to evaluate the modeling approach. A comparison of the French results with that of the present analysis is displayed in figures 1 and 2, respectively. The graphic shows the first tangential eigenvector's real (a) and imaginary (b) values.

Fischbach, Sean R.↗
NASA NTRS2012

The Use of Satellite-Measured Aerosol Optical Depth to Constrain Biomass Burning Emissions Source Strength in a Global Model GOCART

Small particles in the atmosphere, called "atmospheric aerosol" have a direct effect on Earth climate through scattering and absorbing sunlight, and also an indirect effect by changing the properties of clouds, as they interact with solar radiation as well. Aerosol typically stays in the atmosphere for several days, and can be transported long distances, affecting air quality, visibility, and human health not only near the source, but also far downwind. Smoke from vegetation fires is one of the main sources of atmospheric aerosol; other sources include anthropogenic pollution, dust, and sea salt. Chemistry transport models (CTMs) are among the major tools for studying the atmospheric and climate effects of aerosol. Due to the considerable variation of aerosol concentrations and properties on many temporal and spatial scales, and the complexity of the processes involved, the uncertainties in aerosol effects on climate are large, as is featured in the latest report of Intergovernmental Panel on Climate Change (IPCC) in 2007. Reducing this uncertainty in the models is very important both for predicting future climate scenarios and for regional air quality forecasting and mitigation. During vegetation fires, also called biomass burning (BB) events, complex mixture of gases and particles is emitted. The amount of BB emissions is usually estimated taking into account the intensity and size of the fire and the properties of burning vegetation. These estimates are input into CTMs to simulate BB aerosol. Unfortunately, due to large variability of fire and vegetation properties, the quantity of BB emissions is very difficult to estimate and BB emission inventories provide numbers that can differ by up to the order of magnitude in some regions. Larger uncertainties in data input make uncertainties in model output larger as well. A powerful way to narrow the range of possible model estimates is to compare model output to observations. We use satellite observations of aerosol properties, specifically aerosol optical depth, which is directly proportional to the amount of aerosol in the atmosphere, and compare it to the model output. Assuming the model represents aerosol transport and particle properties correctly, the amount of BB emissions determines the simulated aerosol optical depth. In this study, we explore the regional performance of 13 commonly used emission estimates. These are each input to global Goddard Chemistry Aerosol Radiation and Transport (GOCART) model. We then evaluate how well each emission estimate reproduces the smoke aerosol optical depth measured by the MODIS instrument. We compared GOCART-simulate aerosol optical depth with that measured from the satellite for 124 fire cases around the world during 2006 and 2007. We summarize the regional performance of each emission inventory and discuss reasons for their differences by considering the assumptions made during their development. We also show that because stronger wind disperses smoke plumes more readily, in cases with stronger wind, a larger increase in emission amount is needed to increase aerosol optical depth. In quiet, low-wind-speed environments, BB emissions produce a more significant increase in aerosol optical depth, other things being equal. Using the region-specific, quantitative relationships derived in our paper, together with the wind speed obtained from another source for a given fire case, we can constrain the amount of emission required in the model to reproduce the observations. The results of this paper are useful to the developers of BB emission inventories, as they show the strengths and weaknesses of individual emission inventories in different regions of the globe, and also for modelers who use these inventories and wish to improve their model results.

Petrenko, Mariya↗