Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Upper regularity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Stable Calibration of Raman Lidar Water-Vapor Measurements

A method has been devised to ensure stable, long-term calibration of Raman lidar measurements that are used to determine the altitude-dependent mixing ratio of water vapor in the upper troposphere and lower stratosphere. Because the lidar measurements yield a quantity proportional to the mixing ratio, rather than the mixing ratio itself, calibration is necessary to obtain the factor of proportionality. The present method involves the use of calibration data from two sources: (1) absolute calibration data from in situ radiosonde measurements made during occasional campaigns and (2) partial calibration data obtained by use, on a regular schedule, of a lamp that emits in a known spectrum determined in laboratory calibration measurements. In this method, data from the first radiosonde campaign are used to calculate a campaign-averaged absolute lidar calibration factor (t(sub 1)) and the corresponding campaign-averaged ration (L(sub 1)) between lamp irradiances at the water-vapor and nitrogen wavelengths. Depending on the scenario considered, this ratio can be assumed to be either constant over a long time (L=L(sub 1)) or drifting slowly with time. The absolutely calibrated water-vapor mixing ratio (q) obtained from the ith routine off-campaign lidar measurement is given by q(sub 1)=P(sub 1)/t(sub 1)=LP(sub 1)/P(sup prime)(sub 1) where P(sub 1) is water-vapor/nitrogen measurement signal ration, t(sub 1) is the unknown and unneeded overall efficiency ratio of the lidar receiver during the ith routine off-campaign measurement run, and P(sup prime)(sub 1) is the water-vapor/nitrogen signal ratio obtained during the lamp run associated with the ith routine off-campaign measurement run. If L is assumed constant, then the lidar calibration is routinely obtained without the need for new radiosonde data. In this case, one uses L=L(sub 1) = P(sup prime)(sub 1)/t(sub 1), where P(sub 1)(sup prime) is the water-vapor/nitrogen signal ratio obtained during the lamp run associated with the first radiosonde campaign. If L is assumed to drift slowly, then it is necessary to postpone calculation of a(sub 1) until after a second radiosonde campaign. In this case, one obtains a new value, L(sub 2), from the second radiosonde campaign, and for the ith routine off-campaign measurement run, one uses an intermediate value of L obtained by simple linear time interpolation between L(sub 1) and L(sub 2).

Leblanc, Thierry↗
NASA NTRS1987

Equatorial long-wave characteristics determined from satellite sea surface temperature and in situ data

SST maps and imagery derived from the NOAA 6 satellite AVHRR for June and July 1981 in the eastern tropical Pacific portray the wavelike structure of the cool water along the equator from 93 deg W to 125 deg W. Cusped waves of approximately 1000-km zonal wavelength and 25-day period propagated westward with a phase speed of 40 km/day. The observed meridional extent between the crest and trough of the waves is about 300 km. Details in the imagery show cooler water at the cusps advected north and then east with the north equatorial countercurrent (NECC), consistent with the suggestion of a series of anticyclonic eddies occupying the shear zone between the NECC and the westward flowing south equatorial current. Absolute SST estimates from the AVHRR data agree to within 0.6 C with shipboard data taken along 110 deg W between 5 deg N and 5 deg S. The wavelike structures in the SST maps are also in agreement at the surface with a vertical expendable bathythermograph temperature section made along the equator between 93 deg W and 125 deg W, which shows the phase of the waves tilting westward with increasing depth over the upper 75 m. Such a phase shift, if it extended 100-200 km meridionally in either direction from the equator, would be associated with an equatorward flux of heat. Similar phase shifts appear in temperature time series at depths of 20 and 50 m, from a mooring at 0-deg 33-min N, 110-deg 30-min W. Near-surface currents measured at this and a second mooring on the equator at 109-deg 40-min W indicate a regular pattern of northward advection when wave cusps pass them, followed by southwest flow during the passage of wave troughs, again consistent with an equatorward flux of heat, as well as with earlier theoretical and drift buoy findings.

Pullen, Patricia E.↗
NASA NTRS2020

Modeling the Uncertainties of Solar System Ephemerides for Robust Gravitational-wave Searches with Pular-timing Arrays

The regularity of pulsar emissions becomes apparent once we reference the pulses’ times of arrivals to the inertial rest frame of the solar system. It follows that errors in the determination of Earthʼs position with respect to the solar system barycenter can appear as a time-correlated bias in pulsar-timing residual time series, affecting the searches for low-frequency gravitational waves performed with pulsar-timing arrays. Indeed, recent array data sets yield different gravitational-wave background upper limits and detection statistics when analyzed with different solar system ephemerides. Crucially, the ephemerides do not generally provide usable error representations. In this article, we describe the motivation, construction, and application of a physical model of solar system ephemeris uncertainties, which focuses on the degrees of freedom (Jupiterʼs orbital elements) most relevant to gravitational-wave searches with pulsar-timing arrays. This model, BAYESEPHEM, was used to derive ephemeris-robust results in NANOGravʼs 11 yr stochastic-background search, and it provides a foundation for future searches by NANOGrav and other consortia. The analysis and simulations reported here suggest that ephemeris modeling reduces the gravitational-wave sensitivity of the 11 yr data set and that this degeneracy will vanish with improved ephemerides and with pulsar-timing data sets that extend well beyond a single Jovian orbital period.

M Vallisneri↗
NASA NTRSDate not supplied

Gigatraj: An Atmospheric Trajectory Model

Atmospheric trajectory models have a long history of success in tracking air motions in the lower stratosphere and upper troposphere over periods of up to a few days. Parcels have been traced backwards from observations to identify whatever phenomena (strong convection, volcanic eruptions, rocket launches, etc.) put their signature on them. Parcels have also been initialized at a known event and traced forward to examine their subsequent physical and chemical evolution. We describe a new trajectory model, "gigatraj," that aims to increase exibility by (a) making it straightforward to use new meteorological data sources, including those not based on regular latitude-longitude grids; (b) enabling a run-time choice of vertical coordinate system for kinematic and/or quasi-isentropic calculations; (c) allowing for the output of arbitrary meteorological products, selectable by the user and interpolated to the parcels' locations and times. The model can be run in a serial or parallel processing environment, so that large numbers of parcels can be traced in a reasonable time. Information is presented on model accuracy and performance. The former is demonstrated by runs using both test-pattern winds (comparing expected paths with actual output) and real-world winds (comparing forward and backward runs to characterize how well parcels retrace their paths). Sample cases are also shown, including a reverse domain lling (RDF) calculation illustrating a tropopause fold event. Model output can be displayed using the new Visualization And Lagrangian dynamics Immersive eXtended Reality (VALIXR) system, and an example will be shown. In addition, we describe work to incorporate a version of gigatraj into the Goddard Earth Observing System (GEOS) of NASA's Global Modeling and Assimilation O ce (GMAO) at Goddard Space Flight Center. This enables trajectory calculations to be performed within the running GEOS model at the latter's native time resolution, instead of using the winds from every few hours. It also provides access to all of GEOS's internal variables as they are calculated. This module may be useful, for example, for tracking rapid chemical changes in a Lagrangian framework.

dynamics↗
NASA NTRS1986

A search for the prewetting line

This paper describes efforts to locate the prewetting line in a binary liquid system (isopropanol-perfluoromethylcyclohexane) at the vapor-liquid interface. Tight upper bounds were placed on the temperature separation (0.2 K) between the prewetting line and the line of bulk liquid phase separation. The prewetting line in systems at equilibrium was not detected. Experimental signatures indicative of the prewetting line occurred only in nonequilibrium situations. Several theories predict that the adsorption of one of the components (the fluorocarbon, in this case) at the liquid-vapor interface should increase abruptly, at a temperature sightly above the temperature at which the mixture separates into two liquid phases. A regular solution calculation indicates that this prewetting line should have been easily detectable with the instruments used in this experiment. Significant features of the experiment are: (1) low-gradient thermostatting, (2) in situ stirring, (3) precision ellipsometry from the vapor-liquid interface, (4) high resolution differential index of refraction measurements using a novel cell design, and (5) computer control.

Schmidt, J. W.↗
NASA NTRS1988

Constraints on Mars sampling based on models of basaltic flow surfaces and interiors

Recent field observation and numerical modelling of the pattern and origin of vesicle zones and joints in terrestrial basaltic flows has resulted in increased understanding of the processes which affect flow surface morphology. This work has documented the ubiquitous occurrence of three vertical zones in basalt flows: (1) an upper vesicular zone; (2) a middle vesicle-free zone; and (3) a lower vesicular zone. The upper vesicular zone is generally about one-half of the total flow thickness. Computer modeling of the development of these zones confirms that vesicle zonation is a result of the nucleation, growth and rise of bubbles in solidifying lava and can be expected to occur in all basaltic flows. Degradation of basaltic flows, therefore, will produce vesicular blocks until the erosional level reaches the central vesicle-free zone. In addition, observation of terrestrial basaltic flows has shown that most thin (less than 10 m thick) flows have a regular pattern of orthogonal joints in vertical section in which the spacing of joints increases with depth beneath the flow surface. Using these studies we have performed a preliminary analysis of the Viking lander sites.

Aubele, J. C.↗
NASA NTRS1989

Investigation of CAST-10-2/DOA 2 airfoil in NAE high Reynolds number two-dimensional test facility

A common airfoil model with the CAST 10-2/DOA-2 profile and 228 mm (9 inches) chord length was tested. The tests performed in NAE covered the Mach numbers from 0.3 to 0.8 and Reynolds numbers from 10 to 30 million. The model was tested with transition free and with transition fixed at 5 percent chord for both the upper and the lower surfaces. The data obtained were analyzed for the effects of Reynolds number, transition fixing and Mach number. The role of the boundary layer on the displacement effect, the interaction with the shock wave and the trailing edge separation are examined. The results are summarized as follows: (1) the airfoil performance depends strongly on Reynolds number and transition fixing; (2) with transition fixed, the aerodynamic quantities such as lift, pitching moment and drag show a monotonic variation with Reynolds number; (3) with transition free, the aerodynamic quantities vary less regularly with Reynolds number and a slight parametric dependency is shown. The weak dependency is due to the compensatory effect of the forward shift of the transition position and the thinning of the turbulent boundary layer as Reynolds number increases; (4) the shock Mach number and the shock position are weakly dependent on Reynolds number; and (5) the long extent of the laminar boundary layer at transonic speeds reduces the drag appreciably at low Reynolds numbers. The drag bucket around the design Mach number can be observed below Reynolds number 15 million.

Chan, Y. Y.↗
NASA NTRS2023

Latitudinal Variations in Methane Abundance, Aerosol Opacity and Aerosol Scattering Efficiency in Neptune's Atmosphere Determined from VLT/MUSE

Spectral observations of Neptune made in 2019 with the Multi Unit Spectroscopic Explorer (MUSE) instrument at the Very Large Telescope (VLT) in Chile have been analyzed to determine the spatial variation of aerosol scattering properties and methane abundance in Neptune's atmosphere. The darkening of the South Polar Wave at ∼60°S, and dark spots such as the Voyager 2 Great Dark Spot is concluded to be due to a spectrally dependent darkening (λ < 650 nm) of particles in a deep aerosol layer at ∼5 bar and presumed to be composed of a mixture of photochemically generated haze and H 2 S ice. We also note a regular latitudinal variation of reflectivity at wavelengths of very low methane absorption longer than ∼650 nm, with bright zones latitudinally separated by ∼25°. This feature, which has similar spectral characteristics to a discrete deep bright spot DBS-2019 found in our data, is found to be consistent with a brightening of the particles in the same ∼5-bar aerosol layer at λ > 650 nm. We find the properties of an overlying methane/haze aerosol layer at ∼2 bar are, to first-order, invariant with latitude, while variations in the opacity of an upper tropospheric haze layer reproduce the observed reflectivity at methane-absorbing wavelengths, with higher abundances found at the equator and also in a narrow “zone” at 80°S. Finally, we find the mean abundance of methane below its condensation level to be 6%–7% at the equator reducing to ∼3% south of ∼25°S, although the absolute abundances are model dependent.

P. G. J. Irwin↗
NASA NTRS1994

Radiative forcing perturbation due to observed increases in tropospheric ozone at Hohenpeissenberg

The effect on surface temperature due to changes in atmospheric O3 depends highly on the latitude where the change occurs. Previous sensitivity calculations indicate that ozone changes in the upper troposphere and lower stratosphere are more effective in causing surface temperature change (Wang et al., 1980). Long term ground-based observations show that tropospheric ozone, especially at the tropopause region, has been increasing at middle and high latitudes in the Northern Hemisphere (NATO, 1988; Quadrennial Ozone Symposium, 1992). These increases will enhance the greenhouse effect and increase the radiative forcing to the troposphere-surface system, which is opposite to the negative radiative forcing calculated from the observed stratospheric ozone depletion recently reported in WMO (1992). We used more than two thousands regularly measured ozonesondes providing reliable vertical O3 distribution at Hohenpeissenberg (47N; 11E) for the 1967-1990 to study the instantaneous solar and longwave radiative forcing the two decades 1971-1990 and compare the forcing with those caused by increasing CO2, CH4, N2O, and CFCs. Calculations are also made to compare the O3 radiative forcing between stratospheric depletion and tropospheric increase. Results indicate that the O3 changes will induce a positive radiative forcing dominated by tropospheric O3 increase and the magnitude of the forcing is comparable to that due to CO2 increases during the two decades. The significant implications of the tropospheric O3 increase to the global climate are discussed.

Wang, Wei-Chyung↗
NASA NTRS2007

Coronas-F Orbit Monitoring and Re-Entry Prediction

Russian scientific satellite CORONAS-F was launched on July, 31, 2001. The object was inserted in near-circular orbit with the inclination 82.5deg and a mean altitude approx. 520 km. Due to the upper atmosphere drag CORONAS-F was permanently descended and as a result on December, 6, 2005 it has finished the earth-orbital flight, having lifetime in space approx. 4.5 years. The satellite structural features and its flight attitude control led to the significant variations of its ballistic coefficient during the flight. It was a cause of some specific difficulties in the fulfillment of the ballistic and navigation support of this space vehicle flight. Besides the main mission objective CORONAS-F also has been selected by the Inter-Agency Space Debris Coordination Committee (IADC) as a target object for the next regular international re-entry test campaign on a program of surveillance and re-entry prediction for the hazard space objects within their de-orbiting phases. Spacecraft (S/C) CORONAS-F kept its working state right up to the end of the flight - down to the atmosphere entry. This fact enabled to realization of the additional research experiments, concerning with an estimation of the atmospheric density within the low earth orbits (LEO) of the artificial satellites, and made possible to continue track the S/C during final phase of its flight by means of Russian regular command & tracking system, used for it control. Thus there appeared a unique possibility of using for tracking S/C at its de-orbiting phase not only passive radar facilities, belonging to the space surveillance systems and traditionally used for support of the IADC re-entry test campaigns, but also more precise active trajectory radio-tracking facilities from the ground control complex (GCC) applied for this object. Under the corresponding decision of the Russian side such capability of additional high-precise tracking control of the CORONAS-F flight in this period of time has been implemented. The organizing of the CORONAS-F ballistic and navigational support (BNS) and solving its main tasks (such as S/C orbit determination (OD) and its motion prediction and connected with them) both for regular mission stage and for additional flight program were realized by the group of specialists from the Mission Control Center (MCC). MCC was also assigned as a principal organization from the Russian side for participation in the 7th IADC re-entry test campaign on CORONAS-F. The CORONAS-F flight features and space environments circumstances during its flight as well as a methodology and technology of spacecraft ballistic and navigational support are given below. The BNS results for different phases of S/C flight, including the results of its re-entry predictions, obtained during the realization of the 7th IADC test campaign are submitted. The accuracy of space vehicle re-entry prediction and its dependence on various factors are analyzed in more details.

Ivanov, N. M.↗
NASA NTRSDate not supplied

An exact solution of an augmented Burgers equation and amplitude-dependent acoustic propagation speed

Nonlinear sound propagation in the atmosphere is usually modeled using an augmented Burgers equation accounting for a weak nonlinearity and atmospheric absorption. Because the absorption includes the molecular vibrational relaxation, such a Burgers equation is more complex than the regular Burgers equation that only accounts for the thermoviscous dissipation in the absorption. Although an exact solution of the regular Burgers equation has long been derived using the Cole- Hopf transform, an exact solution of the augmented Burgers equation has not been derived previously. Thus, this paper presents an exact solution of the augmented Burgers equation. This novel solution is shown to be equivalent to the solution using the Cole-Hopf transform when the absorption only involves thermoviscous dissipation. It can also be reduced to the known solution of an N-wave when the absorption is ignored. The augmented Burgers equation is an approximation valid for weak nonlinearity. However, this assumption may not be accurate for acoustic signals propagating from the lower atmosphere and which are subsequently refracted downward from the upper atmosphere (e.g., stratosphere and thermosphere) due to the decreasing air density with increasing altitude [Lonzaga, et al., Geophysical Journal International, 200(3), pp.1347-1361]. Consequently, the current paper also discusses the effects of a strong nonlinearity that lead to an amplitude-dependent increase in signal propagation speed. For an impulsive signal such as a sonic boom, these effects cause a dispersion of the signal similar to the observed dispersion of acoustic signals from supersonic Concorde as well as from large explosions.

Joel B Lonzaga↗
NASA NTRS1990

Analytical and Photogrammetric Characterization of a Planar Tetrahedral Truss

Future space science missions are likely to require near-optical quality reflectors which are supported by a stiff truss structure. This support truss should conform closely with its intended shape to minimize its contribution to the overall surface error of the reflector. The current investigation was conducted to evaluate the planar surface accuracy of a regular tetrahedral truss structure by comparing the results of predicted and measured node locations. The truss is a 2-ring hexagonal structure composed of 102 equal-length truss members. Each truss member is nominally 2 meters in length between node centers and is comprised of a graphite/epoxy tube with aluminum nodes and joints. The axial stiffness and the length variation of the truss components were determined experimentally and incorporated into a static finite element analysis of the truss. From this analysis, the root mean square (RMS) surface error of the truss was predicted to be 0.11 mm (0004 in). Photogrammetry tests were performed on the assembled truss to measure the normal displacements of the upper surface nodes and to determine if the truss would maintain its intended shape when subjected to repeated assembly. Considering the variation in the truss component lengths, the measures rms error of 0.14 mm (0.006 in) in the assembled truss is relatively small. The test results also indicate that a repeatable truss surface is achievable. Several potential sources of error were identified and discussed.

Wu, K. Chauncey↗
NASA NTRSDate not supplied

Developing A Continuous Ozone Record Through the SAGE and Aura Missions With NASA Reanalysis Products

During the last quarter of the 20th century, the Stratospheric Aerosol and Gas Experiment (SAGE) missions were crucial in monitoring the loss and the subsequent recovery of the stratospheric ozone layer. Due to the employed solar occultation and self-calibration method, the SAGE monitors have produced stable data throughout the lifetime of each instrument. However, over ten years passed between the end of the SAGE II and SAGE III/M3M missions in 2005 and the launch of SAGE III/ISS instrument in 2017, leaving a gap in the data that much be bridged in order to assess the trends in the ozone record. Reanalysis products, such as the Modern-Era Retrospective analysis for Research and Applications, version 2 (MERRA-2), are attractive candidates for trend analysis due to the statistically optimized combination of multiple observing systems and the regular temporal and spatial coverage. In this study, we explore using the SAGE records to develop a stable reanalysis data product, suitable for trend analysis, from the start of the SAGE II record in 1984 through the present. Changes in the assimilated observation systems can introduce discontinuities within the MERRA-2 ozone record, such as in 2004 when the MERRA-2 system shifted from assimilating ozone retrievals collected by SBUV instruments to those collected by instruments onboard the Aura satellite. We follow the radiative transfer procedure outlined by Wargan et al. (2018) to address discontinuities in the MERRA-2 ozone dataset at the 2004 transition and during the Aura record. SAGE II ozone profiles are used to address discontinuities in upper stratospheric ozone associated with changes in the MERRA-2 meteorological observing system in 1998 and 1995. Lastly, we will use the resulting bias-corrected MERRA-2 ozone fields to assess the relative performance of the data from different SAGE sensors.

SAGE↗
NASA NTRS1996

Calibration of the Microwave Limb Sounder on the Upper Atmosphere Research Satellite

The Microwave Limb Sounder (MLS) is a three-radiometer, passive, limb emission instrument onboard the Upper Atmosphere Research Satellite (UARS). Radiometric, spectral and field-of-view calibrations of the MLS instrument are described in this paper. In-orbit noise performance, gain stability, spectral baseline and dynamic range are described, as well as use of in-flight data for validation and refinement of prelaunch calibrations. Estimated systematic scaling uncertainties (3 sigma) on calibrated limb radiances from prelaunch calibrations are 2.6% in bands 1 through 3, 3.4% in band 4, and 6% in band 5. The observed systematic errors in band 6 are about 15%, consistent with prelaunch calibration uncertainties. Random uncertainties on individual limb radiance measurements are very close to the levels predicted from measured radiometer noise temperature, with negligible contribution from noise and drifts on the regular in-flight gain calibration measurements.

Jarnot, R. F.↗
NASA NTRSDate not supplied

Developing A Continuous Ozone Record Through the SAGE and Aura Missions With NASA Reanalysis Products

During the last quarter of the 20th century, the Stratospheric Aerosol and Gas Experiment (SAGE) missions were crucial in monitoring the loss and subsequent recovery of the stratospheric ozone layer. Due to the employed solar occultation and self-calibration method, the SAGE monitors have produced stable data throughout the lifetime of each instrument. However, over ten years passed between the end of the SAGE II and SAGE III/M3M missions in 2005 and the launch of SAGE III/ISS instrument in 2017, leaving a gap in the data that must be bridged in order to assess trends in the ozone record. The Modern-Era Retrospective analysis for Research and Applications, version 2 (MERRA-2) reanalysis product, with output available starting in 1980, is an attractive candidate for trend analysis due to the statistically optimized combination of multiple observing systems and the regular temporal and spatial coverage. However, changes in the assimilated observation systems can introduce discontinuities within the MERRA-2 ozone record, such as in 2004 when the MERRA-2 system shifted from assimilating ozone retrievals collected by SBUV instruments to those collected by instruments onboard the Aura satellite. In this study, we explore using the SAGE II record as a transfer function to develop a stable reanalysis data product, suitable for trend analysis, from the start of the SAGE II record in 1984 through the present. We follow the procedure outlined by Wargan et al. (2018) to address discontinuities in the MERRA-2 ozone dataset at the 2004 transition and during the Aura record. SAGE II ozone profiles are used to correct discontinuities in upper stratospheric ozone associated with changes in the MERRA-2 meteorological observing system in 1998 and 1995. We will then assess the relative performance of the data from different SAGE sensors using the resulting bias-corrected MERRA-2 ozone fields.

Pamela Wales↗
NASA NTRS2012

Ozone-Temperature Diurnal and Longer Term Correlations, in the Lower Thermosphere, Mesosphere and Stratosphere, Based on Measurements from SABER on TIMED

The analysis of mutual ozone-temperature variations can provide useful information on their interdependencies relative to the photochemistry and dynamics governing their behavior. Previous studies have mostly been based on satellite measurements taken at a fixed local time in the stratosphere and lower mesosphere. For these data, it is shown that the zonal mean ozone amounts and temperatures in the lower stratosphere are mostly positively correlated, while they are mostly negatively correlated in the upper stratosphere and in the lower mesosphere. The negative correlation, due to the dependence of photochemical reaction rates on temperature, indicates that ozone photochemistry is more important than dynamics in determining the ozone amounts. In this study, we provide new results by extending the analysis to include diurnal variations over 24 hrs of local time, and to larger spatial regimes, to include the upper mesosphere and lower thermosphere (MLT). The results are based on measurements by the SABER instrument on the TIMED satellite. For mean variations (i.e., averages over local time and longitude) in the MLT, our results show that there is a sharp reversal in the correlation near 80 km altitude, above which the ozone mixing ratio and temperature are mostly positively correlated, while they are mostly negatively correlated below 80 km. This is consistent with the view that above -80 km, effects due to dynamics are more important compared to photochemistry. For diurnal variations, both the ozone and temperature show phase progressions in local time, as a function of altitude and latitude. For temperature, the phase progression is as expected, as they represent migrating tides. For day time ozone, we also find regular phase progression in local time over the whole altitude range of our analysis, 25 to 105 km, at least for low latitudes. This was not previously known, although phase progressions had been noted by us and by others at lower altitudes. For diurnal variations, we find that between about 40 and 65 km, the ozone amounts and temperatures are mostly negatively correlated or neutral, while below approx. 40 km they are mostly positively correlated or neutral. The correlations are less systematic and less robust than for correlations of the mean. At altitudes above approx.65 km, the correlations are more complex, and depend on the tidal temperature variations. For the diurnal case, consideration needs to be given to transport by thermal tides and to the efficacy of response times of ozone concentrations and temperature to each other.

Huang, Frank T.↗
NASA NTRS1993

The effect of an on-orbit near encounter on the number flux density of micron sized particles

Many materials and techniques have been developed by the authors to sample the flux of particles in Low Earth Orbit (LEO), and through regular insitu sampling of the flux in LEO, the materials and techniques have produced data which complement the data now being amassed by the Long Duration Exposure Facility (LDEF) research activities. Recent flight experiments on STS-32, STS-44, STS-46, and STS-52 have been conducted to develop an understanding of the spatial density as a function of size (mass) for particle sizes 1x10(exp -6) cm and larger. In addition to the enumeration of particle impacts, it was also the intent of these experiments that hypervelocity particles be captured and returned intact. Measurements were performed post-flight to determine the flux density, diameters, and subsequent effects on various optical, thermal control, and structural materials. During the course of the STS-44 mission, the Space Shuttle corrected its altitude by 26 km to evade a spent upper stage. The results of this near encounter suggests that a cloud of micron sized particles exist in the vicinity of the object. Data also suggest that the flux density is nearly two (2) orders of magnitude higher than background flux. A comparison of the number flux density along with microphotographs of the captured particles will be presented for the referenced shuttle flights.

Maag, Carl R.↗
NASA NTRS1982

The spectrum of the Jovian Aurora 1150-1700 A

A series of observations of the northern hemisphere of Jupiter was made in January 1981 using the International Ultraviolet Explorer short-wavelength spectrograph. Exposures of 15 minutes each were made at regular intervals of about 45 minutes around the time when Jupiter's north magnetic pole was tilted toward the earth. The auroral emissions of H Lyman-alpha, and the H2 Lyman- and Werner-bands are seen to emanate from a localized region near the north pole. Their intensity increases and decreases in a periodic way as the planet rotates with the maximum occurring at lambda sub III approximately equal to 185 deg. Using the three observations nearest the observed maximum, a composite spectrum of the aurora is obtained with about 8 A resolution and high signal-to-noise ratio, and many of the H2 Lyman- and Werner-bands in this spectral region (1150-1700 A) are identified. This spectrum is compared with a laboratory H2 spectrum and with photoabsorption cross sections for CH4 and C2H6. An upper limit to the slant column density of these hydrocarbons above the auroral emissions is found to be approximately 2 x 10 to the 17th/sq cm.

Durrance, S. T.↗