Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RANGE CONTROL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Nonequilibrium atmospheric pressure plasma jet using a combination of 50 kHz/2 MHz dual-frequency power sources

An atmospheric pressure plasma jet is generated by dual sinusoidal wave (50 kHz and 2 MHz). The dual-frequency plasma jet exhibits the advantages of both low frequency and radio frequency plasmas, namely, the long plasma plume and the high electron density. The radio frequency ignition voltage can be reduced significantly by using dual-frequency excitation compared to the conventional radio frequency without the aid of the low frequency excitation source. A larger operating range of α mode discharge can be obtained using dual-frequency excitation which is important to obtain homogeneous and low-temperature plasma. A larger controllable range of the gas temperature of atmospheric pressure plasma could also be obtained using dual-frequency excitation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

GaAs dual-gate FET for operation up to K-band

A high-frequency equivalent-circuit model of a GaAs dual-gate FET and analytical expressions for the input/output impedances, transconductance, unilateral gain, and stability factor are presented. It is found that the gain of a dual-gate FET is higher than of a single-gate FET at low frequency but decreases faster as frequency increases because of the capacitive shunting effect of the second gate. A dual-gate power FET suitable for variable-gain-amplifier applications up to K-band has been developed. At 10 GHz, a 1.2-mm-gatewidth device has achieved an output power of 1.1 W with 10.5-dB gain and 31-percent power-added efficiency. At 20 GHz, the same device delivered an output power of 340 mW with 5.3-dB gain. At K-band, a dynamic-gain control range of up to 45 dB was obtained with an insertion phase change of no more than + or 2 degrees for the first 10 dB of gain control.

Kim, B.↗

ISS Payload Racks Automated Flow Control Calibration Method

Payload Racks utilize MTL and/or LTL station water for cooling of payloads and avionics. Flow control range from valves of fully closed, to up to 300 Ibmhr. Instrument accuracies are as high as f 7.5 Ibm/hr for flow sensors and f 3 Ibm/hr for valve controller, for a total system accuracy of f 10.5 Ibm/hr. Improved methodology was developed, tested and proven that reduces accuracy of the commanded flows to less than f 1 Ibmhr. Uethodology could be packed in a "calibration kit" for on- orbit flow sensor checkout and recalibration, extending the rack operations before return to earth. -

Simmonds, Boris G.↗

Pterodactyl: Guidance and Control of a Symmetric Deployable Entry Vehicle using an Aerodynamic Control System

The NASA-funded Pterodactyl project seeks to advance the current state-of-the-art for entry vehicles by developing novel guidance and control technologies for Deployable Entry Vehicles (DEVs). This paper presents the guidance and control design and analysis for a mechanically-deployed DEV with a symmetric aeroshell and aerodynamic control surfaces. We present guidance tuning using both bank angle modulation with the Fully-Numerical Predictor Corrector Entry Guidance technique (FNPEG) and angle of attack and sideslip modulation with FNPEG with uncoupled range control (FNPEG URC). We show the control system design and simulation results for tracking both types of guidance commands.

Benjamin W L Margolis↗

Pterodactyl: Guidance and Control of a Symmetric Deployable Entry Vehicle using an Aerodynamic Control System

The NASA-funded Pterodactyl project seeks to advance the current state-of-the-art for entry vehicles by developing novel guidance and control technologies for Deployable Entry Vehicles (DEVs). This paper presents the guidance and control design and analysis for a mechanically-deployed DEV with a symmetric aeroshell and aerodynamic control surfaces. We present guidance tuning using both bank angle modulation with the Fully-Numerical Predictor Corrector Entry Guidance technique (FNPEG) and angle of attack and sideslip modulation with FNPEG with uncoupled range control (FNPEG URC). We show the control system design and simulation results for tracking both types of guidance commands.

Benjamin Margolis↗

Feed-Forward Compensation for Model Predictive Control in Tri-port Current-Source Medium-Voltage String Inverters for PV-Plus-Storage Farms

The novel tri-port current-source medium-voltage string inverter (TCS-MVSI) is a promising candidate for large-scale PV-plus-storage (PVS) farms owing to its galvanic isolation, easy storage integration, soft-switching capability across entire load range, controlled low dv/dt and EMI, benign fault tolerance, etc. Due to its low inertia feature, traditional PI-based control cannot manage large transients effectively. Instead, a model-based predictive control (MPC) is proposed to achieve robust and stable operation. As is well known, the control performance of MPC is compromised by the sampling and computational delay during implementation significantly, if not well addressed. This paper analyzed and quantified these delays and then proposes feed-forward compensation (FFC) for the MPC method to compensate the delays and the large parameter variations due to the low-inertia nature. In addition, this method also compensates for the high dc-link ripple within each switching cycle, a unique issue for low-inertia converters. Here, the proposed method requires low computational effort, allowing it to be extended for multiple ports. The effectiveness of the proposed method has been validated in experiments. In 10 kW test, the proposed method decreases the average dc-link current by 17%, leading to ~20% conduction losses and ~0.5% increase in converter efficiency. In addition, the peak dc-link current also decreases by 15%, resulting in reduced transformer size. As a result, an increased power density can be achieved with the proposed method. Similar improvements have been observed across the power range from 2 kW to 10 kW.

30 DIRECT ENERGY CONVERSION↗

Radar-Data-Processing System

Report describes radar data system at NASA Western Aeronautical Test Range. System provides real-time and recorded data about flightpaths of research aircraft and Space Shuttle. Called RADATS, processes data from three radars simultaneously; interacts with system operator; enhances data by introducing corrections and smoothing; controls range, azimuth, and elevation of radars; and automatically calibrates itself before and after missions. Software classified into three kinds of programs: utility, real-time, and calibration. Equipment exhibited exceptional reliability. Software matured to become virtually trouble-free.

Anderson, Karl F.↗

Ablation of biological tissues by radiation of strontium vapor laser

A two-stage laser system consisting of a master oscillator and a power amplifier based on sources of self- contained transitions in pairs SrI and SrII has been developed. The radiation spectrum contains 8 laser lines generating in the range of 1 – 6.45 μm, with a generation pulse length of 50 – 150 ns, and pulse energy of ∼ 2.5 mJ. The divergence of the output beam was close to the diffraction and did not exceed 0.5 mrad. The control range of the laser pulse repetition rate varied from 10 to 15 000 Hz. The given laser system has allowed to perform ablation of bone tissue samples without visible thermal damage.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Analysis of a fixed-pitch X-wing rotor employing lower surface blowing

Lower surface blowing (LSB) is investigated as an alternative to the variable blade pitch requirement for the X-wing Circulation Control (CC) rotor concept. Addition trailing edge blowing slots on the lower surfaces of CC airfoils provide a bidirectional lift capability that effectively doubles the control range. The operational requirements of this rotor system are detailed and compared to the projected performance attributes of LSB airfoils. Analysis shows that, aerodynamically, LSB supplies a fixed pitch rotor system with the equivalent lift efficiency and rotor control of present CC rotor designs that employ variable blade pitch. Aerodynamic demands of bidirectional lift production are predicted to be within the capabilities of current CC airfoil design methodology. Emphasis in this analysis is given to the high speed rotary wing flight regime unique to stoppable rotor aircraft. The impact of a fixed pitch restriction in hover and low speed flight is briefly discussed.

Schwartz, Alan W.↗

Gain-Compensating Circuit For NDE and Ultrasonics

High-frequency gain-compensating circuit designed for general use in nondestructive evaluation and ultrasonic measurements. Controls gain of ultrasonic receiver as function of time to aid in measuring attenuation of samples with high losses; for example, human skin and graphite/epoxy composites. Features high signal-to-noise ratio, large signal bandwidth and large dynamic range. Control bandwidth of 5 MHz ensures accuracy of control signal. Currently being used for retrieval of more information from ultrasonic signals sent through composite materials that have high losses, and to measure skin-burn depth in humans.

Kushnick, Peter W.↗

The 30-GHz monolithic receive module

The fourth year progress is described on a program to develop a 27.5 to 30 GHz GaAs monolithic receive module for spaceborne-communication antenna feed array applications, and to deliver submodules for experimental evaluation. Program goals include an overall receive module noise figure of 5 dB, a 30 dB RF to IF gain with six levels of intermediate gain control, a five bit phase shifter, and a maximum power consumption of 250 mW. Submicron gate length single and dual gate FETs are described and applied in the development of monolithic gain control amplifiers and low noise amplifiers. A two-stage monolithic gain control amplifier based on ion implanted dual gate MESFETs was designed and fabricated. The gain control amplifier has a gain of 12 dB at 29 GHz with a gain control range of over 13 dB. A two-stage monolithic low noise amplifier based on ion implanted MESFETs which provides 7 dB gain with 6.2 dB noise figure at 29 GHz was also developed. An interconnected receive module containing LNA, gain control, and phase shifter submodules was built using the LNA and gain control ICs as well as a monolithic phase shifter developed previously under this program. The design, fabrication, and evaluation of this interconnected receiver is presented. Progress in the development of an RF/IF submodule containing a unique ion implanted diode mixer diode and a broadband balanced mixer monolithic IC with on-chip IF amplifier and the initial design of circuits for the RF portion of a two submodule receiver are also discussed.

Bauhahn, P.↗

Simulation and analysis of grating-integrated quantum dot infrared detectors for spectral response control and performance enhancement

We propose and analyze a novel detector structure for pixel-level multispectral infrared imaging. More specifically, we investigate the device performance of a grating-integrated quantum dots-in-a-well photodetector under backside illumination. Our design uses 1-dimensional grating patterns fabricated directly on a semiconductor contact layer and, thus, adds a minimal amount of additional effort to conventional detector fabrication flows. We show that we can gain wide-range control of spectral response as well as large overall detection enhancement by adjusting grating parameters. For small grating periods, the spectral responsivity gradually changes with parameters. We explain this spectral tuning using the Fabry–Perot resonance and effective medium theory. For larger grating periods, the responsivity spectra get complicated due to increased diffraction into the active region, but we find that we can obtain large enhancement of the overall detector performance. In our design, the spectral tuning range can be larger than 1 μm, and, compared to the unpatterned detector, the detection enhancement can be greater than 92% and 148% for parallel and perpendicular polarizations. Our work can pave the way for practical, easy-to-fabricate detectors, which are highly useful for many infrared imaging applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Pterodactyl: 6-DOF Integration of Guidance and Control Algorithms in Genesis

The NASA-funded Pterodactyl project seeks to advance the current state-of-the-art for entry vehicles by developing novel guidance and control technologies for Deployable Entry Vehicles. This paper builds upon the Pterodactyl architecture that employed eight individually articulating flaps with two options for guidance, bank angle modulation with the Fully Numerical Predictor Corrector Entry Guidance (FNPEG) technique and angle of attack and sideslip modulation with FNPEG uncoupled range control. These, with a linear quadratic regulator controller, have previously been presented in separate 3-DOF trajectory simulations, one for translational motion and another for rotational dynamics. This work will show results for integrated 6-DOF simulations, leveraging recent advancements in trajectory simulation tools, namely the Julia-based Genesis flight simulation tool. Results show similar performance for both schemes when compared to the previously presented 3-DOF results once the controllers were adequately tuned. Angle of attack and sideslip angle modulation necessitated a controller designed at high dynamic pressure conditions, and bank angle modulation necessitated a controller designed at lower dynamic pressure conditions. Notably, the angle of attack and sideslip modulation approach could not achieve the parachute deploy point target Mach number of 2, when only tuning the controller gains, so future work will be needed to improve guidance and control tracking.

EDL↗

Characterization of NbN films for superconducting nanowire single photon detectors

Nanoscopic superconducting meander patterns offer great promise as a new class of cryogenic radiation sensors capable of single photon detection. To realize this potential, control of the superconducting properties on the nanoscale is imperative. To this end, Superconducting Nanowire Single Photon Detectors (SNSPDs) are under development by means Energetic Neutral Atom Beam Lithography and Epitaxy, or ENABLE. ENABLE can growth highly-crystalline, epitaxial thin-film materials, like NbN, at low temperatures; such wide-ranging control of fabrication parameters is enabling the optimization of film properties for single photon detection. T{sub c}, H{sub c2}, {zeta}{sub GL} and J{sub c} of multiple thin films and devices have been studied as a function of growth conditions. The optimization of which has already produced devices with properties rivaling all reports in the existing literature.

36 MATERIALS SCIENCE↗

The physiology of spacecraft and space suit atmosphere selection

Factors which are considered in arriving at control values and control ranges of the parameters established for spacecraft and space suit environments include physiological, engineering, operational cost, and safety considerations. A number of physiological considerations are discussed, including hypoxia and hyperoxia, hypercapnia, temperature regulation, and decompression sickness. The impact of these considerations on space craft and space suit atmosphere selection is considered. The past experience in controlling these parameters in the U.S. and Soviet spacecraft and space suits and the associated physical responses are also reviewed. Physiological factors currently under investigation are discussed, including decompression sickness.

Waligora, J. M.↗

Improvement of Prostate Treatment by Anterior Proton Fields

Purpose: We performed a treatment planning study to demonstrate the potential dosimetric benefits of anterior-oriented fields for prostate irradiation by proton beam. A novel in vivo beam range control method shows millimeter accuracy, suggesting that such fields could be safely used to spare the rectum given the sharp distal penumbra of protons. Methods and Materials: Ten prostate patients treated with water-filled endorectal balloon were selected. Bilateral fields were planned following the conventional treatment protocol. Three anterior-oriented fields (0, +30, -30 Degree-Sign ) were planned, with the range compensators manually adjusted to improve rectal sparing. Dose distributions to the clinical target volume, rectum, anterior rectal wall (ARW), bladder, bladder wall (BW), and femoral heads were compared for: A) equally weighted bilateral fields, B) a single straight anterior field, and C) two equally weighted anterior-oblique fields. Results: The anterior-oriented fields required much less beam energy, {approx}10 cm water equivalent path length less than lateral fields. For ARW, the V{sub 95%} for Plans A, B, and C were 39%, 8%, and 6%, respectively; the corresponding V{sub 80%} were 59%, 27%, and 26%, respectively (p = 0.002 when Plan A was compared with B or C). Plan B irradiated a larger volume of BW than did Plan A by 3% at V{sub 95%}, 11% at V{sub 80%}, and 16% at V{sub 50%} (p = 0.002), whereas Plan C differs little from Plan A for BW at these dose levels. The femoral heads received {approx}40% of the prescription dose in Plan A, but negligible dose in Plans B and C. Conclusions: Compared to lateral fields, anterior-oriented fields can significantly reduce dose to the ARW, particularly at high dose levels. These fields alone, or in combination with lateral fields, allow for the possibility of either reducing treatment toxicity at current prescription doses or further dose escalation in the treatment of prostate cancer.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Deep Eutectic Solvent Extraction of High-Purity Lignin from a Corn Stover Hydrolysate

Here, a lactic acid/chlorine chloride-based deep eutectic solvent (DES) was used for the extraction of high-purity lignin (up to 94.7%) in high yield (up to 75%) from the hydrolysis/fermentation residue corn stover hydrolysate (CSH), which was generated from a pilot-plant-scale biorefinery. A range of extraction conditions were investigated, which involved varying reaction temperature, time, and DES composition. The relationship between lignin yield, purity, and structural characteristics with DES treatment conditions was determined. The extraction of high-purity lignin from hydrolysis/fermentation residues presents a promising approach for enhancing the economic feasibility of a lignocellulose biorefinery. It was also determined that DES extraction can produce lignin with a controlled range of molecular weight and functional group content.

09 BIOMASS FUELS↗

Concepts for Autonomous Operation of Microreactors

Microreactor concepts have seen increasing interest in recent years given their potential use for meeting energy needs in remote and grid-isolated communities. Given the small power outputs of microreactors and the potential for remote siting, there is a need to reduce operational staffing levels to improve their economic viability. A key enabling technology for this purpose is autonomous control that enables autonomous operation of microreactors. While several options for autonomous control exist, the level of human operator involvement in operational decision making needs to be defined as part of the system design process. Once this separation of function is achieved, several options exist for autonomous control ranging from simple automation of some procedures to fully autonomous operational mode decision making and execution.A critical aspect of autonomous decision making is the ability to have as complete an awareness of the system state as possible. In addition to data on temperature, pressure, flow, and neutron flux, measurements of the condition of important components will be necessary. This type of information will allow the autonomous control system to adapt its decision making to any changing conditions within the reactor, thereby not compromising safety while continuing to operate for as long as possible. Several technical advances are needed before widespread use of autonomous control in microreactors. These include sensor and instrumentation technologies that are capable of long term, unattended operation in harsh environments, technologies for inferring the state of the microreactor system or subsystems in an automated fashion, algorithms for predictive decision making that account for the assessed condition of the microreactor subsystems as well as the potential impact on those components of any operational decision, and actuators and control system hardware that are also long-lived in a harsh environment. In addition, given the need to remotely monitor the operations, cybersecurity requirements will likely need to be imposed to ensure secure operations.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗