Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SODIUM OXIDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Neutron scattering measurement of water content and chemical composition of alkali-glass powder reacted gel

Highlights: • Water absorption ability of alkali-glass powder reacted gel was largely reduced comparing other reported alkali-silica gels. • Both SAXS and SANS results showed similar internal structures of samples prepared with different H2O:D2O mixing ratios. • Neutron scattering method was developed to non-destructively determine gel water content and mass density of reacted gels. • Neutron scattering methods (based on scattering length density) on gel water content was validated with TGA measurement. - Abstract: Recent studies demonstrated that the added glass powder with high-alumina content could significantly reduce Alkali-Silica Reaction (ASR) damage in cement concrete. This paper aims to investigate the gel water content, chemical composition and expansion behavior of the alkali-glass powder reacted gel by using neutron scattering and other characterization techniques. Three types of samples were prepared with glass powder, sodium oxide and deuteroxide/hydrogen water with different molar ratios. The swelling potential of this alkali-glass powder reacted gel was much lower than that of the reported alkali-silica reacted gel. The gel water content and chemical compositions were characterized with small-angle neutron scattering (SANS) technique, supported by small-angle X-ray scattering (SAXS), prompt-gamma ray neutron activation analysis (PGAA) measurement. The SAXS test results showed the close scattering intensities, and thus similar internal microstructures among these samples. The elemental molar ratios of gels were obtained from the PGAA test results. Then the gel water molar ratio and mass density were determined by neutron scattering contrast calculation. The determined gel water content from neutron scattering analysis was validated with zero contrast analysis and TGA experimental measurement. Overall, this paper demonstrated the feasibility of using SANS technique to determine the water content of alkali-glass powder reacted gel.

36 MATERIALS SCIENCE↗

Organic and Aqueous Redox Speciation of Cu(III) Periodate Oxidized Transuranium Actinides

A hexavalent group actinide separation process could streamline used nuclear fuel recycle and waste management. The limiting factor to such a process compatible with current fuel dissolution practices is obtaining and maintaining hexavalent Am, in molar nitric acid due to the high reduction potential of the Am(VI)/Am(III) couple (1.68 V vs SCE). Two strong oxidants, sodium bismuthate and Cu(III) periodate, have demonstrated quantitative oxidation of Am under molar acid conditions and better than 50% recovery by diamyl amylphosphonate (DAAP) is possible under these same conditions. This work considers the use of Cu(III) periodate to oxidize Np(V) to Np(VI) and Pu(IV) to Pu(VI) and recover these elements by extraction with DAAP. A metal:oxidant ratio of 1:1.2 and 1:3 was necessary to quantitatively oxidize Np(V) and Pu(IV), respectively, to the hexavalent state. Extraction of hexavalent Np, Pu, and Am by 1 M DAAP in n-dodecane was measured using UV-Vis [Pu(VI), Am (VI)] and NIR [Np(VI)]. Distribution values of Am(VI) were found to match previous tracer level studies. The organic phase spectra of Np, Pu, and Am are presented and molar absorptivities are calculated for characteristic peaks. Hexavalent Pu was found to be stable in the organic phase while Np(VI) showed some reduction to Np(V) and Am was present as Am(III), Am(V), and Am(VI) species in aqueous and organic phases during the extraction experiments. These results demonstrate, for the first time, the ability to recover macroscopic amounts of americium that would be present during fuel reprocessing and are the first characterization of Am organic phase oxidation state speciation relevant to a hexavalent group actinide separation process under acidic conditions.

americium↗

Preparation of: I. intercalative metal oxide/conductive polymer composites as electrode materials for rechargeable batteries; II. sodium rich manganese oxide hydrate with capacity for aqueous Na-ion electrochemical energy storage

The present invention is directed at intercalative metal oxide/conductive polymer composites suitable for use as electrode materials for rechargeable batteries. The composites can be prepared by agitation of the metal oxide and the conductive polymer in aqueous media. The present invention is also directed at a sodium rich layered manganese oxide hydrate prepared by annealing manganese (II, III) oxide and sodium hydroxide. The sodium rich manganese (III, IV) oxide so formed indicates an enhanced capacity for Na-ion storage suitable for the use of electrode materials for aqueous energy storage.

Xiaowei, Teng↗

Effect of a structural disorder on the magnetic properties of the sodium–cobalt tellurate Na{sub 3.70}Co{sub 1.15}TeO{sub 6}

A new layered oxide, sodium–cobalt tellurate Na{sub 3.70}Co{sub 1.15}TeO{sub 6}, is synthesized and structurally characterized, and its static and dynamic magnetic properties are studied. This compound has a new monoclinic structure type with quasi-one-dimensional cation ordering in magnetically active layers. This compound is antiferromagnetically ordered at a Néel temperature T{sub N} ~ 3.3 K, and the temperature and field dependences of magnetization suggest competing antiferromagnetic and ferromagnetic interactions. EPR spectroscopy reveals complex spin dynamics when temperature changes and the presence of two different paramagnetic centers, which is attributed to the existence of two structurally nonequivalent (regular and antisite) positions for magnetic Co{sup 2+} ions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High rate sodium ion battery anodes from block copolymer templated mesoporous nickel–cobalt carbonates and oxides

In this work, micelle-templated ordered mesoporous nickel–cobalt carbonates and oxides are fabricated using a metal nitrate–citric acid strategy, which avoids the hydrolysis and aging requirements associated with sol–gel chemistry. A series of mesoporous Ni x Co (3– x ) (CO 3 ) y and Ni x Co (3– x ) O 4 films with varying Ni–Co compositions and 14 ± 4 nm mesopores are fabricated with the same block copolymer template. AFM and GISAXS analysis indicates that the mesostructure is maintained through the formation of the carbonate and oxide, while GIXD profiles confirm formation of pure spinel phases of semi-crystalline Ni x Co (3– x ) O 4 . The micelle templated mesopores are interconnected and provide transport paths for the electrolyte to minimize the solid-state diffusion requirements associated with battery electrodes. These materials exhibit good performance as sodium ion battery anodes even at high current densities of 4 A g –1 . Amongst the mixed-metal oxides, Ni 2 CoO 4 exhibits the highest specific capacity of 239 mA h g –1 after galvanostatic cycling at a current density of 1 A g –1 for 10 cycles. We attribute the superior performance of Ni 2 CoO 4 at high rates to the high surface area and short ion-diffusion paths of the nanoporous anode architecture, while the higher nickel content in the mixed metal oxide provides enhanced stability during oxide formation along with enhanced electronic conductivity, leading to improved cycling stability of the anode. This micelle template metal nitrate–citric acid method enables new possibilities for fabricating variety of ordered mesoporous mixed-metal carbonates and oxides that could be used in a wide range of applications.

25 ENERGY STORAGE↗

High Selectivity Reactive Carbon Dioxide Capture over Zeolite Dual-Functional Materials

Reactive carbon dioxide capture (RCC) is a process where carbon dioxide (CO 2 ) is captured from a mixed gas stream (such as air) and converted to products without first performing a separation step to concentrate the CO 2 . Here, in this work, zeolite dual-functional materials (ZFMs) are introduced and evaluated for simulated RCC. The studied ZFMs feature high surface area, crystalline, microporous zeolite faujasite (FAU) as the support. Sodium oxide (“Na 2 O”) is impregnated as an effective capture agent capable of scavenging low concentration CO 2 (1,000 ppm). Exchanged and impregnated sodium on FAU chemisorbs CO 2 as carbonates and bicarbonates but does not promote the conversion of sorbed CO 2 to products when heated in hydrogen. The addition of Ru promotes the formation of formates, while the addition of Pt generates carbonyl surface species when heated in hydrogen. The active metal then promotes extremely high selectivity for CO 2 hydrogenation to either methane on Ru catalyst (~150 °C) or carbon monoxide on Pt catalyst (~200 °C) when heated in reducing atmospheres.

36 MATERIALS SCIENCE↗

Copper-containing layered oxide cathodes for sodium-ion batteries

Layered transition metal oxides are among the most promising cathode materials for sodium-ion batteries due to their high theoretical capacity, structural tunability, and cost-effectiveness. However, conventional Ni- and Co-based layered oxides are hindered by high raw material costs, limited elemental abundance, and phase instability during electrochemical cycling. Recently, copper has emerged as an attractive alternative transition metal, offering significant advantages in terms of redox activity, structural stabilization, voltage regulation, and rate performance. Unlike Ni and Co, Cu can facilitate unique redox mechanisms and enable more sustainable material design. This review systematically summarizes recent progress on Cu-containing layered sodium oxides, with emphasis on their structural characteristics, electrochemical behavior, and the critical roles that Cu plays within the host lattice. The insights provided herein aim to highlight the potential of Cu-substituted or Cu-containing layered oxides as a viable pathway toward high-performance and resource-accessible SIB cathodes for future energy storage applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reduction Rates for Higher Americium Oxidation States in Nitric Acid

The stability of hexavalent americium was measured using multiple americium concentrations and nitric acid concentrations after contact with the strong oxidant sodium bismuthate. Contrary to our hypotheses Am(VI) was not reduced faster at higher americium concentrations, and the reduction was only zero-order at short time scales. Attempts to model the reduction kinetics using zero order kinetic models showed Am(VI) reduction in nitric acid is more complex than the autoreduction processes reported by others in perchloric acid. The classical zero-order reduction of Am(VI) was found here only for short times on the order of a few hours. We did show that the rate of Am(V) production was less than the rate of Am(VI) reduction, indicating that some Am(VI) undergoes two electron-reduction to Am(IV). We also monitored the Am(VI) reduction in contact with the organic diluent dodecane. A direct comparison of these results with those in the absence of the organic diluent showed the reduction rates for Am(VI) were not statistically different for both systems. Additional americium oxidations conducted in the presence of Ce(IV)/Ce(III) ions showed that Am(VI) is reduced without the typical growth of Am(V) observed in the systems sans Ce ion. This was an interesting result which suggests a potential new reduction/oxidation pathway for Am in the presence of Ce; however, these results were very preliminary, and will require additional experiments to understand the mechanism by which this occurs. Overall, these studies have shown that hexavalent americium is fundamentally stable enough in nitric acid to run a separations process. However, the complicated nature of the reduction pathways based on the system components is far from being rigorously understood.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Capture of volatile RuO 4 from oxidized simulated used nuclear fuel solutions

Ruthenium is a challenging fission product in used nuclear fuel (UNF) reprocessing due to its complex redox chemistry, variable speciation in nitric acid, partial extractability, and volatility. This work presents a strategy for Ru removal based on the volatilization of RuO 4 using the strong oxidant sodium bismuthate, followed by RuO 2 deposition onto various substrates. Among the materials tested, polymer-based substrates such as polyolefin wax film (Parafilm®), exhibited superior performance, achieving up to near-quantitative Ru removal from solution. After dissolution of the substrate, 99.6% of the Ru was recovered as RuO 2 . The deposition mechanism onto the polyolefin wax film involves both physisorption and chemical reaction through oxidative cleavage of olefinic bonds within the polymer. In contrast, on inorganic substrates such as Al foil, RuO 4 undergoes incomplete surface adsorption and reduction, as confirmed by FTIR and XPS analyses. This approach remains effective under conditions of simulated oxidation of UNF solutions, selectively removing Ru while leaving other fission products in solution. As a result, capture of RuO 4 offers a practical and efficient strategy for ruthenium decontamination and recovery, offering a route for integration into existing UNF reprocessing flowsheets to enhance overall process safety and performance.

Ruthenium↗

Effect of additives on carbon dioxide uptake and compressive strength of dry-cast concrete

The main thrust of the work reported herein is to study the effect of chemical additives to make beneficial use of carbon dioxide in enhancing the compressive strength of dry-cast concrete. The additives used in this investigation were calcium and magnesium oxides and silicates, nickel oxide, sodium hydroxide, sodium bicarbonate and strontium chloride. The experimental results showed that both the carbonation reactions and the compressive strength of dry-cast concrete mixtures were improved when using chemical additives. Experimental investigations for optimisation were also undertaken with selected additives to further increase the carbon dioxide uptake and improve the compressive strength. The best results were obtained when using calcium silicate in combination with calcium oxide. The early-age compressive strength of specimens made from the optimised mixture increased from 9·82 MPa to 13·32 MPa, and the specimens’ carbon dioxide uptake increased from 8·76% to 10·62% of cement weight.

Construction & Building Technology↗

Development of a chemical-free process utilizing ozone oxidative precipitation for the recovery of cobalt and manganese from acid mine drainage

Acid mine drainage (AMD) has been identified as a viable secondary resource of Co, and Mn. However, recovery of these elements while treating AMD is challenging due to the unfavorable pH and Eh conditions for Co-Mn precipitation. This study investigated the effects of various ligands (hydroxide, carbonate, ammonium, sulfate, and phosphate) and oxidizers (sodium persulfate, potassium permanganate, and ozone) on the precipitation of Co-Mn from AMD through experimental and solution chemistry studies. Ozone was found to be the most effective agent for the recovery of these elements. Based on the results, an AMD treatment process was formulated for selective recovery of multiple critical elements, including Al, REEs, Co, and Mn. More than 95 % of Co and Mn were recovered through the proposed process utilizing chemical-less ozone oxidative precipitation. In conclusion, a precipitate containing 0.9 % Co and 54.6 % Mn was obtained from an AMD source containing 0.9 ppm Co and 41.8 ppm Mn.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of a Flow Stabilization Algorithm Enabling Measurement of Low Oxygen Concentrations in Liquid Sodium

To enhance the automated control of the plugging meter (PM) and thereby enhance detection fidelity in ultralow oxygen environments [≤1 parts per million by weight (wppm)], a novel proportional derivative controller has been implemented with conventional PM hardware. This ramp sign stabilized flow (RSSF) controller manipulates the sign (heating or cooling direction) at a fixed rate, enabling precise temperature adjustment around the saturation temperature of the bulk sodium. This adjustment helps maintain flow stability in a partially formed sodium oxide plug, thus greatly reducing the temperature amplitude in the plugging cycle and promoting simple and accurate oxygen determinations in addition to an increased sampling rate. Rather than relying on the subjective nature of indexing the time when the flow rate changes due to the plugging or unplugging onset to the PM temperature, a running average of the correlated oxygen concentration with time over multiple plugging events can provide oxygen readings ranging from an absolute uncertainty of 500 wppb in real time to less than 50 wppb for a 24-h sampling window. Finally, the RSSF controller was tested at 508 ± 7 wppb with measured oxygen of 542 ± 179 wppb, further reducing the variance between the saturation temperature and the plugging temperature.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

The Importance of Slag Structure to Boron Removal from Silicon during the Refining Process: Insights from Raman and Nuclear Magnetic Resonance Spectroscopy Study

Slag structure plays an important role in determining the relative ease of boron removal from silicon. Correlation between slag structure and boron removal thermodynamics was experimentally studied by Raman and nuclear magnetic resonance (NMR) spectroscopy using CaO-SiO{sub 2}-Na{sub 2}O slags with different optical basicities (0.6 to 0.71). Optimization of slag depolymerization leads to efficient removal of boron. The extent of nonbridged oxygen content (NBO/T) and boron removal gradually increased with an increase in optical basicity from 0.6 to 0.66: B{sub 2}O{sub 3} derived from boron oxidation captured nonbridging oxygens of Q{sup 0}(Si), Q{sup 1}(Si), and Q{sup 2}(Si), and was incorporated into the silicate network in the form of Q{sup 3}(Si and B). When optical basicity increased to 0.71, NBO/T rapidly increased and boron removal decreased considerably. Quick depolymerization of Q{sup 3}(Si and B) deteriorated the stability of boron. Various structural forms of boron in the silicate network were successfully detected: the BO{sub 3} trihedrons {sup [3]}B-3Si, {sup [3]}B-2Si-1NBO, and BO{sub 3} (nonring), and the BO{sub 4} tetrahedrons BO{sub 4} (1B, 3Si) and BO{sub 4} (0B, 4Si). BO{sub 4} (1B, 3Si) was the main structure contributing to the increase of boron capacity; BO{sub 3} (nonring), detected under higher optical basicity conditions, may cause deterioration of boron removal by suppressing its oxidation.

36 MATERIALS SCIENCE↗

The Temperature and Structure Dependence of Surface Tension of CaO-SiO{sub 2}-Na{sub 2}O-CaF{sub 2} Mold Fluxes

The surface tension of mold flux is one of the most important properties and varies with the temperature from the top to the bottom of the mold, which influences the adhesion and lubrication between the liquid mold flux and the solidified shell, further influencing the quality of the continuous billet. In the present paper, the effect of temperature on the surface tension of CaO-SiO{sub 2}-Na{sub 2}O-CaF{sub 2} mold-flux melts with different CaO/SiO{sub 2} mass ratios was investigated using the maximum-pull method. Furthermore, the microstructure of mold fluxes was analyzed using FT-IR and Raman spectra to discuss the change mechanism of surface tension. The results indicated that the temperature dependence of surface tension was different with different CaO/SiO{sub 2} mass ratios, and agreed with the modification of melt structure. When the CaO/SiO{sub 2} mass ratio was 0.67 and 0.85, the change of surface tension with temperature was relatively stable, and the influence of temperature on the structure was small. When the CaO/SiO{sub 2} mass ratio was 1.03 and 1.16, with an increase of temperature, the surface tension decreased linearly and the changing amplitude was large; the degree of polymerization of melts and average radii of silicon-oxygen anions also decreased, which intensified the molecular thermal motion and weakened the intermolecular interaction, resulting in a decrease of surface tension of melts.

36 MATERIALS SCIENCE↗