Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SCALE EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Real gas scale effects on hypersonic laminar boundary-layer parameters including effects of entropy-layer swallowing

Inviscid and viscous (laminar boundary-layer) flow-field calculations under perfect gas hypersonic wind tunnel and equilibrium real gas flight conditions are presented for the windward centerline of the Rockwell International 139 Space Shuttle Orbiter at a 30-deg angle of attack. Correlation parameters for laminar boundary-layer edge quantities and surface heat transfer are developed which properly account for entropy-layer-swallowing effects under both real and perfect gas conditions. Some implications of the proposed correlation parameters on boundary-layer transition are discussed.

Adams, J. C., Jr.↗
NASA NTRS1980

Scale effects in the dynamic transfer functions for cavitating inducers

Dynamic transfer functions for two cavitating inducers of the same geometry but different size are presented, compared and discussed. The transfer functions for each inducer indicate similar trends as the cavitation number is decreased; only minor changes are noted with changes in the flow coefficient, the uniformity of the inlet flow or the temperature of the water (21-74 C). The non-dimensional results for the two sizes are compared with themselves and with theoretical calculations based on the bubbly flow model. All three sets of results compare well and lend further credence to the theoretical model. The best values of the two parameters in the model are evaluated and recommended for use in applications.

Brennen, C. E.↗
NASA NTRS1987

Pressure scaling effects in a scramjet combustion chamber

The test results obtained for a model scramjet over a range of pressure levels corresponding to different flight altitudes involve enthalpies that vary from the ignition limit, at the low temperature end, to temperatures where the dissociation of combustion products severely limits heat release. The minimum temperature is noted to be highly pressure-sensitive; above the ignition limit, the amount of heat release increased markedly with pressure and with combustion chamber length. A FEM computer code has been used to model the mixing and combustion processes.

Morgan, R. G.↗
NASA NTRS1991

Scale effects in buckling, postbuckling and crippling of graphite-epoxy Z-section stiffeners

The buckling, postbuckling and crippling of Hercules Inc. AS4/3502 graphite-epoxy Z-section stiffeners is investigated as a function of specimen structural parameters. Variables addressed are flange and web widths, flange-to-web corner radius, thickness and stacking sequence. Analytical, numerical and experimental results are discussed. Nondimensional parameters have been obtained from an analytical model which effectively normalize the initial local buckling data reported herein and in the references. The nature of the load redistribution after buckling and its impact on postbuckling stiffness is related to the geometric variables. A normalized total width concept is used to unify the crippling data.

Wieland, Todd M.↗
NASA NTRS1992

Scaling effects in angle-ply laminates

The effect of specimen size upon the response and strength of +/- 45 degree angle-ply laminates was investigated for two graphite fiber reinforced plastic systems and several stacking sequences. The first material system was a brittle epoxy based system, AS4 fibers in 3502 epoxy, and the second was a tough thermoplastic based system, AS4 fibers in PEEK matrix. For the epoxy based system, two generic +/- 45 degree lay-ups were studied: (+45 degrees sub n/-45 degrees sub n) sub 2S (blocked plies), and (+45 degrees/-45 degrees) sub 2nS, for n=1 and 2. The in-plane dimensions of the specimens were varied such that the width/length relationship was 12.7 x n/127 x n mm, for m=1, 2, 3, or 4. It is shown that the stress/strain response and the ultimate strength of these angle-ply laminates depends on the laminate thickness and the type of generic lay-up used. Furthermore, it is shown that first ply failure occurs in the surface plies as a result of normal rather than shear stresses. The implications of the experimental findings upon the validity of the +/- 45 degree tensile test which is used to determine the in-plane shear response of unidirectional composites are discussed.

Kellas, Sotiris↗
NASA NTRS1992

Numerical simulation of geometric scale effects in cylindrical self-field MPD thrusters

A 2D, two-temperature, single fluid MHD code which incorporates classical plasma transport coefficients and Hall effects has been developed to predict steady-state, self-field MPD thruster performance. The governing equations and numerical methods of solution are outlined and discussed. Experimental comparisons are used to validate model predictions. The model accurately predicts thrust and reproduces trends in the discharge voltage for discharge currents below experimentally measured onset values. However, because the model does not include electrode effects the calculated voltage drops are significantly lower than experimentally measured values. Predictions of thrust and flow efficiency are made for a matrix of fifteen cylindrical thruster geometries assuming a fully ionized argon propellant.

Lapointe, M.↗
NASA NTRS1933

Scale Effect of Model in Seaplane-float Investigations

For the purpose of solving all the problems involved, an investigation was made with flat, rectangular planing surfaces. The investigation of a flat, rectangular planing surface, which can be considered as the portion of a flat float bottom lying in front of the step, has the advantage that the frictional resistance can be determined directly from the test results. Normal and tangential forces act on the lower side of the planing surface towed through still water, while the upper side and the lateral edges are under constant atmospheric pressure.

Sottorf, W↗