Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROLLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Roll-to-Roll, Dual-Layer Slot Die Coating of Chitin and Cellulose Oxygen Barrier Films for Renewable Packaging

Cellulose and chitin are the two most abundant naturally produced biopolymers and are being extensively studied as candidates for renewable oxygen barrier films used in packaging. It has been shown that bilayers formed from cellulose nanocrystals (CNCs) and chitin nanofibers (ChNFs) exhibit oxygen barrier properties similar to polyethylene terephthalate (PET). However, this prior work explored only coating each layer individually in sequence through techniques such as spray coating. Here, we demonstrate the viability of dual-layer slot die coating of CNC/ChNF bilayers onto cellulose acetate (CA) substrates. The dual-layer slot die method enables significantly lower oxygen permeability versus spray coating while using a roll-to-roll system that applies the bilayer in a single pass. This work discusses suspension properties, wetting, and drying conditions required to achieve well-controlled ChNF/CNC bilayers. Spray-coated bilayer films were on average 25% thinner than the dual-layer bilayer film; however, the thickness-normalized oxygen permeability (OP) of the dual-layer-coated ChNF/CNC bilayer film on CA was 20 times better than that of the spray-coated bilayers. Additionally, it has been shown that ChNF contributes to the wetting and barrier properties. Values of OP for the slot die-coated bilayers under optimized drying conditions were as low as 1.2 cm 3 ∙μm∙m -2 ∙d -1 ∙kPa -1 , corresponding to a normalized oxygen transmission rate of 0.32 cm 3 ∙m -2 ∙d -1 at 23 °C and 50% relative humidity. It is also noted that the adhesive properties of the dual-layer coating are also improved when films are air-dried and that ChNF contributes to the wetting and barrier properties.

09 BIOMASS FUELS↗
DOE OSTI2023

Cost Estimates of Roll-to-Roll Production of Organic Light Emitting Devices for Lighting

White organic light emitting devices (WOLEDs) offerdistinct advantages as solid state lighting sources, including high energy efficiency, superior color quality,and a flexible, thin profile that can accommodate a vast array of possible fixture designs. Recent advances in device lifetime and high speed deposition suggest that mass production of WOLED panels is approaching an inflection point. To understand the tradeoffs in the volume manufacturing of WOLED lighting panels, in this work, we estimate the cost of white WOLED panel production based on vacuum and vapor phase deposition in a roll-to-roll production line envisioned to yield an annual capacity of at least 6 × 10 6 m 2 . Assuming a WOLED operating luminance at 10 klm/m 2 , we anticipate a $\$12.5$ /klm cost of a WOLED light engine that includes the cost of the current driverand packaging. With incremental reduction in material and driver costs and improved luminance, the costof WOLED lighting can be reduced to $\$6.3$ /klm in thenear term, potentially positioning WOLEDs for use innumerous premium lighting applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Uniformity, performance, and durability of roll-to-roll-coated iridium oxide electrolyzer catalyst layers

This work investigates the use of roll-to-roll coating methods for the production of iridium oxide catalyst layers for proton exchange membrane water electrolyzers. Catalyst layers were produced using two coating methods: slot die and gravure. By varying the solids content of the catalyst ink and coating process variables loadings between 0.08 and 0.64 mg Ir cm −2 were prepared with relatively high spatial uniformity. However, at loadings below 0.2 mg Ir cm −2 microscopy reveals voids in the catalyst layer due to similar length scales of catalyst agglomerates and overall layer thickness. Electrochemical testing shows that these voids do not impact initial membrane electrode assembly performance but lead to increased performance losses after potential cycling compared to spray coated catalyst layers.

08 HYDROGEN↗
DOE OSTI2023

Diffractive Multiplexing for High-Throughput Roll-to-Roll Laser Patterning of Flexible Organic Photovoltaic Modules (Final Report)

The purpose of this project is to demonstrate a cost-effective, high-throughput roll-to-roll (R2R) process for patterning of flexible, semitransparent organic photovoltaic (OPV) modules by developing diffractive optics-based laser multiplexing (DOL Multiplexing). DOL Multiplexing allows a single, high-powered laser source to perform parallel scribing across the R2R web width in a manner compatible with high process speeds. Such a process could have enormous benefits in terms of increased process speeds and reduced costs, both up-front capital costs, and long-term operational costs, over galvanometer-based step and scan methods or many-laser systems.

14 SOLAR ENERGY↗
DOE OSTI2026

Enabling Roll-to-Roll Manufacturing of Bipolar Membranes Using Microscopy

Bipolar membranes (BPMs) used for water treatment suffer from interface instabilities, causing premature failure and decreased performance. Recent research has highlighted the impacts of membrane morphology on mechanical behavior and performance. Improved material performance of thin film membranes requires enhanced transport properties coupled with better control of the mechanical characteristics to avoid premature failure of the film. Thus, morphology is a key parameter when developing and evaluating novel membrane materials. Microscopy offers unique advantages for nano-scale characterization of thin film membrane interfaces and morphologies. In this study, the interface junction of BPMs was evaluated using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). BPMs were fabricated using (1) hot pressing lamination, (2) bench-scale solution casting, and (3) roll-to-roll sequential casting (R2R). Both commercial and in-house fabricated ion exchange membranes were used in the BPMs. The BPMs were comprised of a cation exchange membrane and an anion exchange membrane with a catalyst layer sandwiched in between. Cross sectional SEM and EDX images of the membrane interface junction were compared among the different fabrication techniques and materials. The bench cast catalyst layers were nonuniform compared to the R2R and hot pressed membranes, demonstrating the importance of precise catalyst application conditions. Different thicknesses of the BPMs and individual membrane layers revealed that polymer solution concentration needs to be optimized during manufacturing. This work shows that microscopy can identify key processing parameters that affect BPM interface junction quality at the microscale to enable manufacturing of high performance BPMs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Fabricating Silver Nanowire–IZO Composite Transparent Conducting Electrodes at Roll-to-Roll Speed for Perovskite Solar Cells

This study addresses the challenges of efficient, large-scale production of flexible transparent conducting electrodes (TCEs). We fabricate TCEs on polyethylene terephthalate (PET) substrates using a high-speed roll-to-roll (R2R) compatible method that combines gravure printing and photonic curing. The hybrid TCEs consist of Ag metal bus lines (Ag MBLs) coated with silver nanowires (AgNWs) and indium zinc oxide (IZO) layers. All materials are solutions deposited at speeds exceeding 10 m/min using gravure printing. We conduct a systematic study to optimize coating parameters and tune solvent composition to achieve a uniform AgNW network. The entire stack undergoes photonic curing, a low-energy annealing method that can be completed at high speeds and will not damage the plastic substrates. The resulting hybrid TCEs exhibit a transmittance of 92% averaged from 400 nm to 1100 nm and a sheet resistance of 11 Ω/sq. Mechanical durability is tested by bending the hybrid TCEs to a strain of 1% for 2000 cycles. The results show a minimal increase (<5%) in resistance. The high-throughput potential is established by showing that each hybrid TCE fabrication step can be completed at 30 m/min. We further fabricate methylammonium lead iodide solar cells to demonstrate the practical use of these TCEs, achieving an average power conversion efficiency (PCE) of 13%. The high-performance hybrid TCEs produced using R2R-compatible processes show potential as a viable choice for replacing vacuum-deposited indium tin oxide films on PET.

14 SOLAR ENERGY↗
DOE OSTI2015

Roll to Roll Manufacturing

ORNL researchers are developing roll to roll technologies for manufacturing, automotive, and clean energy applications in collaboration with industry partners such as Eastman Kodak.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2017

Material-Process-Performance Relationships for Roll-to-Roll Coated PEM Electrodes

Roll-to-roll (R2R) coating is the most economical and highest throughput method for producing fuel cell electrodes. R2R coating encompasses many different methodologies to create uniform films on a moving web substrate. Here we explore two coating methods, gravure and slot die, to understand the impacts of each on film uniformity and performance.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Influence of Coating Method on the Performance of Roll-to-Roll Coated PEM Fuel Cell Catalyst Layers

As production of fuel cell vehicles and power systems increases there is a need to understand the process science of fuel cell manufacturing. Industrial production of polymer electrolyte membrane fuel cell (PEMFC) electrodes will rely on continuous roll-to-roll (R2R) coating methods to meet the rates needed for mass production. There are a variety of coating methods that could be used to coat catalyst layers. The different physics of each method may result in different morphologies and performance. Here we present the results of a study comparing fuel cell catalyst layers coated using two R2R coating methods: slot-die and gravure. These two methods were selected because the physics of applying the liquid to the substrate is very different between the two cases. Pt/C catalysts layers were coated directly onto carbon-fiber gas diffusion media to create gas diffusion electrodes (GDEs), without the use of a decal transfer process. These GDEs were assembled into membrane electrode assemblies (MEAs) by hot pressing to Nafion membranes. In situ performance and other electrochemical diagnostics were used to determine the influence of coating method on catalyst layer electrochemical properties. Electron microscopy was utilized to understand the influence of coating method on electrode morphology and its influence on electrochemical properties. We also explored the influence of solvent ratio to understand the potential coupling between ink formulation and coating methodology.

DIRECT ENERGY CONVERSION,MATERIALS SCIENCE↗
DOE OSTI2020

Roll-to-Roll Direct Coating of Catalyst Inks on Membrane Films: Progress and Challenges

Further development of low temperature electrolysis (LTE) systems is of importance to ensure the renewable hydrogen production for hydrogen-based energy systems. The membrane electrode assembly (MEA) is a key component of the LTE system and typically contains a catalyst coated membrane (CCM). To enable the U.S. Department of Energy's hydrogen production cost goal of $2/kg, high volume manufacturing processes will be required to lower manufacturing costs of the CCM. A promising way for high-throughput manufacturing of CCM is using roll-to-roll (R2R) methods that allow the direct coating of electrodes on membrane films. However, there are many challenges with this methodology, both in the coating process as well as with web handling. In this talk, we discuss the membrane-ink interaction by evaluating the solvent uptake of a Nafion membrane system and verify the coatability of various inks through lab-scale coatings onto this system. Furthermore, rheology and surface tension data of the ink will be discussed together with the resulting morphology of the coated electrodes. The R2R-processed CCMs will finally be analyzed using electrochemical performance data and the results put in context with the challenges that the mass production of CCMs for LTE system faces to date.

39 EE - Hydrogen and Fuel Cell Technologies (EE-3F↗
DOE OSTI2021

Influence of Ink Formulation and Drying Conditions on Ionomer Distribution in High-Performance Roll-to-Roll-Coated Gas-Diffusion Electrodes

To enable mass production of fuel cell membrane electrode assemblies (MEAs) catalyst layers production will require continuous roll-to-roll (R2R) coating processes. Gas diffusion electrodes (GDEs) are advantageous for mass production because the catalyst layer can be directely coated on the microporous layer of the gas diffusion media without the need for a decal-transfer process. It is known that the water-to-alcohol ratio in the catalyst ink influences the interactions of the ionomer with the catalyst leading to different distributions of ionomer in spray-coated catalyst layers. It is also known that during drying of colloidal mixtures, like fuel cell inks, factors such as drying rate, particle size, and agglomeration influence how the materials distribute themselves throughout the thickness of the dired film. Thus far there have only been limited studies to understand how process conditions such as ink formulation and drying temperature influence the distribution of ionomer and catalyst coated using scalable methods. This understanding is especially important for GDEs since it is known that having a sufficient amount of ionomer at the catalyst layer-membrane interface is critical for high performance. In this study we have focused on determining how the ratio of water to 1-propanol in the catalyst ink ink and drying temperature influence the distribution of ionomer throughout the thickness of the catalyst layer. Using a combination of Kelvin probe and x-ray photoelectron spectroscopy we show that an ionomer-rich surface is promoted by a higher drying rate and a water-rich catalyst ink. In contrast, a 1-propanol catalyst ink leads to a lower concentration of ionomer on the top surface. Using x-ray computed tomography, we are able to characterize the ionomer distribution throughout the thickness of the layer. We find that, in addition to promoting an ionomer-rich top surface, water-rich inks lead to a more homogenous distribution of ionomer, whereas a 1-propanol-rich ink leads to a more irregular distribution. It is found that MEA performance is improved by selecting conditions and ink formulations that promote ionomer enrichment at the top surface to facilitate a good interface with the membrane. MEAs prepared with a 75 wt% water catalyst ink with a 0.9 I/C have equivalent performance to spray-coated GDEs. Critically, these R2R-coated GDEs do not need an additional ionomer overlayer like the spray-coated GDEs do, reducing the number of processing steps in a manufacturing setting. This work shows that with the appropriate selection of materials, ink formulation, and processing conditions gas-diffusion electrodes are a viable pathway for fuel cell manufacturing.

ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATION↗
DOE OSTI2019

Influence of Rolling Temperature on the Mechanical Properties and Microstructure of Variable-Plane-Rolled Mg-3Al-1Zn Alloy

AZ31 magnesium alloy was produced via variable-plane rolling (VPR) under different temperatures. The effects of rolling temperature on the microstructure, texture and mechanical properties were investigated. A double-peak basal texture was formed during VPR treatment. Dynamic recrystallization (DRX) was observed during the VPR treatment, and it can reduce the texture intensity owing to the coalescence of sub-grains. Four types of twins were observed in the VPR treatment: {10-12} extension twins, {10-13}, {10-11} contraction twins and {10-11}-{10-12} double twins. The suitable temperature of AZ31 magnesium alloy for VPR treatment is determined as 623 K through experiments with tensile yield strength of 240 MPa, compressive yield strength of 162 MPa and elongation of 13%. Owing to the important impact of temperature on mechanical properties, the alloy was further VPRed with a decrease in temperature pass-by-pass. The high temperature of 623 K at the initial passes randomized the texture, which led to notably high ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Roll-to-roll solvent-free manufactured electrodes for fast-charging batteries

In response to the growing demand for lithium-ion batteries (LIBs), we demonstrate a solvent-free manufacturing technology that can avoid toxic organic solvents and form unique electrode structures to overcome the bottlenecks in low costs and fast charging. The lower tortuosity achieved by the open pores in the dry-printed (DP) electrode allows for a shorter Li+ diffusion pathway, which leads to better rate performance. The DP pouch cells exhibit higher capacity retention of 78% and 69% at 3C and 4C, respectively, compared with 67% and 52% for the slurry cast (SL) cells at the same rates. Moreover, the coating layer on the surface of active materials prevents the excess side reaction between active materials and electrolytes, which prolongs the cycle life of the DP cells. This manufacturing process is a roll-to-roll system with immense potential to be scaled up, providing a more efficient and economical way for battery manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Multi-technique characterization of spray coated and roll-to-roll coated gas diffusion fuel cell electrodes

Here this work reports the characterization of catalyst layer (CL) structure and composition for a set of gas-diffusion electrodes (GDEs) fabricated by different coating methods with the goal of developing a better understanding of CL processing-structure-property-performance relationships. The CL coating techniques used in this study were ultrasonic spray coating, and two roll-to-roll (R2R) methods - gravure and slot die. Scanning transmission electron microscopy (STEM) coupled with X-ray energy dispersive spectroscopy (EDS) analysis of GDE cross-sections provided bulk information, while scanning electron microscopy (SEM) with EDS and X-ray photoelectron spectroscopy (XPS) were used to investigate the near surface and surface composition of the CLs that will be in direct contact with the membrane once the membrane electrode assembly (MEA) is constructed. This study demonstrates that common quantification parameters, namely the F:Pt ratio extracted from cross-sectional STEM-EDS maps and top-down CL measurements with SEM and XPS, along with roughness parameters quantified from SEM micrographs are useful parameters in explaining and potentially predicting performance trends. Additionally, it highlights the importance of understanding key CL surface properties for advancing the manufacturability of high-performance components for polymer electrolyte membrane (PEM) technologies.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2019

Elastohydrodynamics of roll-to-roll UV-cure imprint lithography

Inextensible cylindrical shell theory and lubrication theory combine into a model for the elastohydrodynamics of a rolling-imprint modality of nanoimprint lithography (NIL). Foil-bearing theory describes the formation of the lubrication gap due to relative motion between a tensioned substrate and a rigid, cylindrical surface. Reproduction of the results of foil-bearing theory for both stiff and perfectly-flexible substrates validates this coupled model and reveals a highly predictable region of uniformity that provides low shear stress conditions ideal for UV-cure. Here, these results show theoretical limitations that are used to construct an operating window for predicting rolling-mode NIL process feasibility.

42 ENGINEERING↗
DOE OSTI2019

Roll-to-Roll Scalable Production of Ordered Microdomains through Nonvolatile Additive Solvent Annealing of Block Copolymers

A new method, “nonvolatile solvent vapor annealing” (NVASA), has been developed to anneal block copolymers during film deposition by controlling the solvent drying process. Precise amounts of high boiling point additive added to the polymer solution briefly remain in the polymer film after casting, leaving the film in a swollen state, increasing its chain mobility, and ultimately improving domain order. We demonstrated the effectiveness of NVASA on several block copolymer systems and used in situ grazing incidence small-angle X-ray scattering (GISAXS) to validate the ordering process during the self-assembly. The simplicity and reproducibility of the method is attractive for implementation in large-scale manufacturing processes such as roll-to-roll printing as swell ratio is easily controlled by the amount of additive used and separate annealing steps are not needed. This work potentially introduces a new way to quickly and cost effectively anneal block copolymers.

36 MATERIALS SCIENCE↗