Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “buckling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The Role of Unit-Cell Topology in Modulating the Compaction Response of Additively Manufactured Cellular Materials using Simulations and Validation Experiments

Additive manufacturing has enabled a transformational ability to create cellular structures (or foams) with tailored topology. Compared to their monolithic polymer counterparts, cellular structures are potentially suitable for systems requiring materials with high specific energy-absorbing capability to provide enhanced damping. In this work, we demonstrate the utility of controlling unit-cell topology with the intent of obtaining a desired stress–strain response and energy density. Using mesoscale simulations that resolve the unit-cell sub-structures, we validate the role of unit-cell topology in selectively activating a buckling mode and thereby modulating the characteristic stress–strain response. Simulations incorporate a linear viscoelastic constitutive model and a hyperelastic model for simulating large deformation of the polymer under both tension and compression. Simulated results for nine different cellular structures are compared with experimental data to gain insights into three different modes of buckling and the corresponding stress–strain response.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Rapid approach for structural design of the tower and monopile for a series of 25 MW offshore turbines

The goal of further reducing the Levelized Cost of Energy (LCOE) has driven the investigation of large-scale wind turbines. This work presents a simple, rapid and detailed approach for the structural design of the tower and monopile without a controller, but with frequency and high fidelity structural verification. The approach uses an optimization to reduce the mass of the structures while meeting strength, buckling and geometric constraints by using analytical equations. A verification of frequency constraints is performed with BModes, and ANSYS Mechanical APDL is used for high fidelity verification of stress and buckling. The approach is applied to study the design space of three 25 MW offshore wind turbines with different rotor diameters and cone angles, and to evaluate the nacelle center of mass fore-aft location effect. Results obtained show that the tower and monopile are more susceptible to changes in the rotor thrust than the overturning moment even for designs with high pre-cone angle and large distance of the nacelle center of mass from the tower axis. But it is possible to obtain structurally feasible tower and monopile designs for the three 25 MW turbines studied while not exceeding diameter and wall thickness limits. However, mass penalties can be decreased by 0.8-14%, to further reduce the cost of energy, by increasing the diameter limit which may require manufacturing technology development. The approach applied and studies serve to understand the design space of the tower and monopile for a 25 MW turbine, and provide baseline designs that can be used in the development of a controller and evaluation of a full suite of design load cases.

17 WIND ENERGY↗
DOE OSTI2020

Double X/Peanut structures in barred galaxies – insights from an N -body simulation

ABSTRACT Boxy, peanut-, or X-shaped ‘bulges’ are observed in a large fraction of barred galaxies viewed in, or close to, edge-on projection, as well as in the Milky Way. They are the product of dynamical instabilities occurring in stellar bars, which cause the latter to buckle and thicken vertically. Recent studies have found nearby galaxies that harbour two such features arising at different radial scales, in a nested configuration. In this paper, we explore the formation of such double peanuts, using a collisionless N-body simulation of a pure disc evolving in isolation within a live dark matter halo, which we analyse in a completely analogous way to observations of real galaxies. In the simulation, we find a stable double configuration consisting of two X/peanut structures associated with the same galactic bar – rotating with the same pattern speed – but with different morphology, formation time, and evolution. The inner, conventional peanut-shaped structure forms early via the buckling of the bar, and experiences little evolution once it stabilizes. This feature is consistent in terms of size, strength, and morphology, with peanut structures observed in nearby galaxies. The outer structure, however, displays a strong X, or ‘bow-tie’, morphology. It forms just after the inner peanut, and gradually extends in time (within 1–1.5 Gyr) to almost the end of the bar, a radial scale where ansae occur. We conclude that, although both structures form, and are dynamically coupled to, the same bar, they are supported by inherently different mechanisms.

Ciambur, Bogdan C.↗
DOE OSTI2021

Local structure of Mott insulating iron oxychalcogenides La 2 O 2 Fe 2 OM2(M=S,Se)

Here, we describe the local structural properties of the iron oxychalcogenides, La 2 O 2 Fe 2 OM 2 (M=S,Se), by using pair distribution function analysis applied to total scattering data. Our results from neutron powder diffraction show that M = S and Se possess similar nuclear structures at low and room temperatures. The local crystal structures were studied by investigating deviations in atomic positions and the extent of the formation of orthorhombicity. Analysis of the total scattering data suggests that buckling of the Fe 2 O plane occurs below 100 K. The buckling may occur concomitantly with a change in octahedral height. Furthermore, within a typical range of 1-2 nm, we observed a short-range orthorhombiclike structure suggestive of nematic fluctuations in both of these materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Sensitivity of electronic structure to crystal distortions in infinite-layered LaNiO 2

Recent observations of unconventional superconductivity (SC) in thin films of LaNiO 2 (critical temperature T c ≃ 10 K) and in bulk single crystals of La 3 ⁢Ni 2 ⁢O 7 under pressure T c ≃ 80K have cemented a long sought-after class of SC nickelates. In La 1–x ⁢Sr⁢ x ⁢NiO 2 , SC appears only in films for reasons not understood. We perform a combination of experiments to probe the crystal structure and magnetic order in bulk LaNiO 2 together with ab initio calculations of the electronic structure. We find that the infinite layers are naturally buckled out-of-plane. The electronic bands are largely unaffected by the buckling, but uniaxial compression along the c axis may lead to a Lifshitz transition.

36 MATERIALS SCIENCE↗
DOE OSTI2020

On the Cutting of Metals: A Mechanics Viewpoint

The mechanics of large-strain deformation in cutting of metals is discussed, primarily from viewpoint of recent developments in in situ analysis of plastic flow and microstructure characterization. It is shown that a broad range of deformation parameters can be accessed in chip formation—strains of 1–10, strain rates of 10–10 5 /s, and temperatures up to 0.7T m —and controlled. This range is far wider than achievable by any other single-stage, severe plastic deformation (SPD) process. The resulting extreme deformation conditions produce a rich variety of microstructures in the chip. Four principal types of chip formation—continuous, shear-localized, segmented, and mushroom-type—as elucidated first by Nakayama (1974, “The Formation of ‘Saw-Toothed Chip’ in Metal Cutting,” Proceedings of International Conference on Production Engineering, Tokyo, pp. 572–577) are utilized to emphasize the diverse plastic flow phenomena, especially unsteady deformation modes that prevail in cutting. These chip types are intimately connected with the underlying flow, each arising from a distinct mode and triggered by an instability phenomenon. The role of plastic flow instabilities such as shear banding, buckling, and fracture in mediating unsteady flow modes is expounded, along with consequences of the flow modes and chip types for the cutting. Sinuous flow is shown to be the reason why gummy (highly strain-hardening) metals, although relatively soft, are so difficult to cut. Synthesizing the various observations, a hypothesis is put forth that it is the stability of flow modes that determines the mechanics of cutting. Furthermore, this leads to a flow-stability phase diagram that could provide a framework for predicting chip types and process attributes.

42 ENGINEERING↗
DOE OSTI2021

Pipeline Structural Stability Under Nuclear Blast Pressure Loading

This report documents a set of simplified models to predict pipeline collapse under nuclear pressure loading. After a review of pipeline design literature, a set of simple expressions have been selected to represent an approximation of the threshold pressure for failure from cross- sectional yielding, cross-section buckling, and longitudinal buckling. These expressions provide a first-order approximation on load levels needed to achieve collapse. As a demonstration, the collapse pressure for a set of representative pipelines are calculated. Estimated pressure fields are also computed for a set of nuclear detonations, providing estimates of the ground range limit for pipeline collapse.

42 ENGINEERING↗
DOE OSTI2024

The role of unit cell topology in modulating the compaction response of additively manufactured cellular materials using simulations and validation experiments

Additive manufacturing has enabled a transformational ability to create cellular structures (or foams) with tailored topology. Compared to their monolithic polymer counterparts, cellular structures are potentially suitable for systems requiring materials with high specific energy-absorbing capability to provide enhanced damping. In this work, we demonstrate the utility of controlling unit-cell topology with the intent of obtaining a desired stress–strain response and energy density. Using mesoscale simulations that resolve the unit-cell sub-structures, we validate the role of unit-cell topology in selectively activating a buckling mode and thereby modulating the characteristic stress–strain response. Simulations incorporate a linear viscoelastic constitutive model and a hyperelastic model for simulating large deformation of the polymer under both tension and compression. Simulated results for nine different cellular structures are compared with experimental data to gain insights into three different modes of buckling and the corresponding stress–strain response.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Realizing the Materials-Designed-To-Environments Promise of Additive Manufacturing Through a Fundamentally Different Approach to Optimization of Nonlinear Solid Mechanics Structures

Additive Manufacturing (AM) is expected to play a large role in the labs-wide goals of accelerating innovation and leading in modern engineering. More specifically, AM is seen as a key enabling technology for increasing the agility of nuclear deterrence and other national security applications involving complex coupled environments. However, the impact of AM on these initiatives has not been as wide-ranging as hoped because – despite its unique qualities – the focus has mostly been on detailed qualification to force AM components into pre-existing performance envelopes. This paradigm fundamentally precludes the novel possibilities afforded by the geometric and material flexibility of AM. In particular, the engineering of small-scale features to undergo buckling and contact can cause large geometric and symmetry changes which provide responsiveness to different environments. Despite almost a decade of observing such behavior, there exists no way to systematically design for AM to exploit it. Our goal for this project was to connect material design to multi-environment component performance by reconceptualizing how to design for AM to exploit the buckling and contact of small-scale features.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Revisiting the capacity-fading mechanism of P2-type sodium layered oxide cathode materials during high-voltage cycling

We report P2-type sodium layered oxide cathode (Na 2/3 Ni 1/3 Mn 2/3 O 2 , P2-NNMO) has attracted great attention as a promising cathode material for sodium ion batteries because of its high specific capacity. However, this material suffers from a rapid capacity fade during high-voltage cycling. Several mechanisms have been proposed to explain the capacity fade, including intragranular fracture caused by the P2-O2 phase transion, surface structural change, and irreversible lattice oxygen release. Here we systematically investigated the morphological, structural, and chemical changes of P2-NNMO during high-voltage cycling using a variety of characterization techniques. It was found that the lattice distortion and crystal-plane buckling induced by the P2-O2 phase transition slowed down the Na-ion transport in the bulk and hindered the extraction of the Na ions. The sluggish kinetics was the main reason in reducing the accessible capacity while other interfacial degradation mechanisms played minor roles. Our results not only enabled a more complete understanding of the capacity-fading mechanism of P2-NNMO but also revealed the underlying correlations between lattice doping and the moderately improved cycle performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Leaf morphogenesis: The multifaceted roles of mechanics

Plants produce a rich diversity of biological forms, and the diversity of leaves is especially notable. Mechanisms of leaf morphogenesis have been studied in the past two decades, with a growing focus on the interactive roles of mechanics in recent years. Growth of plant organs involves feedback by mechanical stress: growth induces stress, and stress affects growth and morphogenesis. Although much attention has been given to potential stress-sensing mechanisms and cellular responses, the mechanical principles guiding morphogenesis have not been well understood. Here we synthesize the overarching roles of mechanics and mechanical stress in multilevel and multiple stages of leaf morphogenesis, encompassing leaf primordium initiation, phyllotaxis and venation patterning, and the establishment of complex mature leaf shapes. Moreover, the roles of mechanics at multiscale levels, from subcellular cytoskeletal molecules to single cells to tissues at the organ scale, are articulated. In conclusion, by highlighting the role of mechanical buckling in the formation of three-dimensional leaf shapes, this review integrates the perspectives of mechanics and biology to provide broader insights into the mechanobiology of leaf morphogenesis.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Additive Manufacturing of Thermal Energy Storage Composites with Microencapsulated Phase Change Materials Supported in a Multipolymer Matrix

Additive manufacturing (AM) techniques to directly integrate phase change materials (PCMs) are of interest for efficient thermal energy storage (TES) architectures. Complex, high surface-to-volume ratio composites embedded with PCM can improve thermal management with reduced material waste for customizable device fabrication. Reducing feature sizes of TES-integrated heat exchangers using AM can increase heat transfer without thermal conductivity enhancement. Here, composite AM materials containing 60 wt% microencapsulated phase change materials (MEPCM) are fabricated using off-the-shelf printers at common speeds and resolutions. High MEPCM loading in filaments is achieved with powder extrusion using two polymers, thermoplastic-polyurethane (TPU) and polycaprolactone (PCL), that mediate flexibility and rigidity for effective extrusion and printing without filament fracture or buckling. Furthermore, with PCL and TPU at 20 wt% each and 60 wt% MEPCM (P 20 T 20 M 60 ), smooth, form-stable filaments are consistently printed. Powder-based extrusion displays negligible damaging effects on the MEPCM. Printed P 20 T 20 M 60 demonstrates 105 J/g of energy storage with no degradation through 250 thermal cycles, within 5% of the theoretical storage enthalpy. Combining PCL/TPU shows good interfacial adhesion between print layers and produces high surface area objects, like 15% gyroids, and dense, 100% infilled pucks. Prints are also scalable to a 900 cm 3 honeycomb heat exchanger with an estimated 9 Wh energy storage.

25 ENERGY STORAGE↗
DOE OSTI2021

Zero-Valent Palladium Single-Atoms Catalysts Confined in Black Phosphorus for Efficient Semi-Hydrogenation

Single-atom catalysts (SACs) represent a new frontier in heterogeneous catalysis due to their remarkable catalytic properties and maximized atomic utilization. However, single atoms often bond to the support with polarized electron density and thus exhibit a high valence state, limiting their catalytic scopes in many chemical transformations. In this study, it is demonstrated that 2D black phosphorus (BP) acts as giant phosphorus (P) ligand to confine a high density of single atoms (e.g., Pd 1 , Pt 1 ) via atomic layer deposition. Unlike other 2D materials, BP with relatively low electronegativity and buckled structure favors the strong confinement of robust zero-valent palladium SACs in the vacancy site. Metallic Pd 1 /BP SAC shows a highly selective semi-hydrogenation of phenylacetylene toward styrene, distinct from metallic Pd nanoparticles that facilitate the formation of fully hydrogenated products. Density functional theory calculations reveal that Pd atom forms covalent-like bonding with adjacent P atoms, wherein H atoms tend to adsorb, aiding the dissociative adsorption of H 2 . Zero-valent Pd in the confined space favors a larger energy gain for the synthesis of partially hydrogenated product over the fully hydrogenated one. This work provides a new route toward the synthesis of zero-valent SACs on BP for organic transformations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multimaterial 3D Printing in Activating Bath Enables In Situ Polymerization of Thermosets with Intricate Geometries and Diverse Elastic Behaviors

Polydicyclopentadiene, p(DCPD), is a high‐performance thermoset valued for its exceptional toughness, strength, and stiffness. When copolymerized with 1,5‐cyclooctadiene (COD), its mechanical properties can be tuned from glassy to rubbery at room temperature. While frontal polymerization enables a rapid and energy‐efficient route to 3D print DCPD‐based materials, challenges such as ink shelf life and gravitational distortion, especially in direct ink writing of soft COD‐rich formulations, must be considered. Here, a complementary chemical strategy is presented, embedded 3D printing, that enables localized in situ polymerization of printed DCPD/COD inks within a reactive support matrix. The matrix provides both physical support and a reservoir of chemical activator, which diffuses into the ink, activates a latent bis(N‐heterocyclic carbene) Ru precatalyst, and initiates ring‐opening metathesis polymerization. Curing begins at the ink–matrix interface and propagates inward via diffusion, stabilizing the interface and preventing capillary‐driven deformation regardless of the matrix yield stress. This approach eliminates the need for cold storage, external curing, or photoinitiation, significantly expanding the processing window. Using this method, diverse thermosetting and elastomeric architectures are fabricated with features as small as 5 µm and aspect ratios of 100, including interlinked chains, shallow spherical shells exhibiting snap‐through buckling, and hair‐like fin arrays inaccessible through traditional techniques.

chemical activation↗
DOE OSTI2024

Tunable Metamaterials for Impact Mitigation

Traditional methods of shielding fragile goods and human tissues from impact energy rely on isotropic foam materials. The mechanical properties of these foams are inferior to an emerging class of metamaterials called plate lattices, which have predominantly been fabricated in simple 2.5-dimensional geometries using conventional methods that constrain the feasible design space. Here in this work, additive manufacturing is used to relax these constraints and realize plate lattice metamaterials with nontrivial, locally varying geometry. The limitations of traditional computer-aided design tools are circumvented and allow the simulation of complex buckling and collapse behaviors without a manual meshing step. By validating these simulations against experimental data from tests on fabricated samples, sweeping exploration of the plate lattice design space is enabled. Numerical and experimental tests demonstrate plate lattices absorb up to six times more impact energy at equivalent densities relative to foams and shield objects from impacts ten times more energetic while transmitting equivalent peak stresses. In contrast to previous investigations of plate lattice metamaterials, designs with nonuniform geometric prebuckling in the out-of-plane direction is explored and showed that these designs exhibit 10% higher energy absorption efficiency on average and 25% higher in the highest-performing design.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Catalytic Oxidation of CO on a Curved Pt(111) Surface: Simultaneous Ignition at All Facets through a Transient CO-O Complex

The light-off of the CO oxidation is simultaneous on all Pt crystal surfaces vicinal to the (111) plane, regardless of the reaction conditions, and in contrast with the structural dependence of Pd. In this work, using ambient-pressure XPS we find that, immediately prior to ignition, atomic oxygen incorporates to the subsurface plane, leading to buckling of the topmost CO-Pt layer, and effectively equaling the CO desorption temperature at terraces and steps.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Synchrotron CT imaging of lattice structures with engineered defects

Understanding mechanical failure, crack propagation, and compressive behavior at the micrometer scale is essential for tailoring material properties for structural performance in cellular materials. Typically, modeling of traditional polymer foam materials is clouded by the lack of control in material morphology and its inherent stochastic structure. Additive manufacturing with sub-micrometer resolution provides a direct path for experimenters to specifically tailor structures needed by modelers to explicitly probe mechanical performance. Using laboratory-based 3D X-ray computed tomographic imaging (CT), the examination of deformation and damage provides a critical path to understand how these soft materials behave. Additionally, synchrotron CT yields realistic information at higher strain rates to directly validate the robustness of our finite element modeling. For this study, nanolithographic printing was employed to generate a series of engineered lattices with increasing levels of defects through the random removal of ligaments. These structures were mechanically tested and imaged with laboratory-based microCT. Additionally, synchrotron experiments were conducted in which the structures were imaged in 3D at 14 Hz during compression at a 0.4 s –1 strain rate. These 3D images show the changes in the structure as the ligaments bend, buckle and fracture in real time. This technique provides a robust framework for developing our methodologies and future exploration of engineered structures.

36 MATERIALS SCIENCE↗