Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Zircaloy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effect of neutron beamline irradiation on hydrogen equilibrium vapor pressure over hydrided Zircaloy-4

Here, the effect of neutron irradiation on the hydrogen equilibrium vapor pressure over hydrided samples of nickel-plated Zircaloy-4 was evaluated at the Washington State University Research Reactor’s epithermal beamline facility. To enable this study, a measurement capability was designed and assembled to obtain low pressure (<0.1 Pa) measurements over the temperature range of interest (i.e., ~300° - 400°C). Measurement results were in good agreement with tends extrapolated from previous data obtained at higher temperatures as well as recent thermodynamic data. No irradiation enhancement of vapor pressure was observed under the incident flux of epithermal neutrons over this temperature range.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

The deformation and burst behavior of Zircaloy-4 cladding tubes with hydride rim features subject to internal pressure loads

This study is motivated by the desire to conduct a separate effects test replicating specific aspects of an in-pile pulse reactor test on high exposure light water reactor (LWR) fuel rods. The principal purpose of the tests was to determine whether temperature and or hydrogen concentration thresholds exist in assessing the vulnerability of a stress relieved zirconium alloy cladding tubes to low strain ruptures. A secondary objective was to determine whether observations of the cladding stress during deformation could aid in the understanding of the crack formation and propagation in cladding tubes with hydride rim features. Here, the study utilized artificially hydrided Zircaloy-4 cladding tubes and an isothermal, internal pressure test that was controlled with an in-situ strain measurement. The test results show a clear transition in failure vulnerability between room temperature and 150 °C. Below 150 °C, cladding tubes rupture at very low uniform plastic strain—even at relatively modest cladding hydrogen levels. At and above 150 °C, cladding tubes only rupture at low uniform plastic strain if the cladding hydrogen content is greater than 500 ppm and usually experience at least some modest amount of plastic deformation prior to rupture. Post-test metallographs from non-ruptured cladding tubes show numerous primary cracks forming in the hydride rim and arresting at the metal/hydride interface. This observation combined with the decrease in bulk yielding of hydrided cladding tubes when compared to fresh non-hydrided tubes leads to the conclusion that the fracture stress of the hydride rims is related to and bounded by the yield stress of the zirconium metal. Some evidence is presented for a change in crack propagation mechanism from one of void formation on hydride plates and linkage at temperatures below 150 °C to more classical ductile shearing beneath the primary crack tip at temperatures above 150 °C. This apparent change in crack propagation mechanism may help explain the observed temperature and hydrogen concentration thresholds.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Temperature and time effects of post-weld heat treatments on tensile properties and microstructure of Zircaloy-4

Opportunities exist to expand the application of Zircaloy-4 (Zry-4) into lower-temperature (<100°C) applications. Welded areas within these structures are potential failure points and post-weld heat treatments (PWHTs) are not yet standardized for application in this temperature range. Zry-4 tungsten inert gas (TIG) welds were given PWHTs from 450-900°C with hold times from 0.5-48 hours to investigate changes to tensile properties and microstructure. Treatment of 800°C for 1 hour was found to produce the most ductile material, measured by total elongation of the tensile bar (16.5%). Furthermore, both PWHT time and temperature were observed to increase total elongation, except in extreme (>800°C or >18hours) cases, but the effect of temperature was stronger. The second order cumulative annealing parameter shows a trend with tensile properties. Average grain sizes in the fusion zone and heat affected zone did not change under any of the PWHTs until the development of an undesirable blocky-alpha phase, which was only observed to form in the heat affected zones for hold times greater than 18hr at 800°C.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Global and local texture development during initial plastic deformation of cold-pilgered Zircaloy-4 tubing

In this work we present a thorough characterization of the texture development during the initial step of a cold pilgering process of a Zircaloy-4 TREX tube, on which the axial cross section is reduced by 80% over a 40cm length with an overall Q-ratio of 2.34, followed by a recrystallization thermal treatment. Texture across a tapered specimen representing this working zone was characterized by neutron diffraction and high energy synchrotron x-ray diffraction at 28 positions (4 locations along its length and 7 locations across its thickness with 0.3 mm spatial resolution), and on the deformed end after the thermal treatment. Results show that the starting material (TREX tube) presents a texture gradient through its wall thickness, with the c poles aligned to the hoop direction at the outer surface (with radial and hoop Kearns factors: f R =0.36, f H = 0.50), and gradually rotating around the axial direction to become a quasi-radial orientation (~35 o out of the radial direction) at the inner surface ( f R =0.43, f H =0.35). The overall texture becomes more radial due to the cold pilgering, but the texture gradient remains during the whole deformation process, being always more radial at the inner surface, ( f R =0.53, f H =0.37 at 80%) than at the outer surface ( f R =0.41, f H =0.50at 80%). The most remarkable changes in texture produced by the rolling process is a 30 o rotation of the grains around their c-axis, producing a marked increase of the <11 2 ¯ 0> // axial fiber texture at expenses of the original <10 1 ¯ 0> // axial fiber texture observed in the TREX tube. The observed changes in texture during deformation were correctly explained by visco-plastic self-consistent (VPSC) modelling. This was achieved after the inclusion of the basal <a> slip system, which plays a central role to explain the 30 o rotation around the c-axis during deformation. The texture evolution was correctly described after the inclusion of a drag effect to grain rotation due to the interaction with neighbouring grains. The through thickness texture differences are greatly reduced by the recrystallization thermal treatment, with similar Kearns factors at the inner surface ( f R =0.50, f H =0.28) and the outer surface ( f R =0.48, f H =0.39). The predominance of the <10 1 ¯ 0> // axial fiber texture is recovered after recrystallization.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Determination of the hydrogen heat of transport in Zircaloy-4

During operation in a nuclear reactor, Zr-based nuclear fuel cladding is subject to waterside corrosion which can lead to hydrogen ingress. Here, the hydrogen that enters the material will migrate to colder spots and precipitate as zirconium hydrides if the hydrogen content exceeds the hydrogen terminal solid solubility in the material. Since a temperature gradient is established in the radial direction of the cladding during operation, the hydrides can preferentially precipitate at the colder outer surface of the cladding. Other gradients can also occur in the longitudinal and azimuthal directions of the cladding tube. As a consequence, hydrogen redistributes itself in response to the concentration and temperature gradients present in the sample. The response of the hydrogen in solid solution to temperature gradients is governed by the heat of transport Q* as a function of temperature, so it can be used in the BISON code. A set of experiments was set up to determine the heat of transport (Q*), in which a uniformly hydrided Zircaloy-4 sample is annealed under a fixed temperature gradient at a range of temperatures, and the resulting hydrogen distribution is analyzed to determine Q*. The results are discussed in terms of existing literature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

In-situ determination of strain during transient burst testing and the temperature dependence of Zircaloy-4 claddings

Understanding fuel system behavior during postulated loss-of-coolant accidents is pertinent for continued safe and efficient operation of light water reactors, particularly as higher burnups are being pursued and safety margins re-evaluated. Conventional mechanical models for the incumbent Zr alloys typically rely on the assumption that steady-state creep is the dominant fuel cladding response during transient accident conditions. To investigate this assumption, simulated accident burst testing was performed on Zircaloy-4 claddings with balloon behavior measured in-situ. Here, two distinct loading conditions were utilized during burst testing: (1) constant-gas-inventory where pressure was allowed to increase with temperature and (2) constant pressure. In-situ strains and strain rates were measured via 2-dimensional digital image correlation techniques and synchronized with temperature to determine deformation dependencies. The temperature dependence of strain rate was characterized by a two segment Arrhenius relationship, with a distinct transition between the high and low temperature/strain regimes. The average activation energy of the lower temperature/strain regime was 328 ± 25 kJ/mol, in agreement with the ~320 kJ/mol used for conventional LOCA models. However, the higher temperature/strain segment, which encompassed most of ballooning, showed increased activation energies as well as a dependence on whether the burst region was in view. For tests that burst away from the camera view, the average high temperature/strain segment activation energy was 635 ± 150 kJ/mol. For samples where the rupture opening formed in view, the average activation energy was 1015 ± 179 kJ/mol. This observed shift in temperature dependence indicates a transition in deformation mechanism at the end of life, possibly to time independent failure mechanisms, which has not yet been visualized in the literature for Zr alloys. Parameters at the transition points were analyzed to determine thresholds for this change in behavior, which occurred at an average hoop strain of 6.9 ± 2.1 %.

36 MATERIALS SCIENCE↗
DOE OSTI2024

In-situ strain behavior and BISON simulations of Zircaloy cladding subjected to temperature cycling separate-effects tests in a steam environment

Understanding fuel system performance during anticipated transients without scram (ATWSs) in boiling water reactors (BWRs) is necessary for refining current and future safety limits. High-fidelity material models and simulations are fundamental to rigorous assessment of zirconium-based cladding performance. However, experimental thermomechanical data during simulated ATWSs to validate these modes are limited. To provide relevant in-situ data, Zircaloy-4 cladding was subjected to cyclic heating in a steam environment to simulate an out-of-pile BWR ATWS. Digital image correlation was used to capture the cladding strain behavior in-situ for comparison against simulations using the BISON finite element code. Conventional high-temperature models were compared using multiple schemes to gain a better understanding of the applicability of three BISON models to BWR ATWS: (1) the default combination of creep models in BISON, (2) the high-temperature Erbacher model alone, and (3) the low-temperature Limback-Andersson model alone. The cases run with the Limback-Andersson model alone produced the lowest root mean square error (RMSE). The lowest RMSE for the Limback-Andersson model alone was 0.659%, and the highest RMSE reported was 4.22%. A data gap within the model in the temperature regime of interest was also identified, and to account for this gap, the current model in BISON is linearly interpolated between two separate datasets. In conclusion, this evaluation highlights the need to either develop a new model or to improve the existing model to capture transient creep effects resulting from a cyclic temperature transient.

Anticipated transient without SCRAM↗
DOE OSTI2021

ZrN Phase Formation, Hardening and Nitrogen Diffusion Kinetics in Plasma Nitrided Zircaloy-4

Plasma nitridation was conducted to modify the surfaces of Zircaloy-4. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Raman analysis were used to characterize microstructures and phases. Surface indentation and cross-sectional indentation were performed to evaluate mechanical property changes. Nitridation forms a thin layer of ZrN phase, followed by a much deeper layer affected by nitrogen diffusion. The ZrN phase is confirmed by both TEM and Raman characterization. The Raman peaks of ZrN phase show a temperature dependence. The intensity increases with increasing nitridation temperatures, reaches a maximum at 700 °C, and then decreases at higher temperatures. The ZrN layer appears as continuous small columnar grains. The surface polycrystalline ZrN phase is harder than the bulk by a factor of ~8, and the nitrogen diffusion layer is harder by a factor of ~2–5. The activation energy of nitrogen diffusion was measured to be 2.88 eV. The thickness of the nitrogen-hardened layer is controllable by changing the nitridation temperature and duration.

36 MATERIALS SCIENCE↗
DOE OSTI2023

SPC-70702 Rev 0 Zircaloy-4 Debris Shields for Use in MARVEL Build to Print Fabrication Specification

A. Idaho National Laboratory (INL) is developing a microreactor to produce electrical power utilizing a small nuclear core and Stirling engines under the Microreactor Application Research Validation and Evaluation (MARVEL) program. This procurement specification defines the requirements for fabrication of the Zircaloy-4 debris shields. B. Any conflict between this specification and referenced Codes and Standards, or any supplementary specifications in the procurement documents requires written clarification from the Contractor prior to proceeding with any work. Any deviation from the procurement documents requires approval by the Contractor with the change request process.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2024

Fuel performance analysis of Cr-coated Zircaloy-4 cladding during a prototypical LOCA event using BISON

Here, deformation and failure of chromium (Cr) coated Zircaloy-4 (Zry-4) were studied in loss-of-coolant accident (LOCA) conditions using the BISON fuel performance code. The BISON validation model simulating Halden research reactor experiments was extended to include Cr coatings and higher rod internal pressures to simulate high-burnup fuel. The transient simulations show Cr coatings help relieve stress in the Zry-4 substrate during the transient, delaying the onset of high-temperature creep, which leads to ballooning and bursting of the cladding. A nominal Cr coating thickness of 30 µm delays clad failure by 26 seconds and increases the clad burst temperature by 40 K. A parametric study showed that time to failure and burst temperature both increase with coating thickness, and Cr-coated cladding offers burst resistance under a wide range of rod internal pressures simulating high-burnup fuel. Results indicate that a thin Cr coating provides resistance against ballooning and bursting of cladding during LOCA events.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Measuring thermal diffusivity and gap conductance in uranium nitride and Zircaloy relevant for microreactor applications

Heat transfer across nuclear fuels and structural interfaces is an important factor for evaluating the performance of nuclear power systems. Specifically, heat generated as nuclear fuel fissions must be transported through the cladding material and through the reactor to reach the steam turbine for power generation. As new microreactor designs emerge, maximizing the efficiency of this heat transfer process becomes crucial to make them commercially viable. This article examines thermal diffusivity and gap conductance in uranium nitride (UN) fuel and Zircaloy-4 (Zry4) cladding using light flash analysis (LFA). Thermal diffusivity measurements were made on monolithic UN pellets and Zry4 exposed to carbon at peak operating temperatures of microreactors and show that carbon ingress has a minimal effect on thermal diffusivity when compared with identical materials not exposed to carbon. Evaluation of gap conductance at the UN-Zry4 interface was done using one-dimensional two-layer thermal transport models as a function of applied pressure. Here the results show that increasing pressure on the UN-Zry4 interface leads to gains in gap conductance per unit area in fuel-cladding assemblies at microreactor operating temperatures. While many other variables are expected to influence UN-Zry4 interfacial gap conductance (e.g. contact surface roughness, porosity, localized heating, environmental gas pressure), the work offers a demonstration of using a conventional LFA apparatus to determine this parameter at elevated temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Ion irradiation effects on Cr-coated zircaloy-4 surface wettability and pool boiling critical heat flux.

The concept of coating the currently used nuclear fuel cladding (zirconium-based alloy, typically Zircaloy-4 or Zirc-4) with an oxidation preventive layer is a progressing Accident tolerant Fuel (ATF) candidate alloys. The coated Zirc-4-based alloys could be a solution to suppress undesirable fast reaction kinetics with high-temperature steam. Zirc-4 has been the most preferred cladding material in pressurized water reactors (PWRs). Chromium (Cr) based alloys as a coating material provides excellent corrosion protection and good strength and wear resistance. In this paper, we present the surface wettability measurements and pool boiling Critical Heat Flux (CHF) for Cr-coated Zirc-4 claddings pre- and post-exposure to an ion irradiation environment. The wettability measurements, including static contact angle (contact angle, θ) and average surface roughness (surface roughness, Ra), are introduced for samples of different coating thicknesses (5–30 μm thick). The coatings fabricated by the cold spray of Cr-Al particles to 10 mm × 10 mm × 1.95 mm Zirc-4 substrates. Post fabrication, a Pilgering (cold rolling) process, was applied to finalize the coating thickness and resulted in a significant reduction in surface roughness of initially fabricated rough surfaces. The process produced three distinguished samples 5-μm unpolished (as machined), 5-μm, and 30-μm polished (cold rolled). The measurements are presented for the three surfaces and bare Zirc-4 as a baseline surface. The contact angle analyses were implemented in theoretical models from the literature to predict pool boiling CHF. Pool boiling experiments were conducted to measure the pool boiling CHF values and compare them to the predicted values. Scanning Electron Microscope (SEM) images and Energy Dispersive X-ray Spectroscopy (EDS) analysis was performed to characterize the surfaces for better understanding and interpreting the results. The SEM images showed localized surface damage due to ion irradiation. No recognized change in the measured surface roughness due to ion irradiation. The contact angles of irradiated Cr-coated surfaces are consistently higher (10°) than pre-irradiated surfaces. Decreasing the Cr-coating layer thickness resulted in lower contact angle pre- and post- ion irradiation. The predicted pool boiling CHF using the Kandlikar model is in good agreement with the experimentally measured CHF values within ±12% for all samples.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Model for determining rupture area in Zircaloy cladding under LOCA conditions

The dispersal of nuclear fuel through a cladding rupture opening during a transient event is the primary safety concern preventing the United States nuclear industry from extending burnup beyond a peak rod average burnup of 62 GWd/tU. The majority of research thus far has prioritized understanding, or at a minimum prioritized quantifying, fuel fragmentation and pulverization as a function of burnup and to a lesser extent onset temperature. Early high burnup loss-of-coolant accident tests performed at the Halden Boiling Water Reactor evaluated the impact of relocation on cladding temperature, whereas historical and recent cladding burst tests focused primarily on generating data related to cladding balloon and burst timing. However, very little effort has been put forth to develop a relationship for determining the rupture opening dimensions for Zircaloy cladding tubes bursting during a simulated light water reactor loss-of-coolant accident. This is significant because high burnup loss-of-coolant accident data suggest dispersal could be limited by the size of the rupture opening or rupture dimensions, thereby minimizing the safety concern. Therefore, the purpose of this research is to build a database composed of all simulated loss-of-coolant accident data to develop an empirical model that conservatively captures the rupture opening dimensions and translates those dimensions to rupture area. Analysis of the experimental data indicates the rupture dimensions are strongly correlated to the peak balloon strain. This relationship is leveraged to develop a rupture length empirical correlation as a function of peak balloon strain and a rupture width empirical correlation as a function of rupture length. Outliers in the experimental data are identified and discussed. Finally, the rupture opening empirical model is presented in such a way for general implementation into high fidelity fuel performance codes or fuel performance codes used for safety analyses.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

The influence of laser energy on deuterium emission characteristics from a Zircaloy-4 plasma

Laser-produced plasma coupled with optical emission spectroscopy (OES) is a promising technique for detecting certain isotopes, with unique capabilities such as standoff and rapid detection and minimal to no sample preparation requirements. The key figure-of-merit for isotopic analysis using optical spectroscopy tools is the linewidth relative to the isotope shift. Although the isotopes of hydrogen (1H, 2H, and 3H) possess large isotopic shifts (1H–2H ≈ 180 pm, 1H–3H ≈ 240 pm), being a light element, the H transitions are susceptible to various broadening mechanisms in the plasma environment. One of the critical parameters that influence the linewidth of a transition in an LPP is the incident laser energy. In the present study, we evaluated the role of laser energy on plume expansion dynamics, deuterium emission intensity, and linewidth in a nanosecond laser-produced Zircaloy-4 plasma. The changes in 2Hα emission intensity and linewidth were investigated for varying laser fluence and time after plasma onset. Spatially resolved and spatially integrated OES were performed and compared to investigate the emission spectral features and linewidth of 2Hα. Monochromatic two-dimensional time-resolved imaging was also performed to understand the morphology of the deuterium and protium emission relative to all species in the plume. Our results showed that 1Hα and 2Hα emissions predominantly occur closer to the target. Measurements of 2Hα linewidth approached similar values at later times of plasma evolution regardless of the laser energy. The linewidths of the 2Hα transition showed insignificant differences between spatially resolved and spatially integrated measurements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Thermomechanical Microstructural Predictions of Fracture Nucleation of Zircaloy-4 Alloys With δ and ε Hydride Distributions

Abstract A crystalline dislocation-density formulation that was incorporated with a nonlinear finite-element (FE) method was utilized to understand and to predict the thermomechanical behavior of an hexagonal closest packed (h.c.p.) zircaloy system with hydrides with either face-centered cubic (f.c.c.) or body-centered cubic (b.c.c.) hydrides. This formulation was then used with a recently developed fracture methodology that is adapted for finite inelastic strains and multiphase crystalline systems to understand how different microstructurally based fracture modes nucleate and propagate. The interrelated microstructural characteristics of the different crystalline hydride and matrix phases with the necessary orientation relationships (ORs) have been represented, such that a detailed physical understanding of fracture nucleation and propagation can be predicted for the simultaneous thermomechanical failure modes of hydride populations and the matrix. The effects of volume fraction, morphology, crystalline structure, and orientation and distribution of the hydrides on simultaneous and multiple fracture modes were investigated for radial, circumferential, and mixed distributions. Another key aspect was accounting for temperatures changes due to the effects of thermal conduction and dissipated plastic work and their collective effects on fracture. For hydrided aggregates subjected to high temperatures, thermal softening resulted in higher ductility due to increased dislocation-density activity, which led to higher shear strain accumulation and inhibited crack nucleation and growth. The predictions provide validated insights into why circumferential hydrides are more fracture-resistant than radial hydrides for different volume fractions and thermomechanical loading conditions.

Engineering↗
DOE OSTI2021

Microstructure Investigation and Mechanical Properties of Coated Zircaloy Cladding

Accident Tolerant Fuel concepts have been developed and tested in diverse research programs presently around the world. Industry teams have developed proprietary coating compositions and geometries, but significant knowledge gaps exist in terms of the resulting properties of the coating and the cladding and how those components impact each other in reactor conditions. Furthermore, the national laboratory and university teams currently studying the industry concepts are limited in their ability to freely disseminate and discuss results obtained on commercial coatings. The Advanced Fuels Campaign is therefore working to develop an understanding of ‘generic’ coatings applied to commercial nuclear cladding alloys free of these constraints. This milestone report provides insights in the microstructure of a 7-micrometer Cr coating on Zircaloy-2 and a 5- micrometer coating on Zry-4 as reference materials. SEM and TEM methods were utilized to describe and identify the interface, while nanoindentation was used to determine hardness and E-Moduli of coating and cladding material. This milestone summarizes the acquired knowledge to build a necessary verified foundation for future simulation and qualification efforts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Welded and Hydrogen Charged Zircaloy-4 and Welded Stainless Steel 347 Property Data and Microstructures for the Target Solution Vessel and Support Lines of SHINE

SHINE Medical Technologies is developing a facility that will produce molybdenum-99 for medical isotope procedures. As part of this facility, a metal tank, called the target solution vessel (TSV), will hold a uranyl sulfite solution. The TSV must withstand neutron irradiation near room temperature and potential corrosion from the aqueous solution. The large cylindrical TSV will be fabricated by welding and will have numerous pipes and connections also attached via welding. The vessel and those pipes will have varying thicknesses so both gas tungsten arc welding (GTAW) and flux-cored arc welding (FCAW) will be necessary to fabricate different sections. The original material under consideration for the TSV was Zircaloy-4 (Zry-4), but it is known to form a hydride which can degrade its mechanical properties. Thus, some investigation here is focused on the effects of hydrogen uptake in the Zry-4. Additionally, the alternative material being considered is AISI 347, a stainless steel. Both materials have little existing data for their neutron irradiation behavior below 100°C, and both have open questions on the weld behavior under neutron irradiation. Testing has focused on characterizing their weld properties with tensile tests and performing neutron irradiation of samples in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL).

07 ISOTOPE AND RADIATION SOURCES↗