Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Temperature checks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Water survey of Canada: Application for use of ERTS-A for retransmission of water resources data

The author has identified the following significant results. Water resources data including water level, water velocity, precipitation, air temperature, ice-out indicator, data collection platform battery check and water stage recorder clock operation have been transmitted from remote areas in Canada using the ERTS Data Collection System. The system has met all requirements. The suitability of satellite retransmission has been demonstrated. The present network will be expanded to 28 in 1975.

Halliday, R. A.↗

Computing Temperatures In Optically Pumped Laser Rods

Computer program presents new model solving temperature-distribution problem for laser rods of finite length and calculates both radial and axial components of temperature distributions in these rods. Contains several self-checking schemes to prevent over-writing of memory blocks and to provide simple tracing of information in case of trouble. Written in Microsoft FORTRAN 77.

Farrukh, Usamah O.↗

Correcting horsepower measurements to a standard temperature

This report discusses the relation between the temperature of the air at the entrance to the carburetor and the power developed by the engine. Its scope is limited to a consideration of the range of temperatures likely to result from changes of season, locality, or altitude, since its primary aim is the finding of a satisfactory basis for correcting power measurements to a standard temperature. The tests upon which this report is based were made upon aviation engines in the Altitude Laboratory of the Bureau of Standards. From the results of over 1,600 tests it is concluded that if calculations be based on the assumption that the indicated horsepower of an engine varies inversely as the square root of the absolute temperature of the carburetor air the values obtained will check closely experimental measurements. The extent to which this relationship would be expected from theoretical considerations is discussed and some suggestions are given relative to the use of this relationship in correcting horsepower measurements. (author)

Sparrow, Stanwood W↗

Formation, early evolution, and gravitational stability of protoplanetary disks

The formation, viscous evolution, and gravitational stability of protoplanetary disks are investigated. The formation process is parameterized by the angular velocity of the molecular cloud core omega, while the viscous evolution is parameterized by the viscosity parameter alpha in the disk; in this study we consider a range of (0.4-6) x 10(exp -14)/s for omega and from 10(exp -5) to 10(exp -1) for alpha. The axisymmetric gravitational stabilities of the disks are checked using Toomre's criterion. The resulting disk surface temperature distribution, (d log T(sub s)/d log R) approximately = -0.6 (R is the cylindrical radius), can be attributed to two heating sources: the viscous heating dominant in the inner disk region, and the accretion shock heating dominant in the outer disk region. This surface temperature distribution matches that observed in many disks around young stellar objects. During the infall stage, disks with alpha less than 10(exp -1.5) become gravitationally unstable independent of omega. The gravitational instabilities occur at radii ranging from 5 to 40 AU. The ratio of the disk mass to the central star mass ranges from 0.2 to 0.5 at the times of instability, about 4 x 10(exp -5) x (omega/10(exp -14)/s)(exp -0.67) yr. Most disks with low alpha and high omega become gravitationally unstable during their formation phase.

Nakamoto, Taishi↗

Comparison of Theoretically and Experimentally Determined Effects of Oxide Coatings Supplied by Fuel Additives on Uncooled Turbine-blade Temperature During Transient Turbojet-engine Operation

An analysis was made to permit the calculation of the effectiveness of oxide coatings in retarding the transient heat flow into turbine blades when the combustion gas temperature of a turbojet engine is suddenly changed. The analysis is checked with experimental data obtained from a turbojet engine whose blades were coated with two different coating materials (silicon dioxide and boric oxide) by adding silicone oil and tributyl borate to the engine fuel. The very thin coatings (approximately 0.001 in.) that formed on the blades produced a negligible effect on the turbine-blade transient temperature response. With the analysis discussed here, it was possible to predict the turbine rotor-blade temperature response with a maximum error of 40 F.

PROTECTIVE COATINGS↗

Five-Year Wilkinson Microwave Anisotropy Probe (WMAP) Observations: Likelihoods and Parameters from the WMAP Data

The Wilkinson Microwave Anisotropy Probe (WMAP), launched in 2001, has mapped out the Cosmic Microwave Background with unprecedented accuracy over the whole sky. Its observations have led to the establishment of a simple concordance cosmological model for the contents and evolution of the universe, consistent with virtually all other astronomical measurements. The WMAP first-year and three-year data have allowed us to place strong constraints on the parameters describing the ACDM model. a flat universe filled with baryons, cold dark matter, neutrinos. and a cosmological constant. with initial fluctuations described by nearly scale-invariant power law fluctuations, as well as placing limits on extensions to this simple model (Spergel et al. 2003. 2007). With all-sky measurements of the polarization anisotropy (Kogut et al. 2003; Page et al. 2007), two orders of magnitude smaller than the intensity fluctuations. WMAP has not only given us an additional picture of the universe as it transitioned from ionized to neutral at redshift z approx.1100. but also an observation of the later reionization of the universe by the first stars. In this paper we present cosmological constraints from WMAP alone. for both the ACDM model and a set of possible extensions. We also consider tlle consistency of WMAP constraints with other recent astronomical observations. This is one of seven five-year WMAP papers. Hinshaw et al. (2008) describe the data processing and basic results. Hill et al. (2008) present new beam models arid window functions, Gold et al. (2008) describe the emission from Galactic foregrounds, and Wright et al. (2008) the emission from extra-Galactic point sources. The angular power spectra are described in Nolta et al. (2008), and Komatsu et al. (2008) present and interpret cosmological constraints based on combining WMAP with other data. WMAP observations are used to produce full-sky maps of the CMB in five frequency bands centered at 23, 33, 41, 61, and 94 GHz (Hinshaw et al. 2008). With five years of data, we are now able to place better limits on the ACDM model. as well as to move beyond it to test the composition of the universe. details of reionization. sub-dominant components, characteristics of inflation, and primordial fluctuations. We have more than doubled the amount of polarized data used for cosmological analysis. allowing a better measure of the large-scale E-mode signal (Nolta et al. 2008). To this end we describe an alternative way to remove Galactic foregrounds from low resolution polarization maps in which Galactic emission is marginalized over, providing a cross-check of our results. With longer integration we also better probe the second and third acoustic peaks in the temperature angular power spectrum, and have many more year-to-year difference maps available for cross-checking systematic effects (Hinshaw et al. 2008).

Dunkey, J.↗

Comparison and calibration of NCAR electra instruments: July 5 and 7, 1987

Measurements of temperature, water vapor, cloud liquid water, and lidar cloud height taken by the National Center for Aeronautical Research (NCAR) Electra are analyzed for two days of the First ISCCP Regional Experiment (FIRE) stratocumulus field program. Examination of instrument time series, correlations between sensors, soundings through the layer, and lidar measurements of cloud base height are used to correct sensor offset problems, check for probe wetting, and choose the most accurate measurements of temperature, humidity, and cloud liquid water.

Austin, Philip H.↗

Investigation of High-Performance Fuels in Multicylinder and in Single-Cylinder Engines at High and Cruising Engine Speeds

An investigation was conducted to compare the knock-limited performance of a 20-percent triptane blend in 28-K fuel with that of 28-R and 33-R fuels at high engine speeds, cruising speeds, and two compression ratios in an K-1830-94 multicylinder engine, Data were obtained with the standard compression ratio of 6.7 and with a compression ratio of 3.0, The three fuels were investigated at engine speeds of 1800, 2250, 2600, and 2800 rpm at high and low blower ratios. A carburetor-air temperature of approximate1y 100 deg F was maintained for the multicylinder-engine runs, Data were obtained on a single R-1830-94 cylinder engine as a means of checking the multicylinder data at the higher speeds. A satisfactory correlation between average mixture temperature and knock-limited manifold pressure was obtained by plotting knock-limited manifold pressure against average mixture temperature for the whole range of engine speeds at constant carburetor air temperature and cylinder-head temperature. The single-cylinder knock-limited performance based on charge-air flow matched that of the multicylinder engine within 6 percent under all the conditions except for 28-R fuel at 2800 rpm; these curves differed from each other by 11 percent in the rich region. The knock rating of 33-R fuel was found to be a little higher than that of the 20-percent triptane blend and 26-R fuel at high mixture temperatures (above 210 deg F) and lean mixtures. The 33-R fuel exhibited rich knock limits appreciably lower than the 20-percent triptane blend, Increasing the compression ratio from 6.7 to 8.0 lowered the knock-limited manifold pressure for all fuels approximately 15 to 18 inches of mercury absolute in the cruising range and 20 to 28 inches of mercury absolute at higher engine speeds. Brake specific fuel consumption was reduced 7 to 9 percent by the increase in compression ratio from 6.7 to 8,0,

Bell, Arthur H.↗

Plasma state in a coaxial accelerator.

Electron temperature and density distributions for helium plasma produced in coaxial accelerator measured spectroscopically, checking thermal equilibrium assumption

PLASMA DENSITY↗

Neutral-particle wake method for measuring the atmospheric temperature from a satellite.

Description of a method that would permit a satellite-borne neutral mass spectrometer to measure the atmospheric temperature. The spectrometer examines the partial pressure variations that occur as the wake of a small rectangular baffle is swept across the entrance orifice of the spectrometer. For a given baffle size and for a mounting distance from the orifice, the depth of the resulting pressure minimum depends only on the thermal velocity or temperature of the observed species. The validity of the method can be checked by measuring the wake characteristics of more than one species and/or by employing each of several baffle sizes. The theory includes the effect of a finite orifice size, finite baffle length, and the backscattering of particles from the baffle into the orifice. It is found that a suitable baffle arrangement can be achieved that will permit the temperature to be measured over at least the range normally encountered in the thermosphere (200 to 2000 K) and, depending on the sensitivity and background pressure of the spectrometer, over an altitude range of about 140 to 600 km.

Brace, L. H.↗

Numerical analysis of flow and heat transfer in the VAFB LOX storage Dewar tank

The present report describes numerical simulation of three-dimensional transient distributions of velocity and temperature of liquid oxygen (LOX) in the LOX Dewar tank of Vendenberg Air Force Base (VAFB). The present analyses cover the replenish time period only. Four test cases have been considered. For all four cases, the input boundary conditions are comprised of LOX facility heat loads, drain flow rates, recirculation flow rates and dewar heating. All the quantities are prescribed as functions of time. The first two test cases considered sensitivity of results to the computational grid. In Case 3, system heat load was changed, while in Case 4, a lower LOX level was specified. Cases 1 and 2 showed that the temperatures were not sensitive to the grid refinement. This provided a basic check on the numerical model. Cases 3 and 4 showed that the thermal boundary layer motion near the tank surface becomes more significant at the late time, e.g., 5 1/2 hours from replenish start. Comparison between results of Cases 3 and 4 showed, as expected, that the smaller initial LOX volume given in Case 4, results in higher temperature level. All calculated velocity and temperature distributions were found to be plausible.

Tam, L. T.↗

Low leak rate poppet-and-seat check valve

Valve leakage due to contaminant entrapment and chattering is effectively minimized by a metallic poppet-and-seat check valve designed for use in extreme environmental and fluid temperature conditions.

Whitten, D. E.↗

Heat transfer and fluid flow in floating-zone crystal growth with a mostly covered melt surface

Computer simulation was conducted to study a modified floating-zone crystal growth process, in which the melt surface is mostly covered with a heated ring. The growth of 6-mm diameter single crystals of NaNO3 was considered, and the effects of the following parameters were studied: (1) temperature of the ring, (2) growth rate, (3) surface tension-temperature coefficient of the melt, (4) thermal expansion coefficient of the melt, and (5) gravity. It was demonstrated that thermocapillary convection in the melt zone is reduced significantly in this modified process. The model was checked against the measured lengths of the meniscus near the growth front and axial temperature distribution in a growing crystal, and the agreement was good.

Lan, C. W.↗

MSL Telecom Automated Anomaly Detection

The Mars Science Laboratory (MSL) Telecom Operations Team at the Jet Propulsion Laboratory (JPL) has implemented a machine learning system in order to automate the anomaly detection process as a part of daily operations. Machine learning enables reliable detection of anomalies in Telecom-related telemetry and automated reporting of Telecom subsystem status, resulting in an 90% reduction in team workload and improved anomaly detection reliability. At present, machine learning methods are used to detect: 1. Anomalous long-term trends in telemetry data 2. Anomalous time-domain evolution of telemetry values Both types of anomalies pose their own unique challenges that are addressed in different ways. In the first case, long term trending of daily minima, maximum, and mean telemetry values in temperatures, currents, voltages, and radio frequency (RF) power levels is used in addition to hard threshold safety checks to look for changes in long-term equipment health and performance. Long-term trending methods allow for ordinary seasonal variations in these quantities caused by temperature changes over the course of the Martian year while allowing operators to determine whether current performance remains in line with historical values from previous years. Changes in long-term trends can provide important insights into the health and status of the rover's on-board systems as well as valuable early warning if subtle degradation begins to take hold. But while trending of daily statistics is valuable, it does not detect anomalies in the short-term time evolution of data over the course of minutes or hours during a day, and this task is handled with short-term shape analysis. Principal components analysis (PCA) has been found to provide robust detection of short-term anomalies, and several examples of the use of PCA to detect actual anomalous events will be provided here. In using PCA, we use both the percentage of explained variance and also a log likelihood test on the PCA expansion coefficients to flag telemetry data for human review. Previous work in the field of spacecraft anomaly detection includes [1] for MSL and [2] for some other JPL missions.

Mukai, Ryan↗

Development of techniques and associated instrumentation for high temperature emissivity measurements

Studies were made to develop a test apparatus for the measurement of total emittance of materials under repeated exposure to simulated earth entry conditions. As no existing test facility met the emittance measurement and entry simulation goals, a new apparatus was designed, fabricated and checked out. This apparatus has the capability of performing total and spectral emittance measurements during cyclic temperature and pressure exposure under sonic and supersonic flow conditions. Emittance measurements were performed on a series of oxidized superalloys, silicide coated columbium alloys and ceramic coatings.

Cunnington, G. R.↗

Segregation effects during solidification in weightless melts

The generalized problem of determining the temperature and solute concentration profiles during directional solidification of binary alloys with surface evaporation was mathematically formulated. Realistic initial and boundary conditions were defined, and a computer program was developed and checked out. The programs computes the positions of two moving boundaries, evaporation and solidification, and their velocities. Temperature and solute concentration profiles in the semiinfinite material body at selected instances of time are also computed.

Li, C.↗

Oso 7 measurements of atomic oxygen and molecular nitrogen densities in the earth's upper atmosphere

Densities of molecular nitrogen and monatomic oxygen are presented as a function of altitude for selected intervals of March-May 1972 Oso 7 satellite data. Results on atmospheric attenuation of solar extreme UV radiation at 200-400 A, at heights from 250 to 500 km, are of particular interest. Satellite sunrise measurements above 330 km are not consistent with the Jacchia (1971) atmospheric model, and may constitute evidence for dynamic phenomena occurring in the heated upper levels. Density and temperature variations are considered mainly responsible for the sunrise anomaly observed. Checks were made for possible errors in the satellite pointing system and other instrumental effects.

Modali, S. B.↗