Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Selective wetting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Solid surface wetting and the deployment of drops in microgravity

The complete or partial deployment of liquid samples in low gravity is primarily influenced by the interfacial properties of the specific liquid and solid materials used because the overwhelming bias of the Earth gravitational acceleration is removed. This study addresses the engineering aspects of injecting and deploying drops of prescribed volume into an acoustic positioning chamber in microgravity. The specific problems of interest are the design, testing, and implementation of injector tips to be used in a simultaneously retracting dual-injector system in the Drop Physics Module microgravity experiment facility. Prior to release, the liquid to be deployed must be retained within a restricted area at the very end of the injectors under dynamic stimuli from the continuous injection flow as well as from the stepped motion of the injectors. The final released drop must have a well determined volume and negligible residual linear or angular momentum. The outcome of Earth-based short-duration low gravity experiments had been the selection of two types of injector tips which were flown as back-up parts. They were successfully utilized during the USML-1 Spacelab mission as the primary tips. The combination of a larger contact surface, liquid pinning with a sharp edge, and selective coating of strategic tip surfaces with a non-wetting compound has allowed a significant increase in the success rate of deployment of simple and compound drops of aqueous solutions of glycerol and silicone oil. The diameter of the samples studied in the Drop Physics Module range between 0.3 and 2.7 cm. The tests conducted on-orbit with a manually operated small device have allowed the calibration of the volume deployed for a few drop sizes. The design for improved tips to be used during the next USML flight is based on these results.

Trinh, E. H.↗
NASA NTRS1994

Solid Surface Wetting and the Deployment of Drops in Microgravity

The complete or partial deployment of liquid samples in low gravity is primarily influenced by the interfacial properties of the specific liquid and solid materials used because the overwhelming bias of the Earth gravitational acceleration is removed. This study addresses the engineering aspects of injecting and deploying drops of prescribed volume into an acoustic positioning chamber in microgravity. The specific problems of interest are the design, testing, and implementation of injector tips to be used in a simuttaneously retracting dual-injector system used in the Drop Physics Module microgravity experiment facility. Prior to release, the liquid to be deployed must be retained within a restricted area at the very end of the injectors even under dynamic stimuli due to continuous injection flow as well as to the stepped motion of the injectors, and the final released drop must have a well determined volume as well as negligible residual linear or angular momentum from the deployment process. The outcome of Earthbased short-duration low gravity experiments had been the selection of two types of injector tips which were flown as back-up parts and were successfully utilized during the USML-1 Spacelab mission. The combination of a larger contact surface, liquid pinning with a sharp edge, and selective coating of strategic tip surfaces with a non-wetting compound has allowed a significant increase in the success rate of deployment of simple and compound drops of aqueous solutions of glycerol and silicone oil. The diameter of the samples studied in the Drop Physics Module ranged between 0.3 and 2.7 cm. The tests conducted onsrbit with a manually operated small device have allowed the calibration of the volume deployed for a few drop sizes. The design for improved tips to be used during the next USML flight is based on these results.

Trinh, E. H.↗
DOE OSTI2020

Taxon-specific microbial growth and mortality patterns reveal distinct temporal population responses to rewetting in a California grassland soil

Abstract Microbial activity increases after rewetting dry soil, resulting in a pulse of carbon mineralization and nutrient availability. The biogeochemical responses to wet-up are reasonably well understood and known to be microbially mediated. Yet, the population level dynamics, and the resulting changes in microbial community patterns, are not well understood as ecological phenomena. Here, we used sequencing of 16S rRNA genes coupled with heavy water (H218O) DNA quantitative stable isotope probing to estimate population-specific rates of growth and mortality in response to a simulated wet-up event in a California annual grassland soil. Bacterial growth and mortality responded rapidly to wet-up, within 3 h, and continued throughout the 168 h incubation, with patterns of sequential growth observed at the phylum level. Of the 37 phyla detected in the prewet community, growth was found in 18 phyla while mortality was measured in 26 phyla. Rapid growth and mortality rates were measurable within 3 h of wet-up but had contrasting characteristics; growth at 3 h was dominated by select taxa within the Proteobacteria and Firmicutes, whereas mortality was taxonomically widespread. Furthermore, across the community, mortality exhibited density-independence, consistent with the indiscriminate shock resulting from dry-down and wet-up, whereas growth was density-dependent, consistent with control by competition or predation. Total aggregated growth across the community was highly correlated with total soil CO2 production. Together, these results illustrate how previously “invisible” population responses can translate quantitatively to emergent observations of ecosystem-scale biogeochemistry.

58 GEOSCIENCES↗
NASA NTRS2007

A Rapid Survey of the Compatibility of Selected Seal Materials with Conventional and Semi-Synthetic JP-8

Since the synthesis of a liquid hydrocarbon fuel from coal by Franz Fischer and Hans Tropsch in 1923, there has been cyclic interest in developing this fuel for military and commercial applications. In recent years the U.S. Department of Defense has taken interest in producing a unified battlespace fuel using the Fischer Tropsch (FT) process for a variety of reasons including cost, quality, and logistics. In the past year there has been a particular emphasis on moving quickly to demonstrate that an FT fuel can be used in the form of a blend with conventional petroleum-derived jet fuel. The initial objective is to employ this semi-synthetic fuel with blend ratios as high as 50 percent FT with longer range goals to use even high blend ratios and ultimately a fully synthetic jet fuel. A significant concern associated with the use of a semi-synthetic jet fuel with high FT blend ratios is the effect these low aromatic fuels will have on fuel-wetted polymeric materials, most notably seals and sealants. These materials typically swell and soften to some degree when exposed to jet fuel and the aromatic content of these fuels contribute to this effect. Semi-synthetic jet fuels with very low aromatic contents may cause seals and sealants to shrink and harden leading to acute or chronic failure. Unfortunately, most of the material qualification tests are more concerned with excessive swelling than shrinkage and there is little guidance offered as to an acceptable level of shrinkage or other changes in physical properties related to low aromatic content. Given the pressing need for guidance data, a program was developed to rapidly survey the volume swell of selected fuel-wetted materials in a range of conventional and semi-synthetic jet fuels and through a statistical analysis to make a determination as to whether there was a basis to be concerned about using fuels with FT blend ratios as high as 50 percent. Concurrent with this analysis data was obtained as to the composition of the fuel absorbed in fuel-wetted materials through the use of GC-MS analysis of swollen samples as well as other supporting data. In this presentation the authors will present a summary of the results of the volume swell and fuel absorbed by selected O-rings and sealants as well as a description of the measurement protocols developed for this program.

Graham, John L.↗
NASA NTRS1991

Scale selection and propagation of wave-CISK with conditional heating

Analytic solutions are derived for simple models of equatorial wave-CISK with conditional (positive-only) heating. Conditional heating favors an unstable mode having a single wet region of infinitesimal width. This result helps explain model simulations of tropical superclusters and intraseasonal oscillations. Mechanisms of scale selection and propagation are discussed, and the model is generalized to include evaporation-wind feedback, multiple vertical-mode CISK, and scale-dependent damping. The first two mechanisms cause zonal propagation, without scale selection. Scale-dependent damping breaks the inviscid continuum (wherein modes exist as a continuous function of wet region width) into discrete modes with unique horizontal structure and phase speed. Results are contrasted with the hierarchy of scales in observed intraseasonal oscillations.

Dunkerton, Timothy J.↗
DOE OSTI2024

Selection of representative general circulation models under climatic uncertainty for Western North America

Abstract Climate change research uses an ensemble of general circulation model runs (GCMs-runs) to predict future climate under uncertainties. To reduce computational costs, this study selects representative GCM-runs (RGCM-runs) for Western North America (WNA) based on their performance in replicating historical climate conditions from 1981 to 2005 and projecting future changes from 1981–2010 to 2071–2100. This evaluation is conducted under two representative concentration pathways (RCPs) scenarios, RCP4.5 and RCP8.5, from the Coupled Model Intercomparison Project 5. By using an envelope-based selection technique and a multi-objective distance-based approach, we identify four RGCM-runs per RCP representing diverse climatic conditions, including wet-warm, wet-cold, dry-warm, and dry-cold. Compared to the full-set, these selected runs show a decreased mean absolute error (MAE) between the reference and RGCM-runs concerning the monthly average mean air temperature (T̄) and precipitation (P̄). For RCP4.5, T̄ MAE is 0.45 (vs. 0.58 in the full-set) and P̄ MAE is 0.31 (vs. 0.42). For RCP8.5, T̄ MAE is 0.51 (vs. 0.75) and P̄ MAE is 0.25 (vs. 0.36). The lower MAE values in the RGCM-run set indicate closer alignment between predicted and reference values, making the RGCM-run suitable for climate impact assessments in the region.

Water Resources↗
DOE OSTI2022

Laser ablation for structuring Li-ion electrodes for fast charging and its impact on material properties, rate capability, Li plating, and wetting

Laser ablation is a scalable technique for decreasing the effective tortuosity of electrodes by selectively removing material with high precision. Applied to ≈ 110 um thick electrode coatings, this work focuses on understanding the impact of laser ablation on electrode material properties at the beginning of life and synergistic impacts of ablated channels on cell performance throughout their cycle life. Post laser ablation, local changes in chemistry, crystallography, and morphology of the laser-impacted electrode regions are investigated. It is shown that femtosecond pulsed laser ablation can achieve high-rate material removal with minor material damage locally at the interface of the impacted zones. The capacity achieved during a 6C (10 min) constant-current constant-voltage charge to 4.2 V improved from 1 mAh cm -2 for the non-ablated electrodes to almost 2 mAh cm -2 for the ablated electrodes. This benefit is attributed to a synergistic effect of enhanced wetting and decreased electrode tortuosity. The benefit was maintained for over 120 cycles, and upon disassembly decreased Li-plating on the graphite anode was observed. Finally, multi-physics modeling in conjunction with wetting analyses showed that laser ablating either one of the electrodes led to substantial improvements in wetting and rate capability, indicating that substantial performance benefits can be achieved by ablating only the graphite anode as apposed to both electrodes.

25 ENERGY STORAGE↗
NASA NTRS1990

Wet atmospheric generation apparatus

The invention described relates to an apparatus for providing a selectively humidified gas to a camera canister containing cameras and film used in space. A source of pressurized gas (leak test gas or motive gas) is selected by a valve, regulated to a desired pressure by a regulator, and routed through an ejector (venturi device). A regulated source of water vapor in the form of steam from a heated reservoir is coupled to a low pressure region of the ejector which mixes with high velocity gas flow through the ejector. This mixture is sampled by a dew point sensor to obtain dew point thereof (ratio of water vapor to gas) and the apparatus adjusted by varying gas pressure or water vapor to provide a mixture at a connector having selected humidity content.

Hamner, Richard M.↗
DOE OSTI2020

Optical fields in porous polylactide matrices

Optical fields induced by laser light inside porous polymer matrices (scaffolds) under stimulating effect on cells are investigated. The spectra of light scattering coefficients and anisotropy factors of porous polylactide scaffolds in the visible and near-IR ranges are determined by numerical simulation based on experimental data obtained using a double integrating sphere. Studies are conducted for dry and wet scaffolds fabricated by supercritical fluid foaming and surface-selective laser sintering. The Monte Carlo method is used to calculate the fluence rate distribution under the assumptions of the Henyey – Greenstein phase scattering function and the model phase function of scattering on spherical cavities. It is shown that th e fluence rate distribution mainly depends on the scattering coefficient and the mean cosine of the deflection angle (g-factor). The results obtained are of great practical importance for tissue engineering based on the use of polymeric porous scaffolds with cells to replace tissue defects; they can be used to determine the dose range for laser stimulation of cells. (paper)

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1981

Synergistic relationships among remote-sensing and geophysical media: Geological and hydrological applications

Skylab photographs, side-looking radar imagery, published soil maps, topographic maps, conventional aerial photography as well as LANDSAT imagery under wet and dry changes for several years were analyzed over selected areas in Minnesota to test their usefulness in detecting near-surface ground water. Results show that optical density read from LANDSAT data is not a reliable discriminator of depth to shallow ground water when one band of one scene is used alone, and is little improved when several bands of several scenes are used synergistically. The method is enhanced if information from soil maps is included in the analysis, especially for discriminating boggy ground from better drained areas. It appears, however, that in areas where soil maps and good topographic maps already exist, the depth to ground water can be predicted from those media as well as (if not better than) it can be predicted from remote imagery. The LANDSAT method used demonstrated no capability for recognizing deeper categories of ground water.

Southwick, D. L.↗
DOE OSTI2022

Catalytic Dehydrogenation of Ethane over Mn Oxide Supported on Zeolite Chabazite

A new class of Mn-containing zeolites prepared by incipient wetness impregnation (IWI) have been found to catalyze the ethane dehydrogenation reaction with high selectivity (98 %+). Preparation by IWI leads to the formation of Mn 2 O 3 nanoparticles on the external surface of the zeolite crystals and herein is shown that the primary active sites for the reaction are located on the surface of these particles. Propane dehydrogenation is also successfully catalyzed by this catalyst. Furthermore, other Mn-zeolites (MFI and BEA) also have high reactivity and selectivity towards light alkane dehydrogenation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1999

Regional Climatology and Surface Radiation Budget

The climatology and surface radiation budget (SRB) of a region are intimately related. This paper presents a brief examination of this relationship. An 8-year surface radiation budget data set has been developed based on satellite measurements. In that data set and in this paper a region is defined as a quasi-square 2.5o in latitude and approximately the same physical distance in longitude. A pilot study by Wilber et al. (1998) showed a variety of behaviors of the annual cycles for selected regions. Selected desert regions form a loop in a specific part of the plot, with large NLW and large NSW. Tropical wet regions form much smaller loops in a different part of the plot, with small NLW and large NSW. For regions selected in high latitude the annual cycles form nearly linear figures in another part of the plot. The question arises as to whether these trajectories are characteristic of the climatology of the region or simply the behavior of the few regions selected from the set of 6596 regions. In order to address this question, it is necessary to classify the climatology of the each region, e.g. as classified by Koeppen (1936) or Trenwarthe and Horne (1980). This paper presents a method of classifying climate of the regions on the basis of the surface radiation behavior such that the results are very similar to the classification of Trenwarthe and Horne. The characteristics of the annual cycle of SRB components can then be investigated further, based on the climate classification of each region.

Wilber, Anne C.↗
DOE OSTI2024

Development of a Sulfur Tolerant CHG Process (CRADA 442) (Final Report)

The Pacific Northwest Laboratory (PNNL) has developed the Catalytic Hydrothermal Gasification (CHG) technology, which can convert low-value organics dispersed in aqueous streams, such as the aqueous phase byproduct from hydrothermal liquefaction (HTL) of wet wastes, to a mixture of methane, H 2 , and CO 2 . The current CHG catalyst, ruthenium (Ru) on a graphite substrate, was selected for its effectiveness as a reducing catalyst. However, the target waste aqueous feedstock, the HTL aqueous phase from wet wastes, such as sewage sludge, contains a fair amount of sulfur in both organic and inorganic forms. Like many other reduced metal catalysts, Ru is deactivated or poisoned by exposure to sulfur, among other contaminants. In general, a deactivated Ru catalyst cannot be reactivated or restored except by removing and returning it for remanufacturing. Therefore, there is an urgent need for a sulfur-resistant catalyst to enable CHG processing of the HTL aqueous waste stream. PNNL, with support from SoCalGas CRADA, has developed a sulfur resistant CHG catalyst and demonstrated a stable CHG process for converting HTL aqueous phases from wet wastes. Here, we report the major accomplishments of the project: • We have demonstrated that sulfided Ru based catalysts is stable during CHG of HTL aqueous waste stream, with a requirement of activity improvement. • We have developed a new catalyst, with 0.5-2 wt.% Ru loading, showing better activity compared to the baseline 6.7 wt.% RuSx/C catalyst. • With the new catalysts, the single-pass COD reduction is approximately 60% and two-pass COD reduction can reach approximately 85%. • The process is robust in terms of being effective across a wide range of organic species in the feedstock. • Techno-economic analysis was conducted to evaluate the economic impact of catalyst advancement and identify further improvement requirements. This type of catalyst shows great potential to be efficient and robust for CHG with low catalyst cost.

03 NATURAL GAS↗
DOE OSTI2020

High-loading single Pt atom sites [Pt-O(OH) x ] catalyze the CO PROX reaction with high activity and selectivity at mild conditions

The preferential oxidation of CO (PROX) in hydrogen-rich fuel gas streams is an attractive option to remove CO while effectively conserving energy and H 2 . However, high CO conversion with concomitant high selectivity to CO 2 but not H 2 O is challenging. Here, we report the synthesis of high-loading single Pt atom (2.0 weight %) catalysts with oxygen-bonded alkaline ions that stabilize the cationic Pt. The synthesis is performed in aqueous solution and achieves high Pt atom loadings in a single-step incipient wetness impregnation of alumina or silica. Promisingly, these catalysts have high CO PROX selectivity even at high CO conversion (~99.8% conversion, 70% selectivity at 110°C) and good stability under reaction conditions. These findings pave the way for the design of highly efficient single-atom catalysts, elucidate the role of –OH species in CO oxidation, and confirm the absence of a support effect for our case.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1974

Effect of gravity on liquid phase sintering

The unique conditions offered by the earth orbital environment in material processing involving both solid and liquid phases, such as liquid phase sintering, were studied. An experimental development program involving both test and theoretical work was initiated. Experimental work using material combinations selected such that maximum information about the effect of gravity can be derived has been conducted. Wetting of the solid phase by the liquid during sintering is an important phenomenon in liquid phase sintering, and gravity has influence on both capillary phenomenon and density segregation; hence, material combinations were selected such that these two effects can be suitably studies. The experimental work is meant to form the basis for similar comparative work done under low-g conditions. The part of the model dealing with the capillary phenomenon, as related to liquid phase sintering and the effect of gravity on it, suggest that gravity will have negligible effect on the Bond number and that the cohesive force is dependent on both the amount of liquid phase and the angle of contact.

Mookherji, T.↗
DOE OSTI2024

Scalable preparation of oxygen carriers for chemical looping

Wet impregnation of active metal precursors into porous substrates, together with selective adsorption of the precursors on the pore surfaces, enables transition metal oxides derived from the precursors to disperse throughout the substrate, even at the nanoscale, without increased sintering or agglomeration, thereby forming oxygen carriers suitable for chemical looping. The porous substrate can be an oxide, for example SiO 2 . The oxygen carriers can comprise relatively large oxide loadings of over about 20 wt % and exhibit high reactivity over many regeneration cycles with substantially no loss in oxygen transport capacity or decrease in kinetics. The use of multiple transition metal oxides, for example NiO in addition to CuO, can greatly enhance chemical looping performance.

O′Malley, Kyle↗
NASA NTRS2004

Selection of an Alternate Biocide for the ISS Internal Thermal Control System Coolant, Phase 2

The ISS (International Space Station) ITCS (Internal Thermal Control System) includes two internal coolant loops that utilize an aqueous based coolant for heat transfer. A silver salt biocide had previously been utilized as an additive in the coolant formulation to control the growth and proliferation of microorganisms within the coolant loops. Ground-based and in-flight testing demonstrated that the silver salt was rapidly depleted, and did not act as an effective long-term biocide. Efforts to select an optimal alternate biocide for the ITCS coolant application have been underway and are now in the final stages. An extensive evaluation of biocides was conducted to down-select to several candidates for test trials and was reported on previously. Criteria for that down-select included: the need for safe, non-intrusive implementation and operation in a functioning system; the ability to control existing planktonic and biofilm residing microorganisms; a negligible impact on system-wetted materials of construction; and a negligible reactivity with existing coolant additives. Candidate testing to provide data for the selection of an optimal alternate biocide is now in the final stages. That testing has included rapid biocide effectiveness screening using Biolog MT2 plates to determine minimum inhibitory concentration (amount that will inhibit visible growth of microorganisms), time kill studies to determine the exposure time required to completely eliminate organism growth, materials compatibility exposure evaluations, coolant compatibility studies, and bench-top simulated coolant testing. This paper reports the current status of the effort to select an alternate biocide for the ISS ITCS coolant. The results of various test results to select the optimal candidate are presented.

Wilson, Mark E.↗
NASA NTRS1980

Application of composite materials to turbofan engine fan exit guide vanes

A program was conducted by NASA with the JT9D engine manufacturer to develop a lightweight, cost effective, composite material fan exit guide vane design having satisfactory structural durability for commerical engine use. Based on the results of a previous company supported program, eight graphite/epoxy and graphite-glass/epoxy guide vane designs were evaluated and four were selected for fabrication and testing. Two commercial fabricators each fabricated 13 vanes. Fatigue tests were used to qualify the selected design configurations under nominally dry, 38 C (100 F) and fully wet and 60 C (140 F) environmental conditions. Cost estimates for a production rate of 1000 vanes per month ranged from 1.7 to 2.6 times the cost of an all aluminum vane. This cost is 50 to 80 percent less than the initial program target cost ratio which was 3 times the cost of an aluminum vane. Application to the JT9D commercial engine is projected to provide a weight savings of 236 N (53 lb) per engine.

Smith, G. T.↗