Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “blades”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Blade-vortex interaction noise predictions using measured blade surface pressures

The generation of helicopter noise by blade-vortex interactions during descent under impulsive conditions is investigated analytically. A noise-prediction technique is developed on the basis of the dipole source term of the Ffowcs-Williams/Hawkings equation and applied to data from simultaneous blade-pressure and acoustic measurements obtained by Cowan et al. (1986) on a 10-ft-diameter 4-blade rotor model in a wind tunnel. Preliminary results show that input-blade-airload azimuth resolution of 1 deg or better and computational azimuth step size of 2 deg or less are required to achieve good agreement between predicted and recorded acoustic time histories. The need for more sophisticated methods to model chordwise input data and for a more extensive experimental data base is indicated.

Ziegenbein, Perry R.↗
NASA NTRS1959

A Dynamic Model Investigation of the Effect of a Sharp-Edge Vertical Gust on Blade Periodic Flapping Angles and Bending Moments of a Two-Blade Rotor

A two-blade rotor having a diameter of 4 feet and a solidity of 0.037 was subjected to sharp-edge vertical gusts while being operated at various forward speeds to study the effect of the gusts on the blade periodic bending moments and flapping angles. Variables studied included gust velocity, collective pitch angle, flapping hinge offset, and tip-speed ratio. Dimensionless coefficients are derived for the periodic components of the incremental changes in blade flapping angles and bending moments which arise when a rotor blade penetrates a sharp-edge gust. Mental changes in both the flapping angles and bending moments are essentially proportional to gust velocity, and the coefficients express the ratio of these increments to gust velccity. The results show that the flapping coefficient usually increases with an increase in collective pitch angle, is generally dependent on tip-speed ratio, and is essentially independent of the amount of flapping hinge offset. The bending-moment coefficient is also dependent on collective pitch angle and tip-speed ratio. Expected reductions in bending moments are realized by the use of flapping hinges, and further reductions in bending moments are achieved as the amount of flapping hinge offset is increased. Comparison of the experimental results of this investigation with limited available theoretical results shows substantial agreement but indicates that the assumption that the response of the rotor to a sharp-edge gust is independent of the collective pitch angle prior to gust entry is probably inadequate.

McCarty, John Locke↗
NASA NTRS1985

Effects of Blade to Blade Dissimilarities on Rotor Body Lead Lag Dynamics

Small blade-to-blade property differences are investigated to determine how they affect the behavior of a simple rotor-body system. An analytical approach is used which emphasizes the significance of these effects from the experimental point of view. It is found that the primary effect of blade-to-blade dissimilarities is the appearance of additional peaks in the frequency spectrum which are separated from the conventional response peaks by multiples of the rotor speed. These additional responses are potential experimental problems because when they occur near a mode of interest they act as contaminant frequencies which can make damping measurements difficult. Increased rotor-body coupling and a rotor shaft degree of freedom act to improve the situation by altering the frequency separation of the modes.

McNulty, Michael J.↗
NASA NTRS1946

Altitude-Wind-Tunnel Investigation of Performance of Several Propellers on YP-47M Airplane at High Blade Loading: Curtiss 838-1C2-18R1 Four-Blade Propeller - 2

An investigation was conducted in the Cleveland altitude wind tunnel to determine the performance of a Curtiss propeller with four 838-lC2-lSRl blades on a YP-47M airplane at high blade loadings and engine powers. The study was made for a range of power coefficients between 0.30 and 1.00 at free-stream Mach numbers of 0.40 and 0.50. The results of the force measurements indicate primarily the trend of propeller efficiency for changes in power coefficient or advance-diameter ratio, inasmuch as corrections for the effects of tunnel-wall constriction on the installation have not been applied. Slip-stream pressure surveys across the propeller disk are presented to illustrate blade thrust load distribution for several operating conditions. At a free-stream Mach number of 0.40, nearly constant peak efficiencies were obtained at power coefficients from 0.30 to 0.70. A change in power coefficient from 0.70 to 0.90 reduced the peak efficiency about 5 percent. Blade stall at the tip sections became evident for a power coefficient of 0.91 when the advance-diameter ratio was reduced to 1.87. At a free-stream Mach number of 0.50, the highest propeller efficiencies were obtained for power coefficients from 0.80 to 1.00 at advance-diameter ratios above 2.90. At advance-diameter ratios below 2.90, the highest efficiencies were obtained for power coefficients of 0.60 and 0.70. The envelope of the efficiency curves decreased about 12 percent between advance-diameter ratios of 2.60 and 4.20. Local compressibility effects became evident for a power coefficient of 0.40 when the advance-diameter ratio was decreased to 1.75.

Wallner, Lewis E.↗
NASA NTRS2000

Turbine Blade and Endwall Heat Transfer Measured in NASA Glenn's Transonic Turbine Blade Cascade

Higher operating temperatures increase the efficiency of aircraft gas turbine engines, but can also degrade internal components. High-pressure turbine blades just downstream of the combustor are particularly susceptible to overheating. Computational fluid dynamics (CFD) computer programs can predict the flow around the blades so that potential hot spots can be identified and appropriate cooling schemes can be designed. Various blade and cooling schemes can be examined computationally before any hardware is built, thus saving time and effort. Often though, the accuracy of these programs has been found to be inadequate for predicting heat transfer. Code and model developers need highly detailed aerodynamic and heat transfer data to validate and improve their analyses. The Transonic Turbine Blade Cascade was built at the NASA Glenn Research Center at Lewis Field to help satisfy the need for this type of data.

Giel, Paul W.↗
NASA NTRS1940

Observations in Flight of the Region of Stalled Flow Over the Blades of the Kellett YG-1B Tapered-Blade Autogiro Rotor

In conjunction with a series of tests requested by the Army Air corps on a new set of tapered rotor blades, of NACA 230 series section and built for the Kellett YG-1B autogiro, it was convenient to supplement previous studies of the region or stalled flow on rotors by making photographic observations of the flow over the blades in flight. These observations are described in this report. It is shown that the maximum radius stalled on the new rotor increases more rapidly with tip-speed ratio than was true on the rectangular-blade, Gottingen 606 section rotor previously tested on the same ship, though the increase in importance of the stalled region is not as decisive as consideration of the change in section would suggest. The increased loss in the stalled region is felt to be at least a contributing cause in the failure of the new blades to Increase the top speed of the machine.

Gustafson, Frederic B.↗
NASA NTRS2019

Estimating Inducer Blade Damping in Water with On-Blade Strain Measurements

This paper describes the testing, methodology, and results for estimating critical damping ratios of inducer blade structural natural frequencies. A sub-scale inducer water flow test was performed with on-blade strain gauge measurements. Data were acquired in quiescent air and water, and also at several shaft speeds and operating conditions. Two methods were used to provide active excitation to the blades. The first was to impart a mechanical impulse to the inducer shaft and observe the strain gauge response. The second was to install a stator plate upstream of the inducer to create a non-uniform but regular pressure field at the inducer inlet. There are challenges with using either approach, but damping information was extracted using both methods. Results showed that the critical damping ratio for a given blade mode increased from air to quiescent water, and also increased when the inducer was spinning.

Mulder, Andrew↗
NASA NTRS1971

Concepts for a theoretical and experimental study of lifting rotor random loads and vibrations. Phase 5A: Effects of torsional blade flexibility on single blade random gust response statistics

Quasi-steady aerodynamics were assumed, as well as a torsion mode where the amplitude is proportional to the distance from the rotor center. Aerodynamic torsional moment inputs are limited to the region of reverse flow where the aerodynamic center and the section center of gravity are separated by half the blade chord. Thus negligible effects of blade torsional flexibility are obtained for rotor conditions with negligible reverse flow effects. Numerical examples refer to conditions with 1.6 rotor advance ratio. It was found that the random flapping response is only moderately affected by torsional flexibility. However large random torsional loads and deflections occur even if flapping is completely suppressed. The coupling of the actual flapping motion into the blade torsional motion produces a substantial increase in the random torsional loads or deflections.

Hohenemser, K. H.↗
NASA NTRS1972

Theory/test correlation of helicopter rotor blade element airloads in the blade stall regime

The effects of stall on a rotor blade element in a three-dimensional rotating environment was investigated. The model rotor test provided blade element airloads and local boundary layer flow characteristics at the three-quarter blade radius position for a wide range of rotor operating conditions. A description of the test program and the test results are presented.

Bobo, C. J.↗
NASA NTRS1974

Investigation of rotor blade element airloads for a teetering rotor in the blade stall regime

A model of a teetering rotor was tested in a low speed wind tunnel. Blade element airloads measured on an articulated model rotor were compared with the teetering rotor and showed that the teetering rotor is subjected to less extensive flow separation. Retreating blade stall was studied. Results show that stall, under the influence of unsteady aerodynamic effects, consists of four separate stall events, each associated with a vortex shed from the leading edge and sweeping over the upper surface of the rotor blade. Current rotor performance prediction methodology was evaluated through computer simulation.

Dadone, L. U.↗
NASA NTRS1979

Axial-flow compressor turning angle and loss by inviscid-viscous interaction blade-to-blade computation

A method for computation of the flow field around an arbitrary airfoil cascade on an axially symmetric blade-to-blade surface was developed which takes into account the development and separation of the blade surface boundary layers and mixing in the wake. The method predicts the overall fluid turning and total pressure loss in the context of an inviscid-viscous interaction scheme. The inviscid flow solution is obtained from a compressible flow matrix method. The viscous flow is obtained from a differential boundary layer method which calculates laminar, transitional and turbulent boundary layers. Provisions for the calculation of laminar and turbulent separation regions were added to the viscous scheme. The combined inviscid-viscous interaction scheme described yields results which are quantitatively consistent with experimental data. This suggests that the physical basis for the interactive system is correct and justifies continued exploration and use of the method.

Hansen, E. C.↗
NASA NTRS1979

Structural analysis of hollow blades: Torsional stress analysis of hollow fan blades for aircraft jet engines

A torsional stress analysis of hollow fans blades by the finite element method is presented. The fans are considered to be double circular arc blades, hollowed 30 percent, and twisted by a component of the centrifugal force by the rated revolution. The effects of blade hollowing on strength and rigidity are discussed. The effects of reinforcing webs, placed in the hollowed section in varying numbers and locations, on torsional rigidity and the convergence of stresses, are reported. A forecast of the 30 percent hollowing against torsional loadings is discussed.

Ogawa, A.↗
NASA NTRS1983

Space Shuttle main engine powerhead structural modeling, stress and fatigue life analysis. Volume 3: Stress summay of blades and nozzles at FPL and 115 percent RPL loads. SSME HPFTP and HPOTP blades and nozzles

Gasdynamic environments applied to the turbine blades and nozzles of the HPFTP and HPOTP were analyzed. Centrifugal loads were applied to blades to account for the pump rotation of FPL and 115 percent RPL. The computer models used in the blade analysis with results presented in the form of temperature and stress contour plots are described. Similar information is given for the nozzles.

Hammett, J. C.↗
NASA NTRS1984

Inlet boundary layer effects in an axial compressor rotor. I - Blade-to-blade effects

This paper discusses experimental data measured on the blading and downstream of an isolated compressor rotor with thick inlet endwall boundary layers. The objective of the study was to compare these results with data acquired previously with thin inlet boundary layers and to assess the impact of inlet boundary layer thickness on the secondary flow. Flow visualization results showed the powerful impact of the hub corner stall and how at the same near stall flow coefficient where with thin inlet boundary layers the blade was separated at midspan, with thick inlet boundary layers it was attached. It was also shown that while secondary flow was very weak, it did produce sufficient radial redistribution to cause an apparent negative loss at the blade root.

Wagner, J. H.↗
NASA NTRS1987

The measurement and control of helicopter blade modal response using blade-mounted accelerometers

The measurement of helicopter blade flapping, bending, and lag modal acceleration and displacement response using blade-mounted accelerometers is described. It is shown that knowledge of the blade mode shapes is sufficient to permit separation of the modal contributions to the accelerometer signals using matrix inversion. The application of the Mckillip (1985) filter to the identification of modal rate response is described. Finally, the design of flapping, bending, and lag mode controllers utilizing the conventional mesh plate is presented. The measurement technique is illustrated using flight test results obtained using a Black Hawk helicopter.

Ham, Norman D.↗
NASA NTRS1987

Estimation of blade airloads from rotor blade bending moments

This paper presents a method for the estimation of blade airloads, based on the measurements of flap bending moments. In this procedure, the blade rotation in vacuum modes is calculated, and the airloads are expressed as an algebraic sum of the mode shapes, modal amplitudes, mass distribution, and frequency properties. The method was validated by comparing the calculated airload distribution with the original wind tunnel measurements which were made using ten modes and twenty measurement stations. Good agreement between the predicted and the measured airloads was found up to 0.90 R, but the agreement degraded towards the blade tip. The method is shown to be quite robust to the type of experimental problems that could be expected to occur in the testing of full-scale and model-scale rotors.

Bousman, William G.↗