Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VERTICAL FIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Aerodynamic enhancement of space transportation systems

The results of a number of recent investigations are reviewed and used to demonstrate gains in launch, orbital transfer, and planetary vehicle performance and economy that can result from the proper exploitation of aerodynamic phenomena. For launch vehicles, application of control-configured design is shown to allow substantial reduction in wing and vertical fin area (and hence, weight) while maintaining acceptable vehicle performance and control. For orbital transfer and planetary vehicles, the use of aerodynamic lift and drag to reduce retropropulsion requirements is shown to produce payload increases of up to 100 percent and to enable some planetary missions that are not feasible with all-propulsive vehicles. Finally, the application of various advanced technologies to a complete set of launch and orbit transfer vehicles in an early space industrialization mission scenario is considered.

Walberg, G. D.↗
NASA NTRS1982

Durability of commercial aircraft and helicopter composite structures

The development of advanced composite technology during the past decade is discussed. Both secondary and primary components fabricated with boron, graphite, and Kevlar composites are evaluated. Included are spoilers, rudders, and fairings on commercial transports, boron/epoxy reinforced wing structure on C-130 military transports, and doors, fairings, tail rotors, vertical fins, and horizontal stabilizers on commercial helicopters. The development of composite structures resulted in advances in design and manufacturing technology for secondary and primary composite structures for commercial transports. Design concepts and inspection and maintenance results for the components in service are reported. The flight, outdoor ground, and controlled laboratory environmental effects on composites were also determined. Effects of moisture absorption, ultraviolet radiation, aircraft fuels and fluids, and sustained tensile stress are included. Critical parameters affecting the long term durability of composite materials are identified.

Dexter, H. B.↗
NASA NTRS1982

Processing composite materials

The fabrication of several composite structural articles including DC-10 upper aft rudders, L-1011 vertical fins and composite biomedical appliances are discussed. Innovative composite processing methods are included.

R. M. Baucom↗
NASA NTRS1982

Durability of aircraft composite materials

Confidence in the long term durability of advanced composites is developed through a series of flight service programs. Service experience is obtained by installing secondary and primary composite components on commercial and military transport aircraft and helicopters. Included are spoilers, rudders, elevators, ailerons, fairings and wing boxes on transport aircraft and doors, fairings, tail rotors, vertical fins, and horizontal stabilizers on helicopters. Materials included in the evaluation are boron/epoxy, Kevlar/epoxy, graphite/epoxy and boron/aluminum. Inspection, maintenance, and repair results for the components in service are reported. The effects of long term exposure to laboratory, flight, and outdoor environmental conditions are reported for various composite materials. Included are effects of moisture absorption, ultraviolet radiation, and aircraft fuels and fluids.

H. Benson Dextern↗
NASA NTRS1983

Flight service evaluation of composite components on Bell 206L and Sikorsky S-76 helicopters

Progress on two programs to evaluate composite structural components in flight service on commercial helicopters is described. Thirty-six ship sets of composite components that include the litter door, baggage door, forward fairing, and vertical fin were installed on Bell Model 206L helicopters that are operating in widely different climatic areas. Four horizontal stabilizers and ten tail rotor spars that are production components on the S-76 helicopter were tested after prescribed periods of service to determine the effects of the operating environment on their performance. Concurrent with the flight evaluation, specimens from materials used to fabricate the components were exposed in ground racks and tested at specified intervals to determine the effects of outdoor environments. Results achieved from 14,000 hours of accumulated service on the 206L components, tests on a S-76 horizontal stabilizer after 1600 hours of service, tests on a S-76 tail rotor spar after 2300 hours service, and two years of ground based exposure of material coupons are reported.

Baker, D. J.↗
NASA NTRS1983

Safe structures for future aircraft

The failure mechanisms, design lessons, and test equipment employed by NASA in establishing the airworthiness and crashworthiness of aircraft components for commercial applications are described. The composites test programs have progressed to medium primary structures such as stabilizers and a vertical fin. The failures encountered to date have been due to the nonyielding nature of composites, which do not diffuse loads like metals, and the presence of eccentricities, irregular shapes, stiffness changes, and discontinuities that cause tension and shear. Testing to failure, which always occurred in first tests before the design loads were reached, helped identify design changes and reinforcements that produced successful products. New materials and NDE techniques are identified, together with aircraft structural design changes that offer greater protection to the passengers, fuel antimisting agents, and landing gear systems.

Mccomb, H. G., Jr.↗
NASA NTRS1984

Lightning attachment patterns and flight conditions experienced by the NASA F-106B airplane from 1980 to 1983

The direct lightning strike data and associated flight conditions recorded from 1980 to 1983 during 742 thunderstorm penetrations with a NASA F-106B in Oklahoma and Virginia are studied with an emphasis on aircraft protection design. The individual lightning attachment spots were plotted on isometric projections of the aircraft to identify lightning entry and exit points and swept flash patterns. The altitudes, ambient temperatures, turbulence, and precipitation at which the strikes occurred are summarized and discussed. It was noted that peak strike rates (0.81 strikes/min and 3 strikes/penetration) occurred at altitudes between 11 km and 11.6 km corresponding to ambient temperatures between -40 C and -45 C. The data confirmed that initial entry and exit points most frequently occur at aircraft extremities, in this case the nose boom, the wing tips, the vertical fin cap, and the afterburner. The swept-flash attachment paths and burn marks found in this program indicate that the mid-span areas of swept aircraft may be more susceptible to lightning than previously thought. It was also found that lightning strikes may attach to spots within the engine tail pipe.

Fisher, B. D.↗
NASA NTRS1982

Advanced manufacturing development of a composite empennage component for L-1011 aircraft

This is the final report of technical work conducted during the fourth phase of a multiphase program having the objective of the design, development and flight evaluation of an advanced composite empennage component manufactured in a production environment at a cost competitive with those of its metal counterpart, and at a weight savings of at least 20 percent. The empennage component selected for this program is the vertical fin box of the L-1011 aircraft. The box structure extends from the fuselage production joint to the tip rib and includes front and rear spars. During Phase 4 of the program, production quality tooling was designed and manufactured to produce three sets of covers, ribs, spars, miscellaneous parts, and subassemblies to assemble three complete ACVF units. Recurring and nonrecurring cost data were compiled and documented in the updated producibility/design to cost plan. Nondestruct inspections, quality control tests, and quality acceptance tests were performed in accordance with the quality assurance plan and the structural integrity control plan. Records were maintained to provide traceability of material and parts throughout the manufacturing development phase. It was also determined that additional tooling would not be required to support the current and projected L-1011 production rate.

Alva, T.↗
NASA NTRS1985

Low-speed experimental study of the vortex flow effects of a fighter forebody having unconventional cross-section

A low speed wind tunnel investigation is conducted for the vortex flow characteristics of a tailless fighter configuration that features full length, fuselage-blended forebody strakes. Static pressure distributions were obtained on the forebody upper surface, and six-component forces and moments were measured on the complete, 60-deg cropped delta wing-fuselage-centerline vertical fin model at angles of attack and sideslip respectively reaching 50 deg and + or - 20 deg. The surface pressure data reveal that development of concentrated vortices from the sharp edged forebody strakes occurred at moderate and high angles of attack. The blended forebody was effective in capturing the windward vortical flow up to high incidence and sideslip angles. The direct suction effect of the windward vortex on the forebody sidewall was the primary contributor to static directional stability at high angles of attack. These improvements are potentially offset, however, by reduced or unstable roll and yaw damping.

Erickson, G. E.↗
NASA NTRS1986

Flight service evaluation of composite components on the Bell helicopter model 206L

This is the second annual report on the flight service components for the Bell Model 206L JetRanger helicopter. The components have been placed in service in the Continental United States, Canada, and Alaska. The report covers the period from 1 August 1983 to 1 January 1986. The status of 34 sets of components is discussed in this report. Approximately 73,000 flight hours were accumulated on the components as of 1 January 1986. Three years of coupon tests on the components are presented with test results. A vertical fin had been struck by lightning and the results of its examination and tests are included.

Wilson, H. E., II↗
NASA NTRS1986

Wind-tunnel investigation of the flight characteristics of a canard general-aviation airplane configuration

A 0.36-scale model of a canard general-aviation airplane with a single pusher propeller and winglets was tested in the Langley 30- by 60-Foot Wind Tunnel to determine the static and dynamic stability and control and free-flight behavior of the configuration. Model variables made testing of the model possible with the canard in high and low positions, with increased winglet area, with outboard wing leading-edge droop, with fuselage-mounted vertical fin and rudder, with enlarged rudders, with dual deflecting rudders, and with ailerons mounted closer to the wing tips. The basic model exhibited generally good longitudinal and lateral stability and control characteristics. The removal of an outboard leading-edge droop degraded roll damping and produced lightly damped roll (wing rock) oscillations. In general, the model exhibited very stable dihedral effect but weak directional stability. Rudder and aileron control power were sufficiently adequate for control of most flight conditions, but appeared to be relatively weak for maneuvering compared with those of more conventionally configured models.

Satran, D. R.↗
NASA NTRS1984

Advanced manufacturing development of a composite empennage component for L-1011 aircraft. Phase 3: Production readiness verification testing

Twenty-two specimens of each of two key structural elements of the Advance Composite Vertical Fin (ACVF) were fabricated and tested. One element represented the front spar at the fuselage attachment area and the other element represented the cover at the fuselage joint area. Ten specimens of each element were selected for static testing. The coefficient of variation resulting from the tests was 3.28 percent for the ten cover specimens and 6.11 percent for the ten spar specimens, which compare well with metallic structures. The remaining twelve cover and twelve spar specimens were durability tested in environmental chambers which permitted the temperature and humidity environment to be cycled as well as the applied loads. Results of the durability tests indicated that such components will survive the service environment.

Jackson, A.↗
NASA NTRS1986

Evaluation of composite components on the Bell 206L and Sikorsky S-76 helicopter

A development flight testing status evaluation is presented for composite material structural components used in the Bell 206L and Sikorsky S-76 commercial helicopters, encompassing litter doors, baggage doors, forward fairings, and vertical fins. These flight tests have been conducted in various climatic conditions. The materials used in the fabrication of these components are also undergoing a separate exposure and testing program. Attention is given to results of 73,000 hrs of accumulated flight time on 206L components and 50,000 hrs on S-76 components.

Baker, Donald J.↗
NASA NTRS1987

High-angle-of-attack stability and control improvements for the EA-6B Prowler

The factors involved in high-angle-of-attack directional divergence phenomena for the EA-6B ECM aircraft have been investigated in NASA-Langley wind tunnel facilities in order to evaluate airframe modifications which would eliminate or delay such divergence to angles-of-attack farther removed from the operational flight envelope of the aircraft. The results obtained indicate that an adverse sidewash at the aft fuselage and vertical tail location is responsible for the directional stability loss, and that the sidewash is due to a vortex system generated by the fuselage-wing juncture. Modifications encompassing a wing inboard leading edge droop, a wing glove strake, and a vertical fin extension, have significantly alleviated the stability problem.

Jordan, Frank L.↗
NASA NTRS1987

Lightning discharge protection rod

A system for protecting an in-air vehicle from damage due to a lighning strike is disclosed. It is an extremely simple device consisting of a sacrificial graphite composite rod, approximately the diameter of a pencil with a length of about five inches. The sacrificial rod is constructed with the graphite fibers running axially within the rod in a manner that best provides a path of conduction axially from the trailing edge of an aircraft to the trailing end of the rod. The sacrificial rod is inserted into an attachment hole machined into trailing edges of aircraft flight surfaces, such as a vertical fin cap and attached with adhesive in a manner not prohibiting the conduction path between the rod and the aircraft. The trailing end of the rod may be tapered for aerodynamic and esthetic requirements. This rod is sacrificial but has the capability to sustain several lightning strikes and still provide protection.

Bryan, Charles F., Jr.↗
NASA NTRS1989

Coupled rotor/fuselage dynamic analysis of the AH-1G helicopter and correlation with flight vibrations data

Under a research program designated Design Analysis Methods for VIBrationS (DAMVIBS), existing analytical methods are used for calculating coupled rotor-fuselage vibrations of the AH-1G helicopter for correlation with flight test data from an AH-1G Operational Load Survey (OLS) test program. The analytical representation of the fuselage structure is based on a NASTRAN finite element model (FEM), which has been developed, extensively documented, and correlated with ground vibration test. One procedure that was used for predicting coupled rotor-fuselage vibrations using the advanced Rotorcraft Flight Simulation Program C81 and NASTRAN is summarized. Detailed descriptions of the analytical formulation of rotor dynamics equations, fuselage dynamic equations, coupling between the rotor and fuselage, and solutions to the total system of equations in C81 are included. Analytical predictions of hub shears for main rotor harmonics 2p, 4p, and 6p generated by C81 are used in conjunction with 2p OLS measured control loads and a 2p lateral tail rotor gearbox force, representing downwash impingement on the vertical fin, to excite the NASTRAN model. NASTRAN is then used to correlate with measured OLS flight test vibrations. Blade load comparisons predicted by C81 showed good agreement. In general, the fuselage vibration correlations show good agreement between anslysis and test in vibration response through 15 to 20 Hz.

Corrigan, J. C.↗
NASA NTRS1989

Stability boundaries for aircraft with unstable lateral-directional dynamics and control saturation

Aircraft that do not possess inherent (aerodynamic) stability must rely on closed-loop control systems for stable operation. Because there are limits on the deflections of an aircraft's control surfaces, the region of stable operation also is bounded. These boundaries are investigated for a lateral-directional example in which vertical fin size is inadequate to provide directional stability and where aileron and rudder deflections are subject to saturation. Fourth-order models are used in this study, with flight control logic based on minimum-control-energy linear-quadratic-regulatory theory. It is found that the stability boundaries can be described by unstable limit cycles surrounding stable equilibrium points. Variations in regions of stability with gain levels and command inputs are illustrated. Current results suggest guidelines for permissible limits on the open-loop instability of an aircraft's lateral-directional modes.

Shrivastava, Prakash C.↗