Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thrust Force”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Further Research On Helicopter Tail-Boom Strakes

Two documents discuss results of additional investigations of concept introduced in "Helicopter Tail-Boom Strakes" (LAR-13233). Essence of concept that strake or pair of strakes on side of tail boom facing retreating side of main rotor of helicopter perturbs flow in such way to increase aerodynamic pressure on that side, contributing force to thrust from tail rotor. Because of force, thrust required of tail rotor for yaw control reduced. Important advantage in low-speed flight, especially in sideward flight, in which tail-rotor thrust in absence of strake sometimes insufficient.

Kelley, Henry L.↗
NASA NTRS1990

Laboratory simulation of the rocket motor thrust as a follower force

Ground tests of solid propellant rocket motors have shown that metal-containing propellants produce various amounts of slag (primarily aluminum oxide), which is trapped in the motor case causing a loss of specific impulse. Although not yet definitely established, the presence of a liquid pool of slag also may contribute to nutational instabilities that have been observed with certain spin-stabilized, upper-stage vehicles. Because of the rocket's axial acceleration - absent in the ground tests - estimates of in-flight slag mass have been very uncertain. Yet such estimates are needed to determine the magnitude of the control authority of the systems required for eliminating the instability. A test rig with an eccentrically mounted hemispherical bowl was designed and built that incorporates a follower force that properly aligns the thrust vector along the axis of spin. A program that computes the motion of a point mass in the spinning and precessing bowl was written. Using various rpm, friction factors, and initial starting conditions, plots were generated showing the trace of the point mass around the inside of the fuel tank. The apparatus will be used extensively during the 1990 to 1991 academic year and incorporate future design features such as a variable nutation angle and a film height measuring instrument. Data obtained on the nutational instability characteristics will be used to determine order-of-magnitude estimates of control authority needed to minimize the sloshing effect.

Source record↗
NASA NTRS1972

Analysis of an arched outer-race ball bearing considering centrifugal forces.

Thrust-load analysis of a 150-mm angular contact ball bearing, taking into account centrifugal forces but omitting gyroscopics, elastohydrodynamics, and thermal effects. A Newton-Raphson method of iteration is used to evaluate the radial and axial projection of the distance between the ball center and the outer raceway groove curvature center. Fatigue life of the bearing is evaluated. Results for life, contact loads, and angles are given for a conventional bearing and two arched bearings.

Hamrock, B. J.↗
NASA NTRS2024

MSFC-TVC | TB-03: Derivation of Thrust Vector Control (TVC) Actuator-Force / Gimbal-Torque Transformation Matrix

Thrust vector control (TVC) systems for rocket engine propulsion traditionally use a simple linear relationship to convert between actuator forces and torques about the engine gimbal’s center-of-rotation (COR). As shown in Equation (1), the torque about the gimbal COR is proportional to the applied actuator force and the TVC moment arm (MA)—the perpendicular distance between the TVC actuator’s line-of-action (LOA) and the engine gimbal’s COR. While this fundamental relationship remains valid and accurate in a two-dimensional (2D), one-degree-of-freedom (1-DOF) context—particularly in its non-linear formulation as described in the ER63 Technical Bulletin TB-02 (Derivation of Thrust Vector Control (TVC) Engine-Gimbal / Actuator Moment-Arm Geometry)—it becomes limited when extended to three-dimensional (3D), two-degree-of-freedom (2-DOF) analyses. In 3D, out-of-plane angular displacements can arise, causing the gimbaled engine plane-of-motion to become non-coplanar with the respective actuator plane-of-motion. Such misalignments occur due to the rod-end (RE) and/or tail-stock (TE) mounting geometry of individual TVC actuators. These geometric complexities lead to inaccuracies in calculating engine torques and corresponding actuator forces if only the traditional TVC MA relationship is employed. For higher gimbal angular displacements (e.g., greater than 5 degrees), these inaccuracies become more pronounced, necessitating a more robust mathematical framework. This document presents a comprehensive 3D (2-DOF) derivation of a transformation matrix that accurately converts between gimbaled engine torques and TVC actuator forces. By incorporating the necessary geometric and rotational considerations, this new approach corrects the limitations of the traditional TVC MA method. Subsequent sections compare the newly formulated approach to the traditional method, demonstrating its enhanced accuracy and reliability for a broad range of gimbaled engine conditions.

Thrust Vector Control↗
NASA NTRS1987

Large-scale static investigation of circulation-control-wing concepts applied to upper surface-blowing aircraft

The use of a circulation control to deflect turbofan engine thrust beyond 90 deg. has been proven in full-scale static ground tests of the circulation-control-wing/upper-surface-blowing (CCW/USB) concept. This powered high-lift system employs a circular, blown trailing edge to replace the USB mechanical flaps to entrain engine-exhaust flow, and to obtain both a vertical-thrust component and an augmented circulation lift for short takeoff and landing (STOL) applications. Previous tests (Phase 1), done in 1982, of a basic configuration installed on the Quiet Short Haul Research Aircraft confirmed these CCW/USB systems capabilities. A second phase (Phase 2) of full-scale, static, thrust-deflection investigations has reconfirmed the ability to deflect engine thrust from 40 to 102 deg., depending on thrust level. Five new configurations were evaluated and performance improvements noted for those configurations with larger blown span, fences or favorable engine interactions, smaller slot height, and larger radii with less than 180 deg. of CCW surface arc. In general, a 90 deg. circular arc with a smaller slot height provided the best performance, demonstrating that adequate thrust turning can be produced by a trailing-edge shape which may have minimal cruise-performance penalty. Thrust deflections were achieved at considerably lower blowing momentum than was required for the baseline case of Phase 1. Improved performance and versatility were thus confirmed for the CCW/USB system applied to STOL aircraft, where the potential for developing a non-moving-parts pneumatic thrust deflector to rapidly vary horizontal force from thrust to drag, while maintaining constant vertical force, appears quite promising. The conversion from high-lift to lower-drag cruise mode by merely terminating the blowing provides an effective STOL aircraft system.

Shovlin, M. D.↗
NASA NTRS1993

Experimental performance of a ventral nozzle with pitch and yaw vectoring capability for SSTOVL aircraft

Aircraft with supersonic, short takeoff, and vertical landing capability were proposed to replace some of the current high-performance aircraft. Several of these configurations use a ventral nozzle in the lower fuselage, aft of the center of gravity, for lift or pitch control. Internal vanes canted at 20 deg were added to a swivel-type ventral nozzle and tested at tailpipe-to-ambient pressure ratios up to 5.0 on the Powered Lift Facility at NASA LeRC. The addition of sets of four and seven vanes decreased the discharge coefficient by at least 6 percent and did not affect the thrust coefficient. Side force produced by the nozzle with vanes was 14 percent or more of the vertical force. In addition, this side force caused only a small loss in vertical force in comparison to the nozzle without vanes. The net thrust force was 8 deg from the vertical for four vanes and 10.5 deg for seven.

Esker, Barbara S.↗
NASA NTRS1993

Experimental performance of a ventral nozzle with pitch and yaw vectoring capability for SSTOVL aircraft

Aircraft with supersonic, short takeoff and vertical landing capability have been proposed to replace some of the current high-performance aircraft. Several of these configurations use a ventral nozzle in the lower fuselage, aft of the center of gravity, for lift or pitch control. Internal vanes canted at 20 deg were added to a swivel-type ventral nozzle and tested at tailpipe to ambient pressure ratios up to 5.0 on the Powered Lift Facility at NASA Lewis Research Center. The addition of sets of four or seven vanes decreased the discharge coefficient of the nozzle by at least 6 percent and did not effect the thrust coefficient. Side force produced by the nozzle with vanes was 14 percent or more of the vertical force. In addition, this side force caused only a smalll loss in vertical force in comparison to the nozzle without vanes. The net thrust force was 8 deg from the vertical for four vanes and 10.5 deg for seven.

Esker, Barbara S.↗
NASA NTRS2004

Development and Demonstration of a Device to Determine Thrust by Measuring the Force on a Target Plate in the Exhaust of a Plasma Thruster

A device has been developed to measure the force on a target plate by an impacting beam of charged and neutral particles. This device, an impact thrust stand, was developed to allow thrusters at low TRL, levels to be easily tested without the expense of developing a flight prototype of the thruster to be placed on a conventional thrust stand. The impact thrust stand was developed for the Variable Specific Impulse Magnetoplasma Rocket (VASIMR) but has been tested and calibrated using several devices including Hall thrusters. The calibration and comparison of the impact thrust stand against conventional thrust stands will be discussed in this paper.

Chavers, Greg↗
NASA NTRS1995

Multiaxis Thrust-Vectoring Characteristics of a Model Representative of the F-18 High-Alpha Research Vehicle at Angles of Attack From 0 deg to 70 deg

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the multiaxis thrust-vectoring characteristics of the F-18 High-Alpha Research Vehicle (HARV). A wingtip supported, partially metric, 0.10-scale jet-effects model of an F-18 prototype aircraft was modified with hardware to simulate the thrust-vectoring control system of the HARV. Testing was conducted at free-stream Mach numbers ranging from 0.30 to 0.70, at angles of attack from O' to 70', and at nozzle pressure ratios from 1.0 to approximately 5.0. Results indicate that the thrust-vectoring control system of the HARV can successfully generate multiaxis thrust-vectoring forces and moments. During vectoring, resultant thrust vector angles were always less than the corresponding geometric vane deflection angle and were accompanied by large thrust losses. Significant external flow effects that were dependent on Mach number and angle of attack were noted during vectoring operation. Comparisons of the aerodynamic and propulsive control capabilities of the HARV configuration indicate that substantial gains in controllability are provided by the multiaxis thrust-vectoring control system.

Asbury, Scott C.↗
NASA NTRS1976

Effects of nozzle exit location and shape propulsion-induced aerodynamic characteristics due to vectoring twin nozzles at Mach numbers from 0.40 to 1.2

An investigation was conducted in the Langley 16-foot transonic tunnel to determine the induced lift characteristics of a vectored-thrust concept in which jet-exhaust nozzles were located in the fuselage at or near the wing trailing edge. The effects of moving twin rectangular nozzles rearward from the wing trailing edge and of round nozzles at the trailing edge only were studied at Mach numbers from 0.4 to 1.2, angles of attack up to 14 deg, and thrust coefficients up to 0.35. Nozzle deflection angle varied from 0 deg to 45 deg. Separate force balances were used to determine both total aerodynamic and thrust forces and thrust forces alone which allowed for a direct measurement of jet turning angle at forward speeds. The Reynolds number per meter varied from 8.20 x 1 million to 13.12 x 1 million.

Capone, F. J.↗
NASA NTRS1977

Full-scale altitude engine test of a turbofan exhaust-gas-forced mixer to reduce thrust specific fuel consumption

The specific fuel consumption of a low-bypass-ratio, confluent-flow, turbofan engine was measured with and without a mixer installed. Tests were conducted for flight Mach numbers from 0.3 to 1.4 and altitudes from 10,670 to 14,630 meters (35,000 to 48,000 ft) for core-stream-to-fan-stream temperature ratios of 2.0 and 2.5 and mixing-length-to-diameter ratios of 0.95 and 1.74. For these test conditions, the reduction in specific fuel consumption varied from 2.5 percent to 4.0 percent. Pressure loss measurements as well as temperature and pressure surveys at the mixer inlet, the mixer exit, and the nozzle inlet were made.

Cullom, R. R.↗
NASA NTRS1975

The effects on propulsion-induced aerodynamic forces of vectoring a partial-span rectangular jet at Mach numbers from 0.40 to 1.20

An investigation was conducted in the Langley 16-foot transonic tunnel to determine the induced lift characteristics of a vectored thrust concept in which a rectangular jet exhaust nozzle was located in the fuselage at the wing trailing edge. The effects of nozzle deflection angles of 0 deg to 45 deg were studied at Mach numbers from 0.4 to 1.2, at angles of attack up to 14 deg, and with thrust coefficients up to 0.35. Separate force balances were used to determine total aerodynamic and thrust forces as well as thrust forces which allowed a direct measurement of jet turning angle at forward speeds. Wing pressure loading and flow characteristics using oil flow techniques were also studied.

Capone, F. J.↗
NASA NTRS1984

Shock Mounting for Heavy Machines

Elastomeric bearings eliminate extraneous forces. Rocket thrust transmitted from motor to load cells via support that absorbs extraneous forces so they do not affect accuracy of thrust measurements. Adapter spoked cone fits over forward end of rocket motor. Shock mounting developed for rocket engines under test used as support for heavy machines, bridges, or towers.

Thompson, A. R.↗
NASA NTRS1983

Effects of varying podded nacelle-nozzle installations on transonic aeropropulsive characteristics of a supersonic fighter aircraft

The aeropropulsive characteristics of an advanced twin engine fighter designed for supersonic cruise was investigated in the 16 foot Transonic Tunnel. The performance characteristics of advanced nonaxisymmetric nozzles installed in various nacelle locations, the effects of thrust induced forces on overall aircraft aerodynamics, the trim characteristics, and the thrust reverser performance were evaluated. The major model variables included nozzle power setting; nozzle duct aspect ratio; forward, mid, and aft nacelle axial locations; inboard and outboard underwing nacelle locations; and underwing and overwing nacelle locations. Thrust vectoring exhaust nozzle configurations included a wedge nozzle, a two dimensional convergent divergent nozzle, and a single expansion ramp nozzle, each with deflection angles up to 30 deg. In addition to the nonaxisymmetric nozzles, an axisymmetric nozzle installation was also tested. The use of a canard for trim was also assessed.

Capone, F. J.↗