SEARCH · Engineering Papers

Results for “Spin coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

62 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1963

The solar cells and their mounting

Objectives in development of the solar plant for the Telstar spacecraft were to provide a power source which would withstand launching stresses and the expected space environment, with optimum end-of-life performance. Radiation damage to the silicon solar cells is the primary factor limiting their useful life; the effect of energetic protons or electrons is the generation of recombination centers in the silicon which reduce the minority-carrier diffusion length and therefore the long-wave response of the cell. The spacecraft solar cells use the n-on-p structure, in preference to conventional p-on-n structure, to obtain a factor of 3 to 10 increased life expectancy. Response to light in the 0.4 to 0.7 micron range is enhanced by using a thin n-layer (about 0.5 micron) and an antireflection coating with minimum reflectance at 0.55 micron wavelength. Early estimates of electron and proton fluxes in the satellite orbit showed that even the best cells would not give sufficient life without radiation shielding. Therefore the cells are protected against electrons of energy up to 1 Mev by 0.3 gm/sq. cm sapphire cover plates. The cell mountings are designed to withstand peak vibration stresses of 200 g and repeated temperature cycles from +65°C to −100°C. The 3600-cell solar power plant is composed of 300 twelve-cell groups of 1 cm × 2 cm cells, yielding a nominal initial power of 14 watts at 28 volts for any spin-axis orientation relative to the sun. Telemetry information on performance of the solar plant indicates degradation of the shielded solar cells equal to that measured in the laboratory on unshielded cells with a 1-Mev normal incidence flux of 6 × 10^(12) electrons/(sq. cm day). From this comparison it is estimated that the plant will degrade to 68 per cent of its initial output after two years in orbit.

SPACECRAFT POWER SUPPLY↗

NASA NTRS2004

Space Technology 5: Pathfinder for Future Micro-Sat Constellations

The Space Technology 5 (ST-5) Project, currently in the implementation phase, is part of the National Aeronautics and Space Administration (NASA) s New Millennium Program (NMP). ST-5 will consist of a constellation of three miniature satellites, each with mass less than 25 kg and size approximately 60 cm by 30 cm. ST-5 addresses technology challenges, as well as fabrication, assembly, test and operations strategies for future micro-satellite missions. ST-5 will be deployed into a highly eccentric, geo-transfer orbit (GTO). This will expose the spacecraft to a high radiation environment as well as provide a low level magnetic background. A three-month flight demonstration phase is planned to validate the technologies and demonstrate concepts for future missions. Each ST-5 spacecraft incorporates NMP competitively-selected breakthrough technologies. These include Cold Gas Micro-Thrusters for propulsion and attitude control, miniature X-band transponder for space-ground communications, Variable Emittance Coatings for dynamic thermal control, and CULPRiT ultra low power logic chip used for Reed-Solomon encoding. The ST-5 spacecraft itself is a technology that can be infused into future missions. It is a fully functional micro-spacecraft built within tight volume and mass constraints. It is built to withstand a high radiation environment, large thermal variations, and high launch loads. The spacecraft power system is low-power and low-voltage, and is designed to turn on after separation &om the launch vehicle. Some of the innovations that are included in the ST-5 design are a custom spacecraft deployment structure, magnetometer deployment boom, nutation damper, X-band antenna, miniature spinning sun sensor, solar array with triple junction solar cells, integral card cage assembly containing single card Command and Data Handling and Power System Electronics, miniature magnetometer, and lithium ion battery. ST-5 will demonstrate the ability of a micro satellite to perform research-quality science. Each ST-5 spacecraft will deploy a precision magnetometer to be used both for attitude determination and as a representative science instrument. The spacecraft has been developed with a low magnetic signature to avoid interference with the magnetometer. The spacecraft will be able to detect and respond autonomously to science events, i.e. significant changes in the magnetic field measurements. The three spacecraft will be a pathfinder for future constellation missions. They will be deployed to demonstrate an appropriate geometry for scientific measurements as a constellation. They will be operationally managed as a constellation, demonstrating automation and communication strategies that will be useful for future missions. The technologies and future mission concepts will be validated both on the ground and in space. Technologies will be validated on the ground by a combination of component level and system level testing of the flight hardware in a thermal vacuum environment. In flight, specific validation runs are planned for each of the technologies. Each validation run consists of one or more orbits with a specific validation objective. This paper will describe the ST-5 mission, and the applicability of the NMP technologies, spacecraft, and mission concepts to future missions. It will also discuss the validation approach for the ST-5 technologies and mission concepts.

Carlisle, Candace↗

NASA NTRS1993

Fuel injector design for high temperature aircraft engine

The objective of the Innovative High Temperature Aircraft Engine Fuel Nozzle Program was to design and evaluate a nozzle capable of operating at a combustor inlet air temperature of 1600 F (1144 K) and a fuel temperature of 350 F (450 K). The nozzle was designed to meet the same performance requirements and fit within the size envelope of a current production dual orifice fuel nozzle. The design approach was to use improved thermal protection and fuel passage geometry in combination with fuel passage surface treatment to minimize coking at these extreme fuel and air temperatures. Heat transfer models of several fuel injector concepts were used to optimize the thermal protection, while sample tube coking tests were run to evaluate the effect of surface finish, coatings and tube material on the coking rate. Based on heat transfer analysis, additional air gaps, reduced fuel passage flow area and use of ceramic tip components reduced local fuel wetted wall temperatures by more than 200 F (100 K) when compared to a current production fuel nozzle. Sample tube coking test results showed the importance of surface finish on the fuel coking rate. Therefore, a one micro-inch (0.025 micron) roughness was specified for all fuel passage surfaces. A novel flow divider valve in the tip was also employed to reduce weight, allow room for additional thermal protection, and provide back pressure to reduce the risk of fuel vaporization. The fuel nozzle was fabricated and evaluated in a series of high temperature coking tests. Initial results of these tests indicate that thermal protection and surface treatments were partially successful in preventing nozzle fouling, but additional refinement of the internal flowpath is needed to prevent buildup of coke particles that partially blocked the spin slots which meter the nozzle fuel flow.

R. W. Stickles↗

NASA NTRS1991

The composition and plasma signature of a large dust impact on the Giotto spacecraft

At about 14,800 km from the Comet Halley nucleus, on the inbound leg, at least six of the sensors onboard the Giotto spacecraft observed an unusual, brief (about 30 to 500 ms) event: the ion-mass spectrometer data show a brief flow of energetic (up to several hundred electron volts) plasma consisting of protons, water group, and heavier ions. The Johnstone plasma analyzer data show a short burst of plasma, while the dust impact detector system data show an impact event in four of its detectors. The magnetometer signature of the event shows two brief dips in the field. The sudden change in the spacecraft attitude and spin rate observed by the camera at that same time has been interpreted as the result of a large (5 mg or more) dust-particle impact on the front bumper shield of the spacecraft. In addition, at about the same time the spacecraft star-tracker suffered damage. The report combines direct measurements of the composition and dynamics of a dust-impact plasma cloud, the dust particle mass, and the location of the impact on the spacecraft. Analysis of the data indicate that the impacting particle was water or ice-bearing, possibly loosely compared, and was composed of one or more of: carbon, nitrogen, and silicon.

Goldstein, R.↗

NASA NTRS2001

Thermo-Elastic Analysis of Internally Cooled Structures Using a Higher Order Theory

This paper presents the results of a study on the thermomechanical behavior of internally cooled silicon nitride structures. Silicon nitride is under consideration for elevated temperature aerospace engine applications. and techniques for lowering the operating temperature of structures composed of this material are under development. Lowering the operating temperature provides a large payoff in terms of fatigue life and may be accomplished through the use of thermal barrier coatings (TBC's) and the novel concept of included cooling channels. Herein, an in-depth study is performed on the behavior of a flame-impinged silicon nitride plate with a TBC and internal channels cooled by forced air. The analysis is performed using the higher order theory for functionally graded materials (HOTFGM), which has been developed through NASA Glenn Research Center funding over the past several years. HOTFGM was chosen over the traditional finite element approach as a prelude to an examination of functionally graded silicon nitride structures for which HOTFGM is ideally suited. To accommodate the analysis requirement% of the internally cooled plate problem, two crucial enhancements were made to the two-dimensional Cartesian-based version of HOTFGM. namely, incorporation of internal boundary capabilities and incorporation of convective boundary conditions. Results indicate the viability and large benefits of cooling the plate via forced air through cooling channels. Furthermore, cooling can positively impact the stress and displacement fields present in the plate, yielding an additional payoff in terms of fatigue life. Finally, a spin-off capability resulted from inclusion of internal boundaries within HOTFGM; the ability to simulate the thermo-elastic response of structures with curved surfaces. This new capability is demonstrated, and through comparison with an analytical solution, shown to be viable and accurate.

Arnold, Steven M.↗

NASA NTRS2013

Pressure-Sensitive Paints Advance Rotorcraft Design Testing

The rotors of certain helicopters can spin at speeds as high as 500 revolutions per minute. As the blades slice through the air, they flex, moving into the wind and back out, experiencing pressure changes on the order of thousands of times a second and even higher. All of this makes acquiring a true understanding of rotorcraft aerodynamics a difficult task. A traditional means of acquiring aerodynamic data is to conduct wind tunnel tests using a vehicle model outfitted with pressure taps and other sensors. These sensors add significant costs to wind tunnel testing while only providing measurements at discrete locations on the model's surface. In addition, standard sensor solutions do not work for pulling data from a rotor in motion. "Typical static pressure instrumentation can't handle that," explains Neal Watkins, electronics engineer in Langley Research Center s Advanced Sensing and Optical Measurement Branch. "There are dynamic pressure taps, but your costs go up by a factor of five to ten if you use those. In addition, recovery of the pressure tap readings is accomplished through slip rings, which allow only a limited amount of sensors and can require significant maintenance throughout a typical rotor test." One alternative to sensor-based wind tunnel testing is pressure sensitive paint (PSP). A coating of a specialized paint containing luminescent material is applied to the model. When exposed to an LED or laser light source, the material glows. The glowing material tends to be reactive to oxygen, explains Watkins, which causes the glow to diminish. The more oxygen that is present (or the more air present, since oxygen exists in a fixed proportion in air), the less the painted surface glows. Imaged with a camera, the areas experiencing greater air pressure show up darker than areas of less pressure. "The paint allows for a global pressure map as opposed to specific points," says Watkins. With PSP, each pixel recorded by the camera becomes an optical pressure tap. "Instead of having 100 or 200 pressure taps, you can have in theory several million, up to whatever the resolution of your camera is." Watkins explains that typical wind tunnel testing requires two models: one with very little instrumentation, and a pressure model with a significant amount of sensors applied. "If you can make all of your measurements on one model with PSP, you've decreased your model costs by at least a factor of two and preferably your testing costs by about that much," he says. PSP technology has been around for almost 20 years, but a PSP solution for gathering instantaneous dynamic pressure data from surfaces moving at high speeds, such as rotor blades, was not available until a NASA partnership led to a game-changing innovation.

Source record↗

NASA NTRS2017

Active Electrostatic flight for airless bodies

The environment near the surface of asteroids, comets, and the Moon is electrically charged due to the Sun’s photoelectric bombardment and lofting dust, which follows the Sun illumination as the body spins. Charged dust is ever present, in the form of dusty plasma, even at high altitudes, following the solar illumination. If a body with high surface resistivity is exposed to the solar wind and solar radiation, sunexposed areas and shadowed areas become differentially charged. The E-Glider (Electrostatic Glider) is an enabling capability for operation at airless bodies, a solution applicable to many types of in-situ missions, which leverages the natural environment. This platform directly addresses the "All Access Mobility" Challenge, one of the NASA’s Space Technology Grand Challenges. Exploration of comets, asteroids, moons and planetary bodies is limited by mobility on those bodies. The lack of an atmosphere, the low gravity levels, and the unknown surface soil properties pose a very difficult challenge for all forms of know locomotion at airless bodies. This EGlider levitates by extending thin, charged, appendages, which are also articulated to direct the levitation force in the most convenient direction for propulsion and maneuvering. The charging is maintained through continuous charge emission. It lands, wherever it is most convenient, by retracting the appendages or by firing a cold-gas thruster, or by deploying an anchor. Preliminary calculations indicate that a 1 kg mass can be electrostatically levitated in a microgravity field with a 2 m diameter electrostatically inflated ribbon structure at 19kV, hence the need for a “balloon-like” system. The wings could be made of very thin Au-coated Mylar film, which are electrostatically inflated, and would provide the lift due to electrostatic repulsion with the naturally charged asteroid surface. Since the E-glider would follow the Sun’s illumination, the solar panels on the vehicle would constantly charge a battery. Further articulation at the root of the lateral strands or inflated membrane wings, would generate a component of lift depending on the articulation angle, hence a selective maneuvering capability which, to all effects, would lead to electrostatic (rather than aerodynamic) flight.

Schaub, Hanspeter↗

NASA NTRS2018

E-Glider: Active Electrostatic Flight for Airless Body Exploration

The environment near the surface of asteroids, comets, and the Moon is electrically charged due to the Sun's photoelectric bombardment and lofting dust, which follows the Sun illumination as the body spins. Chargeddust is ever present, in the form of dusty plasma, even at high altitudes, following the solar illumination. If abody with high surface resistivity is exposed to the solar wind and solar radiation, sun-exposed areas andshadowed areas become differentially charged. The E-Glider (Electrostatic Glider) is an enabling capability foroperation at airless bodies, a solution applicable to many types of in-situ mission concepts, which leverages thenatural environment. With the E-Glider, we transform a problem (spacecraft charging) into an enablingtechnology, i.e. a new form of mobility in microgravity environments using new mechanisms and maneuveringbased on the interaction of the vehicle with the environment. Consequently, the vision of the E-Glider is toenable global scale airless body exploration with a vehicle that uses, instead of avoids, the local electricallycharged environment. This platform directly addresses the "All Access Mobility" Challenge, one of the NASA'sSpace Technology Grand Challenges. Exploration of comets, asteroids, moons and planetary bodies is limitedby mobility on those bodies. The lack of an atmosphere, the low gravity levels, and the unknown surface soilproperties pose a very difficult challenge for all forms of know locomotion at airless bodies. This E-Gliderlevitates by extending thin, charged, appendages, which are also articulated to direct the levitation force in themost convenient direction for propulsion and maneuvering. The charging is maintained through continuouscharge emission. It lands, wherever it is most convenient, by retracting the appendages or by firing a cold-gasthruster, or by deploying an anchor. The wings could be made of very thin Au-coated Mylar film, which areelectrostatically inflated, and would provide the lift due to electrostatic repulsion with the naturally chargedasteroid surface. Since the E-glider would follow the Sun's illumination, the solar panels on the vehicle wouldconstantly charge a battery. Further articulation at the root of the lateral strands or inflated membrane wings,would generate a component of lift depending on the articulation angle, hence a selective maneuveringcapability which, to all effects, would lead to electrostatic (rather than aerodynamic) flight. Preliminarycalculations indicate that a 1 kg mass can be electrostatically levitated in a microgravity field with a 2 mdiameter electrostatically inflated ribbon structure at 19kV, hence the need for a "balloon-like" system. Due tothe high density and the photo-electron sheath and associate small Debye length, significant power is requiredto levitate even a few kilograms. The power required is in the kilo-Watt range to maintain a constant chargelevel.

Electrostatic Flight↗