Results for “THERMAL ACCOMMODATION COEFFICIENT” — Page 4

NASA NTRS1994

Thermocapillary flow with evaporation and condensation and its effect on liquid retention in low-G fluid acquisition devices

The steady motion, thermal and free surface behavior of a volatile, wetting liquid in microgravity are studied using scaling and numerical techniques. The objective is to determine whether the thermocapillary and two-phase convection arising from thermodynamic nonequilibrium along the porous surfaces of spacecraft liquid acquisition devices could cause the retention failures observed with liquid hydrogen and heated vapor pressurant. Why these devices seem immune to retention loss when pressurized with heated helium or heated directly through the porous structure was also examined. Results show that highly wetting fluids exhibit large negative and positive dynamic pressure gradients towards the meniscus interline when superheated and subcooled, respectively. With superheating, the pressure variation and recoil force arising from liquid/vapor phase change exert the same influence on surface morphology and promote retention. With subcooling, however, the pressure distribution produces a suction that degrades mechanical equilibrium of the surface. This result indicates that thermocapillary-induced deformation arising from subcooling and condensation is the likely cause for retention loss. In addition, increasing the level of nonequilibrium by reducing accommodation coefficient suppresses deformation and explains why this failure mode does not occur in instances of direct screen heating or pressurization with a heated inert gas.

Schmidt, George R.↗

NASA NTRSDate not supplied

Parametric Studies of Human Mars Entry, Descent, and Landing Systems

This paper will present a parametric analysis for entry, descent, and landing (EDL) concepts, enabling rapid systems assessment and tradespace exploration. The entry system uses a hypersonic inflatable aerodynamic decelerator (HIAD) technology. The baseline system includes elements for Mars aerocapture (AC) and EDL segments of the mission. The mission concept of operations (ConOps) begins at Mars arrival in a polar inclination. After performing an aerocapture (AC) maneuver into a pre-defined Mars parking orbit, the AC HIAD is jettisoned. The rest of thevehicle stays in the parking orbit for up to one year. The EDL sequence starts with a deorbit burn at the apoapsis of the parking orbit. After hypersonic entry with the EDL HIAD, the entry system uses a supersonic retropropulsion maneuver to slow the vehicle for the descent and landing segments of the mission. The vehicle will maintain a constant velocity of 2.5 m/s for 5 seconds prior to landing.The system includes a Mars Ascent Vehicle (MAV), Mars Descent Module (MDM), and two HIADs. The MDM includes a primary structure, tanks, engines, and radiators. The primary structure is an aluminum-lithium (Al-Li)cruciform design similar to the structural design of the Apollo Lunar Module. The cruciform planform layout results in four outer bays, with adequate volume in the corners between outer bays to package four landing gears. The central bay is reserved for packaging the MAV and the recessed MAV engines. Two of the outer bays accommodate main propellant tanks, with one LOX and one CH4 tank in each bay. The two remaining outer bays each house four rocket engine systems and associated support structure. Each HIAD comprises an inflatable structure, flexible thermal protection system, gas, and gas generators. The HIAD design used in this study is a stacked-toroid concept with pairing loop straps and radial/chevron straps. The baseline system lands a 20-t payload on the Mars surface. It is assumed the vehicle arrives at 6.2 km/s relative velocity at 90° inclination and is captured to a 1-Sol parking orbit.The baseline design includes many assumptions such as margins, arrival state, ConOps options, parking orbit, physical dimensions, propellant options, and technology concepts. The impact of these parameters are quantified through systems-level sensitivity analyses, which capture the global impact—not at a component level—but at the systems level. The systems-level sensitivities expose major design drivers and importance of each assumption for a design.Through tradespace exploration, a wide range of systems parameters are examined and compared for several feasible design options. Studies have been completed for the following input parameters: payload mass, propellant options, AC/EDL ballistic coefficient, lander thrust to weight ratio (T/W) (surrogate for the maximum EDL g’s),engine specific impulse (Isp), parking orbit, and inclination.The final paper will present and discuss the parametric approach used in the study. It will also include the results of recent systems analyses, sensitivity analyses, and tradespace exploration

Jamshid Samareh↗

DOE OSTI2025

Rapid Solidification Effects in Additively Manufactured Si and SiGe Compositions

SiGe alloys have a proven track record as robust high-temperature thermoelectric materials, powering NASA missions like SNAP-10A, LES-9, and Voyager 1 and 2. Enhancing thermoelectric efficiency hinges on minimizing thermal conductivity while preserving electrical conductivity. Rapid solidification via LPBF can generate microstructural features such as subgrain cellular boundaries and twinning, which may help reduce thermal conductivity while preserving semiconducting behavior. Here, this study investigates the potential of laser powder bed fusion (LPBF) additive manufacturing to fabricate nanostructured Si and SiGe thermoelectric materials. High cooling rates (10 5 to 10 7 K/s) rates inherent to the LPBF process are conducive to forming such nanostructures. Moreover, this fabrication technique could also be suitable for fabricating complex geometries needed to achieve improved device level performance. Process mapping of commercial Si powder with irregular morphology was first performed to understand the LPBF processing behavior of this semiconductor material. Subsequent studies included in-house synthesized B-doped (p-type) Si7 8 Ge 22 spherical powder that was produced via ultrasonic atomization. Scan strategies involved multiple laser exposures to mitigate solidification cracking: a high density of >98% was achieved, but solidification cracking could not be fully eliminated. Subsequently, a high electrical resistivity (i.e., low conductivity) was observed, but the measured Seebeck coefficient, ∼230 μV/K @ 500 °C, proved that good semiconductor material was being fabricated. A subgrain cellular structure (5–10 μm) was observed as defined by Ge segregation to the intercellular boundaries. The remelting strategies helped lower the cooling rates in processing SiGe, but this still resulted in high residual stresses, which induced a remarkably high density of twins (78–95%) to accommodate the deformation. This unique grain structure offers an avenue for phonon scattering and potential improvements in thermoelectric performance.

figure of merit↗

NASA NTRS1996

Cross-Effects in Microgravity Flows

Film growth by chemical/physical vapor deposition is a process of considerable interest in microgravity experiments. The absence of natural convection should allow better control of film growth processes but, in highly non-isothermal ampoules, thermal slip (creep) can become a matter of significant concern. The reported research is a theoretical and experimental investigation of the flow of gas/vapor mixtures under non-continuum conditions. The Boltzmann equation has been solved for a monatomic gas under non-condensing conditions and the various phenomenological coefficients have been computed. Computations for realistic potentials as well as for velocity and creep slip have been completed and the creep slip has been found to be dependent on the type of gas confirming the accuracy of previous variational results. The variational technique has been extended and planar flows calculated via the Burnett solutions. Velocity, diffusion and creep slips have been computed for gas mixtures and previously unknown dependencies of the creep slip on the mixture properties have been observed. Also for gas mixtures, an integral representation of the linearized Boltzmann operator has been developed for use in numerical and variational calculations for all intermolecular force laws. Two, two-bulb capillary systems have been designed, built and tested for the measurements of cross-flows; one of glass for isothermal measurements and one of stainless steel for non-isothermal measurements. Extensive data have been collected for Ar-He and N2-He mixtures at a variety of pressures and mole ratios. Viscosity, velocity slip coefficients and tangential momentum accommodation coefficients have been obtained from measurements with a spinning rotor gauge via a new theory that has been formulated for the spinning rotor gauge in the slip regime. The FIDAP fluid dynamics code has been applied to condensing flows in ampoules in the continuum regime and agreement obtained with the earlier work of Duval.

Loyalka, Sudarshan K.↗

NASA NTRSDate not supplied

Testing of Two Mars Powered Descent Vehicle Concepts in the Langley Unitary Plan Wind Tunnel

Testing was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to investigate the aerodynamic interference of sub-scale versions of two Mars powered descent vehicle concepts at supersonic Mach numbers (2.4 and 3.5): a model based on a blunt hypersonic inflatable aerodynamic decelerator (HIAD) and the second representing a more slender rigid vehicle with body flaps (CobraMRV). Each model was designed to accommodate up to eight nozzles, with the HIAD model having five different nozzle configurations to investigate the effects of nozzle location, cant angle, and area ratio. The models were tested with high pressure air as the nozzle plume gas, and included the following instrumentation: high-speed video, discrete steady state and high-frequency pressure, pressure sensitive paint, and a new flow-through force and moment balance for the HIAD model. The high-speed imagery showed the overall expected growth of the shock layer to increasing thrust levels. The discrete stagnation pressure data on the HIAD model with four and eight blowing nozzles was sensitive to thrust coefficient with the nozzles canted at 0 degrees, whereas having nozzles canted outward 20 degrees and/or being located closer to the heatshield shoulder largely removed that sensitivity. The CobraMRV model stagnation pressure was more sensitive to tunnel Mach number and sideslip angle, due to the nozzle arrangement and plume interference. Pressure sensitive paint data quality was compromised by paint damage from frequent model changes, especially for the HIAD model. However, pressure coefficient data on the CobraMRV model showed the same trends as the discrete pressure measurements, as well as a sensitivity to non-zero sideslip angles. The aerodynamic force coefficients were derived from the pressure sensitive paint data. On the HIAD models, the primary force coefficient decreased with increasing thrust due to the nozzle plumes blocking flow to the heatshield area surrounding the nozzle exist. On the CobraMRV model, the force coefficient was relatively insensitive to thrust coefficient at the lower Mach number when sideslip angle was 0 degrees The force coefficient decreases with increasing thrust coefficient when the sideslip angle is 10 degrees. Balance data quality was negatively impacted by thermal drift issues that were not apparent in pre-test calibration measurements, thus preventing usable test data. Results and lessons learned will be used to take further technology development steps, including more advanced ground test techniques and flight testing.

Karl T Edquist↗

NASA NTRSDate not supplied

Testing of Two Mars Powered Descent Vehicle Concepts in the Langley Unitary Plan Wind Tunnel

Testing was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to investigate the aerodynamic interference of sub-scale versions of two Mars powered descent vehicle concepts at supersonic Mach numbers (2.4 and 3.5): a model based on a blunt hypersonic inflatable aerodynamic decelerator (HIAD) and the second representing a more slender rigid vehicle with body flaps (CobraMRV). Each model was designed to accommodate up to eight nozzles, with the HIAD model having five different nozzle configurations to investigate the effects of nozzle location, cant angle, and area ratio. The models were tested with high pressure air as the nozzle plume gas, and included the following instrumentation: high-speed video, discrete steady state and high-frequency pressure, pressure sensitive paint, and a new flow-through force and moment balance for the HIAD model. The high-speed imagery showed the overall expected growth of the shock layer to increasing thrust levels. The discrete stagnation pressure data on the HIAD model with four and eight blowing nozzles was sensitive to thrust coefficient with the nozzles canted at 0 degrees, whereas having nozzles canted outward 20 degrees and/or being located closer to the heatshield shoulder largely removed that sensitivity. The CobraMRV model stagnation pressure was more sensitive to tunnel Mach number and sideslip angle, due to the nozzle arrangement and plume interference. Pressure sensitive paint data quality was compromised by paint damage from frequent model changes, especially for the HIAD model. However, pressure coefficient data on the CobraMRV model showed the same trends as the discrete pressure measurements, as well as a sensitivity to non-zero sideslip angles. The aerodynamic force coefficients were derived from the pressure sensitive paint data. On the HIAD models, the primary force coefficient decreased with increasing thrust due to the nozzle plumes blocking flow to the heatshield area surrounding the nozzle exist. On the CobraMRV model, the force coefficient was relatively insensitive to thrust coefficient at the lower Mach number when sideslip angle was 0 degrees The force coefficient decreases with increasing thrust coefficient when the sideslip angle is 10 degrees. Balance data quality was negatively impacted by thermal drift issues that were not apparent in pre-test calibration measurements, thus preventing usable test data. Results and lessons learned will be used to take further technology development steps, including more advanced ground test techniques and flight testing.

Supersonic Retropropulsion↗