Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SPACECRAFT MODEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Mathematical crew motion disturbance models for spacecraft control system design

Several techniques for modeling the disturbances to a spacecraft's attitude caused by moving crew members are presented. These disturbances can be the largest moments acting on a manned spacecraft, and knowledge of their effect is important in the sizing, design, and analysis/simulation of spacecraft attitude control systems. The modeling techniques are identified as two principal types: deterministic and stochastic. Three techniques of each type are presented. The deterministic models include point-mass motion derivatives and a discussion on dynamic models of moving crew members. The stochastic techniques are highlighted by a Fourier transform method and the representation of long-term crew disturbance activities as outputs from appropriately designed filters. A z-transform technique is developed to obtain a difference-equation form of stochastic models for use on digital computers. An appendix derives spacecraft equations of motion which can be used with many of the models discussed.

Conway, B. A.↗
NASA NTRS1997

Empirical models for spacecraft damage from orbital debris penetration and effects on spacecraft survivability

Semi-empirical models of hole diameter and tip-to-tip crack length for different multi-wall shielding systems currently under development for the International Space Station are presented. These equations were developed using light gas gun test data at impact velocities of 6.5 km/s and inhibited shaped charge test data for an impact velocity of 11.3 km/s. These models are incorporated into a survivability analysis using the manned spacecraft crew survivability computer code to determine whether or not module unzipping or crew incapacitation would occur under a specific set of impact conditions.

Williamsen, Joel↗
NASA NTRS2018

Comparing Free-Free and Shaker Table Model Correlation Methods Using Jim Beam

Finite element model correlation as part of a spacecraft program has always been a challenge. For any NASA mission, the coupled system response of the spacecraft and launch vehicle can be determined analytically through a Coupled Loads Analysis (CLA), as it is not possible to test the spacecraft and launch vehicle coupled system before launch. The value of the CLA is highly dependent on the accuracy of the frequencies and mode shapes extracted from the spacecraft model. NASA standards require the spacecraft model used in the final Verification Loads Cycle to be correlated by either a modal test or by comparison of the model with Frequency Response Functions (FRFs) obtained during the environmental qualification test. Due to budgetary and time constraints, most programs opt to correlate the spacecraft dynamic model during the environmental qualification test, conducted on a large shaker table. For any model correlation effort, the key has always been finding a proper definition of the boundary conditions. This paper is a correlation case study to investigate the difference in responses of a simple structure using a free-free boundary, a fixed boundary on the shaker table, and a base-drive vibration test, all using identical instrumentation. The NAVCON Jim Beam test structure, featured in the IMAC round robin modal test of 2009, was selected as a simple, well recognized and well characterized structure to conduct this investigation. First, a free-free impact modal test of the Jim Beam was done as an experimental control. Second, the Jim Beam was mounted to a large 20,000 lbf shaker, and an impact modal test in this fixed configuration was conducted. Lastly, a vibration test of the Jim Beam was conducted on the shaker table. The free-free impact test, the fixed impact test, and the base-drive test were used to assess the effect of the shaker modes, evaluate the validity of fixed-base modeling assumptions, and compare final model correlation results between these boundary conditions.

Modal Test↗
NASA NTRS1972

A stochastic bioburden model for spacecraft sterilization.

Development of a stochastic model of the probability distribution for the random variable representing the number of microorganisms on a surface as a function of time. The first basic principle associated with bioburden estimation is that viable particles are removed from surfaces. The second notion important to the analysis is that microorganisms in environments and on surfaces occur in clumps. The last basic principle relating to bioburden modeling is that viable particles are deposited on a surface. The bioburden on a spacecraft is determined by the amount and kind of control exercised on the spacecraft assembly location, the shedding characteristics of the individuals in the vicinity of the spacecraft, its orientation, the geographical location in which the assembly takes place, and the steps in the assembly procedure. The model presented has many of the features which are desirable for its use in the spacecraft sterilization programs currently being planned by NASA.

Roark, A. L.↗
NASA NTRS1979

Spacecraft charging modeling development and validation study

The effects of spacecraft charging are presented. Analytical models of the magnetospheric environment are used to show the charging interaction between the spacecraft and the plasma sheath, the discharge phenomena, and electromagnetic coupling from the discharge to spacecraft components. Ground tests to validate the models are described.

Odonnell, E. E.↗
NASA NTRS1996

First principles nickel-cadmium and nickel hydrogen spacecraft battery models

The principles of Nickel-Cadmium and Nickel-Hydrogen spacecraft battery models are discussed. The Ni-Cd battery model includes two phase positive electrode and its predictions are very close to actual data. But the Ni-H2 battery model predictions (without the two phase positive electrode) are unacceptable even though the model is operational. Both models run on UNIX and Macintosh computers.

Timmerman, P.↗
NASA NTRS2013

Estimation Model of Spacecraft Parameters and Cost Based on a Statistical Analysis of COMPASS Designs

The Collaborative Modeling for Parametric Assessment of Space Systems (COMPASS) team at Glenn Research Center has performed integrated system analysis of conceptual spacecraft mission designs since 2006 using a multidisciplinary concurrent engineering process. The set of completed designs was archived in a database, to allow for the study of relationships between design parameters. Although COMPASS uses a parametric spacecraft costing model, this research investigated the possibility of using a top-down approach to rapidly estimate the overall vehicle costs. This paper presents the relationships between significant design variables, including breakdowns of dry mass, wet mass, and cost. It also develops a model for a broad estimate of these parameters through basic mission characteristics, including the target location distance, the payload mass, the duration, the delta-v requirement, and the type of mission, propulsion, and electrical power. Finally, this paper examines the accuracy of this model in regards to past COMPASS designs, with an assessment of outlying spacecraft, and compares the results to historical data of completed NASA missions.

cost modeling↗
NASA NTRS2009

Integrated Modeling of Spacecraft Touch-and-Go Sampling

An integrated modeling tool has been developed to include multi-body dynamics, orbital dynamics, and touch-and-go dynamics for spacecraft covering three types of end-effectors: a sticky pad, a brush-wheel sampler, and a pellet gun. Several multi-body models of a free-flying spacecraft with a multi-link manipulator driving these end-effectors have been tested with typical contact conditions arising when the manipulator arm is to sample the surface of an asteroidal body. The test data have been infused directly into the dynamics formulation including such information as the mass collected as a function of end-effector longitudinal speed for the brush-wheel and sticky-pad samplers, and the mass collected as a function of projectile speed for the pellet gun sampler. These data represent the realistic behavior of the end effector while in contact with a surface, and represent a low-order model of more complex contact conditions that otherwise would have to be simulated. Numerical results demonstrate the adequacy of these multibody models for spacecraft and manipulator- arm control design. The work contributes to the development of a touch-and-go testbed for small body exploration, denoted as the GREX Testbed (GN&C for Rendezvous-based EXploration). The GREX testbed addresses the key issues involved in landing on an asteroidal body or comet; namely, a complex, low-gravity field; partially known terrain properties; possible comet outgassing; dust ejection; and navigating to a safe and scientifically desirable zone.

Quadrelli, Marco↗
NASA NTRS1977

Proceedings of the Spacecraft Charging Technology Conference

Over 50 papers from the spacecraft charging conference are included on subjects such as: (1) geosynchronous plasma environment, (2) spacecraft modeling, (3) spacecraft materials characterization, (4) spacecraft materials development, and (5) satellite design and test.

Pike, C. P.↗
NASA NTRS1999

Improved Earth Sensor Performance Using a Sequentially Correlated Noise Model

Spacecraft attitude estimation by means of an extended Kalman filter requires a reasonably true model of the inherent noise of each sensor. For some sensors, the largest uncorrected noise comes not from the sensor itself, but from errors in the model for the predicted observations. This is certainly the case for Earth horizon sensors. The Earth horizon as seen from low Earth orbit is nearly a circle whose radius depends primarily on altitude. A straightforward latitude-dependent correction is added to this to account for the oblateness of the Earth. There also are both seasonal and stochastic variations in the horizon height. The seasonal variations can be predicted to some limited degree based on models de(ived from historical data. The stochastic component characteristically shows variations that are correlated both in time and space but which are unpredictable over long time spans. This work investigates whether Earth horizon sensor performance can be improved by solving for its systematic error as an augmentation of an attitude Kalman filter. It is found that using only Earth and Sun sensors, the augmented state is not fully observable. Even when magnetometer data is included, only the pitch axis component of the error can be improved; the roll component is unobservable.

Sedlak, Joseph↗
NASA NTRS1999

Improved Earth Sensor Performance Using a Sequentially Correlated Noise Model

Spacecraft attitude estimation by means of an extended Kalman filter requires a reasonably true model of the inherent noise of each sensor. For some sensors, the largest uncorrected noise comes not from the sensor itself, but from errors in the model for the predicted observations. This is certainly the case for Earth horizon sensors. The Earth horizon as seen from low Earth orbit is nearly a circle whose radius depends primarily on altitude. A straightforward latitude-dependent correction is added to this to account for the oblateness of the Earth. There also are both seasonal and stochastic variations in the horizon height. The seasonal variations can be predicted to some limited degree based on models derived from historical data. The stochastic component characteristically shows variations that are correlated both in time and space but which are unpredictable over long time spans. This work investigates whether Earth horizon sensor performance can be improved by solving for its systematic error as an augmentation of an attitude Kalman filter. It is found that using only Earth and Sun sensors, the augmented state is not fully observable. Even when magnetometer data is included, only the pitch axis component of the error can be improved; the roll component is unobservable.

Sedlak, J.↗
NASA NTRS2007

Semianalytical Propagation of Satellite Orbits about an Arbitrary Central Body

Precision mean element (PME) satellite theories play a key role in orbit dynamics analyses. These theories employ: nonsingular orbital elements comprehensive force models Generalized Method of Averaging Numerical interpolation concepts The Draper Semianalytical Satellite Theory (DSST) (Refs. 1 - 6), whose development was led by the author, and the independently-developed Universal Semianalytical Method (USM) (Ref. 7) are examples of such theories. These theories provide the capability to tailor the force modeling to meet the desired computational speed vs. accuracy trade-off. The flexibility of such theories is demonstrated by their ability to include complicated atmosphere density models and spacecraft models in the perturbation theory context. The value of high speed satellite theories, in this era of computational plenty, is that they allow new ways of looking at astrodynamical problems such as orbit design (Refs. 8, 9) and atmosphere density updating (Refs. 10, 11). In the mid to late-1980 s, the geodynamics community led the development of very precise geopotential models such as GEM T2 and GEM T3 (Ref. 12), and with the subsequent analysis of the TOPEX flight data, JGM-2 and JGM-3 (Ref. 13). These were high degree and order geopotentials, at least 50 x 50. In 1993, the DSST implementation in the GTDS program was extended to include the 50 x 50 geopotential models (Ref. 14). The 50 x 50 geopotential, J2000 integration coordinate system, and solid Earth tide capabilities were integrated in GTDS by Scott Carter (Ref. 15). This capability demonstrated 1 m accuracy versus the TOPEX Precise Orbit Ephemerides. Subsequently the DSST Standalone program was also extended to include high degree and order geopotential models (Ref. 5). More recently GTDS has been hosted in the Linux PC environment. However, all of these efforts have been limited to modeling the motion of an artificial Earth satellite. They did not consider the additional complexities associated with lunar, planetary, or other natural satellite orbiters. Such complexities include: additional coordinate systems (associated with the direction of the north pole of rotation and the prime meridian of the new central bodies) (Ref. 16) normalized gravity model coefficients (desirable for high degree and order fields) (Ref. 17) indirect oblateness

Cefola, Paul J.↗
NASA NTRS2002

Development and Implementation of an Empirical Ionosphere Variability Model

Spacecraft designers and operations support personnel involved in space environment analysis for low Earth orbit missions require ionospheric specification and forecast models that provide not only average ionospheric plasma parameters for a given set of geophysical conditions but the statistical variations about the mean as well. This presentation describes the development of a prototype empirical model intended for use with the International Reference Ionosphere (IRI) to provide ionospheric Ne and Te variability. We first describe the database of on-orbit observations from a variety of spacecraft and ground based radars over a wide range of latitudes and altitudes used to obtain estimates of the environment variability. Next, comparison of the observations with the IRI model provide estimates of the deviations from the average model as well as the range of possible values that may correspond to a given IRI output. Options for implementation of the statistical variations in software that can be run with the IRI model are described. Finally, we provide example applications including thrust estimates for tethered satellites and specification of sunrise Ne, Te conditions required to support spacecraft charging issues for satellites with high voltage solar arrays.

Minow, Joesph I.↗
NASA NTRS1971

An approximate theory of imperfect modeling with application to thermal modeling of spacecraft.

Proposal of a new concept of model testing which makes use of imperfect models and is based on the heuristic argument of representing the error states in a multidimensional Euclidean space when the errors in the modeling parameter are sufficiently small. By a separation of these errors into positive and negative groups, and from a consideration of the error paths in the hyperspaces, it is shown that the global effect of these errors may be evaluated with a good degree of approximation. Conditions under which the procedure would yield satisfactory results are discussed. To test the usefulness of the theory a computer experiment was conducted for the prediction of both transient and steady state thermal behavior of a hypothetical spacecraft using perfect, as well as imperfect, models.

Chao, B. T.↗
NASA NTRS1993

Model of spacecraft atomic oxygen and solar exposure microenvironments

Computer models of environmental conditions in Earth orbit are needed for the following reasons: (1) derivation of material performance parameters from orbital test data, (2) evaluation of spacecraft hardware designs, (3) prediction of material service life, and (4) scheduling spacecraft maintenance. To meet these needs, Boeing has developed programs for modeling atomic oxygen (AO) and solar radiation exposures. The model allows determination of AO and solar ultraviolet (UV) radiation exposures for spacecraft surfaces (1) in arbitrary orientations with respect to the direction of spacecraft motion, (2) overall ranges of solar conditions, and (3) for any mission duration. The models have been successfully applied to prediction of experiment environments on the Long Duration Exposure Facility (LDEF) and for analysis of selected hardware designs for deployment on other spacecraft. The work on these models has been reported at previous LDEF conferences. Since publication of these reports, a revision has been made to the AO calculation for LDEF, and further work has been done on the microenvironments model for solar exposure.

Bourassa, R. J.↗
NASA NTRS1977

Plasma distribution and spacecraft charging modeling near Jupiter

To assess the role of spacecraft charging near Jupiter, the plasma distribution in Jupiter's magnetosphere was modeled using data from the plasma analyzer experiments on Pioneer 10 (published results) and on Pioneer 11 (preliminary results). In the model, electron temperatures are kT = 4 eV throughout, whereas proton temperatures range over 100 or equal to kT or equal to 400 eV. The model fluxes and concentrations vary over three orders of magnitude among several corotating regions, including, in order to increasing distance from Jupiter, a plasma void, plasma sphere, sporadic zone, ring current, current sheet, high latitude plasma and magnetosheath. Intermediate and high energy electrons and protons (to 100 MeV) are modeled as well. The models supply the information for calculating particle fluxes to a spacecraft in the Jovian environment. The particle balance equations (including effects of secondary and photoemission) then determine the spacecraft potential.

Goldstein, R.↗
NASA NTRS2014

Advanced Mirror & Modelling Technology Development

The 2020 Decadal technology survey is starting in 2018. Technology on the shelf at that time will help guide selection to future low risk and low cost missions. The Advanced Mirror Technology Development (AMTD) team has identified development priorities based on science goals and engineering requirements for Ultraviolet Optical near‐Infrared (UVOIR) missions in order to contribute to the selection process. One key development identified was lightweight mirror fabrication and testing. A monolithic, stacked, deep core mirror was fused and replicated twice to achieve the desired radius of curvature. It was subsequently successfully polished and tested. A recently awarded second phase to the AMTD project will develop larger mirrors to demonstrate the lateral scaling of the deep core mirror technology. Another key development was rapid modeling for the mirror. One model focused on generating optical and structural model results in minutes instead of months. Many variables could be accounted for regarding the core, face plate and back structure details. A portion of a spacecraft model was also developed. The spacecraft model incorporated direct integration to transform optical path difference to Point Spread Function (PSF) and between PSF to modulation transfer function. The second phase to the project will take the results of the rapid mirror modeler and integrate them into the rapid spacecraft modeler.

Effinger, Michael↗