Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WORK FUNCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Work function measurements of clean and modified carbon nanospikes

Carbon surfaces incorporating densely packed spikes with nanometer sharpness have shown exceptional electrocatalytic properties attributed to the enhanced electric field from the topography of the spikes. In this article, the composition of nanospike surfaces is identified by x-ray photoelectron spectroscopy (XPS) and their absolute work function determined using ultraviolet photoemission spectroscopy (UPS). Low temperature annealing of as-grown samples above 275 °C is required to produce a clean surface which has a 4.13 eV work function, a half volt lower than that of flat graphite. Treatments that contaminate the spiked surface, including exposure to air, oxidation at elevated temperature, or immersion in water or hydrocarbons, all increase the work function. Processing that blunts the spikes, including exposure to an oxygen plasma, argon sputtering, or high temperature annealing (800 °C) result in a work function close to that of flat graphite. An unusual double onset in the UPS secondary electron intensity is observed on as-grown nanospike samples and is reproduced by absorbing hydrocarbons on the surface. In conclusion, this double onset appears to be unique to carbon substrates and may originate in inelastic scattering of photoelectrons.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Tuning the work function of graphene by nitrogen plasma treatment with different radio-frequency powers

Graphene prepared by the chemical vapor deposition method was treated with nitrogen plasma under different radio-frequency (rf) power conditions in order to experimentally study the change in the work function. Control of the rf power could change the work function of graphene from 4.91 eV to 4.37 eV. It is shown that the increased rf power may lead to the increased number of graphitic nitrogen, increasing the electron concentration, and shifting the Fermi level to higher energy. The ability to controllably tune the work function of graphene is essential for optimizing the efficiency of optoelectronic and electronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Effects of Atomic Scale Roughness at Metal/insulator Interfaces on Metal Work Function

We evaluate the performance of different van der Waals (vdW) corrected density functional theory (DFT) methods in predicting the structure of perfect interfaces between the LiF(001), MgO(001), NiO(001) films on the Ag(001) surface and the resulting work function shift of Ag(001). The results demonstrate that including the van der Waals interaction is important for obtaining accurate interface structures and the metal work function shift. The work function shift results from a subtle interplay of several effects strongly affected by even small changes in the interface geometry. This makes the accuracy of theoretical methods insufficient for predicting the shift values better than within 0.2 eV. Most of the existing van der Waals corrected functionals are not particularly suited for studying metal/insulator interfaces. The lack of accurate experimental data on the interface geometries and surface rumpling of insulators hampers the calibration of existing and novel density functionals.

Environmental Molecular Sciences Laboratory↗
DOE OSTI2014

Understanding the bond-energy, hardness, and adhesive force from the phase diagram via the electron work function

Properties of metallic materials are intrinsically determined by their electron behavior. However, relevant theoretical treatment involving quantum mechanics is complicated and difficult to be applied in materials design. Electron work function (EWF) has been demonstrated to be a simple but fundamental parameter which well correlates properties of materials with their electron behavior and could thus be used to predict material properties from the aspect of electron activities in a relatively easy manner. In this article, we propose a method to extract the electron work functions of binary solid solutions or alloys from their phase diagrams and use this simple approach to predict their mechanical strength and surface properties, such as adhesion. Two alloys, Fe-Ni and Cu-Zn, are used as samples for the study. EWFs extracted from phase diagrams show same trends as experimentally observed ones, based on which hardness and surface adhesive force of the alloys are predicted. This new methodology provides an alternative approach to predict material properties based on the work function, which is extractable from the phase diagram. This work may also help maximize the power of phase diagram for materials design and development.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Measurements of the work function of single-walled carbon nanotubes encapsulated by AgI, AgCl, and CuBr using Kelvin probe technique with different kinds of probes

We report the results on the measurements of the work function of single-walled carbon nanotubes encapsulated by Agl (AgI@SWCNT), AgCl (AgCl@SWCNT), and CuBr (CuBr@SWCNT) by the local Kelvin probe technique. We found the values of the work function of tubes encapsulated with AgI and AgCl (Φ(AgI@SWCNT) = 5.08 ± 0.02, Φ(AgCl@SWCNT) = 5.10 ± 0.02 eV) to exceed substantially that of pristine carbon nanotubes, and the value of the work function of carbon nanotubes encapsulated with CuBr is Φ(CuBr@SWCNT) = 4.89 ± 0.03 (eV). The measurements are carried out using different kinds of microscope probes including multi-walled carbon nanotube tips.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2014

Generic trend of work functions in transition-metal carbides and nitrides

Transition-metal carbides and nitrides (TMCs and TMNs) are promising electrode materials for various electronic devices such as metal-oxide-semiconductor field-effect transistors and metal-insulator-metal capacitors. In this paper, the work functions of TMCs and TMNs are discussed systematically. Based upon the origin of the work function, the effect upon transition metal species by different periodic table groups is explained, carbides are compared with nitrides for the same transition metal, and the effect of carbon or nitrogen vacancies is discussed. In addition, a method to estimate the generic trend of the work function is proposed for TMC{sub x}, TMN{sub x}, TMC{sub 1−y}N{sub y} (transition metal carbonitrides), and TM{sub 1−z}TM′{sub z}C (alloy carbides)

36 MATERIALS SCIENCE↗
NASA NTRS1976

Work function determination of promising electrode materials for thermionic energy converters

The work function determinations of candidate materials for low temperature (1400 K) thermionics through vacuum emission tests are discussed. Two systems, a vacuum emission test vehicle and a thermionic emission microscope are used for emission measurements. Some nickel and cobalt based super alloys were preliminarily examined. High temperature physical properties and corrosion behavior of some super alloy candidates are presented. The corrosion behavior of sodium is of particular interest since topping cycles might use sodium heat transfer loops. A Marchuk tube was designed for plasma discharge studies with the carbide and possibly some super alloy samples. A series of metal carbides and other alloys were fabricated and tested in a special high temperature mass spectrometer. This information coupled with work function determinations was evaluated in an attempt to learn how electron bonding occurs in transition alloys.

Jacobson, D.↗
DOE OSTI2014

High tunability of the work function of (001) surface of ReO{sub 3} with O-vacancies: First principles analysis

Physical and chemical properties of transition metal oxides are central to the emerging field of oxide electronics. However, they are greatly influenced by defects, particularly, oxygen vacancies, which are always present in oxides. Here, we show how the control of oxygen vacancies at (001) surface of ReO{sub 3} can be used to tune its work function from 7 to 3 eV, based on first-principles density functional theoretical calculations of its structure, electronic and magnetic properties. The work function is shown to correlate directly with the stability of surface and exhibit a linear dependence on surface energy. We further assess the stability of ReO{sub 3} surface by determining its phonon dispersion, and explain how the surface stresses effectively strengthen structural instability leading to size dependence of its pressure dependent structural phase transitions observed experimentally. Our results highlight how significantly oxygen vacancies alter the work function of a metallic oxide and has important consequences to development of electronic devices and catalysts based on oxide heterostructures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1973

Determination of work functions near melting points of refractory metals by using a direct-current arc.

A direct-current arc in argon at atmospheric pressure was used to determine effective work functions of refractory metals, including tantalum, tungsten, molybdenum, and niobium. The procedure is experimentally advantageous, because surface cleanliness of the specimen is not critical, high vacuum is not required, and the anode-cathode spacing is not critical. The experimental procedure involves striking an arc to a metal wire cathode to form a melted ball having an emitting area defined by its diameter. The literature melting point of the metal is taken as the emitting temperature. By using these parameters and the known arc current, effective work functions were calculated from the Richardson-Dushman equation. The calculated work functions agree with recommended handbook values to within about 0.1 V and have typical repeatabilities of 0.02 V.

Gordon, W. A.↗
DOE OSTI2016

Work function of bulk-insulating topological insulator Bi{sub 2–x}Sb{sub x}Te{sub 3–y}Se{sub y}

Recent discovery of bulk insulating topological insulator (TI) Bi{sub 2–x}Sb{sub x}Te{sub 3–y}Se{sub y} paved a pathway toward practical device application of TIs. For realizing TI-based devices, it is necessary to contact TIs with a metal. Since the band-bending at the interface dominates the character of devices, knowledge of TIs' work function is of essential importance. We have determined the compositional dependence of the work function in Bi{sub 2–x}Sb{sub x}Te{sub 3–y}Se{sub y} by high-resolution photoemission spectroscopy. The obtained work-function values (4.95–5.20 eV) track the energy shift of the surface chemical potential seen by angle-resolved photoemission spectroscopy. The present result serves as a useful guide for developing TI-based electronic devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Effect of the sample work function on alkali metal dosing induced electronic structure change

Alkali metal dosing (AMD) has been widely used as a way to control doping without chemical substitution. This technique, in combination with angle resolved photoemission spectroscopy (ARPES), often provides an opportunity to observe unexpected phenomena. However, the amount of transferred charge and the corresponding change in the electronic structure vary significantly depending on the material. Here, we report study on the correlation between the sample work function and alkali metal induced electronic structure change for three iron-based superconductors: FeSe, Ba(Fe 0.94 Co 0.06 ) 2 As 2 and NaFeAs which share a similar Fermi surface topology. Electronic structure change upon monolayer of alkali metal dosing and the sample work function were measured by ARPES. In this work, our results show that the degree of electronic structure change is proportional to the difference between the work function of the sample and Mulliken's absolute electronegativity of the dosed alkali metal. This finding provides a possible way to estimate the AMD induced electronic structure change.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Transient work function gating: A new photoemission regime

We present the theoretical basis for a new photoemission regime, transient work function gating (TWFG), which temporally and energetically gates photoemission and produces near-threshold photoelectrons with thermally limited emittance, percent-level quantum efficiency, and control over temporal coherence. The technique consists of actively gating the work function of a generalized photocathode using a non-ionizing long-wavelength optical field to produce an adiabatic modulation of the carrier density at their surface. We examine TWFG as a means to circumvent the long-standing trade-off between low emittance and high quantum efficiency, untethered to particle source or photocathode specifics. TWFG promises new opportunities in photoemission physics for next generation electron and accelerator-based x-ray photon sources.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1971

Molybdenum work function determined by electron emission microscopy.

A polycrystalline molybdenum sample was recrystallized and thermally stabilized. Quantitative measurements of the emission from each individual grain were obtained with an electron emission microscope. The effective work function for each grain was then calculated. The crystallographic orientation of each grain was determined by Laue back-reflection techniques. A polar plot of effective work function vs crystallographic orientation for the sample was constructed to provide a correlation between effective work function and crystallographic orientation.

Jacobson, D. L.↗
DOE OSTI2015

In-situ investigation of graphene oxide under UV irradiation: Evolution of work function

Using in-situ Kelvin probe force microscopy (KPFM) to measure surface potential, we investigated the time-dependent work function evolution of solution-processed graphene oxide (GO) under ultraviolet (UV) irradiation. We found that the work function of GO exposed in UV shows a notable decrease with increasing irradiation time, which is proposed to be attributed to the gradual disappearance of oxygen-containing functional groups in GO during the UV-induced reduction reaction process. Fourier transform infrared spectrum and Raman spectrum were used to confirm the reduction of GO under UV irradiation. Our study would give an insight into understanding the transformation of GO’s electronic structures during the reduction process.

36 MATERIALS SCIENCE↗
DOE OSTI2025

On-Surface Reactions of Electronically Active Self-Assembled Monolayers for Electrode Work Function Tuning

Self-assembled monolayers (SAMs) help improve the performance of organic electronic devices through interface passivation and enhanced carrier transport. Yet, there is limited information regarding the chemical structure of the SAMs upon functionalization and subsequent thermal treatment. Here, we studied the on-surface reaction of carbazole-derived SAMs on model gold electrodes, focusing on the chemical structure changes induced by thermal treatments. Furthermore, we correlate the microscopic changes with their impact on the electrode’s work function. The carbazole-based SAMs first transform into organometallic complexes. At higher annealing temperatures, SAMs convert to oligomeric complexes. The observed chemical reactions significantly reduce the electrode work function and facilitate electron injection in n-type organic thin-film transistors. Our results highlight the on-surface synthesis of electronically active SAMs as an alternative approach for modifying the work function of electrodes for organic electronics.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2015

Work function variation of MoS{sub 2} atomic layers grown with chemical vapor deposition: The effects of thickness and the adsorption of water/oxygen molecules

The electrical properties of two-dimensional atomic sheets exhibit remarkable dependences on layer thickness and surface chemistry. Here, we investigated the variation of the work function properties of MoS{sub 2} films prepared with chemical vapor deposition (CVD) on SiO{sub 2} substrates with the number of film layers. Wafer-scale CVD MoS{sub 2} films with 2, 4, and 12 layers were fabricated on SiO{sub 2}, and their properties were evaluated by using Raman and photoluminescence spectroscopies. In accordance with our X-ray photoelectron spectroscopy results, our Kelvin probe force microscopy investigation found that the surface potential of the MoS{sub 2} films increases by ∼0.15 eV when the number of layers is increased from 2 to 12. Photoemission spectroscopy (PES) with in-situ annealing under ultra high vacuum conditions was used to directly demonstrate that this work function shift is associated with the screening effects of oxygen or water molecules adsorbed on the film surface. After annealing, it was found with PES that the surface potential decreases by ∼0.2 eV upon the removal of the adsorbed layers, which confirms that adsorbed species have a role in the variation in the work function.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2018

Improving the Work Function of Nitrogen-Doped Niobium Surfaces for SRF Cavities by Plasma Processing

Work function and surface chemistries of SiC-polished, electropolished, and nitrogen-doped niobium coupons were analyzed before and after plasma processing using a neon-oxygen gas mixture. These studies represent an initial enquiry into the feasibility of applying the plasma processing technique designed at ORNL for the Spallation Neutron Source (SNS) to the nitrogen-doped Nb cavities for the Coherent Light Source II (LCLS-II). Work function of all measured samples was increased after plasma processing, which indicates the strong potential of the plasma processing technique as a tool for increasing the accelerating gradient of nitrogen-doped cavities.

43 PARTICLE ACCELERATORS↗
DOE OSTI2013

High work-function hole transport layers by self-assembly using a fluorinated additive

The hole transport polymer poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) derives many of its favorable properties from a PSS-rich interfacial layer that forms spontaneously during coating. Since PEDOT:PSS is only usable as a blend it is not possible to study PEDOT:PSS without this interfacial layer. Through the use of the self-doped polymer sulfonated poly(thiophene-3-[2-(2-methoxyethoxy) ethoxy]-2,5-diyl) (S-P3MEET) and a polyfluorinated ionomer (PFI) it is possible to compare transparent conducting organic films with and without interfacial layers and to understand their function. Using neutron reflectometry, we show that PFI preferentially segregates at the top surface of the film during coating and forms a thermally stable surface layer. Because of this distribution we find that even small amounts of PFI increase the electron work function of the HTL. We also find that annealing at 150°C and above reduces the work function compared to samples heated at lower temperatures. Using near edge x-ray absorption fine structure spectroscopy and gas chromatography we show that this reduction in work function is due to S-P3MEET being doped by PFI. Organic photovoltaic devices with S-P3MEET/PFI hole transport layers yield higher power conversion efficiency than devices with pure S-P3MEET or PEDOT:PSS hole transport layers. Additionally, devices with a doped interface layer of S-P3MEET/PFI show superior performance to those with un-doped S-P3MEET.

14 SOLAR ENERGY↗