Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “brush”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Brush Seals for Cryogenic Applications: Performance, Stage Effects, and Preliminary Wear Results in LN2 and LH2

Brush seals are compliant contacting seals and have significantly lower leakage than labyrinth seals in gas turbine applications. Their long life and low leakage make them candidates for use in rocket engine turbopumps. Brush seals, 50.8 mm (2 in.) in diameter with a nominal 127-micron (0.005-in.) radial interference, were tested in liquid nitrogen (LN2) and liquid hydrogen (LH2) at shaft speeds up to 35,000 and 65,000 rpm, respectively, and at pressure drops up to 1.21 MPa (175 psid) per brush. A labyrinth seal was also tested in liquid nitrogen to provide a baseline. The LN2 leakage rate of a single brush seal with an initial radial shaft interference of 127 micron (0.005 in.) measured one-half to one-third the leakage rate of a 12-tooth labyrinth seal with a radial clearance of 127 micron (0.005 in.). Two brushes spaced 7.21 micron (0.248 in.) apart leaked about one-half as much as a single brush, and two brushes tightly packed together leaked about three-fourths as much as a single brush. The maximum measured groove depth on the Inconel 718 rotor with a surface finish of 0.81 micron (32 microinch) was 25 micron (0.0010 in.) after 4.3 hr of shaft rotation in liquid nitrogen. The Haynes-25 bristles wore approximately 25 to 76 micron (0.001 to 0.003 in.) under the same conditions. Wear results in liquid hydrogen were significantly different. In liquid hydrogen the rotor did not wear, but the bristle material transferred onto the rotor and the initial 127 micron (0.005 in.) radial interference was consumed. Relatively high leakage rates were measured in liquid hydrogen. More testing is required to verify the leakage performance, to validate and calibrate analysis techniques, and to determine the wear mechanisms. Performance, staging effects, and preliminary wear results are presented.

Proctor, Margaret P.↗

Rotating Brush Seal

The proven technology of brush seals has been extended to the mitigation of problems arising from friction and wear at the bristle-rotor interface at high surface speeds. In prototype testing, the brush is mounted on, and free to rotate with the shaft, thus providing a complaint primary seal. A face seal positioned between the backing plate of the brush seal and the housing provides a secondary seal. The purpose of this paper is to demonstrate the interaction between the brush bristles and the shaft at high surface speeds as well as introduce a numerical model to simulate the bristle behavior. A test facility was constructed to study the effects of centrifugal forces on bristle deflection in a single rotating brush seal. The bristle-rotor interface was observed through a video camera, which utilized a high magnification borescope and a high frequency strobe light source. Rotational speeds of the rotor and the brush seal were measured by a magnetic and optical speed sensor, respectively. Preliminary results with speeds up to 11,000 rpm show no speed differential between the brush seal and rotor, or any instability problems associated with the brush seal. Bristle liftoff from the rotor is successfully captured on video.

Lattime, S. B.↗

Brush-Wheel Samplers for Planetary Exploration

A report proposes brush-wheel mechanisms for acquiring samples of soils from remote planets. In simplest terms, such a mechanism would contain brush wheels that would be counter-rotated at relatively high speed. The mechanism would be lowered to the ground from a spacecraft or other exploratory vehicle. Upon contact with the ground, the counter-rotating brush wheels would kick soil up into a collection chamber. Thus, in form and function, the mechanism would partly resemble traditional street and carpet sweepers. The main advantage of using of brush wheels (in contradistinction to cutting wheels or other, more complex mechanisms) is that upon encountering soil harder than expected, the brushes could simply deflect and the motor(s) could continue to turn. That is, sufficiently flexible brushes would afford resistance to jamming and to overloading of the motors used to rotate the brushes, and so the motors could be made correspondingly lighter and less power hungry. Of course, one could select the brush stiffnesses and motor torques and speeds for greatest effectiveness in sampling soil of a specific anticipated degree of hardness.

Rivellini, Tommaso↗

Comparison of brush and biopsy sampling methods of the ileal pouch for assessment of mucosa-associated microbiota of human subjects

Mucosal biopsy is the most common sampling technique used to assess microbial communities associated with the intestinal mucosa. Biopsies disrupt the epithelium and can be associated with complications such as bleeding. Biopsies sample a limited area of the mucosa, which can lead to potential sampling bias. In contrast to the mucosal biopsy, the mucosal brush technique is less invasive and provides greater mucosal coverage, and if it can provide equivalent microbial community data, it would be preferable to mucosal biopsies. Results: We compared microbial samples collected from the intestinal mucosa using either a cytology brush or mucosal biopsy forceps. We collected paired samples from patients with ulcerative colitis (UC) who had previously undergone colectomy and ileal pouch anal anastomosis (IPAA), and profiled the microbial communities of the samples by sequencing V4-V6 or V4-V5 16S rRNA-encoding gene amplicons. Comparisons of 177 taxa in 16 brush-biopsy sample pairs had a mean R2 of 0.94. We found no taxa that varied significantly between the brush and biopsy samples after adjusting for multiple comparisons (false discovery rate ≤0.05). We also tested the reproducibility of DNA amplification and sequencing in 25 replicate pairs and found negligible variation (mean R2 = 0.99). A qPCR analysis of the two methods showed that the relative yields of bacterial DNA to human DNA were several-fold higher in the brush samples than in the biopsies. Conclusions: Mucosal brushing is preferred to mucosal biopsy for sampling the epithelial-associated microbiota. Although both techniques provide similar assessments of the microbial community composition, the brush sampling method has relatively more bacterial to host DNA, covers a larger surface area, and is less traumatic to the epithelium than the mucosal biopsy.

59 BASIC BIOLOGICAL SCIENCES↗

Ionic current in nanochannels grafted with pH-responsive polyelectrolyte brushes modeled using augmented strong stretching theory

Here, we provide a theory to quantify the ionic current (i ion ) in nanochannels grafted with pH-responsive polyelectrolyte (PE) brushes. We consider the PE brushes to be modelled by our recently proposed augmented strong stretching theory (SST) model that improves the existing SST models by incorporating the effects of excluded volume interactions and an extended mass action law. Use of such augmented SST for this problem implies that this is the first study on computing i ion in PE-brush-grafted nanochannels accounting for the appropriate coupled con guration-electrostatic description of the PE brushes. i ion is obtained as functions of PE brush grafting density, medium pH and salt concentration (c ∞ ), and the density of polyelectrolyte chargeable sites (PECS). For large c ∞ , i ion increases linearly with c ∞ (as for such c ∞ , i ion becomes independent of the PE charge and is dominated by the bulk mobility and number density of the electrolyte ions), while iion is independent of c ∞ at small c ∞ (where the EDL electrostatics and the total number of ions in the system is dominated by the hydrogen ions). We further witness an enhancement of i ion for smaller pH and larger grafting density at low and moderate c ∞ , while there is little to no effect of the PECS density on the ionic current except for weakly grafted brushes at low c ∞ . We believe that this study will serve as a theoretical foundation for a large number of applications that are based on the brush-induced modification of the ionic current in a nanochannel.

42 ENGINEERING↗

The effect of multivalent counterions to the structure of highly dense polystyrene sulfonate brushes

Surface tethered polyelectrolyte brushes are scientifically interesting and technologically relevant to many applications, ranging from colloidal stabilization to responsive and tunable materials to lubrication. Many applications operate in environments containing multi-valent ions, media in which our scientific understanding is not yet well-developed. In this paper, we synthesized high-density polystyrene sulfonate (PSS) brushes via surface initiated atom-transfer radical polymerization, and performed neutron reflectivity (NR) measurements to investigate and compare the effects of mono-valent Rb + and tri-valent Y 3+ counterions to the structure of the densely tethered PSS brushes. Our NR results show that in mono-valent RbNO 3 solution, the dense PSS brush retained its full thickness up to a salt concentration of 1 M, whereas it immediately collapsed upon adding 1.67 mM of tri-valent Y 3+ . Increasing the concentration of Y 3+ beyond this level did not lead to any significant further structure change of the PSS brush. Finally, our findings demonstrate that the presence of multi-valent counterions can significantly alter the structure of polyelectrolyte brushes, in a manner different from mono-valent ions, which has implications for the functionality of the brushes.

36 MATERIALS SCIENCE↗

Shape-Persistent, Thermoresponsive Polypeptide Brushes Prepared by Vapor Deposition Surface-Initiated Ring-Opening Polymerization of α-Amino Acid N -Carboxyanhydrides

We report that surface-grafting thermoresponsive polymers allows the preparation of thin polymer brush coatings with surface properties that can be manipulated by variation of temperature. In most instances, thermoresponsive polymer brushes are produced using polymers that dehydrate and collapse above a certain temperature. This report presents the preparation and properties of polymer brushes that show thermoresponsive surface properties, yet are shape-persistent in that they do not undergo main chain collapse. The polymer brushes presented here are obtained via vapor deposition surface-initiated ring-opening polymerization (SI-ROP) of γ-di- or tri(ethylene glycol)-modified glutamic acid N-carboxyanhydrides. Vapor deposition SI-ROP of γ-di- or tri(ethylene glycol)-modified L- or D-glutamic acid N-carboxyanhydrides affords helical surface-tethered polymer chains that do not show any changes in secondary structure between 10 and 70 °C. QCM-D experiments, however, revealed significant dehydration of poly(γ-(2-(2-methoxyethoxy)ethyl)-l-glutamate) (poly(L-EG 2 -Glu)) brushes upon heating from 10 to 40 °C. At the same time, AFM and ellipsometry studies did not reveal significant variations in film thickness over this temperature range, which is consistent with the shape-persistent nature of these polypeptide brushes and indicates that the thermoresponsiveness of the films is primarily due to hydration and dehydration of the oligo(ethylene glycol) side chains. The results we present here illustrate the potential of surface-initiated NCA ring-opening polymerization to generate densely grafted assemblies of polymer chains that possess well-defined secondary structures and tunable surface properties. These polypeptide brushes complement their conformationally unordered counterparts that can be generated via surface-initiated polymerization of vinyl-type monomers and represent another step forward to biomimetic surfaces and interfaces.

36 MATERIALS SCIENCE↗

Molecular Simulations of the Hydration Behavior of a Zwitterion Brush Array and Its Antifouling Property in an Aqueous Environment

We carried out umbrella sampling and molecular dynamics (MD) simulations to investigate molecular interactions between sulfobetaine zwitterions or between sulfobetaine brushes in different media. Simulation results show that it is more energetically favorable for the two sulfobetaine zwitterions or brushes to be fully hydrated in aqueous solutions than in vacuum where strong ion pairs are formed. Structural properties of the hydrated sulfobetaine brush array and its antifouling behavior against a foulant gel are subsequently studied through steered MD simulations. We find that sulfobetaine brush arrays with different grafting densities have different structures and antifouling mechanisms. At a comparably higher grafting density, the sulfobetaine brush array exhibits a more organized structure which can hold a tightly bound hydration water layer at the interface. Compression of this hydration layer results in a strong repulsive force. However, at a comparably lower grafting density, the brush array exhibits a randomly oriented structure in which the antifouling of the brush array is through the deformation of the sulfobetaine branches.

36 MATERIALS SCIENCE↗

Enrichment and Distribution of Pb 2+ Ions in Zwitterionic Poly(cysteine methacrylate) Brushes at the Solid–Liquid Interface

Cysteine-based polyzwitterionic brushes have been prepared via a two-step route. First, poly(allyl methacrylate) (PAMA) brushes have been grown from the surface of silicon substrates using surface-initiated atom transfer radical polymerization. The obtained PAMA brushes with free pendant vinyl groups were further modified via radical thiol-ene addition reaction to attach L-cysteine moieties. Surface zeta potential investigations on pH-responsiveness of these poly(cysteine methacrylate) (PCysMA) brushes confirm their zwitterionic character at intermediate pH range, while at pH values either below pH 3.50 or above pH 8.59, they exhibit polyelectrolyte character. Under acid (pH < 3.50) or base (pH > 8.59) conditions, they possess either cationic or anionic character, respectively. In the zwitterionic region, these PCysMA brushes show positive surface $\zeta$ potential in the presence of Pb(CH 3 COO) 2 solutions of various concentrations. The results are in line with microscopic investigations using anomalous X-ray reflectivity (AXRR) carried out along the absorption edge of Pb 2+ ions. When the photon energies were varied around the absorption L3 edge of lead (13037 eV), the Pb 2+ concentration normal to the silicon substrates, as a function of depth inside PCysMA brushes, could be revealed at the nanoscale. Both zeta potential and AXRR measurements confirm the enrichment of Pb 2+ ions inside PCysMA brushes, indicating the potential of PCysMA to be used as a water purification material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Combined Machine Learning and Molecular Dynamics Reveal Two States of Hydration of a Single Functional Group of Cationic Polymeric Brushes

The state of hydration of a macromolecular system regulates a plethora of different properties of such a system. In this article, we develop a novel machine learning (ML) approach, based on the unsupervised clustering algorithm, for probing the hydration behavior of the {N(CH 3 ) 3 } + functional group of the PMETAC [Poly(2-(methacryloyloxy)ethyl trimethylammonium chloride] polyelectrolyte (PE) brush system. The PE brushes and the brush-supported water molecules and counterions (chloride ions) are first described using all-atom molecular dynamics (MD) simulations. The simulation data is subsequently used in our ML framework to identify that (1) the {N(CH 3 ) 3 } + functional groups of the PMETAC brushes have two distinct hydration states with one state (state 1) being characterized by less structured water molecules and the other state (state 2) being characterized by more structured water molecules and (2) an enhancement in the brush grafting density leads to the progressive dissapparenace of state 2. An increase in the grafting density increases the number of chloride counterions in a given volume around the {N(CH 3 ) 3 } + functional group and increases the number of shared water molecules between the {N(CH 3 ) 3 } + and Cl - . The chloride counterions are associated with a hydration layer with much less structured water molecules. Therefore, with an increase in the grafting density, an increase in the percentage of shared water molecules leads to the prevalence of the hydration state [of the {N(CH 3 ) 3 } + moiety] with less structured water molecules. Finally, we explain how the present findings are commensurate with two key previous related results, namely a significantly large chloride ion mobility inside the PMETAC brush layer and the {N(CH 3 ) 3 } + -Cl - average distance remaining independent of the PMETAC brush grafting density. Furthermore, we anticipate that the combined ML-MD-simulation approach proposed in this study can be adapted to probe other soft matter systems to reveal new insights of the underlying mechanisms of emergent phenomenon.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Lateral Structure Formation in Polyelectrolyte Brushes Induced by Multivalent Ions

We provide a theoretical model for the collapse of polyelectrolyte brushes in the presence of multivalent ions, focusing on the formation of lateral inhomogeneties in the collapsed state. Polyelectrolyte brushes are important in a variety of applications, including stabilizing colloidal particles and lubricating surfaces. Many uses rely on the extension of the densely grafted polymer chains from the surface in the extended brush morphology. In the presence Extended Brush of multivalent ions, brushes are significantly shorter than in monovalent ionic solutions, which greatly affects their properties. We base our theoretical analysis on an analogous collapse of polyelectrolyte brushes in a poor solvent, providing an energy balance representation for pinned micelles and cylindrical bundles. The equilibrium brush heights predicted for these structures are of a similar magnitude to those measured experimentally. The formation of lateral structures can open new avenues for stimuli-responsive applications that rely on nanoscale pattern formation on surfaces.

Brettmann, Blair↗

Comparing solvophobic and multivalent induced collapse in polyelectrolyte brushes

Here, coarse-grained molecular dynamics enhanced by free-energy sampling methods is used to examine the roles of solvophobicity and multivalent salts on polyelectrolyte brush collapse. Specifically, we demonstrate that while ostensibly similar, solvophobic collapsed brushes and multivalent-ion collapsed brushes exhibit distinct mechanistic and structural features. Notably, multivalent-induced heterogeneous brush collapse is observed under good solvent polymer backbone conditions, demonstrating that the mechanism of multivalent collapse is not contingent upon a solvophobic backbone. Umbrella sampling of the potential of mean-force (PMF) between two individual brush strands confirms this analysis, revealing starkly different PMFs under solvophobic and multivalent conditions, suggesting the role of multivalent “bridging” as the discriminating feature in trivalent collapse. Structurally, multivalent ions show a propensity for nucleating order within collapsed brushes, whereas poor-solvent collapsed brushes are more disordered; this difference is traced to the existence of a metastable PMF minimum for poor solvent conditions, and a global PMF minimum for trivalent systems, under experimentally relevant conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Grafting density effects, optoelectrical properties and nano-patterning of poly(para-phenylene) brushes

Well-defined conjugated polymers in confined geometries are challenging to synthesize and characterize, yet they are potentially useful in a broad range of organic optoelectronic devices such as transistors, light emitting diodes, solar cells, sensors, and nanocircuits. We report a systematic study of optoelectrical properties, grafting density effects, and nanopatterning of a model, end-tethered conjugated polymer system. Specifically, poly(para-phenylene) (PPP) brushes of various grafting density are created in situ by aromatizing well-defined, end-tethered poly(1,3-cyclohexadiene) (PCHD) “precursor brushes”. Furthermore, this novel precursor brush approach provides a convenient way to make and systematically control the grafting density of high molecular weight conjugated polymer brushes that would otherwise be insoluble. Finally, this allows us to examine how grafting density impacts the effective conjugation length of the conjugated PPP brushes and to adapt the fabrication method to develop spatially patterned conjugated brush systems, which is important for practical applications of conjugated polymer brushes.

36 MATERIALS SCIENCE↗

Engineering the anchoring behavior of nematic liquid crystals on a solid surface by varying the density of liquid crystalline polymer brushes

Controlling the orientation of liquid crystal (LC) molecules towards contacting surfaces is a crucial requirement for the development of LC displays and passive electro-optical devices. Up to now, research has been focused on photo-responses of a LC azobenzene polymer system to obtain either planar or homeotropic orientation of LCs. It remains a challenge, however, to tune the polar angle of LC molecules on the solid surface and gain more insights about the polymer chain conformation extending in LC medium. Here, we deposit a liquid crystalline side chain polymer brush, poly(6-(4-methoxy-azobenzene-4'-oxy)hexyl methacrylate) (PMMAZO), onto the solid surface with film thickness varying between ~3 nm and 13 nm; therefore, the grafting density of the brush layer ranges from 0.0219 to 0.0924 chains per nm 2 . When LCs are confined in hybrid cells with a top surface eliciting uniform homeotropic anchoring and a bottom surface covered by the PMMAZO brush, the out-of-plane polar angle of 4-pentyl-4'-cyanobiphenyl (5CB) on the brush layer gradually changes from ~0° to ~62° by simply increasing the grafting brush density. The surface forces apparatus (SFA) measurement is used to determine 5CB as a good solvent for the PMMAZO brush and understand the relationship between the chain conformation in 5CB and the anchoring behavior of LC molecules on the polymer brush layer. Here, for high grafting density, the polymer chain in 5CB extends significantly away from the substrate, making the side chain mesogens on average almost parallel to the substrate; for the low-density case, the main chain extends in the narrow region around the surface for aligning the mesogens perpendicular to the substrate.

36 MATERIALS SCIENCE↗

Design optimization of a brush turbine with a cleaner/water based solution

Recently, a fluid turbine which has a brush attached to it has been designed and tested with water as fluid. The purpose of the turbine-brush is to clean up fouling in a tube. The Montreal Protocol prohibits the use of CFC products from refrigeration industry or from industry in general as a cleanser in 1996. Alternatives for the cleansers, devices or a combination of alternative devices with a cleanser should be found. One of the methods is to develop a device which cleans fouling with a cleaning medium. In this paper, we describe a turbine connected with a brush. However, the turbine with the brush should be simple and easy to install. This device is a combined small liquid turbine with a brush. The turbine is activated by the liquid flowing through the tube. Then the turbine turns the brush cleaning fouling along the tube. Based on the energy conservation and the Bernoulli equation along with an empirical relationship of drag force obtained from an experimental apparatus, a relationship of the rotational speed, the number of blades, and geometric variables of the turbine-brush was obtained. The predicted rotational speeds were compared with the experimental observations. Further work was recommended for improvements.

Kim, Rhyn H.↗

Brush Seals for Improved Steam Turbine Performance

GE Energy has retrofitted brush seals into more than 19 operating steam turbines. Brush seals offer superior leakage control compared to labyrinth seals, owing to their compliant nature and ability to maintain very tight clearances to the rotating shaft. Seal designs have been established for steam turbines ranging in size from 12 MW to over 1200 MW, including fossil, nuclear, combined-cycle and industrial applications. Steam turbines present unique design challenges that must be addressed to ensure that the potential performance benefits of brush seals are realized. Brush seals can have important effects on the overall turbine system that must be taken into account to assure reliable operation. Subscale rig tests are instrumental to understanding seal behavior under simulated steam-turbine operating conditions, prior to installing brush seals in the field. This presentation discusses the technical challenges of designing brush seals for steam turbines; subscale testing; performance benefits of brush seals; overall system effects; and field applications.

Turnquist, Norman↗

Brush-Modified Materials: Control of Molecular Architecture, Assembly Behavior, Properties and Applications

Recent progress in surface-initiated polymerization enables the deliberate polymer modification of nanoscopic surfaces with high levels of precision. This has given rise to the development of brush particle-based materials (sometimes referred to as ‘hairy nanoparticles’) that are formed by tethering of polymer chains to the surface of nanoparticle-like objects. Brush particles have attracted interest as model systems to understand the effect of surface modification on the structure and interactions in polymer modified colloidal systems (which play a role across fields as diverse as functional coatings, cosmetics, foods or pharmaceuticals) but also as building blocks for the assembly of ‘one-component hybrid materials’ that exhibit unprecedented property combinations, not realizable in classical composite materials. This review presents a summary and analysis of the developments in the field of ‘particle brush materials’. The evolution of synthetic methodologies from the original pioneering work to emerging trends and opportunities in the field of brush synthesis is presented first. Subsequently, the effect of brush architecture on the structure, interaction and assembly of brush particles both with and without a matrix is discussed. Lastly, recent advances in the development of functional hybrid materials with applications in energy, catalysis, sensing and other areas is presented.

36 MATERIALS SCIENCE↗

Influence of Grafting Density and the Ionic Environment on the Structure of Zwitterionic Brushes

Zwitterionic polymer brushes possess a high potential for applications as surface coatings, e.g., in antifouling applications. Their complex association behavior due to the coexistence of oppositely charged groups on the same monomeric unit allows for a broad variation of polarity, hydrophilicity, and the antipolyelectrolyte effect with the variation of the surrounding environment. In this study, planar polysulfobetaine brushes were investigated with neutron reflectometry (NR) and neutron spin–echo spectroscopy under grazing incidence (GINSES) to explore the brush structure and its inner dynamics perpendicular to the substrate. In particular, the effects of the substrate–initiator system and ionic strength on the structure were investigated with neutron reflectometry and a swelling by a factor of 3–5 was found in the presence of aqueous NaCl and MgCl 2 solutions compared to the dry state. During the data analysis, the applicability of a model-free evaluation was also demonstrated for the investigated polysulfobetaine brushes. Furthermore, it was found with GINSES that in contrast to neutral brushes, these polysulfobetaine brushes do not show the typical concentration fluctuations in the nanosecond time range when partially swollen with salt-free water.

36 MATERIALS SCIENCE↗