Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “THERMOPLASTICITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

An approach towards tailoring interfacial structures and properties of multiphase renewable thermoplastics from lignin–nitrile rubber

Lignin-derived thermoplastics and elastomers with both versatile performance and commercialization potential have been an elusive pursuit for the past several decades. Lignin content has been limited to about 30 wt %, often requiring chemical modification, solvent fractionation of lignin, or prohibitively expensive additives. Each of these factors is a deterrent to industrial adoption of lignin-based polymers, limiting the potential of this renewable resource. Herein we describe high-performance multiphase thermoplastics made with a blend of 41 wt % unmodified industrial lignin and low-cost additives in a matrix of general-purpose acrylonitrile-butadiene rubber (NBR). Hardwood soda lignin (HSL) and softwood kraft lignin (SKL) were blended under high shear conditions with NBR, carbon black (CB), polyethylene oxide (PEO), boric acid (BA), and dicumyl peroxide (DCP). This combination with SKL lignin in the proper proportions resulted in a thermoplastic with a tensile strength and failure strain of 25.2 MPa and 9 %, respectively; it exhibited an unexpected tensile yield, similar to that of ABS, a commodity thermoplastic. The analogous HSL lignin compositions are tough materials with tensile strengths of 7.3 16.7 MPa and failure strain of 80 140 %. The contrasting ductility and yield stress behavior were analyzed based on the compositions morphology and interfacial structure arising from the nature of each lignin studied. Lastly, the roles of CB as a reinforcement in the rubbery phase, DCP and BA as cross-linkers to create multiphase networks, and PEO to promote the adhesion and compatibility of lignin in commercial-grade NBR are also discussed in detail.

36 MATERIALS SCIENCE↗

Interlaminar fracture toughness of thermoplastic composites

Edge delamination tension and double cantilever beam tests were used to characterize the interlaminar fracture toughness of continuous graphite-fiber composites made from experimental thermoplastic polyimides and a model thermoplastic. Residual thermal stresses, known to be significant in materials processed at high temperatures, were included in the edge delamination calculations. In the model thermoplastic system (polycarbonate matrix), surface properties of the graphite fiber were shown to be significant. Critical strain energy release rates for two different fibers having similar nominal tensile properties differed by 30 to 60 percent. The reason for the difference is not clear. Interlaminar toughness values for the thermoplastic polyimide composites (LARC-TPI and polyimidesulfone) were 3 to 4 in-lb/sq in. Scanning electron micrographs of the EDT fracture surfaces suggest poor fiber/matrix bonding. Residual thermal stresses account for up to 32 percent of the strain energy release in composites made from these high-temperature resins.

Hinkley, J. A.↗

A dual plate thermoplastic recording device for holographic interferometry

The development of a dual plate holographic interferometer using thermoplastic recording devices is described. The operational characteristics of the thermoplastic devices are investigated and optimized for fringe contrast and signal-to-noise ratio. The dual plate device was demonstrated in a transonic wind tunnel at NASA Ames Research Center. The interferograms derived from the thermoplastic device are compared with those derived from conventional photographic emulsions. The fringe contrast achieved with the optimized thermoplastic device is equivalent to the contrast achieved with conventional techniques.

Umstatter, Holly L.↗

A micrographic study of bending failure in five thermoplastic-carbon fibre composite laminates

The local deformation and failure sequences of five thermoplastic matrix composites were microscopically observed while bending the samples in a small fixture attached to a microscope stage. The thermoplastics are polycarbonate, polysulfane, polyphenylsulfide, polyethersulfane, and polyetheretherketone. Comparison was made to an epoxy matrix composite, 5208/T-300. Laminates tested are (0/90) sub 2S, with outer ply fibers parallel to the beam axis. Four point bending was used at a typical span-to-thickness ratio of 39:1. It was found that all of the thermoplastic composites failed by abrupt longitudinal compression buckling of the outer ply. Very little precursory damage was observed. Micrographs reveal typical fiber kinking associated with longitudinal compression failure. Curved fracture surfaces on the fibers suggest they failed in bending rather than direct compression. Delamination was suppressed in the thermoplastic composites, and the delamination that did occur was found to be the result of compression buckling, rather than vice-versa. Microbuckling also caused other subsequent damage such as ply splitting, transverse ply shear failure, fiber tensile failure, and transverse ply cracking.

Yurgartis, S. W.↗

Interlaminar fracture toughness of thermoplastic composites

Edge delamination tension and double cantilever beam tests were used to characterize the interlaminar fracture toughness of continuous graphite-fiber composites made from experimental thermoplastic polyimides and a model thermoplastic. Residual thermal stresses, known to be significant in materials processed at high temperatures, were included in the edge delamination calculations. In the model thermoplastic system (polycarbonate matrix), surface properties of the graphite fiber were shown to be significant. Cricital strain energy release rates for two different fibers having similar nominal tensile properties differed by 30 to 60 percent. The reason for the difference is not clear. Interlaminar toughness values for the thermoplastic polyimide composites (LARC-TPI and polyimidesulfone) were 3 to 4 in-lb/sq in. Scanning electron micrographs of the EDT fracture surfaces suggest poor fiber/matrix bonding. Residual thermal stresses account for up to 32 percent of the strain energy release in composites made from these high-temperature resins.

Hinkley, Jeffrey A.↗

Ultrasonic Attenuation Results of Thermoplastic Resin Composites Undergoing Thermal and Fatigue Loading

As part of an effort to obtain the required information about new composites for aviation use, materials and NDE researchers at NASA are jointly performing mechanical and NDE measurements on new composite materials. The materials testing laboratory at NASA is equipped with environmental chambers mounted on load frames that can expose composite materials to thermal and loading cycles representative of flight protocols. Applying both temperature and load simultaneously will help to highlight temperature and load interactions during the aging of these composite materials. This report highlights our initial ultrasonic attenuation results from thermoplastic composite samples that have undergone over 4000 flight cycles to date. Ultrasonic attenuation measurements are a standard method used to assess the effects of material degradation. Recently, researchers have shown that they could obtain adequate contrast in the evaluation of thermal degradation in thermoplastic composites by using frequencies of ultrasound on the order of 24 MHz. In this study, we address the relationship of attenuation measured at lower frequencies in thermoplastic composites undergoing both thermal and mechanical loading. We also compare these thermoplastic results with some data from thermoset composites undergoing similar protocols. The composite s attenuation is reported as the slope of attenuation with respect to frequency, defined as b = Da(f)/Df. The slope of attenuation is an attractive parameter since it is quantitative, yet does not require interface corrections like conventional quantitative attenuation measurements. This latter feature is a consequence of the assumption that interface correction terms are frequency independent. Uncertainty in those correction terms can compromise the value of conventional quantitative attenuation data. Furthermore, the slope of the attenuation more directly utilizes the bandwidth information and in addition, the bandwidth can be adjusted in the post processing stage to compensate for the loss of dynamic range of the signal as the composites age.

Madaras, Eric I.↗

Thermoplastic Aircraft Manufacturing Model

A manufacturing process to produce 80 single aisle sized thermoplastic composite aircraft a month is presented. Within the Hi-Rate Composite Aircraft Manufacturing (HiCAM) program a baseline aircraft fuselage was designed and modeled based on the Boeing 787 one-piece barrel build, but scaled down to a single aisle aircraft. Key Performance Parameters (KPPs) of recurring cost, non-recurring cost, and weight are calculated from the model. The outcome of this simulation indicated a prohibitively high non-recurring cost, so the thermoplastic team modeled the manufacturing flow for a panelized fuselage concept. The minimum success criteria is a 30% cost reduction and less than two percent increase in weight compared to the baseline aircraft. Automated Fiber Placement (AFP) is used to layup skins, stamp forming is used to make body frames, stringers, and passenger door surround parts. In the model, Co-Fusion was used to consolidate the skin while simultaneously welding on stringers to make stiffened panels. Additional welding technologies were considered to minimize fastener use and a vertical build concept was used for final assembly to reduce factory size. This manufacturing concept for a thermoplastic aircraft indicated a 39% cost and 12% weight savings compared to the baseline. Additional trade studies were conducted using Northrop Grumman’s Automated Stiffener Forming technology to make stringers and stamp forming instead of AFP to make skins.

thermoplastic composites↗

Thermoplastic Composite Aircraft Manufacturing Model

A manufacturing process to produce 80 single aisle sized thermoplastic composite aircraft a month is presented. Within the Hi-Rate Composite Aircraft Manufacturing (HiCAM) program a baseline aircraft fuselage was designed and modeled based on the Boeing 787 one-piece barrel build, but scaled down to a single aisle aircraft. Key Performance Parameters (KPPs) of recurring cost, non-recurring cost, and weight are calculated from the model. The outcome of this simulation indicated a prohibitively high non-recurring cost, so the thermoplastic team modeled the manufacturing flow for a panelized fuselage concept. The minimum success criteria is a 30% cost reduction and less than two percent increase in weight compared to the baseline aircraft. Automated Fiber Placement (AFP) is used to layup skins, stamp forming is used to make body frames, stringers, and passenger door surround parts. In the model, Co-Fusion was used to consolidate the skin while simultaneously welding on stringers to make stiffened panels. Additional welding technologies were considered to minimize fastener use and a vertical build concept was used for final assembly to reduce factory size. This manufacturing concept for a thermoplastic aircraft indicated a 39% cost and 12% weight savings compared to the baseline. Additional trade studies were conducted using Northrop Grumman’s Automated Stiffener Forming technology to make stringers and stamp forming instead of AFP to make skins.

thermoplastic composites↗

From Petroleum to Biobased Crude: A Thermoplastic Polyurethane from Lignin-Oil Without Isocyanates

The movement to transfer from petroleum-based products and materials to renewables does not necessarily have to bypass the use of oil. A new type of "black-gold" is readily abundant from the earth's most abundant source of aromatic carbon: lignin. While fractionation of petroleum yields fuels and chemicals for a diverse set of industries, lignin fractionation using targeted catalysts has demonstrated the ability to generate monomers and oligomers rich in functional groups for polymer synthesis. This study explores the use of lignin-oil, generated from reductive catalytic fractionation of popular wood, to a hydroxyl-rich mixture of aromatics that is used to synthesize a thermoplastic non-isocyanate polyurethane. The lignin-oil is first converted to a cyclocarbonated derivative using a benign synthetic sequence and further polymerized with a diamine to yield the non-isocyanate TPU. While more work is underway to optimize the reaction conditions and meet typical mechanical properties of commercial materials, initial analysis shows thermoplastic behavior and flexible properties consistent with traditional thermoplastic polyurethanes.

BIOMASS FUELS↗

Multi angle laser light scattering evaluation of field exposed thermoplastic photovoltaic encapsulant materials

Abstract As creep of polymeric materials is potentially a safety concern for photovoltaic modules, the potential for module creep has become a significant topic of discussion in the development of IEC 61730 and IEC 61215. To investigate the possibility of creep, modules were constructed, using several thermoplastic encapsulant materials, into thin‐film mock modules and deployed in Mesa, Arizona. The materials examined included poly(ethylene)‐co‐vinyl acetate (EVA, including formulations both cross‐linked and with no curing agent), polyethylene/polyoctene copolymer (PO), poly(dimethylsiloxane) (PDMS), polyvinyl butyral (PVB), and thermoplastic polyurethane (TPU). The absence of creep in this experiment is attributable to several factors of which the most notable one was the unexpected cross‐linking of an EVA formulation without a cross‐linking agent. It was also found that some materials experienced both chain scission and cross‐linking reactions, sometimes with a significant dependence on location within a module. The TPU and EVA samples were found to degrade with cross‐linking reactions dominating over chain scission. In contrast, the PO materials degraded with chain scission dominating over cross‐linking reactions. Although we found no significant indications that viscous creep is likely to occur in fielded modules capable of passing the qualification tests, we note that one should consider how a polymer degrades, chain scission or cross‐linking, in assessing the suitability of a thermoplastic polymer in terrestrial photovoltaic applications.

14 SOLAR ENERGY↗

Properties and Biodegradation of Thermoplastic Starch Obtained from Grafted Starches with Poly(lactic acid)

Properties and biodegradation of thermoplastic starch obtained using granular starches grafted with poly(lactic acid) (St-g-PLA) were studied. The grafting of PLA on the starch granule was verified by the emergence of the carbonyl group in the FTIR spectra and the higher diameter of the grafted starch granule. Thermoplastic starch from ungrafted granular starch (TPS) and grafted granular starch (TPGS) were obtained by mixing ungrafted or grafted starch with water, glycerol or sorbitol in a mixer. TPS and TPGS behave as plastic materials, and their mechanical properties depend on the type of plasticizer used. Materials with glycerol as the plasticizer exhibited less rigidity than the materials obtained using sorbitol. The presence of starch-g-PLA results in an increase in the elongation of the thermoplastic material. TPS and TPGS were hydrolysed by amylolytic enzymes in short-time periods compared to granular PLA-grafted starches.

36 MATERIALS SCIENCE↗

Investigation of Thermoplastic Polyurethanes Synthesized via Two Different Prepolymers

The man aim of this work was to investigate the effect of the molecular weight of polyols, mixture of prepolymers, and [NCO]/[OH] molar ratio used during the prepolymer chain extending step on the chemical structure, thermomechanical and mechanical properties, and thermal stability of thermoplastic poly(ether-urethane)s In this work thermoplastic poly(ether-urethane)s were synthesized by using polyols with a various molecular weight, 4,4′-diphenylmethane diisocyanate and bio-based glycol. Materials were obtained by a two-step method. The tests were carried out for polyurethanes obtained from a mixture of prepolymers and for reference samples. In the case of materials obtained with using mixture of prepolymers, the ratio of both prepolymers was determined on 50/50 weight percent. Soft segments of materials prepared with using mixture consist of two different polyols. The chemical structure was analyzed using FTIR spectroscopy. The Gaussian deconvolution technique was used to study the hydrogen bonding as well as to decompose carbonyl region of three peaks in various TPUs. The thermal degradation behavior was investigated by using thermogravimetric analysis at heating rates of 10 °C/min. It was confirmed that the mixture of prepolymers has an effect of the degree of phase separation, thermal stability and selected properties of synthesized thermoplastic poly(ether-urethane)s.

36 MATERIALS SCIENCE↗

Determination of melt processing conditions for high performance amorphous thermoplastics for large format additive manufacturing

As the application space for large-scale 3D printed components continues to grow, it is necessary to identify appropriate processing conditions for high-performance thermoplastics on large format Additive Manufacturing (LFAM) systems. This study compares the rheological behavior of a high-performance thermoplastic, polyphenylsulfone (PPSU), with that of a commonly used low-temperature polymer, acrylonitrile butadiene styrene (ABS), to identify suitable processing conditions for large format AM systems. The linear viscoelastic properties (complex viscosity, storage modulus, loss modulus, and tan delta) of these materials are evaluated as a function of temperature, angular frequency, and carbon fiber content. Over the range of frequencies of interest to LFAM (10–100 rad/s), ABS behaves more like an elastic solid whereas PPSU behaves more like a viscous liquid. Here, the addition of 20–35% by weight of carbon fiber increased the shear thinning effect of both thermoplastics, showing a potential variation of 2–3 x over the range of expected LFAM extrusion shear rates (10–100 s –1 ).

36 MATERIALS SCIENCE↗

Internal arcing and lightning strike damage in short carbon fiber reinforced thermoplastic composites

Short carbon fiber reinforced thermoplastic composites (S-CFRTP) are currently used in interior parts of aircraft such as electronic circuitry and assemblies, and their usage in aircraft's exterior is also being studied. In this paper, we present a lightning strike study on S-CFRTPs. High performance thermoplastics such as a polyphenylene sulfide (PPS) reinforced with 50% weight (wt.) short carbon fiber (CF), a polyphenyl sulfone (PPSU) reinforced with 25 % wt. Short CF and a acrylonitrile butadiene styrene (ABS) with 20 % wt. short CF were tested against artificial lightning strikes. All samples were prepared using an extrusion compression molding (ECM) technique. A modified component A (100 kA) of lightning waveform, as defined by SAE ARP 5412-B, was applied. High speed imaging, thermography, scanning electron microscopy (SEM) and ultrasonic non-destructive evaluation were performed to understand the effect of lightning strikes on the thermoplastic panels. The results show that electrical conductivity of the composite, thermal stability of the polymers, and CF orientation significantly affected the damage from artificial lightning strikes. PPS composite had the highest resilience against lightning strike damage, retaining 95% and 89% residual flexural strength and modulus, respectively. CF exfoliation due to internal arcing was observed in the carbon fiber-reinforced ABS polymer (CF-ABS) composite. CF exfoliation damage has been reported for the first time.

36 MATERIALS SCIENCE↗

Thermoplasticity of metallic glasses: Processing and applications

Owing to their extremely low shear viscosity and fragility, bulk metallic glasses (BMGs) are envisioned as new net-shaping material replacing conventionally used crystalline metals for various applications. The first part of this review describes the general technique and kinetics of thermoplastic forming. The second part elaborates on the thermal processing capability of metallic glasses from atomic- to meter-scale. The micro-/nano-structure obtained after various quenching rates followed by temperature, time and heating rate dependent thermoplastic forming is described in the third section. The deformation behavior and flow kinetics of BMGs in terms of composition, mold features, and applied conditions are elaborated in the fourth section. The variation of volume and enthalpy at the supercooled liquid region, strength retention of metallic glasses compared to other conventional metals and alloys, and kinetics of liquid fragility are given in the fifth section. Finite element modeling and molecular dynamics simulations of high-temperature deformation in BMGs are presented in the sixth part. Finally, thermally-formed BMGs used for different applications, including energy, biomedical and micro-optics, are presented in the final part. Altogether, this review provides an overview of shaping capabilities and modifications in the macro-scale properties and short-to-medium range order of BMGs upon thermoplastic forming.

36 MATERIALS SCIENCE↗

Fusion joining of thermoplastic composite wind turbine blades: Lap-shear bond characterization

Wind turbine blades are typically manufactured from a small number of components which are bonded together with an adhesive. Over the life span of a wind turbine, the static and fatigue loads in varying environmental conditions can lead to cracking and/or debonding of the adhesive joints, ultimately leading to blade structural collapse. The objective of this work is to investigate fusion joining of wind turbine blades manufactured using thermoplastic resin. Thermoplastic resins for wind turbine blades can reduce cycle times and energy consumption during manufacturing and facilitate end-of-life recycling and on-site manufacturing. Additionally, fusion joining of these materials can replace adhesives, resulting in stronger and more robust blades. This work showed that, compared to typical adhesives used in wind turbine blades, fusion welding resulted in an increase in both the static and fatigue lap-shear strength as compared to bonded thermoplastic composite coupons. This initial coupon-scale research suggests that there is potential for developing fusion welding techniques for full-scale wind turbine blades.

17 WIND ENERGY↗

Structural validation of a thermoplastic composite wind turbine blade with comparison to a thermoset composite blade

Reactive infusible thermoplastics have the potential to be advantageous for wind turbine blade composites because they are recyclable at end of life, can have reduced manufacturing costs, enable thermal joining and have similar, and in some cases better, structural properties than traditional thermoset epoxy composites. However, these materials are new to the wind industry and there is risk to investing in a material that has not been validated at a blade scale. Industry cannot adopt a new material such as this without large-scale validation and demonstration of system-level advantages in cost and/or performance. This paper presents structural characterization of a 13-m thermoplastic composite wind turbine blade compared to an identical geometry thermoset epoxy blade. In this work, the results of this comparison showed that the flatwise structural static performance and the fatigue performance of the two blades were similar, but the thermoplastic composite blade had increased damping compared to the epoxy blade, which may result in reduced operational loads.

17 WIND ENERGY↗

SU-E-T-71: A Radiochromic Film Based Quantitative Assessment of Thermoplastic Mask Bolus Effect in Head and Neck IMRT/VMAT

Purpose: To quantify the factors leading to thermoplastic mask bolus-associated-increased skin dose in head and neck IMRT/VMAT using EBT2 film. Methods: EBT2 film placed beneath a dual layer 3-point ORFIT head, neck and shoulder mask was used to test the effect of mask thickness, beam modulation, air gap, and beam obliquity on bolus effect. Mask thickness was varied based on the distribution of 1.6mm Orfilight layer on top of 2 mm Efficast layer. Beam modulation was varied by irradiating the film with an open field (no beam modulation) and a step and shoot field (beam modulation). Air gap between mask and film was varied from 0 to 5mm. Beam obliquity was varied by irradiating the film at gantry angles of 0°, 35°, and 70°.Finally, film strips placed on a Rando phantom under an Orfit mask, in regions of expected high dose, were irradiated using 5 IMRT and 5 VMAT plans with various modulation levels (modulation factor 2 to 5) and the results were compared with those obtained placing OSLDs at the same locations. Results: An 18–34% increase in mask bolus effect was observed for three factors where the effect of beam obliquity ≥ beam modulation > mask thickness. No increase in mask bolus effect was observed for change in air gap. A 6–13% increase in dose due to mask bolus effect was observed on film strips. Conclusion: This work underlines the role of beam obliquity and beam modulation combined with thermoplastic mask thickness in increasing mask bolus-associated skin dose in head and neck IMRT/VMAT. One possible method of dose reduction, based on knowledge gained from this work, is inclusion of skin as an avoidance structure in treatment planning. Another approach is to design a mask with the least amount of thermoplastic material necessary for immobilization.

60 APPLIED LIFE SCIENCES↗