Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TENSILE STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Size Scaling of Tensile Failure Stress in a Soda-Lime-Silicate Float Glass

The (tensile) strength-size scaling of a float soda-lime silicate glass was studied using biaxial flexure and Hertzian ring crack initiation testing. The examined Weibull effective areas spanned ~ 0.4 to 48,000 mm2. Both the air- and tin-sides were tested. The air side was stronger than the tin side as others have observed; however, the differences in their characteristic strengths decreased with decreasing effective area, and their strengths converged for effective areas smaller than ~ 100 mm2. The failure stress at the smallest effective area examined for the tin-side was ~ 500% greater than that at the largest effective area while that difference was ~ 250% for the air- side. A Weibull modulus change at ~ 100 mm2 suggests different strength-limiting flaw types were dominant below and above that effective area. These results reinforce the importance to interpret and use tensile strength of glass in context to how much of its area is being tensile stressed.

36 MATERIALS SCIENCE↗

Stress corrosion susceptibility of stress-coined fastener holes in aircraft structures

The cold working process of stress coining is used to provide fatigue improvement of fastener holes in aircraft structures. The cold working produces a radial flow of the metal. The residual stresses resulting from stress coining provide protection against fatigue damage by opposing the applied tensile stresses in service at the edge of the fastener hole. However, it is shown in this paper that in addition to the compressive stresses surrounding the stress coined hole, there are tensile stresses that result from the coining operation and that these residual tensile stresses can have a deleterious effect on the stress corrosion susceptibility of the postcoined structure.

Carter, A. E.↗

Evolution of Microstructure, Residual Stress, and Tensile Properties of Additively Manufactured Stainless Steel Under Heat Treatments

This study investigated the microstructure, residual stress and tensile properties of the directed energy deposited stainless steel 316L (SS316L) under thermal annealing. Microstructure characterization shows the as-printed sample has laser-generated patterns where dendritic structure is observed at the edge of the patterns and cellular structure dominates the interior region. Here, the thermal annealing at 983 and 1093°C effectively removes the dendritic/cellular structures. Synchrotron X-ray diffraction reveals that the as-fabricated SS316L exhibits compressive residual stress of -197.4 MPa. The stress is greatly relieved to -53.8 MPa after annealing at 1093°C. The room temperature tensile testing indicates that the yield strength and ultimate tensile strength drop from 378 and 502 MPa in the as-printed sample to 258 and 446 MPa in the annealed samples (1093°C), respectively. Our study provides insights into the relationship between microstructure, residual stress, and tensile properties of laser additive manufactured SS316L.

36 MATERIALS SCIENCE↗

Structure disorder degree of polysilicon thin films grown by different processing: Constant C from Raman spectroscopy

Flat, low-stress, boron-doped polysilicon thin films were prepared on single crystalline silicon substrates by low pressure chemical vapor deposition. It was found that the polysilicon films with different deposition processing have different microstructure properties. The confinement effect, tensile stresses, defects, and the Fano effect all have a great influence on the line shape of Raman scattering peak. But the effect results are different. The microstructure and the surface layer are two important mechanisms dominating the internal stress in three types of polysilicon thin films. For low-stress polysilicon thin film, the tensile stresses are mainly due to the change of microstructure after thermal annealing. But the tensile stresses in flat polysilicon thin film are induced by the silicon carbide layer at surface. After the thin film doped with boron atoms, the phenomenon of the tensile stresses increasing can be explained by the change of microstructure and the increase in the content of silicon carbide. We also investigated the disorder degree states for three polysilicon thin films by analyzing a constant C. It was found that the disorder degree of low-stress polysilicon thin film larger than that of flat and boron-doped polysilicon thin films due to the phase transformation after annealing. After the flat polysilicon thin film doped with boron atoms, there is no obvious change in the disorder degree and the disorder degree in some regions even decreases.

36 MATERIALS SCIENCE↗

Application of an Elongated Kelvin Model to Space Shuttle Foams

Spray-on foam insulation is applied to the exterior of the Space Shuttle s External Tank to limit propellant boil-off and to prevent ice formation. The Space Shuttle foams are rigid closed-cell polyurethane foams. The two foams used most extensively on the Space Shuttle External Tank are BX-265 and NCFI24-124. Since the catastrophic loss of the Space Shuttle Columbia, numerous studies have been conducted to mitigate the likelihood and the severity of foam shedding during the Shuttle s ascent to space. Due to the foaming and rising process, the foam microstructures are elongated in the rise direction. As a result, these two foams exhibit a non-isotropic mechanical behavior. In this paper, a detailed microstructural characterization of the two foams is presented. The key features of the foam cells are summarized and the average cell dimensions in the two foams are compared. Experimental studies to measure the room temperature mechanical response of the two foams in the two principal material directions (parallel to the rise and perpendicular to the rise) are also reported. The measured elastic modulus, proportional limit stress, ultimate tensile stress and the Poisson s ratios for the two foams are compared. The generalized elongated Kelvin foam model previously developed by the authors is reviewed and the equations which result from this model are presented. The resulting equations show that the ratio of the elastic modulus in the rise direction to that in the perpendicular-to-rise direction as well as the ratio of the strengths in the two material directions is only a function of the microstructural dimensions. Using the measured microstructural dimensions and the measured stiffness ratio, the foam tensile strength ratio and Poisson s ratios are predicted for both foams. The predicted tensile strength ratio is in close agreement with the measured strength ratios for both BX-265 and NCFI24-124. The comparison between the predicted Poisson s ratios and the measured values is not as favorable.

Sullivan, Roy M.↗

Effect of tensile mean stress on fatigue behavior of single-crystal and directionally solidified superalloys

Two nickel base superalloys, single crystal PWA 1480 and directionally solidified MAR-M 246 + Hf, were studied in view of the potential usage of the former and usage of the latter as blade materials for the turbomachinery of the space shuttle main engine. The baseline zero mean stress (ZMS) fatigue life (FL) behavior of these superalloys was established, and then the effect of tensile mean stress (TMS) on their FL behavior was characterized. At room temperature these superalloys have lower ductilities and higher strengths than most polycrystalline engineering alloys. The cycle stress-strain response was thus nominally elastic in most of the fatigue tests. Therefore, a stress range based FL prediction approach was used to characterize both the ZMS and TMS fatigue data. In the past, several researchers have developed methods to account for the detrimental effect of tensile mean stress on the FL for polycrystalline engineering alloys. However, the applicability of these methods to single crystal and directionally solidified superalloys has not been established. In this study, these methods were applied to characterize the TMS fatigue data of single crystal PWA 1480 and directionally solidified MAR-M 246 + Hf and were found to be unsatisfactory. Therefore, a method of accounting for the TMS effect on FL, that is based on a technique proposed by Heidmann and Manson was developed to characterize the TMS fatigue data of these superalloys. Details of this method and its relationship to the conventionally used mean stress methods in FL prediction are discussed.

Kalluri, Sreeramesh↗

Effect of tensile mean stress on fatigue behavior of single-crystal and directionally solidified superalloys

Two nickel base superalloys, single crystal PWA 1480 and directionally solidified MAR-M 246 + Hf, were studied in view of the potential usage of the former and usage of the latter as blade materials for the turbomachinery of the Space Shuttle main engine. The baseline zero mean stress (ZMS) fatigue life (FL) behavior of these superalloys was established, and then the effect of tensile mean stress (TMS) on their FL behavior was characterized. A stress range based FL prediction approach was used to characterize both the ZMS and TMS fatigue data. In the past, several researchers have developed methods to account for the detrimental effect of tensile mean stress on the FL for polycrystalline engineering alloys. These methods were applied to characterize the TMS fatigue data of single crystal PWA 1480 and directionally solidified MAR-M 246 + Hf and were found to be unsatisfactory. Therefore, a method of accounting for the TMS effect on FL, that is based on a technique proposed by Heidmann and Manson was developed to characterize the TMS fatigue data of these superalloys. Details of this method and its relationship to the conventionally used mean stress methods in FL prediction are discussed.

Kalluri, Sreeramesh↗

The effect of a prior short-term ageing on mechanical and creep properties of P92 steel

Highlights: • The results of simulated ageing at 650°C allows to estimate degradation of P92 steam pipes due to accidental overheating. • Simulated ageing has only a slight effect on ambient tensile properties and hardness. • A sudden decrease in impact properties occurred after ageing for 2000h. The FATT of about 25°C was determined. • The creep results show a clear detrimental influence of tempering ageing on the creep strength. • No Z-phase precipitation occurred due to the ageing process. - Abstract: We have investigated the effect of prior short-term ageing on the mechanical and creep properties of tungsten and boron modified 9%Cr ferritic steel (ASTM Grade P92 steel), to provide material data base for the estimation of material degradation due to occurrence of accidental overheating in the early stage of service loading. The steel was aged at 650 °C for up to 100, 200, 500, 1000, 2000 and 5000 h prior to mechanical and creep testing. Changes in the microstructure during ageing had a slight effect on the reduction of room temperature tensile properties. A sudden decrease on impact properties occurred after ageing for 2000 h, but the occurred impact energy of about 70 J is in accordance with the specified minimum value of 68 J at room temperature for the virgin condition. The creep behaviour of P92 steel in the as-received condition and after different isothermal ageing exposures prior to creep was investigated at 600 and 650 °C in the power-law creep regime. The initial applied tensile stress ranged from 90 to 200 MPa. The results clearly show a detrimental influence of isothermal ageing on creep properties even after a few hundred hours. Based on microstructure analysis, which was done mostly in a qualitative way, a significant decrease in the creep life after ageing resulted from changes of the dislocation substructure and instability of Laves phase and M{sub 23}C{sub 6} particles.

36 MATERIALS SCIENCE↗

Suppression of boron-oxygen defects in Czochralski silicon by carbon co-doping

We have investigated the influence of carbon co-doping on the formation of boron-oxygen defects in Czochralski silicon. It is found that carbon can effectively suppress the formation of boron-oxygen defects. Based on our experiments and first-principle theoretical calculations, it is believed that this effect is attributed to the formation of more energetically favorable carbon-oxygen complexes. Moreover, the diffusion of oxygen dimers in carbon co-doped silicon also becomes more difficult. All these phenomena should be associated with the tensile stress field induced by carbon doping in silicon.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Tension and compression fatigue response of unnotched 3D braided composites

The unnotched compression and tension fatigue response of a 3-D braided composite was measured. Both gross compressive stress and tensile stress were plotted against cycles to failure to evaluate the fatigue life of these materials. Damage initiation and growth was monitored visually and by tracking compliance change during cycle loading. The intent was to establish by what means the strength of a 3-D architecture will start to degrade, at what point will it degrade beyond an acceptable level, and how this material will typically fail.

Portanova, M. A.↗

Open-Mode Debonding Analysis of Curved Sandwich Panels Subjected to Heating and Cryogenic Cooling on Opposite Faces

Increasing use of curved sandwich panels as aerospace structure components makes it vital to fully understand their thermostructural behavior and identify key factors affecting the open-mode debonding failure. Open-mode debonding analysis is performed on a family of curved honeycomb-core sandwich panels with different radii of curvature. The curved sandwich panels are either simply supported or clamped, and are subjected to uniform heating on the convex side and uniform cryogenic cooling on the concave side. The finite-element method was used to study the effects of panel curvature and boundary condition on the open-mode stress (radial tensile stress) and displacement fields in the curved sandwich panels. The critical stress point, where potential debonding failure could initiate, was found to be at the midspan (or outer span) of the inner bonding interface between the sandwich core and face sheet on the concave side, depending on the boundary condition and panel curvature. Open-mode stress increases with increasing panel curvature, reaching a maximum value at certain high curvature, and then decreases slightly as the panel curvature continues to increase and approach that of quarter circle. Changing the boundary condition from simply supported to clamped reduces the magnitudes of open-mode stresses and the associated sandwich core depth stretching.

Ko, William L.↗

Mirrors for High Resolution X-Ray Optics---Figure Preserving IR/PT Coating

Coating stress of 10 - 20 nm of Ir is sufficiently high to distort the figure of arc-second thin lightweight mirrors. For iridium: --Stress sigma ~ 4 GPa for 15 nm film implies 60 Nm integrated stress-- Need less than 3 N/m (or stress less than 200 MPa) for sub-arcsecond optics. Basic Approaches for Mitigation. A. Annealing the film-- Glass can be heat up to 400 C without distortion. Silicon is even more resistant.-- It was found that recovery is limited by residual thermal stress from taking the mirror down from high T. B. Coating bi-layer films with compressive stress with tensile stress. C. Front-and-back coating with magnetron sputtering or atomic layer deposition-- Sputtering involve spanning of substrates. Geometric difference in setup (convexness/concaveness of curved mirrors) does not permit precise front-and-back matching-- Atomic layer deposition can provide a uniform deposition front and back simultaneously.

MIRRORS FOR HIGH RESOLUTION X-RAY OPTICS↗

STRESS CORROSION CRACKING IN TEAR DROP SPECIMENS

Laboratory tests were conducted to investigate the stress corrosion cracking (SCC) of 304L stainless steel used to construct the containment vessels for the storage of plutonium-bearing materials. The tear drop corrosion specimens each with an autogenous weld in the center were placed in contact with moist plutonium oxide and chloride salt mixtures. Cracking was found in two of the specimens in the heat affected zone (HAZ) at the apex area. Finite element analysis was performed to simulate the specimen fabrication for determining the internal stress which caused SCC to occur. It was found that the tensile stress at the crack initiation site was about 30% lower than the highest stress which had been shifted to the shoulders of the specimen due to the specimen fabrication process. This finding appears to indicate that the SCC initiation took place in favor of the possibly weaker weld/base metal interface at a sufficiently high level of background stress. The base material, even subject to a higher tensile stress, was not cracked. The relieving of tensile stress due to SCC initiation and growth in the HAZ and the weld might have foreclosed the potential for cracking at the specimen shoulders where higher stress was found.

36 MATERIALS SCIENCE↗

Cell prestress. I. Stiffness and prestress are closely associated in adherent contractile cells

The tensegrity hypothesis holds that the cytoskeleton is a structure whose shape is stabilized predominantly by the tensile stresses borne by filamentous structures. Accordingly, cell stiffness must increase in proportion with the level of the tensile stress, which is called the prestress. Here we have tested that prediction in adherent human airway smooth muscle (HASM) cells. Traction microscopy was used to measure the distribution of contractile stresses arising at the interface between each cell and its substrate; this distribution is called the traction field. Because the traction field must be balanced by tensile stresses within the cell body, the prestress could be computed. Cell stiffness (G) was measured by oscillatory magnetic twisting cytometry. As the contractile state of the cell was modulated with graded concentrations of relaxing or contracting agonists (isoproterenol or histamine, respectively), the mean prestress ((t)) ranged from 350 to 1,900 Pa. Over that range, cell stiffness increased linearly with the prestress: G (Pa) = 0.18(t) + 92. While this association does not necessarily preclude other interpretations, it is the hallmark of systems that secure shape stability mainly through the prestress. Regardless of mechanism, these data establish a strong association between stiffness of HASM cells and the level of tensile stress within the cytoskeleton.

NASA Discipline Cell Biology↗

Separating the Influence of Environment from Stress Relaxation Effects on Dwell Fatigue Crack Growth in a Nickel-Base Disk Alloy

Both environmental embrittlement and crack tip visco-plastic stress relaxation play a significant role in determining the dwell fatigue crack growth (DFCG) resistance of nickel-based disk superalloys. In the current study performed on the Low Solvus High Refractory (LSHR) disk alloy, the influence of these two mechanisms were separated so that the effects of each could be quantified and modeled. Seven different microstructural variations of LSHR were produced by controlling the cooling rate and the subsequent aging and thermal exposure heat treatments. Through cyclic fatigue crack growth testing performed both in air and vacuum, it was established that four out of the seven LSHR heat treatments evaluated, possessed similar intrinsic environmental resistance to cyclic crack growth. For these four heat treatments, it was further shown that the large differences in dwell crack growth behavior which still persisted, were related to their measured stress relaxation behavior. The apparent differences in their dwell crack growth resistance were attributed to the inability of the standard linear elastic fracture mechanics (LEFM) stress intensity parameter to account for visco-plastic behavior. Crack tip stress relaxation controls the magnitude of the remaining local tensile stresses which are directly related to the measured dwell crack growth rates. It was hypothesized that the environmentally weakened grain boundary crack tip regions fail during the dwells when their strength is exceeded by the remaining local crack tip tensile stresses. It was shown that the classical creep crack growth mechanisms such as grain boundary sliding did not contribute to crack growth, but the local visco-plastic behavior still plays a very significant role by determining the crack tip tensile stress field which controls the dwell crack growth behavior. To account for the influence of the visco-plastic behavior on the crack tip stress field, an empirical modification to the LEFM stress intensity parameter, Kmax, was developed by incorporating into the formulation the remaining stress level concept as measured by simple stress relaxation tests. The newly proposed parameter, Ksrf, did an excellent job in correlating the dwell crack growth rates for the four heat treatments which were shown to have similar intrinsic environmental cyclic fatigue crack growth resistance.

Dwell crack growth↗

Separating the Influence of Environment from Stress Relaxation Effects on Dwell Fatigue Crack Growth

Seven different microstructural variations of LSHR were produced by controlling the cooling rate and the subsequent aging and thermal exposure heat treatments. Through cyclic fatigue crack growth testing performed both in air and vacuum, it was established that four out of the seven LSHR heat treatments evaluated, possessed similar intrinsic environmental resistance to cyclic crack growth. For these four heat treatments, it was further shown that the large differences in dwell crack growth behavior which still persisted, were related to their measured stress relaxation behavior. The apparent differences in their dwell crack growth resistance were attributed to the inability of the standard linear elastic fracture mechanics (LEFM) stress intensity parameter to account for visco-plastic behavior. Crack tip stress relaxation controls the magnitude of the remaining local tensile stresses which are directly related to the measured dwell crack growth rates. It was hypothesized that the environmentally weakened grain boundary crack tip regions fail during the dwells when their strength is exceeded by the remaining local crack tip tensile stresses. It was shown that the classical creep crack growth mechanisms such as grain boundary sliding did not contribute to crack growth, but the local visco-plastic behavior still plays a very significant role by determining the crack tip tensile stress field which controls the dwell crack growth behavior. To account for the influence of the visco-plastic behavior on the crack tip stress field, an empirical modification to the LEFM stress intensity parameter, Kmax, was developed by incorporating into the formulation the remaining stress level concept as measured by simple stress relaxation tests. The newly proposed parameter, Ksrf, did an excellent job in correlating the dwell crack growth rates for the four heat treatments which were shown to have similar intrinsic environmental cyclic fatigue crack growth resistance.

environmental damage↗

Mechanical properties and phase composition of potential biodegradable Mg-Zn-Mn-base alloys with addition of rare earth elements

Mechanical properties and creep resistance of the MgY4Zn1Mn1 alloy in the as cast as well as in the T5 condition were compared to those of the MgCe4Zn1Mn1 alloy in the same conditions. Yield tensile stress and ultimate tensile strength of the MgY4Zn1Mn1 alloy are slightly better in the temperature range 20 deg. C-400 deg. C than these of the MgCe4Zn1Mn1 alloy. Better thermal stability of ultimate tensile strength was observed in the T5 treated MgCe4Zn1Mn1 alloy than in this material in the as cast condition. An outstanding creep resistance at 225 deg. C-350 deg. C found in the MgY4Zn1Mn1 alloy is due to the existence of the 18R long period stacking structure persisting in this alloy even a long heat treatment of 500 deg. C/32 h. No similar stacking effects happen when Ce substitutes Y in approximately the same concentration. The creep resistance deteriorates considerably in the MgCe4Zn1Mn1 alloy. Rectangular particles of the equilibrium Mg{sub 12}Ce phase dominate in the microstructure of as cast as well as of high temperature heat-treated MgCe4Zn1Mn1 alloy. A population of small oval particles containing Mg and Zn develops additionally during annealing of this alloy. These particles pin effectively dislocations and can be responsible for the better thermal stability of the T5 treated material.

36 MATERIALS SCIENCE↗