SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A textile includes: (1) a matrix; and (2) particulate fillers dispersed within the matrix. The textile has a transmittance of infrared radiation at a wavelength of 9.5 μm of at least about 40%, and the textile has a weighted average reflectivity of radiation over a wavelength range of 0.3 μm to 2 μm of at least about 40%.
Carbon fiber reinforced polymer composites are highly desirable for automotive and wind energy applications due to advantages associated with weight reduction, high stiffness and strength, durability, and recyclability. The high cost of carbon fiber has been a limiting factor in its widespread adoption in non-aerospace applications. A low cost (estimated < $11 per kg) wide tow (450-600k) carbon fiber derived from textile grade polyacrylonitirile precursor, and hence called Textile Grade Carbon Fiber (TCF) is introduced in this paper. Fundamental aspects of the TCF are discussed along with a detailed characterization of its mechanical properties. Two manufacturing processes relevant to automotive and wind energy applications are considered, namely-compression molding and resin infusion. Furthermore, at various stages the TCF has been compared to commercial non-aerospace 50k carbon fiber composite. Detailed physical and mechanical properties including tensile, flexural, compression, and interlaminar shear properties are reported and compared to non-aerospace carbon fiber composite. The results provide a means for designers and end-users in the automotive and wind energy sector to consider different forms of economical non-aerospace carbon fibers.
Producing commodity aromatic hydrocarbons from textile waste is a promising approach to promote carbon neutrality and circular economy. Catalytic degradation of flax waste (FW) to generate furans and its subsequent Diels-Alder transformation to monocyclic aromatic hydrocarbons over USY zeolite were conducted. Experimental results indicated that USY catalyzed FW resulted in a 5.5-fold increase in furans production compared with the non-catalytic trial. The Si/Al molar ratio in USY played a determining role in furans formation, and a 5-fold increase was observed over USY with a Si/Al ratio of 5.3 as opposed to that with a Si/Al ratio of 11. Plastic waste, polyethylene (PE), co-fed with FW yielded 1.6 times higher aromatic hydrocarbons than polypropylene (PP). The selectivity to aromatic hydrocarbons reached 81.6% under 20% PE co-fed with 80% FW, in which benzene, toluene, and xylenes (BTX) were predominant products with the maximum selectivity of 68%. Furthermore, this study presents a cleaner approach for value-added resource recovery and sustainable management of textile and plastic waste.
This Technical Collaboration Project focused on packaging large tow (≥ 10 grams/meter) textile carbon fibers, for which currently there is no suitable method. Prior to this project, Oak Ridge National Laboratory (ORNL) used a crude packaging approach to deliver (approximately) 100-meter packages for evaluation by intermediates producers, composites fabricators and other collaborators. That packaging approach was simply a hoop wrap on a standard 75 mm (3 inch) cardboard tube, with paper interleaved between layers and little or no tension control during spooling. While this approach was very effective for initial fiber development and sample fiber and small composite sample evaluation, these packages were inadequate for larger-scale demonstrations and more extensive applications development. The paper-interleaved packages were inconsistent, wasteful, and too small for commercial utilization; they were designed as a quick and simple means to package material for delivery into prototyping operations and were never expected to satisfy industrial requirements for commercial production. This project aimed to develop a commercially relevant approach for packaging large tow textile carbon fibers for robust delivery into downstream commercial intermediates and composites production operations. The development of robust packaging equipment that delivers packages meeting industrial requirements is essential to commercial implementation. In this project, the team identified packaging requirements, created a design, and prototyped a new packaging concept at ORNL’s Carbon Fiber Technology Facility (CFTF) and resulting packages were tested in production of non-crimp fabric (NCF).
There is a significant need to expand material options for SMC that has traditionally used glass fibers for decades. There are several integral issues related to chopping and conveying a range of materials including glass, carbon, basalt, thermoplastic tapes, and recycled fibers. These are in a variety of forms including continuous tows, discontinuous agglomerates such as pyrolyzed carbon fibers that could be used to produce a range of SMC intermediates. Standard/conventional SMC processing is limited to cutting rotors specifically for glass and compounding with thermoset polyesters and some epoxies. The multi-material, multi-format line developed in this project is flexible to enable custom conveying and uses an interchangeable rotor dedicated for specific material types. The overall tasks undertaken in this project included: evaluation of the fiber feed mechanism, effect of textile grade carbon, evaluating servo motor controlling of conveyor, evaluate doctor box resin feed, evaluate compaction unit, evaluation of different formulations, and develop automation such as PLC programming. The new multi-material SMC line Version 2 (SCM-V2) incorporated servo motors over induction motors which gave the overall cutter system precision control and made it quiet. The addition of a 14-roll compaction unit at the end of the line in SMC-V2 enabled higher material wet out which was a limitation in the SMC Version 1 (SMC-V1). The cutters were further updated to reduce the cantilever overhang of the fiber which enabled more uniform cut lengths for glass, carbon, and basalt fibers. The overall instrumentation and system control including a remote control operation was enabled in the SMC-V2. The line speed is capable of 10-20 ft/minute. The cutting modules were designed and engineered for cutting glass, basalt and textile grade carbon in 300k and 450-600k format widths. The cutting trials were established for a range of fiber types. The study also demonstrated the utility of the line to cut and produce basalt fiber SMC. Initial trials were conducted on the properties from recycled carbon fiber (rCF) mats in epoxy resin. Overall, the Covid19 situation constrained the team from accessing the SMC line for over 18 months. Despite this challenge major advancements were made.
The economic viability of high-strength carbon fibers is pivotal for their integration into Type IV compressed hydrogen storage tanks. Oak Ridge National Laboratory is advancing this objective by developing cost-effective, textile-grade polyacrylonitrile (PAN) precursor fibers through an optimized wet spinning-process to garner more microstructural control over the precursor fibers. Here, this study examines the microstructural characteristics of PAN fibers, particularly the crystalline orientation factor, and their impact on mechanical properties in both precursor and thermally converted carbon fibers (CFs). Three wet-spun PAN fibers, all having diameters of 12-13 µm but varying orientation factors were assessed. Comprehensive characterization using X-ray scattering and microscopy revealed that fibers with higher orientation factors exhibited enhanced crystallinity and optimized crystallite sizes. Mechanical testing demonstrated that the PAN fiber with the highest orientation factor achieved the greatest tensile strength (98 ksi) and modulus (1.60 Msi). Additionally optical and scanning electron microscopy confirmed smooth and defect-free surfaces across all samples. These findings indicate that manipulating spinning parameters to maximize orientation factor is more impactful in achieving high strength and modulus over factors attributed to crystallinity and crystallite sizes. Here, highest performing CFs, thermally processed in lab from textile-grade precursor averaged 558 ksi, a 10% increase over previous results.
Textile technology from aerospace research and applicability to textile and apparel industries
Materials, design considerations, and design details for textile mechanical elements used in aerospace vehicle parachute systems are briefly reviewed. Friction burns are noted as a major cause of parachute system failures. The friction burn hazard can be minimized by designing for predeployment and deployment sequence control with textile mechanical restraints. Two basic restraint designs (restraint loops and line ties) are discussed and various applications of the designs shown.
The availability of textile grade ceramic fibers has sparked great interest for applications in composite reinforcement and high temperature insulation. This paper summarizes the properties of various small diameter textile grade ceramic fibers currently available. Room temperature mechanical and electrical properties of the fibers are discussed for three cases: ambient conditions, after heat aging in argon, and after heat aging in wet air. Dow Corning (R) HPZ Ceramic Fiber, a silicon nitride type fiber, is shown to have improved retention of mechanical and electrical properties above 1200 C.
The use of innovative cost effective material forms and processes is being considered for fabrication of future primary aircraft structures. Processes that have been identified as meeting these goals are textile preforms that use resin transfer molding (RTM) and consolidation forming. The Novel Composites for Wing and Fuselage Applications (NCWFA) program has as its objective the integration of innovative design concepts with cost effective fabrication processes to develop damage-tolerant structures that can perform at a design ultimate strain level of 6000 micro-inch/inch. In this on-going effort, design trade studies were conducted to arrive at advanced wing designs that integrate new material forms with innovative structural concepts and cost effective fabrication methods. The focus has been on minimizing part count (mechanical fasteners, clips, number of stiffeners, etc.), by using cost effective textile reinforcement concepts that provide improved damage tolerance and out-of-plane load capability, low-cost resin transfer molding processing, and thermoplastic forming concepts. The fabrication of representative Y spars by consolidation methods will be described. The Y spars were fabricated using AS4 (6K)/PEEK 150g commingled angle interlock 0/90-degree woven preforms with +45-degree commingled plies stitched using high strength Toray carbon thread and processed by autoclave consolidation.
Flexural stiffness properties of a textile composite beam are obtained from a finite-element model of the unit cell. Three linearly independent deformations, namely, pure extension, pure bending and pure shear, are applied to the unit cell. The top and bottom surfaces of the beam are assumed to be traction free. Periodic boundary conditions on the lateral boundaries of the unit cell are enforced by multi-point constraint elements. From the forces acting on the unit cell, the flexural stiffness coefficients of the composite beam are obtained. The difficulties in determining the transverse shear stiffness are discussed, and a modified approach is presented. The methods are first verified by applying them to isotropic and bimaterial beams for which the results are known, and then illustrated for a simple plain-weave textile composite.
This project has the objective of exploring the use of graphite fiber textile preform/copper matrix composites in spacecraft heat transmitting and radiating components. The preforms are to be fabricated by braiding of tows and when infiltrated with copper will result in a 3-D reinforced, near net shape composite with improved specific properties such as lower density and higher stiffness. It is anticipated that the use of textile technology will result in a more robust preform and consequently better final composite; it is hard to anticipate what performance tradeoffs will result, and these will be explored through testing and characterization.
A glossary was developed to define textile terminology applicable to the manufacture of composites. Terms describing fabric structure were illustrated for clarity. Descriptive terms for defects from both textile and composites industry were included.
Three-dimensional (3D) woven preforms are currently being considered for use as primary structural components. Lack of technology to properly manufacture, characterize and predict mechanical properties, and predict damage mechanisms leading to failure are problems facing designers of textile composite materials. Two material systems with identical specifications but different manufacturing approaches are investigated. One manufacturing approach resulted in an irregular (nonuniform) preform geometry. The other approach yielded the expected preform geometry (uniform). The objectives are to compare the mechanical properties of the uniform and nonuniform angle interlock 3D weave constructions. The effect of adding layers of laminated tape to the outer surfaces of the textile preform is also examined. Damage mechanisms are investigated and test methods are evaluated.
One of the greatest difficulties in developing detailed models of the mechanical response of textile reinforced composites is an accurate model of the reinforcing elements. In the case of elastic property prediction, the variation of fiber position may not have a critical role in performance. However, when considering highly localized stress events, such as those associated with cracks and holes, the exact position of the reinforcement probably dominates the failure mode. Models were developed for idealized reinforcements which provide an insight into the local behavior. However, even casual observations of micrographical images reveals that the actual material deviates strongly from the idealized models. Some of the deviations and causes are presented for triaxially braided and three dimensionally woven textile composites. The necessary modeling steps to accommodate these variations are presented with some examples. Some of the ramifications of not accounting for these discrepencies are also addressed.
A probabilistic model utilizing random material characteristics to predict damage evolution in textile laminates is presented. Model is based on a division of each ply into two sublaminas consisting of cells. The probability of cell failure is calculated using stochastic function theory and maximal strain failure criterion. Three modes of failure, i.e. fiber breakage, matrix failure in transverse direction, as well as matrix or interface shear cracking, are taken into account. Computed failure probabilities are utilized in reducing cell stiffness based on the mesovolume concept. A numerical algorithm is developed predicting the damage evolution and deformation history of textile laminates. Effect of scatter of fiber orientation on cell properties is discussed. Weave influence on damage accumulation is illustrated with the help of an example of a Kevlar/epoxy laminate.
NASA's Advanced Composite Technology (ACT) Program was initiated in 1990 with the purpose of developing less costly composite aircraft structures. A number of innovative materials and processes were evaluated as a part of this effort. Chief among them are composite materials reinforced with textile preforms. These new forms of composite materials bring with them potential testing problems. Methods currently in practice were developed over the years for composite materials made from prepreg tape or simple 2-D woven fabrics. A wide variety of 2-D and 3-D braided, woven, stitched, and knit preforms were suggested for application in the ACT program. The applicability of existing test methods to the wide range of emerging materials bears investigation. The overriding concern is that the values measured are accurate representations of the true material response. The ultimate objective of this work is to establish a set of test methods to evaluate the textile composites developed for the ACT Program.
Various test methods commonly used for measuring properties of tape laminate composites were evaluated to determine their suitability for the testing of textile composites. Three different types of textile composites were utilized in this investigation: two-dimensional (2-D) triaxial braids, stitched uniweave fabric, and three-dimensional (3-D) interlock woven fabric. Four 2-D braid architectures, five stitched laminates, and six 3-D woven architectures were tested. All preforms used AS4 fibers and were resin-transfer-molded with Shell RSL-1895 epoxy resin. Ten categories of material properties were investigated: tension, open-hole tension, compression, open-hole compression, in-plane shear, filled-hole tension, bolt bearing, interlaminar tension, interlaminar shear, and interlaminar fracture toughness. Different test methods and specimen sizes were considered for each category of test. Strength and stiffness properties obtained with each of these methods are documented in this report for all the material systems mentioned above.