SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A perturbation guidance scheme is developed to keep a tilt-rotor VTOL aircraft close to a predetermined nominal flight path during take-off and landing. A simulation of the guidance scheme applied to the Bell Model 266 tilt-rotor VTOL gave satisfactory behavior in the presence of initial errors and wind disturbances.
A technique has been developed for calculating feedback and feedforward gain matrices that stabilize a VTOL aircraft while enabling it to track input commands of forward and vertical velocity. Leverrier's algorithm is used in a procedure for determining a set of state variable, feedback gains that force the closed loop poles and zeroes of one pilot input transfer function to be at preselected positions in the s plane. This set of feedback gains is then used to calculate the feedback and feedforward gains for the velocity command controller. The method is computationally attractive since the gains are determined by solving systems of linear, simultaneous equations. Responses obtained using a digital simulation of the longitudinal dynamics of the CH-47 helicopter are presented.
Alternate flight control system with power requirements for VTOL aircraft
Hovering and low speed flight capabilities of tilt wing VTOL aircraft in terminal area under near-zero visibility instrument landing conditions
Aeroelastic and dynamic studies which complement and extend various aspects of technology applicable to tilt-rotor VTOL aircraft are discussed. Particular attention is given to proprotor/pylon whirl instability, a precession-type instability akin to propeller/nacelle whirl flutter. The blade flapping and pitch-change freedoms of a proprotor are shown to lead to a fundamentally different situation as regards the manner in which the precession-generated aerodynamic forces and moments act on the pylon and induce whirl flutter relative to that of a propeller. The implication of these forces and moments with regard to their capacity for instigating a whirl instability is examined, demonstrating why a proprotor can exhibit whirl flutter in either the backward or forward directions in contrast to a propeller which is found to always whirl in the backward direction. Analytical trend studies delineating the effect of several system design parameters on proprotor/pylon stability and response are shown.
Utilizing the unique opportunity created by full scale hover testing of the twin-jet Grumman Design 698 VTOL aircraft in the NASA-Ames Hover Facility, a series of experiments was conducted to evaluate the effectivness of scale model testing in predicting full scale behavior. Interference forces were found to be sensitive to aircraft lower surface geometry, but when the geometry was modeled accurately the small scale results matched full scale forces guite well. The interference forces were found to be insensitive to core nozzle temperature and fan nozzle pressure ratio. The results clearly demonstrate that small scale models can be reliably utilized for aircraft and technology development when the appropriate sensitivities are recognized.
A flow visualization study of several configurations of a jet-powered vertical takeoff and landing (VTOL) aircraft model during hover in ground effect was conducted. A surface oil flow technique was used to observe the flow patterns on the lower surfaces of the model. There were significant configuration effects. Wing height with respect to fuselage, the presence of an engine inlet duct beside the fuselage, and nozzle pressure ratio are seen to have strong effects on the surface flow angles on the lower surface of the wing. This test was part of a program to improve the methods for predicting the hot gas ingestion (HGI) for jet-powered vertical/short takeoff and landing (V/STOL) aircraft. The tests were performed at the Jet Calibration and Hover Test (JCAHT) Facility at Ames Research Center.
Flight records are presented from an early flight test of a wing-tip mounted tilting-ducted-fan, vertical-take-off and landing (VTOL) aircraft configuration. Time histories of the aircraft motions, control positions, and duct pitching-moment variation are presented to illustrate the characteristics of the aircraft in hovering, in conversion from hovering to forward flight, and in conversion from forward flight to hovering. The results indicate that during essentially continuous slow level- flight conversions, this aircraft experiences excessive longitudinal trim changes. Studies have shown that the large trim changes are caused primarily by the variation of aerodynamic moments acting on the duct units. Action of the duct-induced downwash on the horizontal stabilizer during the conversion also contributes to the longitudinal trim variations. Time histories of hovering and slow vertical descent in the final stages of landing in calm air show angular motions of the aircraft as great as +/- 10 deg. about all axes. Stick and pedal displacements required to control the aircraft during the landing maneuver were on the order of 50 to 60 percent of the total travel available.
Spiral approaches adjacent to the active runways of CTOL airports have been proposed as a means of effectively interfacing CTOL and VTOL landing operations. Assuming an airport equipped with a Microwave Landing System (MLS), a VTOL aircraft following a spiral approach path might, depending on the specific trajectory, pass alternatively in and out of the linear coverage of the MLS and thereby suffer degraded navigation performance. The objective of this study was to employ essentially state-of-the-art aided inertial navigation concepts to explore the expected navigation performance operating in the environment just described. Results show that aided inertial concepts utilizing simple body-mounted inertia systems may be adequate for an instrument landing if the MLS azimuth and Distance Measuring Equipment (DME) signal coverages extend to within a few feet of the ground.
This paper presents the results of an analytical study of the dynamics and control of turbofan lift engines, and proposes methods of meeting the response requirements imposed by the VTOL aircraft application. Two types of lift fan engines are discussed: the integral and remote. The integral engine is a conventional two-spool, high bypass ratio turbofan designed for low noise and short length. The remote engine employs a gas generator and a lift fan which are separated by a duct, and which need not be coaxial. For the integral engine, a control system design is presented which satisfies the VTOL response requirements. For the remote engine, two unconventional methods of control involving flow transfer between lift units are discussed.
A motion simulator study was conducted to determine the effects of roll and pitch stabilization on the handling qualities and control power requirements of VTOL aircraft during hover and short-distance maneuvering flight. Three levels of stabilization complexity were compared: (1) no stabilization, (2) rate stabilization, and (3) attitude stabilization. Control sensitivities and stabilization gains were optimized prior to comparison. Results are presented to show how the optimum systems were determined and how they compared with each other at different levels of control power. Comparisons were made both in calm air and in the presence of roll disturbances. Results indicate the attitude-stabilized system provides the best handling qualities for the least amount of control power.
This paper describes a detailed mathematical model which has been assembled to study automatic approach and landing guidance concepts to bring a VTOL aircraft onto a small aviation ship. The model is used to formulate system simulations which in turn are used to evaluate different guidance concepts. Ship motion (Sea State 5), wind-over-deck turbulence, MLS-based navigation, implicit model following flight control, lift fan V/STOL aircraft, ship and aircraft instrumentation errors, various steering laws, and appropriate environmental and human factor constraints are included in the model. Results are given to demonstrate use of the model and simulation to evaluate performance of the flight system and to choose appropriate guidance techniques for further cockpit simulator study.
The paper deals with the Triscan concept - a dual-antenna microwave landing guidance system, using triangulation for close-in accuracy - developed to facilitate the landing of VTOL aircraft on ships in all-weather conditions. Analysis of the navigation performance of an onboard system receiving data from Triscan and data-linked information regarding the motion of the ship showed that the approach navigation performance depends on the approach path profile flown, the magnitude of the measurement bias error, and the navigation system's knowledge of the shipboard landing pad motion, which was implemented through the concept of a landing pad deviation vector.
An engineering methodology based on an empirical data base and analytical fluid dynamic models was developed for the prediction of propulsive lift system induced aerodynamic effects for multiple lift jet VTOL aircraft operating in the hover mode in and out of ground effect. The effects of aircraft geometry, aircraft orientation (pitch, roll) as well as height above ground are considered. Lift jet vector and splay directions fit the airframe, lift jet exit flow conditions, and both axisymmetric and rectangular nozzle exit geometry are also accommodated. The induced suckdown flows are computed from the potential flowfield induced by the turbulent entrainment of both the free jets and wall jets in ground effect and from the free jets alone out of ground effect. The methodology emphasized geometric considerations, computation of stagnation lines and fountain upwash inclination, fountain upwash formation and development, and fountain impingement on the airframe.
Explore the source record for details and available documents.
A toolchain and process for conceptual design of VTOL rotorcraft, employing low- and mid-fidelity tools is presented. The approach is capable of providing more quantitatively-credible trades between noise, size, and cost metrics than the methods commonly used for conceptual design. In addition to a general conceptual design tool, the approach employs comprehensive analysis for trim, blade motion, and airloads; these are then used by acoustic analysis software to develop source sound, propagate it, and calculate noise metrics. A key aspect of the approach is flexibility to assess varied aircraft types and different technologies and design features. Vehicles are sized using a representative Urban Air Mobility design mission. Demonstration cases are presented for a single main rotor helicopter, quadrotor, side-by-side helicopter, and lift+cruise aircraft. Noise metrics used for demonstration are the FAA/EASA certification Effective Perceived Noise Levels for takeoff, flyover, and approach. The concept aircraft in this study are shown to achieve reductions in noise relative the initial design points, with changes in mission performance and cost as a consequence. Many of the designs are predicted to be tens of EPNdB quieter in the certification metrics than existing helicopters.
The emerging Urban Air Mobility market imposes new design requirements on aircraft, including the ability to have vertical take-off and landing (VTOL) capabilities with the ability to transition into fast and efficient forward flight. Industry has proposed many different vehicle configurations, which have many different challenges. A primary challenge facing many of these concepts is flight through the transition corridor from vertical to horizontal flight and back. In an effort to better understand and help improve vehicle safety in the complex transition corridors, NASA Langley Research Center has proposed to characterize the transition corridor with wind tunnel and flight tests for a variety of unmanned aircraft system sized VTOL configurations. The first vehicle of this series is the Langley Aerodrome 8 (LA-8). LA-8 is a high-risk/high-reward tandem tilt-wing vehicle with distributed electric propulsion and a partially deflected slipstream aircraft. The LA-8 vehicle has gone through a preliminary wind tunnel test in NASA Langley's 12-Foot Low-Speed Wind Tunnel. The results of the aerodynamic data collected, including the longitudinal, lateral, and directional force and moment aerodynamic coefficients, from these tests during different phases of flight are presented.
Urban Air Mobility (UAM) vertical takeoff and landing (VTOL) aircraftdesigns frequently include multiple distributed propulsors, complex wing-propulsor aerodynamics, significant airframe configuration changes during normal flight operations, and no historical database regarding the best ways to transition between vertical and horizontal flight. This paper describes the methodology used for wind tunnel testing of the Langley Aerodrome No. 8 (LA-8) in the NASA Langley 12-Foot Low-SpeedTunnel during multiple test entries in 2019 and2020. The LA-8 is a tandem tilt-wing aircraft with 4 motor-propellerunits and 4 control surfaces distributed across each wing, plus an inverted V-tail with 2 ruddervators on the fuselage. An initial tunnel entryused one-factor-at-a-time (OFAT) testing to (1) define candidate trimmed transition corridors between vertical and horizontal flight, (2) assess whether there was adequate control authority, and (3) define appropriatetest factor ranges for subsequent design of experiment (DOE) wind tunnel testing. The total number of independent variables for these wind tunnel tests (23) made DOE testing an efficient option for assessing the large number of potential interactions associated with the LA-8. The general advantages and disadvantages of OFAT and DOE wind tunnel testing techniques are also discussed –along with the benefits of a combined approach