Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RON”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Combustion characteristics of diisopropoxymethane, a low-reactivity oxymethylene ether

Oxymethylene ethers (OMEs) have been studied for use as low-sooting diesel fuel additives or substitutes; very little literature discusses OMEs as spark-ignition (SI) fuels due to their typically high cetane numbers. In this work, a lower-reactivity, branched OME, diisopropoxymethane (DIPM), is evaluated to determine its effectiveness as a spark-ignition fuel, as it is the lowest-reactivity OME (as determined by Indicated Cetane Number) thus far evaluated in the literature. DIPM is synthesized in-house via acetalization from isopropanol (iPrOH) and trioxane using standard OME production practices. DIPM was then tested in a rapid compression machine (RCM) for autoignition and spark ignition characteristics, and in a modified CFR engine to determine effective octane numbers. In the RCM, an autoignition temperature sweep was performed at stoichiometric conditions from 1000/T = 1.7 - 1.0, at 5:1 inert ratio (comparable to approximately 25% EGR), where it was found that DIPM has ignition delay times 5–10x faster than isooctane and displays NTC ignition behavior. Blends with iPrOH indicate that reactivity can be matched with isooctane with low blend ratios of iPrOH in DIPM. Flame speeds were tested with a laser spark for ignition in the RCM, where the flame speed of DIPM and isooctane is determined to be comparable at engine relevant conditions. In the CFR engine, effective RON and MON based on pressure trace frequency domain measurements were determined for DIPM and a 15 vol% iPrOH in DIPM blend. Neat DIPM has (R+M)/2 = 59 and a negative sensitivity of S = -18, consistent with its NTC behavior and higher reactivity. Furthermore the DIPM/iPrOH blend has positive sensitivity and a pump-gasoline range (R+M)/2 = 89.3. DIPM on its own is unlikely to be an effective SI fuel, however, when blended with iPrOH as an ON booster, it may be a promising SI candidate fuel.

09 BIOMASS FUELS↗
DOE OSTI2024

A chemical kinetic analysis of knock propensity of methanol-to-gasoline fuel

Production of low carbon gasoline-like fuels such as methanol-to-gasoline (MTG) is a promising approach to achieve rapid greenhouse gas emission reduction of the transportation sector. Despite the fact that gasoline that meets the ASTM D4814 standard for automotive spark-ignition engine fuel can be readily produced from these processes, it is unclear how the composition of MTG may affect engine performance and emissions. Here, in this paper, a surrogate for an MTG is used to numerically study the effects of gasoline composition on knock propensity and on the sensitivity of knock to thermal and fuel stratification, to oxygen dilution and to nitric oxide from exhaust gas recirculation of residual gases. Simulations were performed in ANSYS CHEMKIN-PRO using a comprehensive chemical kinetic mechanism for gasoline surrogates, and results of the MTG surrogate were compared against those of a petroleum-based regular E10 gasoline, termed PACE-20. A premium-grade MTG fuel was also formulated by adding ethanol to the MTG surrogate, and results were compared against those of four premium-grade, gasoline-like fuels representative of future alternative gasoline formulations. Surrogates and mechanism were evaluated by comparison against experimental engine data, and the model showed high accuracy at stoichiometric conditions (mean absolute error of ignition timing equal to 1.46 crank angle degrees) but larger deviations at lean conditions (mean absolute error of ignition timing equal to 5.52 crank angle degrees). Despite the fact that the MTG surrogate has a RON 1.1 units higher than that of PACE-20, it may show higher knock propensity at medium temperature conditions due to a less intense NTC behavior. MTG autoignition was more temperature- and equivalence ratio-sensitive than that of PACE20, suggesting that MTG can benefit more from naturally-occurring thermal stratification or from induced fuel stratification of the end gas to mitigate knock intensity. The sensitivity of autoignition reactivity to oxygen dilution and to NO concentration was higher for MTG than for regular gasoline at medium loads, but the opposite trend was observed at high loads due to the effect of pressure on the low-temperature chemistry of regular gasoline. Approximately 14 % vol ethanol content was required to upgrade the octane rating of MTG from regular grade to premium grade. Adding 13.6 % vol ethanol made the fuel autoignition less sensitive to both oxygen dilution and NO content (ignition time varies approx. 17 % and 50 % less with oxygen dilution and NO addition, respectively, when adding ethanol at high engine loads).

02 PETROLEUM↗
DOE OSTI2022

Replicating HCCI-like autoignition behavior: What gasoline surrogate fidelity is needed?

This work seeks to characterize the fidelity needed in a gasoline surrogate with the intent to replicate the complex autoignition behavior exhibited within advanced combustion engines, and specifically Homogeneous Charge Compression Ignition (HCCI). A low-temperature gasoline combustion (LGTC) engine operating in HCCI mode and a rapid compression machine (RCM) are utilized to experimentally quantify fuel reactivity, through autoignition and preliminary heat release characteristics. Fuels considered include a research grade E10 U.S. gasoline (RD5-87), three multi-component surrogates (PACE-1, PACE-8, PACE-20), and a binary surrogate (PRF88.4). Each fuel was studied at lean/HCCI-like conditions covering a wide range of temperatures and pressures that are representative of naturally aspirated to high boost engine operation. Detailed chemical kinetic modeling is also undertaken using a recently updated gasoline surrogate kinetic model to simulate the RCM experiments and to provide chemical insight into surrogate-to-surrogate differences. The LGTC engine experiments demonstrate nearly identical reactivity between PACE-20 and RD5-87 across studied conditions, while faster phasing is seen for both PACE-1 and PACE-8 due to their stronger intermediate- and low-temperature heat release (ITHR/LTHR) at naturally aspirated and boosted conditions, respectively. The RCM experiments reveal typical low-temperature, negative temperature coefficient (NTC) and intermediate-temperature autoignition behaviors at all pressure conditions for RD5-87, which are qualitatively reproduced by all surrogates. Quantitative discrepancies in both autoignition and preliminary heat release are observed for all surrogates, while their ability to replicate RD5-87 autoignition behavior follows the order of PACE-20 > PACE-1 > PACE-8 > PRF88.4. Excellent mapping is obtained between the LGTC engine and the RCM, where the engine pressure-time trajectories can be characterized by the regimes represented by the RCM autoignition isopleths. The kinetic model performs commendably when simulating both autoignition and preliminary heat release of PACE-20, while typically overpredicting ignition delay times for PACE-1, PACE-8 and PRF88.4 at high-pressure and low-temperature/NTC conditions. Sensitivity and rate of production (ROP) analyses highlight surrogate-to-surrogate differences in the governing chemical kinetics where n-pentane initiates rapid OH branching at a faster rate and an earlier timing for PACE-20 than iso-pentane does for PACE-1 and PACE-8, making it computationally more reactive than the other surrogates. The current study highlights the need to include non-standardized properties, such as the lean/HCCI-like autoignition characteristics, in addition to ASTM properties (e.g., RON, MON) as metrics of fuel reactivity and targets to be matched when formulating high-fidelity surrogates that fully capture gasoline advanced combustion behavior such as HCCI-like autoignition.

42 ENGINEERING↗
DOE OSTI2023

Uncertainty quantification of a deep learning fuel property prediction model

Deep learning models are being widely used in the field of combustion. Given the black-box nature of typical neural network based models, uncertainty quantification (UQ) is critical to ensure the reliability of predictions as well as the training datasets, and for a principled quantification of noise and its various sources. Deep learning surrogate models for predicting properties of chemical compounds and mixtures have been recently shown to be promising for enabling data-driven fuel design and optimization, with the ultimate goal of improving efficiency and lowering emissions from combustion engines. In this study, UQ is performed for a multi-task deep learning model that simultaneously predicts the research octane number (RON), Motor Octane Number (MON), and Yield Sooting Index (YSI) of pure components and multicomponent blends. The deep learning model is comprised of three smaller networks: Extractor 1, Extractor 2, and Predictor, and a mixing operator. The molecular fingerprints of individual components are encoded via Extractor 1 and Extractor 2, the mixing operator generates fingerprints for mixtures/blends based on linear mixing operation, and the predictor maps the fingerprint to the target properties. Two different classes of UQ methods, Monte Carlo ensemble methods and Bayesian neural networks (BNNs), are employed for quantifying the epistemic uncertainty. Combinations of Bernoulli and Gaussian distributions with DropConnect and DropOut techniques are explored as ensemble methods. All the DropConnect, DropOut and Bayesian layers are applied to the predictor network. Aleatoric uncertainty is modeled by assuming that each data point has an independent uncertainty associated with it. The results of the UQ study are further analyzed to compare the performance of BNN and ensemble methods. Although this study is confined to UQ of fuel property prediction, the methodologies are applicable to other deep learning frameworks that are being widely used in the combustion community.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Lepidopteran mevalonate pathway optimization in Escherichia coli efficiently produces isoprenol analogs for next-generation biofuels

Terpenes constitute the largest class of natural products with over 55,000 compounds with versatile applications including drugs and biofuels. Introducing structural modifications to terpenes through metabolic engineering is an efficient and sustainable way to improve their properties. Here, in this study, we report the optimization of the lepidopteran mevalonate (LMVA) pathway towards the efficient production of isopentenyl pyrophosphate (IPP) analogs as terpene precursors. First, we linked the LMVA pathway to NudB, a promiscuous phosphatase, resulting in the production of the six-carbon analog of 3-methyl-3-buten-1-ol (isoprenol), 3-ethyl-3-buten-1-ol (C6-isoprenol). Using C6-isoprenol as the final product, we then engineered the LMVA pathway by redirecting its upstream portion from a thiolase-dependent pathway to a beta-oxidation pathway. The beta-oxidation LMVA pathway transforms valeric acid, a platform chemical that can be produced from biomass, into C6-isoprenol at a titer of 110.3 mg/L, improved from 5.5 mg/L by the thiolase LMVA pathway, which used propionic acid as a feedstock. Knockout of the E. coli endogenous thiolase genes further improved the C6-isoprenol titer to 390 mg/L, implying efficient production of homo isopentenyl pyrophosphate (HIPP). The beta-oxidation LMVA-NudB pathway also converts butanoic acid and hexanoic acid into isoprenol and isoprenol’s seven-carbon analog, 3-propyl-3-buten-1-ol (C7-isoprenol), respectively, suggesting the beta-oxidation LMVA pathway produces IPP and C7-IPP from the corresponding fatty acids. Fuel property tests revealed the longer chain isoprenol analogs have lower water solubilities, similar or higher energy densities, and comparable research octane number (RON) boosting effects to isopentenols. This work not only optimizes the LMVA pathway, setting the basis for homoterpene biosynthesis to expand terpene chemical space, but provides an efficient pathway to produce isoprenol analogs as next-generation biofuels from sustainable feedstocks.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Flexible Zn-MOF with Rare Underlying scu Topology for Effective Separation of C6 Alkane Isomers

Adsorptive separation by porous solids provides an energy-efficient alternative for the purification of important chemical species compared to energy-intensive distillations. Particularly, the separation of linear hexane isomers from its branched counterparts is crucial to produce premium grade gasoline with high research octane number (RON). Herein, we report the synthesis of a new, flexible zinc-based metal-organic framework, [Zn 5 (μ 3 -OH) 2 (adtb) 2 (H 2 O) 5 ·5 DMA] (Zn-adtb), constructed from a butterfly shaped carboxylate linker with underlying (4,8)-connected scu topology capable of separating the C6 isomers nHEX, 3MP, and 23DMB. The sorbate-sorbent interactions and separation mechanisms were investigated and analyzed through in situ FTIR, solid state NMR measurements and computational modeling. Here these studies reveal that Zn-adtb discriminates the nHEX/3MP isomer pair through a kinetic separation mechanism and the nHEX/23DMB isomer pair through a molecular sieving mechanism. Column breakthrough measurements further demonstrate the efficient separation of linear nHEX from the mono- and dibranched isomers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Space charge limited corrections to the power figure of merit for diamond

An interpretation of the unipolar figure of merit is formulated for wide bandgap (WBG) semiconductors based on the on-state specific resistance (RON,sp) derived from the space charge limited current–voltage relationship (Mott–Gurney square law). The limitations of the traditional Ohmic R ON,sp for WBG semiconductors are discussed, particularly at low doping, while the accuracy of the Mott–Gurney based R ON,sp is confirmed by Silvaco ATLAS drift–diffusion simulations of diamond Schottky pin diodes. The effects of incomplete ionization are considered as well.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Engine Combustion System Optimization Using Computational Fluid Dynamics and Machine Learning: A Methodological Approach

Gasoline compression ignition (GCI) engines are considered an attractive alternative to traditional spark-ignition and diesel engines. Here, a Machine Learning-Grid Gradient Ascent (ML-GGA) approach was developed to optimize the performance of internal combustion engines. ML offers a pathway to transform complex physical processes that occur in a combustion engine into compact informational processes. The developed ML-GGA model was compared with a recently developed Machine Learning-Genetic Algorithm (ML-GA). Detailed investigations of optimization solver parameters and variable limit extension were performed in the present ML-GGA model to improve the accuracy and robustness of the optimization process. Detailed descriptions of the different procedures, optimization tools, and criteria that must be followed for a successful output are provided here. The developed ML-GGA approach was used to optimize the operating conditions (case 1) and the piston bowl design (case 2) of a heavy-duty diesel engine running on a gasoline fuel with a research octane number (RON) of 80. The ML-GGA approach yielded >2% improvements in the merit function, compared with the optimum obtained from a thorough computational fluid dynamics (CFD) guided system optimization. The predictions from the ML-GGA approach were validated with engine CFD simulations. This study demonstrates the potential of ML-GGA to significantly reduce the time needed for optimization problems, without loss in accuracy compared with traditional approaches.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Effects of stratification and charge cooling on combustion in a gasoline direct-injection compression ignition (GDCI) engine

With the development of low temperature engine combustion strategies, performance of gasoline-type fuels under compression ignition conditions has attracted extensive research interest. Meanwhile, for the sake of co-optimization of engines and fuels for future ground transportation, identification and evaluation of general fuel properties should be a core research priority instead of endless testing of specific fuels. In this study, the roles of fuel octane sensitivity in characterizing the ignition performance of gasoline surrogates have been systematically investigated under typical gasoline direct ignition compression ignition (GDCI) engine conditions using 3D combustion CFD simulation, especially considering the subsequent in-cylinder charge stratification and charge cooling. Two different operating conditions, high boost pressure low boost temperature (beyond-RON) case and low boost pressure high boost temperature (beyond-MON) case, were considered. By comparing with our previous zero-dimensional chemical kinetic study of gasoline surrogates in advanced compression ignition (ACI) engines, the effects of stratification and charge cooling on the combustion processes are investigated. It is found that different fuel octane sensitivities lead to slight difference in equivalence ratio stratification and charge cooling due to differences in volatility. However, fuel reactivity is still the more dominant factor than the stratification and charge cooling effects in determining combustion phasing. The present results help to justify the P-T domain framework for engine autoignition analysis of overlapping pressure-temperature trajectory with ignition delay iso-contour. Here, the results also provide useful guidance to the understanding of GCI combustion process, and to the evaluation of controlling fuel properties and the selection of alternative fuels in GCI engines.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Scalable Geometric Modeler for Overlap Detection and Resolution (ASC IC L2 Milestone 7181 FY2020 Final Review)

The final review for the FY20 Advanced Simulation and Computing (ASC) Integrated Codes (IC) L2 Milestone #7181 was conducted on August 31, 2020 at Sandia National Laboratories in Albuquerque, New Mexico. The review panel unanimously agreed that the milestone has been successfully completed. Roshan Quadros (1543) led the milestone team and various members from the team presented the results. The review panel was comprised of staff from Sandia National Laboratories Albuquerque and California that are involved with computational engineering modeling and analysis. The panel consisted of experts in the fields of solid modeling, discretization, meshing, simulation workflows, and computational analysis including personnel Brett Clark (1543, Chair); Jay Foulk (8363); Jackie Moore (1553); Ron Kensek (1341); Ed Hoffman (8753); Dan Ibanez (1443). The presentation documented the technical approach of the team and summarized the results with sufficient detail to demonstrate both the value and the completion of the milestone. A separate SAND report was also generated with more detail to supplement the presentation. The purpose of the milestone was to advance capabilities for automatically finding, displaying, and resolving geometric overlaps in CAD models.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Blunt Impact Brain Injury using Cellular Injury Criterion

The Advanced Combat Helmet (\ACH") military specification (\mil-spec") requires a helmeted magnesium (\Mg") Department of Transportation (\DOT") headform be dropped vertically, with an impact speed of 3.1 m/s (10 ft/s), onto a steel hemispherical target. The pass/fail criteria are based on translational acceleration (150 G) alone, absent of any rotational component. Without a rotational component, the specification's injury risk application is limited to skull fracture and peripheral hematomas (subdural, subarachnoid), since this translational acceleration injury risk assessment is based on the Wayne State Tolerance Curve (\WSTC"). To provide a more comprehensive view of injury for the entire brain, an alternative approach is needed. To meet this need, we worked with a larger group called PANTHER, a collaboration between national laboratories, industry, and academia. Collaborations specific to research and results presented here come from efforts led by Mr. Ron Szalkowski and Mr. Sushant Malave, Ms. Alice Fawzi, and Dr. Christian Franck. We have developed a prototypical injury risk criterion based on the neuronal response to abrupt changes in general motion (translation, rotation, or both). The cellular-based mild traumatic brain injury (\cbmTBI") criterion utilizes both the strain and strain rate of brain tissue to account for the stretch and rate of stretch that occurs throughout the brain as a result of blunt impact to the head. We conducted physical experiments of an ACH-fitted magnesium headform, which produced repeatable headform peak accelerations. Then, we developed a simulation of the experiment, and validated the simulation output with the experimental data. We then substituted the magnesium headform with a human headform, consisting of skin, muscle, bone, gray matter, white matter, cerebral-spinal fluid, membranes, vasculature, intravertebral discs, airway and sinus. We quantified brain injury risk using the cbmTBI criterion, using the current mil-spec test and a modified test. The modified mil-spec test used an inclined anvil target that was located posterior to the crown of the helmet in the axial plane. While the current mil-spec test produced brain deformation from head translation alone, the modified test produced brain deformation from head translation and rotation, which is closer to most real world and combat theater impacts (e.g., such as occur in tertiary blast exposure). Compared to the current mil-spec test, the modified test produced elevated strains in the human digital twin. These data, mapped to the cbmTBI criterion, suggest increased injury risk for blunt impacts that cause rotation and translation, rather than just translation alone. Moreover, these data may lead to a rotational performance metric, which is rooted in the biology and pathology of the brain's response to impact and blast, and which should be used to improve next-generation helmet designs.

42 ENGINEERING↗
DOE OSTI2021

Advanced Light-Duty Spark Ignition Engine Research: Co-Optimization of Fuels and Engines and Partnership to Advance Combustion Engines (FY2020 Annual Progress Report)

This report covers recent progress on research tasks that support both the Co-Optimization of Fuels and Engines (Co-Optima) initiative and the Partnership to Advance Combustion Engines (PACE) consortium. The Co-Optima tasks further the science-base needed by industry stakeholders to co-evolve the next generation of highly efficient direct injection spark ignition (DISI) engines and new gasoline-type fuels. The research emphasis is on fuel effects on multimode spark ignition (SI) engine operation, which uses traditional non-dilute stoichiometric operation for peak load and power but reverts to lean operation at lower loads to provide higher fuel economy. This work focuses on determining desirable fuel specifications in terms of well-established metrics like research octane number (RON) and motor octane number, but it also involves the assessment of new fuel metrics, including fuel sooting propensity and phi-sensitivity. The PACE task supports the development of predictive computational fluid dynamics (CFD) modeling, which promises to unlock new strategies for high-efficiency combustion while minimizing tailpipe emissions. Here, the primary fuel is a regular E10 gasoline (i.e., a regular gasoline blend containing 10% ethanol), and focus is on fuel-spray dynamics and soot emissions. Soot-formation pathways are studied to determine how the pathways change with injection strategies and the thermal state of the engine (i.e., cold-starting vs. fully warmed-up operation). This PACE task also contributed to the development of an optimal E10 gasoline surrogate fuel, as reported in detail elsewhere

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Serendipitous discovery connects grandfather and granddaughter at the Lab 60 years apart A third-generation employee learns about Los Alamos family history

The Lab’s enduring mission work means staff like Cameron Townsend are one of many family members who have careers at LANL. Cameron is her family’s third generation to work at the Lab, starting with her great grandparents, followed by her grandparents (skipping her parents), and now including her and her husband. She didn’t know about her family history at the Lab until she started working here three years ago when a typical day on the job became a serendipitous window into her family’s long history with the Lab. Cameron, who is an architect in EPC-ES: Environmental Stewardship and helps manage the Lab’s historic buildings program, was given a drawing from 1960 to aid in an assessment. The drafter’s name on the sketch: Ron Turner, her grandfather.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2023

Non-Equilibrium Plasma Interactions with Biomaterials, Biological Solutions and Tissues

Cold atmospheric pressure plasma discharges offer an abundant source of reactive oxygen and nitrogen species (RONS) at room temperature enabling unique interactions with biomaterials, biological solutions and tissues. These interactions particularly with living matter are presently an important intellectual frontier in plasma science with promising potential applications ranging from human health care to advanced biomaterial processing. Exciting case studies have been reported that illustrate the huge potential of cold atmospheric plasma technology in wound healing and cancer treatment. The interaction of plasma with conducting and dielectric biomaterials such as tissue strongly influences the plasma properties. In turn this changes the impact of the plasma on the biomaterial. Particularly in the case of living matter, liquid based solutions are ubiquitous which complicates interfacial processes. The lack of insight into the underlying mechanisms of the interaction of plasma with wounds and tumors is currently a bottleneck for the further development of the technology and gives rise to many interesting scientific questions. This project was focused on plasma properties and kinetics during plasma-biomaterial interactions. Both DC pulsed and RF driven atmospheric pressure plasma jets, extensively used by the plasma community were studied. The bio-interfaces included hydrogel as a tissue model, (saline) solutions, bacteria and virus. Plasma diagnostics used include Thomson scattering, Rayleigh scattering, Raman scattering, (two-photon absorption) laser induced fluorescence, optical emission spectroscopy, absorption spectroscopy, molecular beam mass spectrometry and fast imaging allowing to determine electron densities and temperatures, ionic species, reactive species including radicals, gas temperatures, gas composition, electric fields and solution components transferred to the gas phase.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Senior Historian Alan Carr presents Lab-wide talk on testing-Nation’s last weapons test marks 30th anniversary

Join Senior Historian Alan Carr as he presents “Introduction to Nuclear Weapons Testing, 1945 to 1992” in commemoration of the 30th anniversary of the nation’s last full-scale nuclear test. Special guest retired Los Alamos test director Ron Cosimi will offer the opening remarks. Attendees will receive an original commemorative poster and can browse a new, temporary Divider test display.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2020

Development of an Optimized Gasoline Surrogate Formulation for PACE Experiments and Simulations

New powertrain solutions are needed to address societal challenges stemming in part from a transportation sector which relies heavily on combustion of conventional hydrocarbon fuels like gasoline. One way to advance new solutions is through predictive simulations. Predictive simulations can potentially limit the extent of experimental validations, reduce time spent in engineering design cycles, unlock new strategies for high efficiency combustion with power density, and minimize tailpipe emissions. However, the simulation tools currently available are either too computationally expensive, inadequate in their accuracy, or a combination of the two. A DOE-funded consortium of national laboratories called the Partnership to Advance Combustion Engines (PACE) seeks to address this gap by rapidly delivering new knowledge and tools which enable market-competitive powertrain solutions for light-duty vehicles. Approaches to modeling combustion in powertrain systems typically incorporate computational fluid dynamics (CFD) simulations with chemical kinetic models. These CFD simulations generally use surrogate fuels featuring a limited number of existing components in a reduced kinetic model to limit computational costs. Such surrogate fuels often sacrifice matching several or more combustion and physical properties of the target gasoline fuel. Validation of surrogate fuels is also often only pursued for a small subset of standard metrics such as research or motor octane number (RON, MON). The purpose of this project is to develop an optimal E10 gasoline surrogate fuel suitable for tasks across PACE to facilitate rapid common analysis and progression toward consortium goals. This project received contributions from tasks led by eight PACE principal investigators. The project funding here reflects all tasks under Pitz, whose tasks also contributed to additional PACE projects. Based on the optimal gasoline surrogate fuel composition, a reduced chemical kinetic model will be shared with PACE researchers, industry, and the broader combustion community.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Independent Fuel Property Effects of Fuel Volatility on Low Temperature Heat Release and Fuel Autoignition (Final Report)

This Cooperative Research and Development Agreement (CRADA) project between Argonne National Laboratory (ANL), Oak Ridge National Laboratory (ORNL), and Shell Global Solutions (Shell) was initiated as part of a Directed Funding Opportunity (DFO) call for proposals from the Co-Optimization of Fuels and Engines (Co-Optima) initiative. Shell had observed that volatile fuels suppress low temperature heat release (LTHR) more than expected based on conventional gasoline autoignition metrics: research octane number (RON) and motor octane number (MON). The role of LTHR contributes to autoignition phenomena for both boosted spark ignition (BSI) and advanced compression ignition (ACI) combustion modes. ACI combustion modes are applicable to large engines in the hard-to-electrify applications such as off-road, rail, and marine. Thus, having a reliable understanding of autoignition phenomena, including being able to accurately account for the effects of fuel volatility, is particularly important as new synthetic and bio-fuel compositions are considered.This CRADA project aimed to test the hypothesis that the decreased LTHR is due to preferential evaporation of multicomponent fuels when using direct injection (DI) fueling technology, creating composition and reactivity stratification. A custom set of fuels was designed and blended to test this hypothesis by Shell, with experimental engine studies at ORNL and engine combustion modeling by ANL. However, the initial experimental findings did not show the expected effect of fuel volatility suppressing LTHR. Instead, the LTHR propensity observed was independent of the fuel volatility. Due to the unexpected experimental result, the remainder of the experimental effort was redirected to study the effect of fuel volatility on emissions under spark-ignited cold-start conditions. However, as with the LTHR experiments, the cold start effort did not show a meaningful effect of fuel volatility on cold start emissions. Meanwhile, improved engine CFD models have been developed for both LTHR and cold start operations for the Shell fuels with different volatilities. While the simulation efforts were not pursued further due to the insignificant effects of fuel volatility as shown in experiments, the models developed can be easily retooled for off-road, rail, and marine applications.

09 BIOMASS FUELS↗
DOE OSTI2020

Response to Questionnaire of Grid Control Architecture Description Document: Mission Innovation, Innovation Challenge 1. Task 5 – New Grid Control Architectures. Subtask 5.1 – Collection of Available New Grid Control Architectures

As part of Task 5 (New Grid Control Architectures) of Mission Innovation, Innovation Challenge 1, a questionnaire was provided to all countries participating in the project. In this document, PNNL has responded to the questionnaire with information regarding new grid control architectures being proposed or developed in the US. Ron Melton sent the report to all participants.

24 POWER TRANSMISSION AND DISTRIBUTION↗