Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Rock sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Rare Earth Elements (REEs) Measurement in Coal and Rock Mineral Matrices

Although critical minerals including rare earth elements (REEs) can be analyzed in laboratory by some established and reliable laboratory based analytical techniques, their in-situ measurements in the field have always been challenging. For identification of REE-rich sites and REEs distribution measurement, portable field applicable technologies are paramount. As Laser-induced breakdown spectroscopy (LIBS) has enormous potential for field measurement, it has been explored for REEs measurements by many research groups. However, most of the studies are still dealing with simulated samples with traditional bench top experiments. In real world, REEs are available in various types of natural complex matrices in low content depending on the geographical locations. Considering this, LIBS has been evaluated for REE measurement in two different complex coal and rock mineral matrices representing some natural REE-rich sites. In addition, multiple samples collected from some natural sites in Wyoming, USA were experimented by using NETL’s bench top as well as miniaturized prototype setups for REE measurements.

Bhatt, Chet R.↗
DOE OSTI2025

Reaction-Induced Fracturing of Porous Carbonate Rocks during Volume-Increasing Replacement by Witherite

Volume-increasing replacement reactions can lead either to fracturing of the parent phase or to the formation of cohesive layers that passivate further reaction, but the factors that drive one outcome or the other are not understood. In this experimental study, we investigated the volume-increasing replacement of carbonate rocks (consisting of CaCO 3 and CaMg(CO 3 ) 2 ) of different porosity by witherite (BaCO 3 ). Samples were characterized using scanning electron microscopy, Raman spectroscopy, small-angle neutron/X-ray scattering, X-ray tomography, and scanning transmission electron microscopy. We observed the formation of a witherite reaction layer and witherite formation within pores and along grain boundaries. Despite this being a volume-increasing replacement reaction, newly formed witherite was porous, potentially allowing further replacement. Filled fractures were observed in the low-porosity carbonates, whereas witherite formed within pores in high-porosity carbonates. We conclude that fracturing of the parent phase versus passivation is contingent on the initial microstructure of the parent with an optimal degree of porosity required for fracturing.

Calcite↗
DOE OSTI2024

Permeability and Induced Polarization of Mudstones

Electrical measurements can be used to estimate hydraulic properties such as permeability ( k ) in sedimentary rocks. Previous work has focused on sandstones, siltstones, and carbonates, while investigations on mudstones have rarely been reported. In this study, we report on electrical geophysical measurements for 23 mudstone samples using an experimental approach designed to reliably saturate these low permeability mudstones. The modified Hagen-Poiseuille model linking permeability to the formation factor ( F ) and an effective pore radius ( r ) provides an excellent fit to the data set with a near-constant pore radius, indicating that the effective porosity (1/ F ) is the controlling factor on k . In these samples, the surface area normalized to pore volume ( S por ), frequently used in permeability estimation models, varies by 1–2 orders of magnitude and is thus not a reliable proxy of the inverse effective hydraulic radius. The formation factor also exerts the primary control on induced polarization (IP) parameters, whereas Spor shows no relation to the IP parameters. A strong linear relationship is found between IP parameters (imaginary conductivity and normalized chargeability) and surface conductivity, although the proportionality factor is significantly lower than those observed in more permeable rocks and sediments. Apparent relationships between the polarization strength-derived and time constant-derived geophysical length scales and the effective hydraulic radius appear to be driven by variations in the electrochemical parameters (i.e., specific polarizability and diffusion coefficient). Overall, these findings emphasize that predicting hydraulic properties from electrical measurements in fine-grained rocks remains challenging and requires further investigation into the electrochemical properties involved.

58 GEOSCIENCES↗
DOE OSTI2025

Permeability scaling relationships of volcanic tuff from core to field scale measurements

A recent chemical explosive test in P-Tunnel at the Nevada National Security Site, Nevada, USA, was conducted to better understand how signals propagate from explosions in the subsurface. A primary signal of interest is the migration of gases that can be used to differentiate chemical from nuclear explosions. Gas migration is highly dependent on the rock permeability which is notoriously difficult to determine experimentally in the field due to a potentially large dependence on the scale over which measurements are made. Here, we present pre-explosion permeability estimates to characterize the geologic units surrounding the recent test. Permeability measurements were made at three scales of increasing size: core samples (≈2 cm), borehole packer system tests (≈1 m), and a pre-shot cavity pressurization test (> 10 m) across ten tuff units. Permeability estimates based on core measurements showed little difference from borehole packer tests. However, permeability in most rock units calibrated from cavity pressurization tests resulted in higher permeability estimates by up to two orders of magnitude. Here, we demonstrate that the scale of the measurement significantly impacts the characterization efforts of hydraulic properties in volcanic tuff, and that local-scale measurements (< 10 m scale) do not incorporate enough heterogeneity to accurately predict field-scale flow and mass transport.

Environmental sciences↗
DOE OSTI2024

Site Characterization of the Highest-Priority Geologic Formations for CO2 Storage in Wyoming

The project Site Characterization of the Highest-Priority Geologic Formations for CO2 Storage in Wyoming is one of 9 site characterization projects that were implemented as part of ARRA (American Recovery and Reinvestment Act). Data from this project was used to improve resolution of data in NATCARB in the area of study. Data related to this study has already been incorporated in NATCARB Atlas. The Wyoming Carbon Underground Storage Project (WY-CUSP) consisted of CO2 storage site characterization and evaluation, focusing on Wyoming’s most promising CO2 storage reservoirs (the Pennsylvanian Weber/Tensleep Sandstone and Mississippian Madison Limestone) and premier CO2 storage site (Rock Springs Uplift). Results from the WY-CUSP project suggest the two reservoirs could store up to 17,000 million tons of CO2. The WY-CUSP team drilled a stratigraphic test well and acquired a 3-D seismic survey covering 25 square miles of the Rock Springs Uplift site. The team retrieved 916 feet of core from the 12,810-foot-deep well, along with a complete log suite, borehole images, fluid samples, and other data. Project partners (1) provided continuous visual documentation of the core, including grain size, mineralogy, facies distribution, and porosity; (2) performed continuous permeability and velocity scans of selected reservoir intervals; and (3) chemically analyzed the fluid samples. WY-CUSP scientists integrated seismic attributes with observations from log suites, a VSP survey, core, fluid samples, and laboratory analyses, including continuous permeability scans. From these integrations, researchers constructed 3-D spatial distribution volumes of reservoir and seal properties that represent geological heterogeneity at the targeted CO2 storage site. The WY-CUSP team used this data to perform new CO2 plume migration simulations. Baker Hughes, Inc., completed a series of small-scale, in-situ water injectivity measurements. A database was formed when observations, analyses, and experiments from the stratigraphic test well were integrated. Correlation of these data allowed petrophysical parameters to be extrapolated from the test well out into the storage domain (5x5 mile 3-D seismic survey volume). This resulted in an improved, realistic understanding of performance assessments for potential CO2 storage scenarios. The WY-CUSP team worked on (1) improving CO2 storage resource estimates, (2) establishing long-term integrity and permanence of confining layers, (3) designing a profitable strategy for pressure management, and (4) evaluating the utilization of stored CO2 at the Rock Spring Uplift. Finally, Baker Hughes developed a microseismic baseline for the test site using in-bore geophones to complete field operations.

3-D seismic↗
DOE OSTI2025

Using Radiogenic Noble Gas Nuclides to Identify and Characterize Rock Fracturing

Abstract Fracture‐released radiogenic noble gas nuclides are used to identify locations and constrain the volume of new fracture creation during subsurface detonations. Real‐time, in situ noble gases and reactive gases were monitored using a field‐deployed mass spectrometer and automated sampling system in a multilevel borehole array. Released gases were measured after two different detonations having distinct energy, pressure, and gas volume characteristics. Explosive‐derived gases (N 2 O, CO 2 ) and excess radiogenic 4 He and 40 Ar above atmospheric background are used to identify locations of gas transport and new fracture creation after each detonation. Fracture‐released radiogenic 4 He is used to constrain the volume of newly created fractures with a model of helium release from fracturing. Explosive by‐product gas was observed in multiple locations both near and distal to the shot locations for both detonations. Radiogenic 4 He and 40 Ar release from rock damage was observed in locations near the detonation after the second, more powerful detonation. Observed 4 He response is consistent with a model of diffusive release from newly created fractures. Volume of new fractures estimated from the 4 He release ranges from 1 to 5 m 2 with apertures ranging from 0.1 to 1 m. Our results provide evidence that radiogenic noble gases released during fracture creation can be identified at the field scale in real time and used to identify timing and location of fracture creation during deformation events. This technique could be useful in subsurface science and engineering problems where the location and amount of newly created rock fracturing is of interest including fault rupture, mine safety, subsurface detonation monitoring and reservoir stimulation.

58 GEOSCIENCES↗
DOE OSTI2024

Eliminating chemo-mechanical degradation of lithium solid-state battery cathodes during >4.5 V cycling using amorphous Nb2O5 coatings

Abstract Lithium solid-state batteries offer improved safety and energy density. However, the limited stability of solid electrolytes (SEs), as well as irreversible structural and chemical changes in the cathode active material, can result in inferior electrochemical performance, particularly during high-voltage cycling (>4.3 V vs Li/Li + ). Therefore, new materials and strategies are needed to stabilize the cathode/SE interface and preserve the cathode material structure during high-voltage cycling. Here, we introduce a thin (~5 nm) conformal coating of amorphous Nb 2 O 5 on single-crystal LiNi 0.5 Mn 0.3 Co 0.2 O 2 cathode particles using rotary-bed atomic layer deposition (ALD). Full cells with Li 4 Ti 5 O 12 anodes and Nb 2 O 5 -coated cathodes demonstrate a higher initial Coulombic efficiency of 91.6% ± 0.5% compared to 82.2% ± 0.3% for the uncoated samples, along with improved rate capability (10x higher accessible capacity at 2C rate) and remarkable capacity retention during extended cycling (99.4% after 500 cycles at 4.7 V vs Li/Li + ). These improvements are associated with reduced cell polarization and interfacial impedance for the coated samples. Post-cycling electron microscopy analysis reveals that the Nb 2 O 5 coating remains intact and prevents the formation of spinel and rock-salt phases, which eliminates intra-particle cracking of the single-crystal cathode material. These findings demonstrate a potential pathway towards stable and high-performance solid-state batteries during high-voltage operation.

Science & Technology - Other Topics↗
DOE OSTI2026

Stress and Strain Heterogeneity and Persistence in Uniaxially‐ and Triaxially‐Loaded Sandstone

Two critical questions in brittle rock mechanics are how rocks developed localized strains and to what extent internal stress heterogeneity controls this localization and subsequent macroscopic failure. Definitive answers have not yet been found, but would provide insight into rock fracture mechanics as relevant to hydrocarbon extraction and sequestration. Here, we use synchrotron X‐ray tomography (XRT) and 3D X‐ray diffraction (3DXRD) during uniaxial and triaxial tests on Nugget and Bentheimer sandstones to examine strain and stress localization prior to mechanical failure. 3DXRD was used to measure intra‐granular lattice strains which were used to compute elastic stress tensors of each grain. Digital volume correlation (DVC) was applied to XRT images to determine the strain field in the sample. Both samples featured marked spatial heterogeneity, localization, and temporal persistence of elevated stresses and strains during their mechanical deformation toward failure. Both samples featured a majority of grains with at least one principal stress component that was tensile, a signature of the influence of heterogeneity on stress transmission. Measurements further revealed that compressive stress orientations and statistics evolved in a similar manner to those of inter‐particle forces in loose granular materials, with triaxially‐compressed rock exhibiting enhanced grain stress heterogeneity compared to uniaxially‐compressed rock. Our results complement recent work by others who employed XRT and scanning 3DXRD to study triaxially‐compressed sandstone, but extend those results to uniaxial compression, sandstones of varied porosity, and grain stress measurements throughout the 3D full extent of the samples rather than in a single layer examined with scanning 3DXRD.

58 GEOSCIENCES↗
DOE OSTI2026

Critical Review of Brazil Disk Techniques for Tensile Strength Characterization With an Emphasis on High Explosive Materials

Mechanical properties are a critical performance metric for many high explosive (HE) materials and tensile strength properties are particularly important. Direct tensile measurements using dogbone shaped samples are the gold standard but they have the disadvantage that they are fairly large and require samples machined from billets. Diametral compression, more commonly known as Brazil disk (BD) testing, is an indirect method for measuring tensile strength on smaller and more easily fabricated samples. A review of the BD literature is presented with an emphasis on tensile strength measurements in high explosive materials. BD literature is reviewed in three primary areas: (i) rocks and concrete, (ii) pharmaceutical materials, and (iii) high explosive materials. The literature for rocks/concrete is extensive and dates back over 80 years; despite this there is no consensus on the validity/accuracy of the BD technique or the optimal variant of the BD technique to employ. The pharmaceutical literature is the opposite, being limited in scope and quantity of studies. BD literature on high explosive materials falls in between, not as impressive as in the rocks/concrete community but more substantiative than in the pharmaceutical community. After the review of the literature practical parameters for HE BD testing and recommended future work is discussed.

Brazil disk↗
DOE OSTI2024

Modeling gas migration through clay-based buffer material using coupled multiphase fluid flow and geomechanics with stress-dependent gas permeability

A model for gas migration through clay-based buffer material is developed for modeling gas generation and migration associated with deep geologic nuclear waste disposal. The model is based on a multiphase fluid flow and geomechanics simulator that is adapted to consider enhanced gas flow when gas pressure is high enough to approach the confining stress magnitude. A key feature in the model is a direct coupling between gas permeability and stress, through a non-linear stress-dependent permeability function. The model was first tested and calibrated by modelling two different laboratory gas migration tests on Wyoming (MX-80) bentonite samples. The calibrated model was then applied to model gas migration through a bentonite buffer of a large-scale gas injection test (Lasgit) conducted at the Äspö Hard Rock Laboratory in Sweden. Observed preferential gas migration along interfaces (between compacted blocks and along the canister surface) required explicit representation of such interfaces in the model. The model with the stress-dependent gas permeability accurately captured observed experimental responses in terms of gas breakthrough time, peak gas pressure, and cumulative gas flow rates. The calibrated model was finally applied to simulate migration of hydrogen gas generated within a breached nuclear waste canister over 10,000 years, involving migration of much larger gas volumes. For the considered gas generation rate and host rock properties, the generated gas could migrate through the bentonite buffer and released into the surrounding host rock at a maximum gas pressure somewhat higher than the initial total stress, though a significant amount of hydrogen remained within the buffer. This modelling sets the stage for further detailed analysis of the impact of hydrogen gas generation on the long-term performance of nuclear waste repositories.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Development of an ERT‐Based Framework for Bentonite Buffers Monitoring From Laboratory Tests: 1. Characterizing Thermal–Hydrological–Mechanical Processes

Abstract Bentonite clay is widely used in engineered barrier systems for the permanent disposal of high‐level radioactive waste due to its low permeability, high swelling capacity, and thermal stability. However, the complex thermal‐hydrological‐mechanical (THM) processes induced by heating from decaying radioactive waste and hydration from surrounding rock can lead to heterogeneous changes that are difficult to measure and predict. This study develops an Electrical Resistivity Tomography (ERT)‐based framework for monitoring THM processes, progressing from sample‐scale to bench‐scale tests, to inform field‐scale applications. Sample‐scale tests analyzed small bentonite samples under controlled variations in water content, temperature, and porosity to establish fundamental resistivity relationships. Bench‐scale tests involved larger bentonite columns subjected to heating (up to 200°C) and hydration under controlled pressure, simulating repository conditions. ERT measurements, complemented by X‐ray CT imaging, temperature monitoring, and tracing sensors, revealed coupled THM processes, such as hydration‐induced compression, swelling, and thermal gradients, leading to complex resistivity patterns. The results demonstrate the potential of ERT for capturing THM‐induced resistivity changes, though challenges remain in upscaling and quantitative analysis. This study evaluates laboratory test capabilities and proposes future improvements for understanding THM‐induced resistivity responses. A conceptual framework for ERT implementation in field‐scale monitoring is presented, synthesizing findings from both scales and exploring how ERT data can inform long‐term modeling and reduce prediction uncertainties. Overall, this ERT‐based framework offers a robust method for monitoring bentonite buffers, aiding in early issue detection and supporting the safe long‐term disposal of radioactive waste in geological repositories, while highlighting the need for future development. Plain Language Summary Bentonite clay is crucial in engineered barrier systems (EBS) for containing high‐level radioactive waste due to its ability to absorb water, swell, seal and remain stable under high temperatures. When bentonite absorbs water and heats up from radioactive decay, it experiences complex changes in its physical and mechanical properties. Understanding these changes is important for ensuring the long‐term safety and effectiveness of EBS. This study used Electrical Resistivity Tomography (ERT), a non‐invasive method that measures electrical conductivity to monitor these changes during laboratory experiments. The ERT data revealed significant variations in resistivity corresponding to changes in water content, temperature, and density, providing detailed spatial and temporal insights into the behavior of bentonite. These findings enhance our ability to predict the long‐term performance of bentonite barriers, ensuring the safe containment of radioactive waste. By improving our understanding of bentonite's behavior, this research supports the development of more reliable and effective barrier systems for radioactive waste disposal, protecting the environment and public health. Key Points ERT monitoring was employed to capture resistivity changes in bentonite during controlled heating and hydration experiments, providing insights into THM processes ERT data reveal significant resistivity changes correlated with water content, temperature, and mechanical effects, enhancing the understanding of THM dynamics in bentonite This study explores the potential of the framework for application in field‐scale EBS monitoring, emphasizing the need for integrating additional geophysical methods for comprehensive subsurface imaging

Chen, Hang↗
DOE OSTI2026

Geomechanical properties of the Meletta sandstone - the high-temperature heat storage reservoir rock of DeepStor

The DeepStor project aims at storing excess heat at temperatures up to 140 °C in the depleted Leopoldshafen oil field at a depth of about 1300 m. In order to gain knowledge on the target horizons, the different layers of the Meletta sandstone, samples cored in a block retrieved in a quarry near Nussloch where the Meletta sandstone outcrops were studied. Several petrophysical properties were investigated including mineralogy, porosity, permeability, thermal conductivity, P- and S-wave velocities and quality factor. A mechanical study focused on compressive strength under uniaxial and triaxial stress conditions, tensile strength, critical pressure and stress-dependence of physical properties. Our results show that the Meletta sandstone is heterogeneous, anisotropic, mechanically weak, stress-sensitive and prone to water weakening. Petrophysical measurements on few Meletta sandstone cores retrieved in boreholes at about 1250 m depth showed that the outcrop samples are significantly less cohesive and weaker. Therefore, one should consider the Nussloch outcrop as a good reservoir analog only with great caution. Several models were applied to account for our experimental results on anisotropy, mechanical behavior and stress-dependence of the outcrop samples. Our study provides a valuable data set which can feed numerical models to simulate the behavior of the host formation during heat exchange operations in the DeepStor project.

Geomechanics↗
DOE OSTI2025

High-resolution analysis of clay minerals and amorphous materials in martian analog environments

Mudrocks and mud-sized sediments (i.e., silt to clay) dominate the surface of Earth and Mars. These fine-grained sediments preserve a rich history of sedimentary processes from source to sink and shed light on ancient climates. However, both the physical and chemical nature of these materials make them difficult to fully characterize with traditional laboratory techniques. Here, we explore a cross-disciplinary and high-resolution approach using synchrotron radiation for X-ray diffraction, pair distribution function analysis, and submicrometer-scale X-ray fluorescence, combined with transmission electron microscopy, to better understand the nanostructure and composition of mud-sized sediments from a glacio-fluvial watershed in southwest Iceland. Our results demonstrate that sediments in the cold and wet climate of Iceland are more altered than previously thought, as evidenced by the identification of kaolinite and mixed-layer kaolinite-smectite. Additionally, sediments are enriched in amorphous materials and nanocrystalline phases, as determined from grain morphologies and compositions consistent with allophane, hisingerite, ferrihydrite, and halloysite. These alteration products are present as intimate mixtures that vary across depositional sites, demonstrating the dynamic nature of the secondary assemblage from source to sink. This work has implications for Mars, where, for example, basalt-sourced sedimentary rocks from Gale crater are abundant in clay minerals and amorphous materials. Finally, this work underpins the importance of using high-resolution techniques, a coordinated methodology, and developing innovative approaches for future planetary sample return missions (e.g., Mars sample return).

36 MATERIALS SCIENCE↗
DOE OSTI2025

Non-traditional stable isotope measurements using laser desorption Orbitrap mass spectrometry: Implications for planetary missions.

Isotopic fractionation recorded in planetary materials provides insights into physical, chemical, and/or potential biological processes occurring on Solar System bodies. As we enter into the next decades of planetary exploration, the crucial information revealed by isotopic compositions of rocky and icy samples mandates that next generation spaceflight instrumentation possess the capability to measure isotope ratios in situ with sufficient precision/accuracy to distinguish between such processes. Here, in addition to identifying and fingerprinting complex organic materials with high accuracy and ultrahigh mass resolutions, laser desorption Orbitrap™ mass spectrometry (LD-O-MS) has the capability to determine the elemental and isotopic composition of solid planetary materials such as rock, regolith, organics, ice, etc. Here, we use a space-qualified LD-O-MS instrument comprising a 266 nm ultraviolet (UV) laser and Orbitrap mass analyzer ruggedized for planetary applications to investigate the stable isotopic composition of Ti and Zn metal plates. Based on the isotopic analyses, we constrain the performance of the CORALS instrument to sub per mille (‰) level accuracy and precision for Ti and at the per mille (‰) level for Zn. An LD-O-MS instrument is a versatile instrument capable of measuring isotopic composition of a variety of planetary samples and would constitute a critical instrument in the exploration of various planetary bodies including but not limited to Moon, Mars, Enceladus and other ocean or icy worlds, Ceres and other asteroids, and comets, thereby answering several high-priority questions pertaining to the formation and evolution of our Solar System.

58 GEOSCIENCES↗
DOE OSTI2024

EGS Collab Experiment 2: Microseismic Monitoring

This dataset contains continuous seismic waveform data recorded during stimulation and thermal circulation tests for the Enhanced Geothermal Systems (EGS) Collab Experiment #2, conducted from February to September 2022 at the Sanford Underground Research Facility in Lead, South Dakota. This experiment aimed to study and validate models of geothermal systems by injecting high-pressure fluids into rock formations 1200-1500 meters below the surface, inducing microseismic events. The seismic monitoring system included 16 three-component accelerometers and a 24-channel hydrophone array, installed in boreholes surrounding the test area. Data were recorded at high sampling rates using a continuous waveform recording system to monitor seismic activity in real time. The dataset contains the raw data stored in binary format, with files named based on timestamps, and includes calibration certificates for some sensors to facilitate corrections to real units. Users are strongly advised to consult the accompanying detailed report, which outlines the experimental setup, sensor specifications, installation procedures, and data processing methods. The report also describes important nuances, such as the hardware filters on hydrophones, sensor calibration details, and the naming conventions for the recorded data. Proper use of this dataset may require familiarity with seismic data analysis tools, such as the Obspy Python package, and an understanding of the SEED naming conventions used for channel identification.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Large-Angle Rocking Beam Electron Diffraction of Large Unit Cell Crystals Using Direct Electron Detector

We report a large-angle rocking beam electron diffraction (LARBED) technique for electron diffraction analysis. Diffraction patterns are recorded in a scanning transmission electron microscope (STEM) using a direct electron detector with large dynamical range and fast readout. We use a nanobeam for diffraction and perform the beam double rocking by synchronizing the detector with the STEM scan coils for the recording. Using this approach, large-angle convergent beam electron diffraction (LACBED) patterns of different reflections are obtained simultaneously. By using a nanobeam, instead of a focused beam, the LARBED technique can be applied to beam-sensitive crystals as well as crystals with large unit cells. Here, this paper describes the implementation of LARBED and evaluates the performance using silicon and gadolinium gallium garnet crystals as test samples. We demonstrate that our method provides an effective and robust way for recording LARBED patterns and paves the way for quantitative electron diffraction of large unit cell and beam-sensitive crystals.

4DSTEM↗
DOE OSTI2025

Crystallographic Texture, Structure, and Stress Transmission in Nugget Sandstone Examined With X‐Ray Tomography and Diffraction Microscopy

Subsurface processes in sandstones are controlled by porosity, permeability, and deformation mechanisms, all of which are controlled by a complex interplay of crystallographic rock texture, structure, and micromechanics. Texture, structure, and micromechanics have historically been studied using optical and electron microscopy of thin-sections. Here, we employed a new combination of in situ X-ray tomography and ray diffraction microscopy to study crystallographic texture, structure, and grain stresses in 3D. We examined these features in a sample of Nugget sandstone, a sandstone constituting hydrocarbon reservoirs across the American West. Our aims are threefold. First, we demonstrate the utility of X-ray diffraction microscopy probes for revealing texture, structure, and stress transmission in 3D. Second, we apply these techniques to Nugget sandstone and discuss findings in the context of prior work. Third, we study grain stress tensor evolution during mechanical compression to examine whether their heterogeneity and orientation evolution reflect that of inter-particle forces in granular materials. Our results show: (a) larger grains featured higher intra-granular misorientations, possibly from an increased prevalence of cements; (b) pores closed parallel to the loading direction and opened normal to loading; (c) grain stresses featured heterogeneity and orientations similar to inter-particle forces in non-cohesive granular materials; (d) grains featured compressive stresses in the loading direction and tensile stresses orthogonal to the loading direction, the latter resisting sample dilation and grain separation. Our work demonstrates the first known application of multi-modal X-ray tomography and diffraction microscopy to sandstone, providing new 3D insight into the nature of quartz cement and stress evolution.

high energy diffraction microscopy↗
DOE OSTI2024

Influence of Annealing Temperature on the OER Activity of NiO(111) Nanosheets Prepared via Microwave and Solvothermal Synthesis Approaches

Earth-abundant transition metal oxides are promising alternatives to precious metal oxides as electrocatalysts for the oxygen evolution reaction (OER) and are intensively investigated for alkaline water electrolysis. OER electrocatalysis, like most other catalytic reactions, is surface-initiated, and the catalyst performance is fundamentally determined by the surface properties. Most transition metal oxide catalysts show OER activities that depend on the predominantly exposed crystal facets/surface structure. Therefore, the design of synthetic strategies to obtain the most active crystal facets is of significant research interest. In this work, rock salt NiO OER catalysts with (111) predominantly exposed facets were synthesized by a solvothermal (ST) method either heated under supercritical or microwave-assisted (MW) conditions. Particular emphasis was placed on the influence of the post annealing temperature on the structural configuration and OER activity to compare their catalytic performances. The as-prepared electrocatalysts are pure α-Ni hydroxides which were converted to rock salt NiO (111) nanosheets with hexagonal pores after heat treatment at different temperatures. The OER activity of the electrodes has been evaluated in 0.1 M KOH using geometric and intrinsic current densities via normalization by the disk area and BET area, respectively. The lowest overpotential at a geometric current density of 10 mA/cm 2 is found for samples pretreated by heating between 400 and 500 °C with a catalyst loading of 115 μg/cm 2 . Despite the very similar nature of the catalysts obtained from the two methods, the ST electrodes show a higher geometric and intrinsic current density for 500 °C pretreatment. The MW electrodes, however, achieve an optimal geometric current density for 400 °C pretreatment, while their intrinsic current density requires pretreatment over 600 °C. Interestingly, pretreated electrodes show consistently higher OER activity as compared to the poorly crystalline/less ordered hydroxide as-prepared electrocatalysts. Thus, our study highlights the importance of the synthesis method and pretreatment at an optimal temperature.

36 MATERIALS SCIENCE↗