Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ti-6Al-4V”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Model for the Softening Factor within Stages of Work Hardening

A formulation for a dimensionless coefficient c b is derived that represents a scale of microstructural softening for alloys which follow Kocks-Mecking (K-M) work hardening behavior. The variation of the true plastic strain ε p between the proportional limit σ y and the strength σ u at the instability is determined using the Considère criterion. Parameterization of the model is limited to variables expressly measured within tensile experiments. Further development is now made for the softening factor c bi through the individual and sequential stages 3 and 4 of plastic deformation during K-M work hardening Q behavior. Application is shown for tensile test results of Ti-6Al-4V made by different additively manufactured (AM) processes. It is found that the variation in plastic strain as a function of c bi produces a continuous curve representative of the alloy system. The results of data analysis indicate that Θ o3 and c b3 increase, while Θ o4 and c b4 decrease, as the total plastic strain ε p increases. Furthermore, formulations derived for K-M stages 3 and 4 enable the evaluation of other material parameters such as the activation volume ν* for the onset of plastic deformation. This activation volume is found to be near constant, at a ν*-value of 0.353±0.036 nm 3 as computed using a strain-rate sensitivity of strength exponent m of 0.014, irrespective of the AM method used to produce the Ti-6Al-4V alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Recycling of Titanium Scrap by Shear Assisted Processing and Extrusion (ShAPE)

Titanium and its alloys are used in the aviation and automobile industries due to their remarkable strength to weight ratio, but, commonly, machining loss is high with ~90 wt.% of the material being converted to scrap. Recycling post-consumer Ti scrap directly into solid bulk products is a potential solution for repurposing valuable material. Further, reducing or even eliminating fresh Ti sponge during recycling might lead to lower energy and greenhouse gas emissions. In this study, a solid-phase process known as friction extrusion was utilized to recycle Ti-6Al-4V machining chips into solid wires which could be used as feedstock in additive manufacturing. The friction consolidation technique was first used to convert chips with varying degrees of oxygen content into solid billets for its use as feedstock material in subsequent friction extrusion. The extrudates were fabricated above the beta transition temperature, which was achieved by selecting rotation rate and feed rate, to process the billets near 1000°C using a tungsten-lanthana extrusion die. This work presents the first occurrence of friction extruded titanium alloy wires. The effect of friction extrusion on microstructural features, tensile properties, and texture are reported. Overall, the friction extrusion method is capable of recycling Ti-6Al-4V scrap directly into extruded wire.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Understanding Geometry and Microstructure Interactions In LPBF By Linking Lab Scale Studies To Real Part Case Examples

The mechanical properties derived from simple tensile tests are uniquely important in the design and qualification of load bearing metallic components. The tensile properties in standards for wrought metallic materials are generally accessible for design and simulation engineers, but this is not the case for additively manufactured metals. This work investigates the influence of tensile specimen geometry on the mechanical properties of laser powder bed fusion (LPBF) additively manufactured Ti-6Al-4V, particularly in relation to properties measured from specimens excised from an exemplar part. A comprehensive analysis was conducted across various specimen geometries, considering factors such as thermal history, cross-sectional area, shape, and surface roughness. Key findings reveal that sample size, particularly cross-sectional area, significantly affects reported tensile properties, with ASTM E8 flat and round specimens exhibiting differences in elastic modulus (13%), yield strength (17%), ultimate tensile strength (UTS) (14%), and elongation to failure (11%). Additionally, surface roughness was found to have a limited impact on ASTM round geometries, but it becomes critical in thin-walled and small high-throughput samples. The ASTM flat samples closely matched the properties of samples excised from the exemplar part, underscoring the necessity of testing witness samples that accurately represent end-use conditions. Furthermore, mechanical properties of samples built within the stitch zone of the exemplar part demonstrated reduced ductility, highlighting the importance of laser alignment and qualification in multi-laser additive manufacturing processes. Overall, this study emphasizes the need for careful consideration of specimen geometry and testing conditions to ensure accurate reporting of mechanical properties in LPBF Ti-6Al-4V.

36 MATERIALS SCIENCE↗
DOE OSTI2026

INFLUENCE OF SUPPLEMENTARY ARGON GAS SHIELDING ON THE MICROSTRUCTURE AND MECHANICAL BEHAVIOR OF SS316L ADDITIVELY MANUFACTURED BY DIRECTED ENERGY DEPOSITION

The dissolution of atmospheric gases into parts additively manufactured by directed energy deposition (DED) has long been of concern, and stock shielding solutions have usually proven inadequate at fully removing atmospheric gases from weld beads. The objective of this work was to design a new supplementary argon gas shroud for a specific DED printer and evaluate its effect on microstructure and macroscopic properties of SS316L and the potential for printing more reactive metals such as Ti-6Al-4V. This was investigated by printing four SS316L sample blocks, two with and two without the shroud, each printed in two different orientations. These samples were subsequently evaluated with inert gas fusion (IGF), SEM/EDS imaging, and tensile tests. The shroud reduced oxygen content by 0.019-0.031%, and SEM imaging revealed fewer oxide inclusions. A more dramatic reduction of 0.13% oxygen and 0.171% nitrogen was observed by the inert gas fusion of Ti-6Al-4V samples. Overall, the results indicated the shroud was successful at reducing atmospheric gas uptake within the print region and may enable the printing of reactive metal powders in DED systems.

Helvie, Kyle↗
DOE OSTI2023

Localized keyhole pore prediction during laser powder bed fusion via multimodal process monitoring and X-ray radiography

Systematic fault detection and control during laser powder bed fusion (L-PBF) has been a long-standing objective for system manufacturers and researchers in the additive manufacturing (AM) industry. This manuscript investigates a data fusion approach for detection of keyhole porosity formation during laser irradiation of Ti-6Al-4V substrates by concurrent recording of thermally induced optical emission measured using both off-axis and coaxial photodiode sensors, and acoustic emission. Subsurface defect formation was monitored via high-speed synchrotron X-ray imaging at 20,000 frames per second, enabling temporal registration of keyhole pore formation events to the monitoring signals at a resolution of 50 µs. We developed data fusion machine learning (ML) models for localized prediction of keyhole pore formation at various time scales ranging from 0.5 ms to 2 ms. The signal segments were featurized using two independent approaches: (1) power spectral density (PSD) and (2) highly comparative time series analysis (HCTSA) framework. The extracted features from different sensor modalities were fused together to construct a multimodal feature space and sequential feature selection was used to determine the most informative features for training the ML models. The predictive performance was evaluated for three classifying algorithms: Support Vector Machine (SVM), K-Nearest Neighbor (KNN), and Gaussian Naive Bayes (GNB). As a result, pore formation events were predicted with up to 0.95 F1-score, 1.0 recall and 0.94 accuracy. The most heavily weighted features indicate that model performance is chiefly governed by the acoustic monitoring signal, with a secondary contribution from the optical emission sensors.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Additively manufactured β-Ti5553 with laser powder bed fusion: Microstructures and mechanical properties of bulk and lattice parts

Ti5553 (Ti-5Al-5Mo-5V-3Cr wt%) is a titanium alloy widely used for its high strength-to-weight ratio and good formability at elevated temperatures. Unlike Ti-6Al-4V, Ti5553 does not undergo martensitic transformation, preventing cracking of brittle martensite upon rapid cooling. This makes it a strong candidate for additive manufacturing (AM), particularly laser powder bed fusion (L-PBF). L-PBF offers the unique opportunity to make fine lattice structures to reduce component weight. Despite the growing field of AM, there have been limited studies on L-PBF Ti5553 lattices and how their properties differ from the bulk. Here the present work addresses this knowledge gap by investigating microstructures and properties of L-PBF bulk and lattice parts and the effect of post L-PBF heat treatments. Electron microscopy and mechanical testing show that the high dislocation density formed during L-PBF increases bulk part’s yield strength by approximately 100 MPa compared to the conventional alloy. Digital image correlation during compression testing of octet truss lattices reveals a layer-by-layer failure mode. Compared to the bulk, the lattice contains copious ω nanoprecipitation, weaker <001> texture, smaller average grain sizes, and larger content of high-angle grain boundaries. These features elicit differences in Taylor factor distributions for the lattice depending on load direction, underlining challenges in predicting lattice mechanical response based on bulk properties. By examining the processing-structure-property relationships in the bulk and lattice, the present results delineate their microstructural and mechanical differences and establish a benchmark for the future design applications of L-PBF Ti5553.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Active learning using hybrid surrogate tool life modeling for machining process optimization

Here, this paper describes an active learning approach for part-to-part iterative machining process optimization using a hybrid surrogate tool life model. A probabilistic interpolating tool life model is developed by combining the empirical Taylor-type tool life equation and the model fit error. The probabilistic tool life model is then used to calculate the machining cost per part distribution. The optimal machining parameters are selected using an expected improvement in machining cost per part criterion. The method is validated numerically using experimental results; the results show a median convergence error of 2.2% after three tests over 400 simulations. The method is validated experimentally on two industrial applications for Ti-6Al-4V roughing resulting in a cost per part reduction greater than 23% after two tests. The described method is a robust solution for rapid convergence to optimal machining parameters in an industrial production environment.

Active learning↗
DOE OSTI2026

Investigating property-porosity relationships for micro-architected lattice structures

Micro-architected structures are increasingly valued for their light weight and tunable mechanical properties; this class of material includes sheet structures like the Schöen gyroid and beam lattices like the octet. For design purposes, it is critical to understand how to tune the relative density (RD) to obtain desired mechanical properties. This study investigates the mechanical response of Ti-6Al-4V gyroid structures, spanning a broad range of RDs (0.03–0.90), unit cell sizes (1–4 cm), and sheet thicknesses (0.2–7.8 mm). Results demonstrate that the classical Gibson-Ashby power law scaling between RD and modulus and yield stress does not adequately capture the response over a wide range of RDs, nor does it extrapolate correctly to the fully dense solid. Analytical models, in concert with experimental results and high-fidelity finite element calculations, show that the deviation from Gibson-Ashby reflects a transition from structure-dominated to material-dominated behavior. Distinctions are drawn between scaling relationships and property-porosity models, and an analytical model is proposed to better capture the evolution of mechanical properties with RD. These observations are mirrored in other architected topologies, like the octet, and highlight the importance of understanding the relationship between mechanical properties and geometry for design purposes.

Materials science↗
DOE OSTI2023

High frequency beam oscillation keyhole dynamics in laser melting revealed by in-situ x-ray imaging

The metal additive manufacturing industry is actively developing instruments and strategies to enable higher productivity, optimal build quality, and controllable as-built microstructure. A beam controlling technique, laser oscillation has shown potential in all these aspects in laser welding; however, few attempts have been made to understand the underlying physics of the oscillating keyholes/melt pools which are the prerequisites for these strategies to become a useful tool for laser-based additive manufacturing processes. Here, to address this gap, we utilized a synchrotron-based X-ray operando technique to image the dynamic keyhole oscillation in Ti-6Al-4V using a miniature powder bed fusion setup. We found good agreement between the experimental observations and simulations performed with a validated Lattice Boltzmann multiphysics model. The study revealed the continuous and periodic fluctuations in the characteristic keyhole parameters that are unique to the oscillating laser beam processing and responsible for the chevron pattern formation at solidification. In particular, despite the intrinsic longer-range fluctuation, the oscillating technique displayed potential for reducing keyhole instability, mitigating porosity formation, and altering surface topology. These insights on the oscillating keyhole dynamics can be useful for the future development and application of this technique.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dynamic response of additively manufactured Ti–5Al–5V–5Mo–3Cr as a function of heat treatment

Both shock and shockless compression experiments were performed on laser powder bed fusion (LPBF) Ti–5Al–5V–5Mo–3Cr (Ti-5553) to peak compressive stresses near 15 GPa. Experiments were performed on the as-built material, containing a purely β (body centered cubic) microstructure, and two differing heat treatments resulting in a dual phase α (hexagonal close packed) and β microstructure. The Hugoniot, Hugoniot elastic limit (HEL), and spallation strength were measured and compared to wrought Ti-6Al-4V (Ti-64). The results indicate the LPBF Ti-5553 Hugoniot response is similar between heat treatments and to Ti-64. The HEL stress observed in the LPBF Ti-5553 was considerably higher than Ti-64, with the as-built, fully β alloy exhibiting the largest values. The spallation strength of the LPBF Ti-5553 was also similar to Ti-64. Clear evidence of initial porosity serving as initiation sites for spallation damage was observed when comparing computed tomography measurements before and after loading. Post-mortem scanning electron microscopy images of the recovered spallation samples showed no evidence of retained phase changes near the spall plane. The spall plane was found to have kinks aligned with the loading direction near areas with large concentrations of twin-like, crystallographic defects in the as-built condition. For the heat-treated samples, the concentrations of twin-like, crystallographic defects were absent, and no preference for failure at the interface between the α and β phases was observed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Direct mechanistic connection between acoustic signals and melt pool morphology during laser powder bed fusion

Various nondestructive diagnostic techniques have been proposed for in situ process monitoring of laser powder bed fusion (LPBF), including melt pool pyrometry, whole-layer optical imaging, acoustic emission, atomic emission spectroscopy, high speed melt pool imaging, and thermionic emission. Correlations between these in situ monitoring signals and defect formation have been demonstrated with acoustic signals having been shown to predict pore formation with especially high confidence in recent machine learning studies. Here, in this work, time-resolved acoustic data are collected in both the conduction and keyhole welding regimes of LPBF-processed Ti-6Al-4V alloy. A non-dimensionalized Strouhal number analysis, used in whistle aeroacoustics, is applied to demonstrate that the acoustic signals recorded in the keyhole regimes can be directly associated with the vapor depression morphology. This mechanistic understanding developed from whistle aeroacoustics shows that acoustic monitoring during the LPBF process can provide a direct probe into the vapor depression dynamics and defect occurrence, especially in the keyhole regimes relevant to printing and defect formation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Thermal modeling of directed energy deposition additive manufacturing using graph theory

Purpose: The purpose of this paper is to develop, apply and validate a mesh-free graph theory–based approach for rapid thermal modeling of the directed energy deposition (DED) additive manufacturing (AM) process. Design/methodology/approach: Here, the authors develop a novel mesh-free graph theory–based approach to predict the thermal history of the DED process. Subsequently, the authors validated the graph theory predicted temperature trends using experimental temperature data for DED of titanium alloy parts (Ti-6Al-4V). Temperature trends were tracked by embedding thermocouples in the substrate. The DED process was simulated using the graph theory approach, and the thermal history predictions were validated based on the data from the thermocouples. Findings: The temperature trends predicted by the graph theory approach have mean absolute percentage error of approximately 11% and root mean square error of 23°C when compared to the experimental data. Moreover, the graph theory simulation was obtained within 4 min using desktop computing resources, which is less than the build time of 25 min. By comparison, a finite element–based model required 136 min to converge to similar level of error. Research limitations/implications: This study uses data from fixed thermocouples when printing thin-wall DED parts. In the future, the authors will incorporate infrared thermal camera data from large parts. Practical implications: The DED process is particularly valuable for near-net shape manufacturing, repair and remanufacturing applications. However, DED parts are often afflicted with flaws, such as cracking and distortion. In DED, flaw formation is largely governed by the intensity and spatial distribution of heat in the part during the process, often referred to as the thermal history. Accordingly, fast and accurate thermal models to predict the thermal history are necessary to understand and preclude flaw formation. Originality/value: This paper presents a new mesh-free computational thermal modeling approach based on graph theory (network science) and applies it to DED. The approach eschews the tedious and computationally demanding meshing aspect of finite element modeling and allows rapid simulation of the thermal history in additive manufacturing. Although the graph theory has been applied to thermal modeling of laser powder bed fusion (LPBF), there are distinct phenomenological differences between DED and LPBF that necessitate substantial modifications to the graph theory approach.

42 ENGINEERING↗
DOE OSTI2023

Machine learning–aided real-time detection of keyhole pore generation in laser powder bed fusion

Porosity defects are currently a major factor that hinders the widespread adoption of laser-based metal additive manufacturing technologies. One common porosity occurs when an unstable vapor depression zone (keyhole) forms because of excess laser energy input. With simultaneous high-speed synchrotron x-ray imaging and thermal imaging, coupled with multiphysics simulations, we discovered two types of keyhole oscillation in laser powder bed fusion of Ti-6Al-4V. Amplifying this understanding with machine learning, we developed an approach for detecting the stochastic keyhole porosity generation events with submillisecond temporal resolution and near-perfect prediction rate. Finally, the highly accurate data labeling enabled by operando x-ray imaging allowed us to demonstrate a facile and practical way to adopt our approach in commercial systems.

42 ENGINEERING↗
DOE OSTI2022

Evaluation of AddUp Precision L-PBF Technology for Tooling and Other Industrial Applications

ORNL (Contractor) and AddUp Inc. (Participant) collaborated to enable the adoption of laser powder bed fusion for tooling applications, critical for reshoring the manufacturing sector in the U.S. Most of the work on laser powder bed fusion has focused on high value materials such as Ti-6Al-4V and Inconel 718 for niche applications in aerospace, biomedical and energy sectors. In this collaboration, ORNL and AddUp worked laser powder bed fusion of maraging steels for tooling applications while leveraging the unique ability of the AddUp laser powder bed fusion system to deposit fine powders. We demonstrated that the AddUp technology is capable of depositing complex artifacts and features such as overhangs within desired tolerances. We also showed that direct aging of the deposited parts result in simultaneously higher strength and elongation compared to the conventional two step heat treatments, which could result in significant energy savings. Finally, we developed thermos-kinetic models to enable design of heat treatments for optimal material properties compared to the energy intensive empirical methods currently used. The report summarizes the detailed findings of this collaboration.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development of HPC based phase field simulations tool for modification of alloy morphology to enhance material properties during additive manufacturing (AM) process

Currently, additive manufacturing (AM) technology is extensively used to manufacture aerospace components because of the unique advantages of the technique in producing custom designs, complex geometries in a near-net fashion that significantly reduces the manufacturing cost, and improved energy efficiency. However, the thermodynamic properties of existing aerospace alloys and the thermal conditions that prevail in most of the powder-bed based additive manufacturing processes lead to undesirable columnar / columnar-dendritic microstructures that promote solidification cracking during the process, and the development of anisotropy in the mechanical properties of the as-built components. Time consuming, energy-intensive post AM treatments are required to recover the mechanical properties of the wrought components for which the existing alloy compositions were designed for. However, novel alloy compositions, that exploit the AM thermal conditions to produce fine, equiaxed grain structures in the as-built condition, with mechanical properties equal to or exceeding those of the wrought work-horse alloy, Ti-6Al-4V has recently been demonstrated in Ti-Cu alloys. Significant energy savings up to 66% can be obtained for a typical aerospace component through digitally designing the AM process, process parameters, and alloy composition. The current project focused on developing a fundamental understanding of the evolution of the columnar to equiaxed transition (CET) occurring during solidification under AM thermal conditions in Ti-Cu and Ti-Cu-X alloys using high-fidelity phase field (PF) simulations using the leadership class computing facilities that exist in the national laboratories. The simulations were able to capture the effect of alloy and process conditions on CET, and clearly showed the beneficial effect of a ternary solute addition to Ti-Cu binary alloys on CET. The simulations indicated that bulk nucleation in the liquid ahead of the solidifying epitaxial front was promoted by a large, transient, thermal undercooling promoted by the mismatch between the growth rate of the dendrite tips in the epitaxial front and the imposed solidification rate. AM experiments performed at Raytheon Technologies Research Center using the same thermal conditions used in the PF simulations indicated the formation of equiaxed grains, although the grain size was bigger than the ones reported in the literature. On the other hand, the equiaxed grain size predicted by PF simulations were smaller than the grain size of Ti-Cu alloys reported in the literature. The industry will follow up the existing work in a future program that would involve further optimization of the process for the Ti-Cu-X alloys to demonstrate the application of the process and the alloy to a specific aerospace component.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Stress-strain and work hardening relationships of 304L AM alloy

A new approach to analytically derive constitutive stress-strain relationships from modeling the work hardening behavior of alloys was developed for assessing the strength and ductility of the Ti-6Al-4V alloy. This new approach is now successfully applied for assessing the quasi-static stress-strain behavior of an additively manufactured 304L sample. A predictive capability of this modelling approach may then be extended to model material stress-strain behavior at higher strain rates of loading.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Critical feature and seawater testing of cross-flow rotor components fabricated with additive manufacturing

Advanced manufacturing (AM) materials were investigated for their suitability for use in cross-flow turbine rotors. AM materials were categorized into 3 classes – plastics, metals, and ceramics – and reviewed for suitability based on a set of engineering requirements and criteria. Two plastics and two metals were selected to undergo further testing: Essentium CF25, Markforged Onyx, Titanium Ti-6Al-4V, and Inconel 718. Dogbone-shaped specimens were printed from each material in two sets. The first set was tensile tested to get a material baseline. The second set was submerged in the seawater tanks at PNNL-Sequim for 6 months to determine water uptake, corrosion, and biofouling resistance and then subsequently tensile tested. While few macroscopic changes could be observed after seawater testing, the plastic materials degraded significantly as compared to baseline, while the metal material properties remained consistent. Titanium and Inconel are used consistently by industry in extreme conditions, and the materials show promising performance for marine energy use cases.

McVey, James R.↗
DOE OSTI2026

Thermodynamics of Bimetallic Joints between Titanium and Tantalum Produced by Laser Powder Bed Fusion

Laser powder bed fusion (LBPF) is currently the most mature metal additive manufacturing (AM) technology. While it does not have the same flexibility as directed energy deposition techniques to produce compositional gradients, LPBF can still be used to generate bimetallic parts by depositing one metal on a build plate made of another. Here, in this study, we print combinations of Ti-6Al-4V with Ta and characterize defects that occur at the interface. We use thermodynamic modeling to explain the formation of keyhole porosity and solidification cracks when Ta is built on a Ti baseplate, and the lack of defects when the materials are reversed. By understanding the mechanisms that lead to defect formation, the methodology demonstrated here can be applied to other material systems to efficiently design bimetallic LPBF processes.

36 MATERIALS SCIENCE↗