SEARCH · Engineering Papers
Results for “bandgap”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Giant visible and infrared light attenuation effect in nanostructured narrow-bandgap glasses
Not Available
Densely Aligned Graphene Nanoribbon Arrays and Bandgap Engineering
Graphene has attracted great interest for future electronics due to its high mobility and high thermal conductivity. However, a two-dimensional graphene sheet behaves like a metal, lacking a bandgap needed for the key devices components such as field effect transistors (FETs) in digital electronics. It has been shown that, partly due to quantum confinement, graphene nanoribbons (GNRs) with ~2 nm width can open up sufficient bandgaps and evolve into semiconductors to exhibit high on/off ratios useful for FETs. However, a challenging problem has been that, such ultra-narrow GNRs (~2 nm) are difficult to fabricate, especially for GNRs with smooth edges throughout the ribbon length. Despite high on/off ratios, these GNRs show very low mobility and low on-state conductance due to dominant scattering effects by imperfections and disorders at the edges. Wider GNRs (>5 nm) show higher mobility, higher conductance but smaller bandgaps and low on/off ratios undesirable for FET applications. It is highly desirable to open up bandgaps in graphene or increase the bandgaps in wide GNRs to afford graphene based semiconductors for high performance (high on-state current and high on/off ratio) electronics. Large scale ordering and dense packing of such GNRs in parallel are also needed for device integration but have also been challenging thus far. It has been shown theoretically that uniaxial strains can be applied to a GNR to engineer its bandgap. The underlying physics is that under uniaxial strain, the Dirac point moves due to stretched C-C bonds, leading to an increase in the bandgap of armchair GNRs by up to 50% of its original bandgap (i.e. bandgap at zero strain). For zigzag GNRs, due to the existence of the edge states, changes of bandgap are smaller under uniaxial strain and can be increased by ~30%. This work proposes a novel approach to the fabrication of densely aligned graphene nanoribbons with highly smooth edges afforded by anisotropic etching and uniaxial strain for bandgap engineering of GNRs towards high on/off ratio and high on-state current GNR devices. First, we will develop a novel approach for the fabrication of high density GNR arrays (pitch <50 nm, tunable down to 30nm) with pre-defined edge orientation and smooth edges using a free standing nano-mask derived from diblock copolymer assembly for patterning of graphene sheets. Anisotropic graphene edges will be developed to afford smooth edges along crystallographic lattice directions. Then, we will fabricate GNR devices on flexible substrates and apply uniaxial strain to engineer the bandgap of the GNRs. The bandgap of GNRs could be increased by up to 50% under uniaxial strain according to theoretical calculations and will be investigated through electrical transport measurements. Micro-Raman spectroscopy of single GNRs and parallel arrays will be used to probe and quantify the uniaxial strain. Electrical measurements will be used to probe the on/off ratio of GNR FET devices and confirm the bandgap tuning effects. Finally, we plan to use dense parallel arrays of GNRs to demonstrate strained GNR field effect transistors with high on/off ratios and high on-state current, and compare strained GNR FETs with carbon nanotube and Si based field effect transistor (FET) devices.
Ultrasensitive tunability of the direct bandgap of 2D [Twp-dimensional] InSe flakes via strain engineering
InSe, a member of the layered materials family, is a superior electronic and optical material which retains a direct bandgap feature from the bulk to atomically thin few-layers and high electronic mobility down to a single layer limit. We, for the first time, exploit strain to drastically modify the bandgap of two-dimensional (2D) InSe nanoflakes. We demonstrated that we could decrease the bandgap of a few-layer InSe flake by 160 meV through applying an in-plane uniaxial tensile strain to 1.06% and increase the bandgap by 79 meV through applying an in-plane uniaxial compressive strain to 0.62%, as evidenced by photoluminescence (PL) spectroscopy. The large reversible bandgap change of ~239 meV arises from a large bandgap change rate (bandgap strain coefficient) of few-layer InSe in response to strain, ~154 meV/% for uniaxial tensile strain and ~140 meV/% for uniaxial compressive strain, representing the most pronounced uniaxial strain-induced bandgap strain coefficient experimentally reported in 2D materials. We developed a theoretical understanding of the strain-induced bandgap change through first-principles DFT and GW calculations. We also confirmed the bandgap change by photoconductivity measurements using excitation light with different photon energies. In conclusion, the highly tunable bandgap of InSe in the infrared regime should enable a wide range of applications, including electro-mechanical, piezoelectric and optoelectronic devices.
The role of hydrothermal conditions in determining 1D TiO2 nanomaterials bandgap energies and crystal phases
Highlights: • Application of hydrothermal method for 1D TiO2 synthesis. • Varying hydrothermal synthesis conditions on 1D TiO2 crystal phase, size and SSA. • Effects on crystal phase, size and SSA on bandgap. - Abstract: One-dimensional TiO{sub 2} nanostructure synthesized using a hydrothermal method showed significant differences in the bandgap energies and crystal phase properties under different synthesis conditions. The objectives of this study were to evaluate the effect of the hydrothermal reaction conditions on the bandgap energy and to optimize the reaction conditions using a 3-factor 3-level Box Behnken design. The factors investigated include temperature, NaOH concentration and TiO{sub 2} concentration (BBD). A quadratic response surface model predicted optimum conditions for the maximum and minimum bandgap energy. The BBD analysis and other statistical tools provided evidence showing the temperature and NaOH concentration significantly affected the 1D TiO{sub 2} bandgap energy. Pure anatase was associated with a higher bandgap energy, whereas the biphasic anatase-rutile and anatase-TiO{sub 2}-B phases were linked with decreasing the bandgap energy. In addition, the crystal size and specific surface area (SSA) impact on the bandgap energy was due to the size quantization effect.
The Role of Dimethylammonium in Bandgap Modulation for Stable Halide Perovskites
Halide perovskites with bandgaps of 1.70–1.85 eV are of interest for multijunction photovoltaics. Mixing halides on the X site of the ABX3-structured perovskite system is a common way to reach these bandgaps, but this method introduces phase segregation pathways, limiting photovoltage. Recently, a new strategy for increasing the bandgap has been introduced, where cations normally too large to fit into the lattice, but compensated by smaller cations, are substituted on the A site. The mechanism underlying the increase of the bandgap with this strategy remained an open question. Here, we show that by partial substitution of the large dimethylammonium (DMA) cation at the A site of FA x Cs 1–x PbI y Br 3–y perovskites, a bandgap increase is observed not only when DMA is compensated by smaller Cs cations but also when only DMA is added, which is accompanied by an expansion of the crystal lattice. Our experimental findings suggest that adding DMA is causing an unexpected tilt in the perovskite octahedra, increasing the bandgap. Efficient solar cells based on 1.73 eV DMA-incorporated materials are extremely stable, retaining 96% of their original efficiency over 2200 h at 85 °C in the dark and 92% of their original efficiency after operation at 60 °C for 500 h. Finally, this octahedral tilting strategy is a promising route for attaining efficient and stable wide bandgap perovskite solar cells.
Luminescence in Conjugated Molecular Materials under Sub-bandgap Excitation
Light emission in semiconductors occurs when they are under optical and electrical excitation with energy larger than the bandgap energy. In some low-dimensional semiconductor heterostructure systems, this thermodynamic limit can be violated due to radiative Auger recombination (AR), a process in which the sub-bandgap energy released from a recombined electron-hole pair is transferred to a third particle leading to radiative band-to-band recombination.1 Thus far, photoluminescence up-conversion phenomenon has been observed in some low dimensional semiconductor systems, and the effect is very weak and it can only be observed at low temperatures. Recently, we discovered that efficient electroluminescence in poly[2-methoxy-5-(2’-ethylhexyloxy)-1, phenylenevinylene] (MEH-PPV) polymer light-emitting devices (PLEDs) at drive voltages below its bandgap voltage could be observed when a ZnO nanoparticles (NPs) electron injection layer was inserted between the polymer and the aluminum electrode. Specifically, emitted photons with energy of 2.13 eV can be detected at operating voltages as low as 1.2 V at room temperature. Based on these data, we propose that the sub-bandgap turn-on in the MEH-PPV device is due to an Auger-assisted energy up-conversion process. The significance of this discovery is three-fold. First, radiative recombination occurs at operating voltages below the thermodynamic bandgap voltage. This process can significantly reduce the device operating voltage. For example, the current density of the device with the ZnO NC layer is almost two orders of magnitude higher than that of the device without the NC layer. Second, a reactive metal is no longer needed for the cathode. Third, this electroluminescence up-conversion process can be applied to inorganic semiconductors systems as well and their operation voltages of inorganic LEDs can be reduced to about half of the bandgap energy. Based on our initial data, we propose that the sub-bandgap turn-on in MEH-PPV devices is due to Auger-assisted energy up-conversion process. Specifically, we propose that the up-conversion process is due to charge accumulation at the polymer/NPs interface. This model requires that holes should be the dominant carriers in the polymer and the polymer/ZnO NCs heterojunction should be a type II alignment. In order to determine the mechanism of the up-conversion process, we will characterize devices fabricated using polymers with different carrier transporting properties to determine whether hole accumulation at the polymer/nanocrystals is required. Likewise, we will also use NPs with different electronic structures to fabricate devices to determine how electron accumulation affects the up-conversion process. Finally, we will measure quantitatively the interface charge accumulation by electroabsorption and correlate the results with the up-conversion photoluminescence efficiency measurements under an applied electric field.
Photophysical Properties and Phase Behavior of Ultrawide Photovoltaic Bandgap Cesium–Lead-Based Triple Halide Perovskites
Metal halide perovskite films in the top cell of triple-junction tandems require bandgaps around 2.0 eV to achieve current matching, assuming that the middle absorbing layer is the commonly used FAPbI 3 composition and the bottom cell has a bandgap around 1.1 eV. Unfortunately, mixed organic/inorganic metal halide perovskites that have the necessary Br content to reach a bandgap of 2.0 eV segregate into iodine-rich and bromine-rich phases under illumination, limiting their obtainable voltage. Previous reports have shown improved photostability using either Cs-based inorganic compositions or Cl incorporation on the X-site. Here, we investigate the inorganic triple halide compositional space CsPb(I 1–x–y Br y Cl x ) 3 where bandgaps near 2.0 eV are expected based on the knowledge that CsPbI2Br has a bandgap of 1.90 eV. Incorporation of Cl occurs readily for x ≤ 0.07–0.10 within perovskites with a Br content of 0.3 ≤ y ≤ 0.42. When x >0.1, X-ray diffraction and photoluminescence (PL) measurements indicate that multiple compositional phases form. We hypothesize that the variable sizes of the three halide ions are not supported within the rigid Cs lattice, resulting in the formation of multiple compositional phases. The photoluminescence quantum yield of the single-phase compositional space–CsPb(I 1–x–y Br y Cl x ) 3 where x ≤ 0.07was typically 0.001–0.004%, most likely as a result of a high defect density, including mobile iodine species. PL light-soaking measurements of many perovskite compositions with bandgaps in the range of 1.89–2.05 eV demonstrate that phase segregation occurs when initial bandgaps are above 1.95 eV regardless of halide content: indicating further iodide oxidation and corresponding migration under illumination. The conclusion is that further compositional or additive engineering is necessary for the development of inorganic triple halide compositions that accomplish the elusive goal of fabricating high-quality and photostable 2.0 eV films for use in multijunction tandems.
Combining Organic Cations of Different Sizes Grants Improved Control over Perovskitoid Dimensionality and Bandgap
Because mixed-halide wide-bandgap (1.6-2.0 eV) perovskite solar cells suffer from operating instability related to light-induced halide segregation, it is of interest to study alternative means of bandgap widening. Perovskitoids combine wide bandgaps and structural stability resulting from face- or edge-sharing octahedral connections in their crystal structures. Unfortunately, there existed no prior reports of three-dimensional (3D) perovskitoids having direct bandgaps with optical absorption edges less than 2.2 eV. As the most significant predictor of perovskitoid bandgaps is the fraction of corner-sharing in their crystal structures, we hypothesized that increasing the amount of corner-sharing would access lower bandgaps than previously reported. Here, we accomplished this by mixing a spacer cation within the size range for 3D perovskitoid formation with a smaller perovskite-forming cation. We explored three spacer cations of different sizes: ethylammonium (EA), cyclopropylammonium (c-C3A), and cyclobutylammonium (c-C4A), combining these with methylammonium (MA), and found that the middle cation, c-C3A, pairs with MA to form a 3D perovskitoid with the formula (c-C3A) 3 (MA) 3 Pb 5 I 16 and a direct bandgap with an optical absorption edge at 2.0 eV. Solution-processed films of this perovskitoid showed improved light stability over mixed-halide perovskites, and solar cells based on these films exhibit increased maximum power point operating stability compared to reference mixed-halide devices.
Dipolar cations confer defect tolerance in wide-bandgap metal halide perovskites
Efficient wide-bandgap perovskite solar cells (PSCs) enable high-efficiency tandem photovoltaics when combined with crystalline silicon and other low-bandgap absorbers. However, wide-bandgap PSCs today exhibit performance far inferior to that of sub-1.6-eV bandgap PSCs due to their tendency to form a high density of deep traps. Here, we show that healing the deep traps in wide-bandgap perovskites—in effect, increasing the defect tolerance via cation engineering—enables further performance improvements in PSCs. We achieve a stabilized power conversion efficiency of 20.7% for 1.65-eV bandgap PSCs by incorporating dipolar cations, with a high open-circuit voltage of 1.22 V and a fill factor exceeding 80%. We also obtain a stabilized efficiency of 19.1% for 1.74-eV bandgap PSCs with a high open-circuit voltage of 1.25 V. From density functional theory calculations, we find that the presence and reorientation of the dipolar cation in mixed cation–halide perovskites heals the defects that introduce deep trap states.
Physical properties and analytical models of band-to-band tunneling in low-bandgap semiconductors
Low-bandgap semiconductors, such as InAs and InSb, are widely considered to be ideal for use in tunnel field-effect transistors to ensure sufficient on-current boosting at low voltages. This work elucidates the physical and mathematical considerations of applying conventional band-to-band tunneling models in low-bandgap semiconductors, and presents a new analytical alternative for practical use. The high-bandgap tunneling generates most at maximum field region with shortest tunnel path, whereas the low-bandgap generations occur dispersedly because of narrow tunnel barrier. The local electrical field associated with tunneling-electron numbers dominates in low-bandgap materials. This work proposes decoupled electric-field terms in the pre-exponential factor and exponential function of generation-rate expressions. Without fitting, the analytical results and approximated forms exhibit great agreements with the sophisticated forms both in high- and low-bandgap semiconductors. Neither nonlocal nor local field is appropriate to be used in numerical simulations for predicting the tunneling generations in a variety of low- and high-bandgap semiconductors.
A machine learning approach for determining temperature-dependent bandgap of metal oxides utilizing Allen–Heine–Cardona theory and O’Donnell model parameterization
To evaluate the high temperature sensing properties of metal oxide and perovskite materials suitable for use in combustion environments, it is necessary to understand the temperature dependence of their bandgaps. Although such temperature-driven changes can be calculated via the Allen–Heine–Cardona (AHC) theory, which assesses electron–phonon coupling for the bandgap correction at given temperatures, this approach is computationally demanding. Another approach to predict bandgap temperature-dependence is the O’Donnell model, which uses analytical expressions with multiple fitting parameters that require bandgap information at 0 K. This work employs data-driven Gaussian process regression (GPR) to predict the parameters employed in the O’Donnell model from a set of physical features. We use a sample of 54 metal oxides for which density functional theory has been performed to calculate the bandgap at 0 K, and the AHC calculations have been carried out to determine the shift in the bandgap at non-zero temperatures. As the AHC calculations are impractical for high-throughput screening of materials, the developed GPR model attempts to alleviate this issue by predicting the O'Donnell parameters purely from physical features. To mitigate the reliability issues arising from the very small size of the dataset, we apply a Bayesian technique to improve the generalizability of the data-driven models as well as quantify the uncertainty associated with the predictions. The method captures well the overall trend of the O’Donnell parameters with respect to a reduced feature set obtained by transforming the available physical features. Quantifying the associated uncertainty helps us understand the reliability of the predictions of the O’Donnell parameters and, therefore, the bandgap as a function of temperature for any novel material.
Development of high-bandgap AlGaInP solar cells grown by organometallic vapor-phase epitaxy
AlGaInP solar cells with bandgaps between 1.9 and 2.2 eV are investigated for use in next-generation multijunction photovoltaic devices. This quaternary alloy is of great importance to the development of III-V solar cells with five or more junctions and for cells optimized for operation at elevated temperatures because of the high bandgaps required in these designs. In this work, we explore the conditions for the organometallic vapor-phase epitaxy growth of AlGaInP and study their effects on cell performance. Initial efforts focused on developing ~2.0-eV AlGaInP solar cells with a nominal aluminum composition of 12%. Under the direct spectrum at 1000 W/m 2 (AM1.5D), the best of these samples had an open-circuit voltage of 1.59 V, a bandgap-voltage offset of 440 mV, a fill factor of 88.0%, and an efficiency of 14.8%. We then varied the aluminum composition of the alloy from 0% to 24% and were able to tune the bandgap of the AlGaInP layers from ~1.9 to ~2.2 eV. Furthermore, while the samples with a higher aluminum composition exhibited a reduced quantum efficiency and increased bandgap-voltage offset, the bandgap-voltage offset remained at 500 mV or less, up to a bandgap of ~2.1 eV.
Achieving a high open-circuit voltage in inverted wide-bandgap perovskite solar cells with a graded perovskite homojunction
Wide-bandgap (~1.7-1.8 eV) perovskite solar cells have attracted substantial research interest in recent years due to their great potential to fabricate efficient tandem solar cells via combining with a lower bandgap (1.1-1.3 eV) absorber (e.g., Si, copper indium gallium diselenide, or low-bandgap perovskite). However, wide-bandgap perovskite solar cells usually suffer from large open circuit voltage (V oc ) deficits caused by small grain sizes and photoinduced phase segregation. Here, we demonstrate that in addition to large grain sizes and passivated grain boundaries, controlling interface properties is critical for achieving high V oc 's in the inverted wide-bandgap perovskite solar cells. We adopt guanidinium bromide solution to tune the effective doping and electronic properties of the surface layer of perovskite thin films, leading to the formation of a graded perovskite homojunction. The enhanced electric field at the perovskite homojunction is revealed by Kelvin probe force microscopy measurements. This advance enables an increase in the V oc of the inverted perovskite solar cells from an initial 1.12 V to 1.24 V. With the optimization of the device fabrication process, the champion inverted wide-bandgap cell delivers a power conversion efficiency of 18.19% and sustains more than 72% of its initial efficiency after continuous illumination for 70 h without encapsulation. Additionally, a semitransparent device with an indium tin oxide back contact retains more than 88% of its initial efficiency after 100 h maximum power point tracking.
GaAs Thermophotovoltaic Patterned Dielectric Back Contact Devices with Improved Sub-Bandgap Reflectance
We demonstrate GaAs thermophotovoltaic (TPV) devices with a patterned dielectric back contact (PDBC) architecture, featuring a dielectric spacer between the semiconductor and back metal contact over most of the back surface for high reflectance, and metal point contacts over a smaller area for electrical conduction. In the TPV application, high sub-bandgap reflectance is needed to reflect unused sub-bandgap photons to the thermal emitter to minimize energy losses in this portion of the thermal spectrum. We explore different PDBC fabrication processes with SU-8 and SiO2 dielectric spacer layers to maximize sub-bandgap reflectance while minimizing series resistance to increase TPV conversion efficiency. We successfully demonstrate GaAs SU-8 PDBC TPV devices with 2200 degrees C blackbody-weighted sub-bandgap reflectance of 94.9% and 96.5% with and without a front metal grid, respectively. This is 0.7% and 2.3% (absolute) higher than the mean sub-bandgap reflectance of 94.2% for GaAs baseline TPV devices with 100% Au back contact with front metal grid. Lower sub-bandgap reflectance in TPV devices with front grids indicates the front grid induces light scattering leading to additional parasitic absorption in the TPV device. We also show that for higher contact coverage fractions, the PDBC reflectance cannot in general be treated by a linear interpolation using simple 1D transfer matrix method modeling and should be treated instead as a diffraction grating by solving Maxwell's equations in 3D.
Cement sensors with acoustic bandgaps using carbon nanotubes
Cement is widely used in wellbores to stabilize the steel casing used in wellbore operations for oil and gas production, enhanced geothermal systems and carbon sequestration, and to limit fluid movement between sub-surface strata. Flaws such as microcracks in wellbore cement can lead to leakage along the wellbore compromising wellbore integrity. There is an increasing need for methods to monitor cement crack propagation in wellbore environments. In this study, we develop and report the first cementitious sensors capable of exhibiting high frequency acoustic bandgaps (ABGs) using carbon nanotubes (CNTs). Computational simulations of a sensor unit cell are used to design cement-multi walled carbon nanotubes (MWCNTs) sensors that show a wide bandgap. When the cement-MWCNTs sensors is embedded in cement specimens, bandgaps were measured experimentally under 300 kHz and under 600 kHz, consistent with the computationally predicted bandgaps in the range of 290–360 kHz, 410–460 kHz and 515–585 kHz. These bandgap features were absent in homogeneous cement specimens. X-ray tomographic reconstructions showed microscopic debonding at cement-MWCNTs sensor interface. Frequency response analysis of a three-dimensional computational model indicated a shift of frequency of minimum transmission due to the interface debonding, but no perturbation of bandgap response was observed. Here, the cement-MWCNTs sensors developed in this study show the potential of a packed CNT inclusion material in cementitious matrix to create ABGs in a cement matrix.
Measuring the Electronic Bandgap of Carbon Nanotube Networks in Non-Ideal p-n Diodes
The measurement of the electronic bandgap and exciton binding energy in quasi-one-dimensional materials such as carbon nanotubes is challenging due to many-body effects and strong electron–electron interactions. Unlike bulk semiconductors, where the electronic bandgap is well known, the optical resonance in low-dimensional semiconductors is dominated by excitons, making their electronic bandgap more difficult to measure. In this work, we measure the electronic bandgap of networks of polymer-wrapped semiconducting single-walled carbon nanotubes (s-SWCNTs) using non-ideal p-n diodes. We show that our s-SWCNT networks have a short minority carrier lifetime due to the presence of interface trap states, making the diodes non-ideal. We use the generation and recombination leakage currents from these non-ideal diodes to measure the electronic bandgap and excitonic levels of different polymer-wrapped s-SWCNTs with varying diameters: arc discharge (~1.55 nm), (7,5) (0.83 nm), and (6,5) (0.76 nm). Our values are consistent with theoretical predictions, providing insight into the fundamental properties of networks of s-SWCNTs. The techniques outlined here demonstrate a robust strategy that can be applied to measuring the electronic bandgaps and exciton binding energies of a broad variety of nanoscale and quantum-confined semiconductors, including the most modern nanoscale transistors that rely on nanowire geometries.
A General Strategy for Bandgap Engineering Via Anion‐Lattice Doping in High‐Entropy Oxides
Bandgap engineering is a critical tool for tailoring the electronic properties of functional materials, traditionally achieved by modifying the cation sublattice. Here, a generalizable strategy is introduced that leverages facile anion-lattice doping in high entropy materials to modulate the bandgap in high-entropy metal oxides (HEMOs). By incorporating nitrogen into a single-phase high-entropy metal oxide/nitride (HEMO:HEMN) solid solution, a substantial bandgap reduction is achieved from 3.55 eV (HEMO) to ≈2.46 eV (HEMO:HEMN), significantly enhancing electronic conductivity. Unlike conventional bandgap tuning approaches that rely on cation substitution or heterojunction formation, this method exploits anion-mediated entropy stabilization, enabling uniform bandgap narrowing across the entire solid solution. This anion-lattice engineering strategy is broadly applicable to high-entropy systems, providing a new pathway for designing energy materials with tailored electronic properties. The resulting HEMO:HEMN solid solution exhibits a tenfold increase in capacitance and capacity compared to HEMO in supercapacitor and lithium-ion battery tests, demonstrating the transformative potential of anion-driven bandgap modulation for next-generation energy storage and conversion technologies.