SEARCH · Engineering Papers

Results for “Selection pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1997

A Comparison of Pressure Measurements Between a Full-Scale and a 1/16-Scale F/A-18 Twin Tail During Buffet

In 1993, tail buffet tests were performed on a full-scale, production model F/A-18 in the 80-by-120 Foot Wind Tunnel at NASA Ames Research Center. Steady and unsteady pressures were recorded on both sides of the starboard vertical tail for an angle of attack range of 20 to 40 degrees and at a sideslip range of -16 to 16 degrees at freestream velocities up to 100 knots (Mach 0.15, Reynolds number 1.23 x 10(exp 7)). The aircraft was equipped with removable leading edge extension (LEX) fences that are used in flight to reduce tail buffet loads. In 1995, tail buffet tests were performed on a 1/6-scale F-18 A/B model in the Transonic Dynamics Tunnel (TDT) at NASA Langley Research Center. Steady and unsteady pressures were recorded on both sides of both vertical tails for an angle-of-attack range of 7 to 37 degrees at freestream velocities up to 65 knots (Mach 0.10). Comparisons of steady and unsteady pressures and root bending moments are presented for these wind-tunnel models for selected test cases. Representative pressure and root bending moment power spectra are also discussed, as are selected pressure cross-spectral densities.

Moses, Robert W.↗

NASA NTRS1978

Some flow phenomena in a constant area duct with a Borda type inlet including the critical region

Mass limiting flow characteristics for a 55 L/D tube with a Borda type inlet were assessed over large ranges of temperature and pressure, using fluid nitrogen. Under certain conditions, separation and pressure drop at the inlet was sufficiently strong to permit partial vaporization and the remaining fluid flowed through the tube as if it were a free jet. An empirical relation was determined which defines conditions under which this type of flow can occur. A flow coefficient is presented which enables estimations of flow rates over the experimental range. A flow rate stagnation pressure map for selected stagnation isotherms and pressure profiles document these flow phenomena.

Hendricks, R. C.↗

NASA NTRS1978

Some flow phenomena in a constant area duct with a Borda type inlet including the critical region

Mass limiting flow characteristics for a 55 L/D tube with a Borda type inlet have been assessed over large ranges of temperature and pressure using fluid nitrogen. Under certain conditions, separation and pressure drop at the inlet was sufficiently strong to permit partial vaporization and the remaining fluid flowed through the tube as if it were a free jet. An empirical relation was determined which defines conditions under which this type of flow can occur. A flow coefficient is presented which enables one to estimate flow rates over the experimental range. A flow rate stagnation pressure map for selected stagnation isotherms and pressure profiles document these flow phenomena.

Hendricks, R. C.↗

NASA NTRS1981

Penumatic-power supply

Portable compressed air supply has two or more outputs at pressures from 20 to 100 psi. Applications include operating production equipment, spraying paint and lubricants, and pressurizing refrigeration systems. Supply filters air from standard high-pressure line, reduces it to working pressure, and adds lubricant when required. Regulator supplies low-pressure air to output channels. On channel lines, vernier-control valves select output pressures.

Kramer, R. C.↗

NASA NTRS2017

Independent Assessment of the Backshell Pressure Field for Mars Entry, Descent, and Landing Instrumentation 2 (MEDLI2)

The Mars Entry, Descent, and Landing Instrumentation 2 (MEDLI2) project requested that the NASA Engineering and Safety Center (NESC) support a ballistic range test to measure backshell pressures on scale models of the Mars 2020 entry capsule. The MEDLI2 project needed the test to provide important dynamic pressure data to help select a backshell pressure port, quantify drag coefficient reconstruction uncertainties, and design the data acquisition hardware. This document contains the outcome of the NESC assessment.

Prince, Jill L.↗

NASA NTRS2008

Implications of Operational Pressure on CSSE PGS Design

The Constellation Spacesuit Element (CSSE) was required to support crew survival (CS); launch, entry, and abort (LEA) scenarios; zero gravity (0-g) extravehicular activity (EVA) (both unscheduled and contingency); and planetary EVA. Operation of the CSSE in all of these capacities required a pressure garment subsystem (PGS) that would operate efficiently through various pressure profiles. The PGS team initiated a study to determine the appropriate operational pressure profile of the CSSE and how this selection would affect the design of the CSSE PGS. This study included an extensive review of historical PGS operational pressure selection and the operational effects of those pressures, the presentation of four possible pressure paradigm options for use by the CSSE, the risks and design impacts of these options, and the down-selected pressure option.

Lee, Ryan↗

NASA NTRS1983

Dynamic mechanical characterization of cure of a polyimide-graphite fiber composite (PMR 15/Celion 6000)

Dynamic mechanical studies of thermosetting PMR 15 polyimide/Celion 6000 composites were used to characterize cure behavior. Variation in composite shear modulus with cure time for laminates partially cured under 3.45 MPa pressure was compared with that of laminates fully cured under pressure to select a partially cured system whose behavior corresponded with that of the pressure-cured composites. An empirical kinetic model was developed that relates relative composite shear moduli to cure time and temperature. This model, coupled with standard statistical techniques, was used in the determination of an overall activation energy, E = 145 kj/mole (35 kcal/mole) and order of reaction, n, for the cure reaction(s). The empirical relationship defining dynamic modulus as a function of time and temperature remained linear well into the glassy region. Changes in dynamic glass-transition temperature and in the breadth of the transition peaks with cure time are discussed. Shear modulus and damping were found to be more sensitive measures of relative extent of cure than Fourier transform infrared spectroscopy.

Hurwitz, F. I.↗

NASA NTRS1972

Examination of two methods of describing the thermodynamic properties of oxygen near the critical point

A computer study was conducted to compare the numerical behavior of two approaches to describing the thermodynamic properties of oxygen near the critical point. Data on the relative differences between values of specific heats at constant pressure (sub p) density, and isotherm and isochor derivatives of the equation of state are presented for selected supercritical pressures at temperatures in the range 100 to 300 K. The results of a more detailed study of the sub p representations afforded by the two methods are also presented.

Rees, T. H.↗

NASA NTRS1993

Jet-induced ground effects on a parametric flat-plate model in hover

The jet-induced forces generated on short takeoff and vertical landing (STOVL) aircraft when in close proximity to the ground can have a significant effect on aircraft performance. Therefore, accurate predictions of these aerodynamic characteristics are highly desirable. Empirical procedures for estimating jet-induced forces during the vertical/short takeoff and landing (V/STOL) portions of the flight envelope are currently limited in accuracy. The jet-induced force data presented significantly add to the current STOVL configurations data base. Further development of empirical prediction methods for jet-induced forces, to provide more configuration diversity and improved overall accuracy, depends on the viability of this STOVL data base. The data base may also be used to validate computational fluid dynamics (CFD) analysis codes. The hover data obtained at the NASA Ames Jet Calibration and Hover Test (JCAHT) facility for a parametric flat-plate model is presented. The model tested was designed to allow variations in the planform aspect ratio, number of jets, nozzle shape, and jet location. There were 31 different planform/nozzle configurations tested. Each configuration had numerous pressure taps installed to measure the pressures on the undersurface of the model. All pressure data along with the balance jet-induced lift and pitching-moment increments are tabulated. For selected runs, pressure data are presented in the form of contour plots that show lines of constant pressure coefficient on the model undersurface. Nozzle-thrust calibrations and jet flow-pressure survey information are also provided.

Wardwell, Douglas A.↗

NASA NTRS1993

An automated pressure data acquisition system for evaluation of pressure sensitive paint chemistries

An automated pressure data acquisition system for testing of pressure sensitive phosphorescent paints was designed, assembled, and tested. The purpose of the calibration system is the evaluation and selection of pressure sensitive paint chemistries that could be used to obtain global aerodynamic pressure distribution measurements. The test apparatus and setup used for pressure sensitive paint characterizations is described. The pressure calibrations, thermal sensitivity effects, and photodegradation properties are discussed.

Sealey, Bradley S.↗

NASA NTRS1981

Model aerodynamic test results for two variable cycle engine coannular exhaust systems at simulated takeoff and cruise conditions. Comprehensive data report. Volume 3: Graphical data book 1

A graphical presentation of the aerodynamic data acquired during coannular nozzle performance wind tunnel tests is given. The graphical data consist of plots of nozzle gross thrust coefficient, fan nozzle discharge coefficient, and primary nozzle discharge coefficient. Normalized model component static pressure distributions are presented as a function of primary total pressure, fan total pressure, and ambient static pressure for selected operating conditions. In addition, the supersonic cruise configuration data include plots of nozzle efficiency and secondary-to-fan total pressure pumping characteristics. Supersonic and subsonic cruise data are given.

Nelson, D. P.↗

NASA NTRS1995

Double-Knudsen-Cell Apparatus Measures Alloy-Component Activities

Double-Knudsen-cell apparatus provides molecular beam from selected one of two Knudsen cells. Both cells maintained at same temperature. Molecular beam directed into mass spectrometer for measurement of vapor pressure of selected material component. Designed to minimize undesired thermal gradients, provides appropriate translation to place selected cell in position for sampling, and minimizes mixing of molecular beams from cells.

Jacobson, Nathan S.↗

NASA NTRS1974

On-line calibration of high-response pressure transducers during jet-engine testing

Current jet engine testing is concerned with the effect of inlet pressure and temperature distortions on engine performance and involves the use of numerous miniature pressure transducers. Despite recent improvements in the manufacture of miniature pressure transducers, they still exhibit sensitivity change and zero shift with temperature and time. To obtain meaningful data, a calibration system is needed to determine these changes. A system has been developed which provides for computer selection of appropriate reference pressures selected from nine different sources to provide a two- or three-point calibration. Calibrations are made on command, before and sometimes after each data point. A unique 'no leak' matrix valve design is used in the reference-pressure system. Zero-shift corrections are measured and the values are automatically inserted into the data reduction program.

Armentrout, E. C.↗

NASA NTRS1974

On-line calibration of high-response pressure transducers during jet-engine testing

Jet engine testing is reported concerned with the effect of inlet pressure and temperature distortions on engine performance and involves the use of numerous miniature pressure transducers. Despite recent improvements in the manufacture of miniature pressure transducers, they still exhibit sensitivity change and zero-shift with temperature and time. To obtain meaningful data, a calibration system is needed to determine these changes. A system has been developed which provides for computer selection of appropriate reference pressures selected from nine different sources to provide a two- or three-point calibration. Calibrations are made on command, before and sometimes after each data point. A unique no leak matrix valve design is used in the reference pressure system. Zero-shift corrections are measured and the values are automatically inserted into the data reduction program.

Armentrout, E. C.↗

NASA NTRS2023

Development of an Ultra High-Pressure Metals Promoted Combustion in Oxygen Test Apparatus

Materials flammability data is needed at pressures higher than ever tested before (greater than 10,000 psi). WSTF has designed and is currently building a metals flammability apparatus that can test metals up to 30,000 psi. Solid progress was achieved on the chamber in terms of system build up and fulfilling requirements to perform a NASA Test Readiness Review. Understanding metals flammability data at extreme pressure opens the doors for higher pressure and higher performance oxygen systems. Proposed systems include more reliable/higher performance propulsion systems and more reliable/lighter Environmental Control Life Support Systems (ECLSS). The test system needed for this testing required significant research and development to select a pressurization method and eliminate contact with potentially flammable materials back to the chamber. No additional promoted combustion data was collected in FY21. This International Research & Development (IRAD) proposal was critical to getting the system very close to operational status. This capability is critical to collect forward leaning material flammability data for future spacecraft and ground systems. Forward work has been identified and funding is being sought outside of the Center Innovation Fund (CIF) process for late FY23/FY24.

promoted combustion↗

NASA NTRS1990

Optimization of the propulsion cycles for advanced shuttles. II - Performance model methodology

In 1988 computer codes from NASA and DLR were combined to analyze and optimize rocket engines for advance launch vehicles. Further effort has addressed performance propulsion parameters such as chamber pressure, cycle selection (including mixed and tripropellant cycles), nozzle extension, and new technologies. Results of the study indicate that lower dry masses can be reached with the staged combustion cycle than with the gas-generator cycle, using oxygen/hydrogen at relatively high mixture ratio (7:1) and modest chamber pressure (220 bar). For low dry masses the staged combustion cycle is only excelled by the dual-expander cycle using hydrogen and propane as fuels. The emphasis here is to explain the procedure and boundary conditions used for the analysis and the variety of configurations treated, as well as to demonstrate the methods used by presenting some of the major results.

Manski, Detlef↗

NASA NTRS1971

Determination of normal-shock position in a mixed compression supersonic inlet

Methods of determining inlet normal shock position from wall static pressure profiles were investigated. By using methods investigated in this report, it should be possible to control an inlet with less stability margin. Variation in inlet angle-of-attack caused drastic changes in pressure profile shape and wide variations in the angle of the shock plane with respect to the inlet axis. Thus, four sensors located around the circumference may be required to handle angle-of-attack and sideslip variations. One criterion would determine the shock position by comparing individual statics to a properly selected reference pressure.

Dustin, M. O.↗

NASA NTRS1991

Welding space vacuum technology

The objective was to assist the EH 42 Division in putting together a vacuum system that could attain the desired pressure and be large enough to accommodate the gas-metal arc (GMA) welding fixture apparatus. A major accomplishment was the design and fabrication of the controller/annunciator for the 4' by 8' system. It contains many safety features such as thermocouple set point relays that will only allow inlet and exit gas and vacuum valves to be operated at pre-selected system pressures, and a fail safe mode for power interruptions and operator mistakes. It is felt that significant progress was made in this research effort to weld in a vacuum environment. With continued efforts to increase the pump speeds for vacuum chambers and further studies on weld fixtures and gas inlet pressures, the NASA program will be successful.

Johnson, R. Barry↗