Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SULFURIC ACID”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Sulfuric acid cloud interpretation of the infrared spectrum of Venus

Sulfuric acid single-cloud models are compared with the Venus spectrum in the 8-14 micron region. The results indicate that a cloud composed of a 75 percent H2SO4 solution and with a particle density of 100 per cu cm is in good agreement with observations. In addition to explaining the 11.2 micron absorption, this model also predicts an absorption feature at 16.7 microns which should be detectable if the observation is made from an aircraft.

Martonchik, J. V.↗

Uptake of formaldehyde by sulfuric acid solutions - Impact on stratospheric ozone

The study investigates the uptake of CH2O by low temperature sulfuric acid solutions representative of global stratospheric particulate. It is argued that if similar uptake occurs under stratospheric pressures of CH2O, i.e., 1000 times lower than used in the present study, then the removal of CH2O from the gas phase can take away a significant source of odd hydrogen in the mid- and high-latitude lower stratosphere. It is shown that with the inclusion of this reaction, concentrations of OH and H2O are reduced by as much as 4 percent under background levels of aerosols and more than 15 percent under elevated (volcanic) conditions. The accumulation of CH2O in stratospheric aerosols over a season, reaching about 1 M solutions, will alter the composition and may even change the reactivity of these sulfuric acid-water mixtures.

Tolbert, Margaret A.↗

Laboratory measurements of heterogeneous reactions on sulfuric acid surfaces

Increasing evidence from field, modeling, and laboratory studies suggests that heterogeneous reactions on stratospheric sulfate aerosol particles may contribute to global ozone depletion. Using a Knudsen cell reactor technique, the authors have studied the uptake, reactivity, and solubility of several trace atmospheric species on cold sulfuric acid surfaces representative of stratospheric aerosol particles. The results suggest that the heterogeneous conversion of N2O5 to HNO3 is fast enough to significantly affect the partitioning of nitrogen species in the global stratosphere and thus contribute to global ozone depletion. The hydrolysis of ClONO2 is slower and unlikely to be important under normal conditions at midlatitudes. The solubilities of HCl and HNO3 in sulfuric acid down to 200 K were found to be quite low. For HCl, this means that little HCl is available for reaction on the surfaces of stratospheric sulfate aerosol particles. The low solubility of HNO3 means that this product of heterogeneous reactions will enter the gas phase, and the denitrification observed in polar regions is unlikely to occur in the global stratosphere.

Williams, Leah R.↗

Modeling of growth and evaporation effects on the extinction of 1.0-micron solar radiation traversing stratospheric sulfuric acid aerosols

The effects of growth and evaporation of stratospheric sulfuric acid aerosols on the extinction of solar radiation traversing such an aerosol medium are reported for the case of 1.0-micron solar radiation. Modeling results show that aerosol extinction is not very sensitive to the change of ambient water vapor concentration, but is sensitive to ambient temperature changes, especially at low ambient temperatures and high ambient water vapor concentration. A clarification is given of the effects of initial aerosol size distribution and composition on the change of aerosol extinction due to growth and evaporation processes. It is shown that experiments designed to observe solar radiation extinction of aerosols may also be applied to the determination of observed changes in aerosol optical properties, environmental parameters, or the physical and optical characteristics of sulfate aerosols.

Yue, G. K.↗

Sulfuric Acid and Soot Particle Formation in Aircraft Exhaust

A combination of CN counts, Ames wire impactor size analyses and optical particle counter data in aircraft exhaust results in a continuous particle size distribution between 0.01 micrometer and 1 micrometer particle radius sampled in the exhaust of a Boeing 757 research aircraft. The two orders of magnitude size range covered by the measurements correspond to 6-7 orders of magnitude particle concentration. CN counts and small particle wire impactor data determine a nucleation mode, composed of aircraft-emitted sulfuric acid aerosol, that contributes between 62% and 85% to the total aerosol surface area and between 31% and 34% to its volume. Soot aerosol comprises 0.5% of the surface area of the sulfuric acid aerosol. Emission indices are: EIH2SO4 = 0.05 g/kgFUEL and (0.2-0.5) g/kgFUEL (for 75 ppmm and 675 ppmm fuel-S, respectively), 2.5E4<EISOOT<1.3E-3 g/kgFUEL, and EICN 8E14 and 1.3E16 particles/kgFUEL (for 75 and 675 ppmm fuel-S). The sulfur (gas) to H2SO4 (particle) conversion efficiency is between 10% and 25%.

Pueschel, Rudolf F.↗

A dynamic parameterization of sulfuric acid–dimethylamine nucleation and its application in three-dimensional modeling

Sulfuric acid (SA) is a governing gaseous precursor for atmospheric new particle formation (NPF), a major source of global ultrafine particles, in environments studied around the world. In polluted urban atmospheres with high condensation sinks (CSs), the formation of stable SA–amine clusters, such as SA–dimethylamine (DMA) clusters, usually initializes intense NPF events. Coagulation scavenging and cluster evaporation are dominant sink processes of SA–amine clusters in urban atmospheres, yet these loss processes are not quantitatively included in the present parameterizations of SA–amine nucleation. We herein report a parameterization of SA–DMA nucleation, based on cluster dynamic simulations and quantum chemistry calculations, with certain simplifications to greatly reduce the computational costs. Compared with previous SA–DMA nucleation parameterizations, this new parameterization was able to reproduce the dependences of particle formation rates on temperature and CSs. We then incorporated it in a three-dimensional (3-D) chemical transport model to simulate the evolution of the particle number size distributions. Simulation results showed good consistency with the observations in the occurrence of NPF events and particle number size distributions in wintertime Beijing and represented a significant improvement compared to that using a parameterization without coagulation scavenging. Quantitative analysis shows that SA–DMA nucleation contributes significantly to nucleation rates and aerosol population during the 3-D simulations in Beijing (>99 % and >60 %, respectively). These results broaden the understanding of NPF in urban atmospheres and stress the necessity of including the effects of coagulation scavenging and cluster stability in simulating SA–DMA nucleation in 3-D simulations. Representing these processes is thus likely to improve model performance in particle source apportionment and quantification of aerosol effects on air quality, human health, and climate.

Li, Yuyang↗

Structure of Sulfuric Acid Solutions Using Pair Distribution Function Analysis

Solvation and mesoscale ordering of sulfuric acid and other strong acid solutions leads to suppressed freezing points and strong rheological changes with varying concentration. While the solid-state structures are well-understood, studies focused on the evolving solvation structure in the solution phase have probed a limited concentration range (~1–6 M). This study applies a total scattering approach in both the wide-angle X-ray scattering (WAXS) and pair distribution function (PDF) regimes to elucidate the evolving solvation structure over its full range of acid concentration (0–18 M). The emergence of a prepeak in the WAXS regime at intermediate concentrations indicates a transition from noninteracting sulfate molecules in the dilute limit to sterically limited sulfates at concentrations near its deep eutectic point. Fits to the PDF data quantify this trend, showing a transition from octahedrally hydrated sulfates up to 6–7 M concentrations, followed by gradual dehydration, and eventually reaching a solution structure similar to that of water-in-salt electrolyte systems at high acid concentrations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Interaction of Ethyl Alcohol Vapor with Sulfuric Acid Solutions

We investigated the uptake of ethyl alcohol (ethanol) vapor by sulfuric acid solutions over the range approx.40 to approx.80 wt % H2SO4 and temperatures of 193-273 K. Laboratory studies used a fast flow-tube reactor coupled to an electron-impact ionization mass spectrometer for detection of ethanol and reaction products. The uptake coefficients ((gamma)) were measured and found to vary from 0.019 to 0.072, depending upon the acid composition and temperature. At concentrations greater than approx.70 wt % and in dilute solutions colder than 220 K, the values approached approx.0.07. We also determined the effective solubility constant of ethanol in approx.40 wt % H2SO4 in the temperature range 203-223 K. The potential implications to the budget of ethanol in the global troposphere are briefly discussed.

sulfate aerosols↗

Friction and wear of nickel in sulfuric acid

Experiments were conducted with elemental nickel sliding on aluminum oxide in aerated sulfuric acid in concentrations ranging from very dilute (10 -4 N, i.e., 5 ppm) to very concentrated (96 percent) acid. Load and reciprocating sliding speeds were kept constant. With the most dilute concentration (10 -4 N) no observable corrosion occurred in or outside the wear area. This was used as the base condition to determine the high contribution of corrosion to total wear loss at acid concentrations between 0.5 percent (0.1 N) and 75 percent. Corrosion reached a maximum rate of 100 millimeters per year at 30 percent acid. At the same time, general corrosion outside the wear area was very low, in agreement with published information. It is clear that friction and wear greatly accelerated corrosion in the wear area. At dilute concentrations of 0.001 and 0.01 N, corrosion in the wear area was low, and general corrosion outside was also low, but local outside regions in the direction of the wear motion experienced some enhanced corrosion, apparently due to fluid motion of the acid.

Rengstorff, G. W. P.↗

Stratospheric sulfuric acid fraction and mass estimate for the 1982 volcanic eruption of El Chichon

The stratospheric sulfuric acid fraction and mass for the 1982 volcanic eruptions of El Chichon are investigated using data from balloon soundings at Laramie (41 deg N) and in southern Texas (27-29 deg N). The total stratospheric mass of these eruptions is estimated to be approximately 8 Tg about 6.5 months after the eruption with possibly as much as 20 Tg in the stratosphere about 45 days after the eruption. Observations of the aerosol in Texas revealed two primary layers, both highly volatile at 150 C. Aerosol in the upper layer at about 25 km was composed of an approximately 80 percent H2SO4 solution while the lower layer at approximately 18 km was composed of a 60-65 percent H2SO4 solution aerosol. It is calculated that an H2SO4 vapor concentration of at least 3 x 10 to the 7th molecules/cu cm is needed to sustain the large droplets in the upper layer. An early bi-modal nature in the size distribution indicates droplet nucleation from the gas phase during the first 3 months, while the similarity of the large particle profiles 2 months apart shows continued particle growth 6.5 months after the explosion.

Hofmann, D. J.↗

Delayed production of sulfuric acid condensation nuclei in the polar stratosphere from El Chichon volcanic vapors

It is pointed out that measurements of the vertical profiles of atmospheric condensation nuclei (CN) have been conducted since 1973. Studies with a new instrument revealed that the CN concentration undergoes a remarkable annual variation in the 30-km region characterized by a large increase in the late winter/early spring period with a subsequent decay during the remainder of the year. The event particles are observed to be volatile at 150 C, suggesting a sulfuric acid-water composition similar to that found in the normal 20 km aerosol layer. The development of about 10 to the 7th metric tons of sulfuric acid aerosol following the injection of sulfurous gases by El Chichon in April 1982, prompted Hofmann and Rosen (1983) to predict a very large CN event for 1983. The present investigation is concerned with the actual observation of the predicted event. Attention is given to the observation of a very large increase of what appear to be small sulfuric acid droplets at 30-km altitude in January 1983 over Laramie, WY, in January 1983.

Hofmann, D. J.↗

Cluster-dynamics-based parameterization for sulfuric acid–dimethylamine nucleation: comparison and selection through box and three-dimensional modeling

Clustering of gaseous sulfuric acid (SA) enhanced by dimethylamine (DMA) is a major mechanism for new particle formation (NPF) in polluted atmospheres. However, uncertainty remains regarding the SA–DMA nucleation parameterization that reasonably represents cluster dynamics and is applicable across various atmospheric conditions. This uncertainty hinders accurate three-dimensional (3-D) modeling of NPF and the subsequent assessment of its environmental and climatic impacts. Here we extensively compare different cluster-dynamics-based parameterizations for SA–DMA nucleation and identify the most reliable one through a combination of box model simulations, 3-D modeling, and in situ observations. Results show that the parameterization derived from Atmospheric Cluster Dynamic Code (ACDC) simulations, incorporating the latest theoretical insights (DLPNO-CCSD(T)/aug-cc-pVTZ//ωB97X-D/6-311++G(3df,3pd) level of theory) and adequate representation of cluster dynamics, exhibits dependable performance in 3-D NPF simulation for both winter and summer conditions in Beijing and shows promise for application in diverse atmospheric conditions. Another ACDC-derived parameterization, replacing the level of theory with RI-CC2/aug-cc-pV(T+d)Z//M06-2X/6–311++G(3df,3pd), also performs well in NPF modeling at relatively low temperatures around 280 K but exhibits limitations at higher temperatures due to inappropriate representation of SA–DMA cluster thermodynamics. Additionally, a previously reported parameterization incorporating simplifications is applicable for simulating NPF in polluted atmospheres but tends to overestimate particle formation rates under conditions of elevated temperature (>∼300 K) and low-condensation sink (<∼3×10 -3 s −1 ). Our findings highlight the applicability of the new ACDC-derived parameterization, which couples the latest SA–DMA nucleation theory and holistic cluster dynamics, in 3-D NPF modeling. The ACDC-derived parameterization framework provides a valuable reference for developing parameterizations for other nucleation systems.

Shen, Jiewen↗

Laboratory measurement of the millimeter wave properties of liquid sulfuric acid (H2SO4)

The methodology and the results of laboratory measurements of the millimeter wave properties of liquid sulfuric acid are presented. Measurements conducted at 30-40 and 90-100 GHz are reported, using different concentrations of liquid H2SO4. The measured data are used to compute the expected opacity of H2SO4 condensates and their effects on the millimeter wave emission from Venus. The cloud condensate is found to have an effect on the emission from Venus. The calculated decrease in brightness temperature is well below the observed decrease in brightness temperature found by de Pater et al. (1991). It is suggested that other constituents such as gaseous H2SO4 also affect the observed variation in the brightness temperature.

Fahd, Antoine K.↗

Monitoring Sulfuric Acid and Temperature Using Raman Spectroscopy and Multivariate Chemometrics

Multivariate regression models were optimized for the quantification of sulfuric acid (H 2 SO 4 ) [0–8 M] and temperature (20 °C–80 °C) in the presence of ammonium sulfate ((NH 4 ) 2 SO 4 [0–0.6 M]) using Raman spectroscopy. Optical vibrational spectroscopy is a useful nondestructive technique for the in situ analysis of complex chemical systems notoriously difficult to monitor in situ and in real-time. Multivariate analysis, a chemometrics method, can be paired with these nondestructive optical methods for determining analyte concentration and speciation in complex solutions, such as dissociated species in polyprotic acids, e.g., H 2 SO 4 . The effect of temperature is often overlooked although it can have a major influence on speciation and the corresponding Raman spectra. Here, in this study, partial least squares regression models were optimized for the quantification of H 2 SO 4 and its two deprotonated forms as a function of temperature. Measuring bisulfate as a function of temperature is particularly challenging owing to changes in the second dissociation constant. A designed training set effectively minimized the sample set size and trained a robust predictive model with percent root mean square error of <3% for H 2 SO 4 . The practical strategy employed here was demonstrated to be effective for building chemometric models that directly account for dynamic temperatures with static samples and is shown to be amenable to flow cell analysis applications with a simple calibration transfer for process monitoring applications.

D-optimal design↗

Heat-Exchange Fluids for Sulfuric Acid Vaporizers

Some fluorine-substituted organic materials meet criteria for heat-exchange fluids in contact with sulfuric acid. Most promising of these are perfluoropropylene oxide polymers with degree of polymerization (DP) between 10 and 50. It is desirable to have DP in high range because vapor pressure of material decreases as DP increases, and high-DP liquids have lower loss due to vaporization.

Lawson, D. D.↗

Distribution of Hydrogen Peroxide, Carbon Dioxide, and Sulfuric Acid in Europa's Icy Crust

Galileo's Near Infrared Mapping Spectrometer (NIMS) detected hydrogen peroxide, carbon dioxide and a hydrated material on Europa's surface, the latter interpreted as hydrated sulfuric acid (H2SO4*nH2O) or hydrated salts. Related compounds are molecular oxygen, sulfur dioxide, and two chromophores, one that is dark in the ultraviolet(UV) and concentrated on the trailing side, the other brighter in the UV and preferentially distributed in the leading hemisphere. The UV-dark material has been suggested to be sulfur.

Carlson, R. W.↗