Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SDT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Fracture Control Requirements for Composite and Bonded Structures

Current new requirements document are top level or specific to shuttle payloads. NASA-STD-5007 top level requirement that imposes fracture control on all manned spacecraft hardware. Composites addressed at very top level. NASA_SDT-5003 imposes fracture control on payloads for the space shuttle. Imposes fracture control on composite and bonded structures. Silent on many important issues such as post proof NDE, residual strength, and reuse. Not adequate for or directly applicable to next generation of spacecraft.

Faile, Gwyn C.↗
NASA NTRS2005

To Land on Europa

The Science Definition Team (SDT) for NASA's Jupiter Icy Moons Orbiter (JIMO) Mission recommends including a lander as an integral part of the science payload of the JIMO Mission. The Europa Surface Science Package (ESSP) could comprise up to 25% of science payload resources. We have identified several key scientific and technical issues for such a lander, including 1) the potential effects of propellant contamination of the landng site, 2) the likely macroscopic surface roughness of potential landing sites, and 3) the desire to sample materials from depths of approximately 1 m beneath the surface. Discussion and consensus building on these issues within the science community is a prerequisite for establishing design requirements.

Shirley, James H.↗
NASA NTRS2009

A3 Subscale Rocket Hot Fire Testing

This paper gives a description of the methodology and results of J2-X Subscale Simulator (JSS) hot fire testing supporting the A3 Subscale Diffuser Test (SDT) project at the E3 test facility at Stennis Space Center, MS (SSC). The A3 subscale diffuser is a geometrically accurate scale model of the A3 altitude simulating rocket test facility. This paper focuses on the methods used to operate the facility and obtain the data to support the aerodynamic verification of the A3 rocket diffuser design and experimental data quantifying the heat flux throughout the facility. The JSS was operated at both 80% and 100% power levels and at gimbal angle from 0 to 7 degrees to verify the simulated altitude produced by the rocket-rocket diffuser combination. This was done with various secondary GN purge loads to quantify the pumping performance of the rocket diffuser. Also, special tests were conducted to obtain detailed heat flux measurements in the rocket diffuser at various gimbal angles and in the facility elbow where the flow turns from vertical to horizontal upstream of the 2nd stage steam ejector.

Saunders, G. P.↗
NASA NTRS2011

Optical Design Trade Study for the Wide Field Infrared Survey Telescope [WFIRST]

The Wide Field Infrared Survey Telescope (WFIRST) mission concept was ranked first in new space astrophysics mission by the Astro2010 Decadal Survey incorporating the Joint Dark Energy Mission (JDEM)-Omega payload concept and multiple science white papers. This mission is based on a space telescope at L2 studying exoplanets [via gravitational microlensing], probing dark energy, and surveying the near infrared sky. Since the release of NWNH, the WFIRST project has been working with the WFIRST science definition team (SDT) to refine mission and payload concepts. We present the driving requirements. The current interim reference mission point design, based on the use of a 1.3m unobscured aperture three mirror anastigmat form, with focal imaging and slitless spectroscopy science channels, is consistent with the requirements, requires no technology development, and out performs the JDEM-Omega design.

Content, David A.↗
NASA NTRS2012

Physics of Acoustic Radiation from Jet Engine Inlets

Numerical simulations of acoustic radiation from a jet engine inlet are performed using advanced computational aeroacoustics (CAA) algorithms and high-quality numerical boundary treatments. As a model of modern commercial jet engine inlets, the inlet geometry of the NASA Source Diagnostic Test (SDT) is used. Fan noise consists of tones and broadband sound. This investigation considers the radiation of tones associated with upstream propagating duct modes. The primary objective is to identify the dominant physical processes that determine the directivity of the radiated sound. Two such processes have been identified. They are acoustic diffraction and refraction. Diffraction is the natural tendency for an acoustic wave to follow a curved solid surface as it propagates. Refraction is the turning of the direction of propagation of sound waves by mean flow gradients. Parametric studies on the changes in the directivity of radiated sound due to variations in forward flight Mach number and duct mode frequency, azimuthal mode number, and radial mode number are carried out. It is found there is a significant difference in directivity for the radiation of the same duct mode from an engine inlet when operating in static condition and in forward flight. It will be shown that the large change in directivity is the result of the combined effects of diffraction and refraction.

Tam, Christopher K. W.↗
NASA NTRS2014

Detection of Optically Faint GEO Debris

There have been extensive optical surveys for debris at geosynchronous orbit (GEO) conducted with meter-class telescopes, such as those conducted with MODEST (the Michigan Orbital DEbris Survey Telescope, a 0.6-m telescope located at Cerro Tololo in Chile), and the European Space Agency's 1.0-m space debris telescope (SDT) in the Canary Islands. These surveys have detection limits in the range of 18th or 19th magnitude, which corresponds to sizes larger than 10 cm assuming an albedo of 0.175. All of these surveys reveal a substantial population of objects fainter than R = 15th magnitude that are not in the public U.S. Satellite Catalog. To detect objects fainter than 20th magnitude (and presumably smaller than 10 cm) in the visible requires a larger telescope and excellent imaging conditions. This combination is available in Chile. NASA's Orbital Debris Program Office has begun collecting orbital debris observations with the 6.5-m (21.3-ft diameter) "Walter Baade" Magellan telescope at Las Campanas Observatory. The goal is to detect objects as faint as possible from a ground-based observatory and begin to understand the brightness distribution of GEO debris fainter than R = 20th magnitude.

Seitzer, P.↗
NASA NTRS2013

Wide Field Infra-Red Survey Telescope (WFIRST) 2.4-Meter Mission Study

The most recent study of the Wide Field Infrared Survey Telescope (WFIRST) mission is based on reuse of an existing 2.4m telescope. This study was commissioned by NASA to examine the potential science return and cost effectiveness of WFIRST by using this significantly larger aperture telescope. We review the science program envisioned by the WFIRST 2012-2013 Science Definition Team (SDT), an overview of the mission concept, and the telescope design and status. Comparisons against the previous 1.3m and reduced cost 1.1m WFIRST design concepts are discussed. A significant departure from past point designs is the option for serviceability and the geostationary orbit location which enables servicing and replacement instrument insertion later during mission life. Other papers at this conference provide more in depth discussion of the wide field instrument and the optional exoplanet imaging coronagraph instrument.

exoplanet imaging coronagraph↗
NASA NTRS2018

Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS): Final Report of the ASCENDS Ad Hoc Science Definition Team

Improved remote sensing observations of atmospheric carbon dioxide (CO2) are critically needed to quantify, monitor, and understand the Earth's carbon cycle and its evolution in a changing climate. The processes governing ocean and terrestrial carbon uptake remain poorly understood,especially in dynamic regions with large carbon stocks and strong vulnerability to climate change,for example, the tropical land biosphere, the northern hemisphere high latitudes, and the Southern Ocean. Because the passive spectrometers used by GOSAT (Greenhouse gases Observing SATellite) and OCO-2 (Orbiting Carbon Observatory-2) require sunlit and cloud-free conditions,current observations over these regions remain infrequent and are subject to biases. These short comings limit our ability to understand and predict the processes controlling the carbon cycle on regional to global scales.In contrast, active CO2 remote-sensing techniques allow accurate measurements to be taken day and night, over ocean and land surfaces, in the presence of thin or scattered clouds, and at all times of year. Because of these benefits, the National Research Council recommended the National Aeronautics and Space Administration (NASA) Active Sensing of CO2 Emissions over Nights,Days, and Seasons (ASCENDS) mission in the 2007 report Earth Science and Applications from Space: National Imperatives for the Next Decade and Beyond. The ability of ASCENDS to collect low-bias observations in these key regions is expected to address important gaps in our knowledge of the contemporary carbon cycle.The ASCENDS ad hoc Science Definition Team (SDT), comprised of carbon cycle modeling and active remote sensing instrument teams throughout the United States (US), worked to develop the mission's requirements and advance its readiness from 2008 through 2018. Numerous scientific investigations were carried out to identify the benefit and feasibility of active CO2 remote sensing measurements for improving our understanding of CO2 sources and sinks. This report summarizes their findings and recommendations based on mission modeling studies, analysis of ancillary meteorological data products, development and demonstration of candidate technologies, anddesign studies of the ASCENDS mission concept.

Kawa, S. Randolph↗
NASA NTRS2017

Evolution of Trajectory Design Requirement of NASA's Planned Europa Clipper Mission

Europa is one of the most scientifically intriguing targets in planetary science due to its potential suitability for extant life. As such, NASA has funded the California Institute of Technology Jet Propulsion Laboratory and the Johns Hopkins University Applied Physics Laboratory to jointly develop the planned Europa Clipper mission—a multiple Europa flyby mission architecture aimed to thoroughly investigate the habitability of Europa and provide reconnaissance data to determine a landing site that maximizes the probability of both a safe landing and high scientific value for a potential future Europa lander. The trajectory design—a major enabling component for this Europa Clipper mission concept—was developed to maximize science from a set of eight model payload instruments determined by a NASA-appointed Europa Science Definition Team (SDT) between 2011-2015. On May 26, 2015, NASA officially selected 10 instruments from 6 different U.S. research facilities and universities. With the selection of instruments have come the development of new science measurement requirements, as well as a rich set of requirements stemming from project policies, planetary protection, and the evolved capability and characteristics of the flight system and mission operations system. This paper will focus on the evolution of requirements levied on the trajectory design, discuss strategies and solutions to the multidimensional optimization problem of designing high fidelity end-to-end trajectories that maximize Europa science while mitigating mission risk, complexity and cost, and last, verification of candidate trajectories to meet the requirements on the trajectory design.

Buffington, Brent↗
NASA NTRS2019

Evaluating Biosignatures for Life Detection

The goal here is to develop a conceptual framework for evaluating the ability of different biosignatures to provide evidence for the presence of life in planned missions or observational studies. The focus is on intrinsic characteristics of biosignatures in a given space environment rather than on their detection, which depends on the current state of technology. Suitable evaluation procedures are based on an extensive body of previous work on related problems in which different options are evaluated to make decisions in business, engineering, medical fields and social or political arena. In these cases, three approaches have proven to be particularly useful. Two of them, signal detection theory (SDT) and Bayesian hypothesis testing are based on probabilities. The third approach, multi-attribute utility (MAU) is based on utility theory.

Pohorille, Andrew↗
NASA NTRSDate not supplied

Source Diagnostic Fan II (22-inch) Duct Mode Characteristics as Measured by the Rotating Rake Mode Measurement System while Operated in the NASA Glenn 9x15 Low Speed Wind Tunnel

The second entry of the Source Diagnostic Test (SDT2) was a continuation of the first SDT entry with additional parameters tested. The rotor, stators, and general flow path hardware used in SDT2 were the same as those for SDT1. This included a radial baseline set of stator vanes, which had a vane count such that the rotor-stator interaction at the fan blade passing fundamental was cut-off, as is typical for modern turbofans. Two sets of stator vanes were designed and tested with a count generating a cut-on rotor-stator interaction at the fan blade passing fundamental. One of the sets maintained the no aerodynamic sweep as the radial baseline, the other was designed with leading edge sweep with the intent to generate lower noise. The NASA Glenn Research Center’s Rotating Rake Mode Measurement System was utilized to obtain a complete map of the acoustic duct modes present. The system is a radial rake immersed into the duct that continuously rotates about the duct centerline. For each of the three stator vane configurations, data were acquired at several different fan speeds which included nominal, approach, cutback, and takeoff conditions. Analysis of the mode power level results at the fan fundamentals showed the improved designed set resulted in lower rotor-stator interaction mode acoustic levels. Multiple-pure tones generated by the M5 rotor in the inlet were also measured.

Turbofan, Duct Modes↗
NASA NTRSDate not supplied

Source Diagnostic Fan II (22-inch) Duct Mode Characteristics as Measured by the Rotating Rake Mode Measurement System while Operated in the NASA Glenn 9x15 Low Speed Wind Tunnel

The second entry of the Source Diagnostic Test (SDT2) was a continuation of the first SDT entry with additional parameters tested. The rotor, stators, and general flow path hardware used in SDT2 were the same as those for SDT1. This included a radial baseline set of stator vanes, which had a vane count such that the rotor-stator interaction at the fan blade passing fundamental was cut-off, as is typical for modern turbofans. Two sets of stator vanes were designed and tested with a count generating a cut-on rotor-stator interaction at the fan blade passing fundamental. One of the sets maintained the no aerodynamic sweep as the radial baseline, the other was designed with leading edge sweep with the intent to generate lower noise. The NASA Glenn Research Center’s Rotating Rake Mode Measurement System was utilized to obtain a complete map of the acoustic duct modes present. The system is a radial rake emersed into the duct that continuously rotates about the duct centerline. For each of the three stator vane configurations, data were acquired at several different fan speeds which included nominal, approach, cutback, and takeoff conditions. Analysis of the mode power level results at the fan fundamentals showed the improved designed set resulted in lower rotor-stator interaction mode acoustic levels. Multiple-pure tones generated by the M5 rotor in the inlet were also measured.

Turbofan↗
NASA NTRS2025

A Minority Report Submitted as an Addendum to the Report of the Mars 2020 Organic Contamination Panel

This Minority Report (MR) presents seven findings in addition to or contrary to the main OCP report: 1. Contamination control for the Mars 2020 cache must be strict. Mars’ surface is known to be organics-poor from laboratory studies, Mars meteorite analyses, and from four previous NASA missions. It is imperative that contamination control measures are enacted that enable reliable and robust detection of potential biomarker compounds at the ppb level. 2. Since Mars 2020 is a sample return mission and analyses of samples in the returnable cache are expected to occur after return to Earth, positive controls are not recommended for flight on Mars 2020 unless a compelling case can be made for their use. 3. The findings of previous panels dedicated to organic compound analysis in Martian samples (OCSSG, ND-SAG, SDT) recommend TOC limits between 10-40 ppb. The MR finds that the lower limit of 10 ppb is recommended and that insufficient justification is given by the OCP Panel Report (PR) to raise the TOC limit to 40 ppb. 4. Analytical capability is sufficiently advanced that analytical capability is an irrelevant consideration with respect to differentiating between 10 and 40 ppb TOC. 5. Perceived contamination control challenges are an irrelevant consideration for raising the TOC contamination limit from 10 to 40 ppb since those challenges, and the procedures to ameliorate them, will exist regardless of whether the limit is 10 or 40 ppb. 6. The “dilution cleaning” method has not been adequately proven for utilization on the Mars 2020 mission. Shortcomings have been identified in terms of peer review, method verification, analytical and testing approach, application to space flight hardware, and performance under Martian conditions. The method should be revisited and independently tested using statistically and analytically robust methods, and scrutinized in a rigorous peer review process. 7. The Mars 2020 mission claims considerable heritage from the Mars Science Laboratory (MSL) mission, but MSL contamination control efforts contain significant errors and implementation discrepancies that would imperil the Mars 2020 caching mission were they repeated. A standing contamination control panel should be formed to provide independent oversight for the Mars 2020 mission.

Mars Sample Return↗
NASA NTRSDate not supplied

Fan Noise Predictions of the NASA Source Diagnostic Test using Unsteady Simulations with LAVA Part II - Tonal and Broadband Noise Assessment

The NASA Source Diagnostic Test (SDT) campaign experimental data is used for validation of a sliding mesh technique recently implemented within the Launch, Ascent, and Vehicle Aerodynamics computational framework for time-accurate simulation of rotating fans. The far-field acoustics are analyzed in this work, building upon the aerodynamic validation studies previously published in Part I. Two modeling approaches are explored: the unsteady Reynolds-averaged Navier Stokes (uRANS) with the negative Spalart-Allmaras (SA-neg) turbulence model closure, and a hybrid Reynolds-averaged Navier Stokes/large-eddy simulation (RANS/LES) paradigm employing a zonal detached-eddy simulation (ZDES) closure with enhanced shielding protection. Two convective flux scheme approaches with different dissipation properties are also explored with ZDES. The Ffowcs-Williams and Hawkings (FW-H) permeable surface approach is used for propagation of the near-field acoustics to the far-field microphone locations. This work analyzes the low-speed (approach) condition, characterized by a fan rotation speed of 7808 rotations-per-minute (RPM). Three different grid levels ranging between 200 million and 1.1 billion grid points are considered. Results show good prediction of the broadband noise levels at sideline angles ranging between 70° and 110°. The forward arc observers show an under-prediction of the overall sound pressure levels (OASPL) even at the fine grid level. A breakdown of the inlet and exhaust contributions reveals a steep drop-off in the broadband noise levels past a blade-passing frequency (BPF) of 1.5, potentially caused by a lack of resolved small-scale turbulent fluctuations in the interstage region. Past 110° the OASPL are over-predicted by up to 10 dB due to an over-prediction of the low-frequency broadband noise levels in the aft arc. The detuning of BPF2 caused by small deviations in the blade stagger angle around the wheel is captured, and a corresponding decrease in the sound power level for this cut-on tone is observed.

AATT↗
DOE OSTI2023

A Reproducible Validation of Algorithms for Estimating Array Tilt and Azimuth from Photovoltaic Power Time Series

In this research, we assess the viability of four different, publicly available algorithms for estimating the azimuth and tilt parameters of solar photovoltaic systems using only the associated AC power time series data and site latitude-longitude coordinates. In this work, we curated a benchmarking data set of 44 fixed-tilt systems, comprising 275 measured AC power inverter data streams, with known azimuth and tilt parameters. Additionally, we isolated test cases in the data set with real-world issues, including shading and clipping, to determine how algorithm performance varies based on the presence of these phenomena. Using this data set for benchmarking, we evaluated the estimated vs. actual system characteristics for each algorithm, as well as the associated algorithm execution time using a standardized benchmarking process. The two highest performing algorithms were the Solar Data Tools and the PVWatts 5-based methods, which both achieved a median absolute error of approximately 5 and 1 degrees for azimuth and tilt, respectively. During run time analysis, the SDT method was approximately 5 times faster than the PVWatts 5-based method, with the median execution time for a stream varying between 6 and 8 seconds vs. a median run time of 31 seconds for the PVWatts 5-based method.

algorithm validation↗
DOE OSTI2025

An isotopic labeling investigation into the influence of the nitro group on LLM-105 thermal decomposition

Here, this work presents the first application of isotopically labeled LLM-105 (2,6-diamino-3,5-dinitropyrazine-1-oxide) to investigate thermal decomposition pathways. Specially synthesized LLM-105 isotopologues were utilized to isolate the influence of labeled 15 NO 2 nitro groups on the formation of lightgas products. Simultaneous differential scanning calorimetry, thermo-gravimetric, and mass spectrometry measurements were employed to track the evolution of product gases, enabling the direct comparison of isotopically shifted species with unlabeled LLM-105. Key findings show that C 2 N 2 production is mainly dependent on nitrogen sources from either the amine groups or the pyrazine ring (i.e., not the nitro groups). The formation of NO, N 2 , and N 2 O all involves the nitro groups to some extent. NO (nitric oxide) was found to be the predominant gas species directly formed from the nitro group of LLM-105. In contrast, mixed nitrogen isotopologues of N 2 and N 2 O (i.e., 14 N 15 N and 15 NNO) formed more readily in comparison to their pure counterparts (i.e., 15 N 2 and 15 N 2 O). This indicates the amine and/or pyrazine groups of LLM-105, in addition to the nitro group, are involved in the decomposition pathways forming N 2 and N 2 O. In addition, our investigation led to the discovery of two previously unreported decomposition products (CHO and HNCO), which were confirmed through hydrogen labelling utilizing deuterium isotopes. These results provide detailed speciation trends of gaseous products during LLM-105 decomposition, offering new insights into reaction pathways. Experimental data reported here will support the development of a detailed chemical kinetics model for LLM-105, essential for the safe handling of high explosives.

Chemistry - Chemical explosives↗
DOE OSTI2021

Development of a Pulsed Slowing-Down-Time Benchmark of Neutron Thermalization in Graphite

Graphite is a classic neutronic material that has been used as both a reactor reflector and moderator in various nuclear reactor systems. The ability to accurately predict the slowing down and thermalization of neutrons in graphite can have significant implications on the safety and operation of such reactor systems. In reactors, the neutron thermalization process is quantified using the thermal scattering law (TSL) and related cross sections for a given moderator. An ideal approach to assess the validity of TSL data is using benchmark measurement based on the pulsed Slowing-Down-Time technique and its comparison with the appropriate graphite nuclear library. In this work, experimental measurement and computational Monte Carlo simulations were performed to benchmark the slowing down characteristics and thermalization of neutrons in nuclear (reactor-grade) graphite. Given the density of graphite, various graphite libraries were selected for the benchmark analysis.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗