Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Performance Margins”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Evaluation of the Shuttle GN&C during powered ascent flight phase

An overview of the ascent trajectory and GN&C (guidance, navigation, and control) system design is followed by a summary of flight test results for the ascent phase of STS-1. The most notable variance from nominal pre-flight predictions was the lofted trajectory observed in first stage due to an unanticipated shift in pitch aerodynamic characteristics from those predicted by wind tunnel tests. The GN&C systems performed as expected on STS-1 throughout powered flight. Following a discussion of the software constants changed for Flight 2 to provide adequate performance margin, a summary of test results from STS-2 and STS-3 is presented. Vehicle trajectory response and GN&C system behavior were very similar to STS-1. Ascent aerodynamic characteristics extracted from the first two test flights were included in the data base used to design the first stage steering and pitch trim profiles for STS-3.

Olson, L.↗
NASA NTRS1983

Contamination control plan for prelaunch operations

A unified, systematic plan is presented for contamination control for space flight systems. Allowable contaminant quantities, or contamination budgets, are determined based on system performance margins and system-level allowable degradations. These contamination budgets are compared to contamination rates in ground environments to establish the controls required in each ground environment. The use of feedback from contamination monitoring and some contamination control procedures are discussed.

Austin, J. D.↗
NASA NTRS1985

Space Shuttle main engine product improvement

The current design of the Space Shuttle Main Engine has passed 11 certification cycles, amassed approximately a quarter million seconds of engine test time in 1200 tests and successfully launched the Space Shuttle 17 times of 51 engine launches through May 1985. Building on this extensive background, two development programs are underway at Rocketdyne to improve the flow of hot gas through the powerhead and evaluate the changes to increase the performance margins in the engine. These two programs, called Phase II+ and Technology Test Bed Precursor program are described. Phase II+ develops a two-tube hot-gas manifold that improves the component environment. The Precursor program will evaluate a larger throat main combustion chamber, conduct combustion stability testing of a baffleless main injector, fabricate an experimental weld-free heat exchanger tube, fabricate and test a high pressure oxidizer turbopump with an improved inlet, and develop and test methods for reducing temperature transients at start and shutdown.

Lucci, A. D.↗
NASA NTRS1990

Flight motor set 36OH005 (STS-28R). Volume 5: (Nozzle component)

A review of the performance and post flight condition of the STS-28 redesigned solid rocket motor (RSRM) nozzles is presented in this document. Applicable discrepancy reports (DR's) and process departures (PD's) are presented in section 5.0. The nozzle component program team (NCPT) performance evaluation and the redesign program review board (RPRB) assessment is included in section 6.0. The STS-28 nozzle assemblies were flown on the RSRM fifth flight (Space Shuttle Columbia). The nozzles were a partially submerged convergent/divergent movable design with an aft pivot point flexible bearing. The nozzle assemblies incorporated the following features: (1) RSRM forward exit cone with snubber assembly; (2) RSRM fixed housing; (3) structural backup outer boot ring (OBR); (4) RSRM cowl ring; (5) RSRM nose inlet assembly; (6) RSRM throat assembly; (7) RSRM forward nose and aft inlet ring; (8) RSRM aft exit cone assembly with linear-shaped charge (LSC); (9) RTV backfill in joints 1, 3, and 4; (10) use of EA913 NA adhesive in place of EA913; (11) redesigned nozzle plug; and (12) carbon cloth phenolic (CCP) with 750 ppm sodium content. The RSRM fifth flight test objectives are as follows: (1) verify that flexible bearing seals operate within the specified temperature range; (2) verify that flexible bearing maintained a positive gas seal between its internal components; (3) inspect flexible bearing for damage due to water impact; (4) verify performance of the nozzle liner; (5) verify that nozzle parts are reusable; (6) verify through flight demonstration and a postflight inspection that the flexible bearing is reusable; (7) verify by inspection the remaining nozzle ablative thicknesses; and (8) verify the nozzle performance margins of safety.

Smith, Dan M., Jr.↗
NASA NTRS1992

Hypersonic vehicle control law development using H infinity and mu-synthesis

Applicability and effectiveness of robust control techniques to a single-stage-to-orbit (SSTO) airbreathing hypersonic vehicle on an ascent accelerating path and their effectiveness are explored in this paper. An SSTO control system design problem, requiring high accuracy tracking of velocity and altitude commands while limiting angle of attack oscillations, minimizing control power usage and stabilizing the vehicle all in the presence of atmospheric turbulence and uncertainty in the system, was formulated to compare results of the control designs using H infinity and mu-synthesis procedures. The math model, an integrated flight/propulsion dynamic model of a conical accelerator class vehicle, was linearized as the vehicle accelerated through Mach 8. Controller analysis was conducted using the singular value technique and the mu-analysis approach. Analysis results were obtained in both the frequency and the time domains. The results clearly demonstrate the inherent advantages of the structured singular value framework for this class of problems. Since payload performance margins are so critical for the SSTO mission, it is crucial that adequate stability margins be provided without sacrificing any payload mass.

Gregory, Irene M.↗
NASA NTRS1991

Proximity operations considerations affecting spacecraft design

Proximity operations can be defined as the maneuvering of two or more spacecraft within 1 nautical mile range, with relative velocity less than 10 feet per second. The passive vehicle is nontranslating and should provide for maintenance of the desired approach attitude. It must accommodate the active (translating) vehicle induced structural loads and performance characteristics (mating hardware tolerances), and support sensor compatibility (transponder, visual targets, etc.). The active vehicle must provide adequate sensor systems (relative state information, field-of-view, redundancy), flight control hardware (thruster sizing, minimal cross-coupling, performance margins, redundancy) and software (reconfigurable, attitude/rate modes, translation and rotation fine control authority) characteristic, and adequate non-propulsive consumables such as power. Operational concerns must be considered. These include the following: (1) the desired approach trajectory and relative orientation; (2) the active vehicle thruster plume effects (forces, torques, contamination) on the passive vehicle; and (3) procedures for contingencies such as loss of communications, sensor or propulsion failures, and target vehicle loss of control.

Staas, Steven K.↗
NASA NTRS1992

Environmental Verification Experiment for the Explorer Platform (EVEEP)

Satellites and long-life spacecraft require effective contamination control measures to ensure data accuracy and maintain overall system performance margins. Satellite and spacecraft contamination can occur from either molecular or particulate matter. Some of the sources of the molecular species are as follows: mass loss from nonmetallic materials; venting of confined spacecraft or experiment volumes; exhaust effluents from attitude control systems; integration and test activities; and improper cleaning of surfaces. Some of the sources of particulates are as follows: leaks or purges which condense upon vacuum exposure; abrasion of movable surfaces; and micrometeoroid impacts. The Environmental Verification Experiment for the Explorer Platform (EVEEP) was designed to investigate the following aspects of spacecraft contamination control: materials selection; contamination modeling of existing designs; and thermal vacuum testing of a spacecraft with contamination monitors.

Norris, Bonnie↗
NASA NTRS1991

An algorithm to design a multiple-channel communications system

The authors present a novel algorithm to design a phase-modulated residual carrier communications system for optimum performance. The algorithm has been developed as an aid in the design of two telemetry data channels operating simultaneously with a turn-around ranging signal. The algorithm provides the selection of an optimum subcarrier frequency and modulation indices for minimizing the mutual interferences among the channels to achieve desired link performance margins. The set of modulation indices provided by this algorithm will also achieve an optimum power division between the carrier, the ranging and the high data rate and low data rate channels. Finally, a software program using this algorithm has been developed for use with personal computers. This program provides the computation of the optimum subcarrier frequencies and modulation indices for a standard case that is recommended by the international Consultative Committee for Space Data Systems.

Nguyen, Tien M.↗
NASA NTRS1992

Hypersonic vehicle control law development using H infinity and mu-synthesis

Applicability and effectivness of robust control techniques to a single-stage-to-orbit (SSTO) airbreathing hypersonic vehicle on an ascent accelerating path and their effectivness are explored in this paper. An SSTO control system design problem, requiring high accuracy tracking of velocity and altitude commands while limiting an angle of attack oscillations, minimizing control power usage and stabilizing the vehicle all in the presence of atmospheric turbulence and uncertainty in the system, was formulated to compare results of the control designs using H infinity and mu-synthesis procedures. The math model, an integrated flight/propulsion dynamic model of a conical accelerator class vehicle, was linearized as the vehicle accelerated through Mach 8. Controller analysis was conducted using the singular value technique and the mu-analysis approach. Analysis results were obtained in both the frequency and the time domains. The results clearly demonstrate the inherent advantages of the structured singular value framework for this class of problems. Since payload performance margins are so critical for the SSTO mission, it is crucial that adequate stability margins be provided without sacrificing any payload mass.

Gregory, Irene M.↗
NASA NTRS1993

Evaluation of the national launch system as a booster for the HL-20

The capability of a proposed national launch system (NLS) to boost the personnel launch system (PLS) manned vehicle has been examined. A reference NLS configuration, the NLS-2 1.5 stage vehicle, and a reference HL-20 PLS configuration were used for the study. Performance has been analyzed for several PLS insertion orbits to support the Space Station Freedom resupply mission. The reliability of the NLS launch vehicle and its contribution to crew safety requirements have been determined. The launch-processing and launch facility requirements of these combined systems were also analyzed. Previous studies of these two systems have focused on either the PLS manned element or NLS launch vehicle. This paper combines the results of prior studies in an analysis of the integrated NLS/PLS configuration. This analysis has found the proposed NLS 1.5 stage launch vehicle to be an excellent booster for the PLS. Predicted performance margins for this launch-vehicle configuration are more than adequate, and acceptable reliability and safety levels are anticipated. Integration of this NLS/PLS configuration into NASA mixed-fleet launch architectures is feasible.

Duffy, James B.↗
NASA NTRS1993

The impact of flying qualities on helicopter operational agility

Flying qualities standards are formally set to ensure safe flight and therefore reflect minimum, rather than optimum, requirements. Agility is a flying quality but relates to operations at high, if not maximum, performance. While the quality metrics and test procedures for flying, as covered for example in ADS33C, may provide an adequate structure to encompass agility, they do not currently address flight at high performance. This is also true in the fixed-wing world and a current concern in both communities is the absence of substantiated agility criteria and possible conflicts between flying qualities and high performance. AGARD is sponsoring a working group (WG19) title 'Operational Agility' that deals with these and a range of related issues. This paper is condensed from contributions by the three authors to WG19, relating to flying qualities. Novel perspectives on the subject are presented including the agility factor, that quantifies performance margins in flying qualities terms; a new parameter, based on maneuver acceleration is introduced as a potential candidate for defining upper limits to flying qualities. Finally, a probabilistic analysis of pilot handling qualities ratings is presented that suggests a powerful relationship between inherent airframe flying qualities and operational agility.

Padfield, Gareth D.↗
NASA NTRS1993

Combustion for future supersonic transport propulsion

Even with it's marginal performance, Concorde has demonstrated that supersonic civil aircraft are a practical proposition. A second generation machine will need sufficiently good performance for a robust operating system that can provide reliable, frequent service with competitive economics. Additionally, the propulsion system must be acceptable environmentally. That is it must create acceptable noise levels around airports and have acceptable emissions throughout its mission including cruise. Whatever devices may be used to improve the acceptability at subsonic flight conditions, the high operating temperatures at cruise can create difficult targets for the operation of the combustion system both mechanically and in the combustion process itself. While the driving force is ever better fuel consumption and weight to achieve economic viability, a future supersonic transport engine will have cycle temperatures limited only by the mechanical integrity of the major components. The environment of the major components in modern gas turbine engines is dominated by the air delivered by the compressor system. Consequently the maximum compression temperature is governed by materials available for the turbine and compressor discs. The continued improvement of the disc material leads to combustion inlet temperatures beyond today's experience and sets difficult targets for combustion system emissions. This is worsened by the requirement being at cruise and therefore maintained for the major part of the mission. Problems such as creep and oxidation of metallic parts are also considered.

B. W. Lowrie↗
NASA NTRS1994

Bolt cutter functional evaluation

The Aerospace Corporation has been implementing finite difference and finite element codes for the analysis of a variety of explosive ordnance devices. Both MESA-2D and DYNA3D have been used to evaluate the role of several design parameters on the performance of a satellite separation system bolt cutter. Due to a lack of high strain rate response data for the materials involved, the properties for the bolt cutter and the bolt were selected to achieve agreement between computer simulation and observed characteristics of the recovered test hardware. The calculations provided insight into design parameters such as the cutter blade kinetic energy, the preload on the bolt, the relative position of the anvil, and the anvil shape. Modeling of the cutting process clarifies metallographic observation of both cut and uncut bolts obtained from several tests. Understanding the physical processes involved in bolt cutter operation may suggest certain design modifications that could improve performance margin without increasing environmental shock response levels.

S. Goldstein↗
NASA NTRS1997

Low Speed, 2-D Rotor/Stator Active Noise Control at the Source Demonstration

Wake/blade-row interaction noise produced by the Annular Cascade Facility at Purdue University has been modeled using the LINFLO analysis. Actuator displacements needed for complete cancellation of the propagating acoustic response modes have been determined, along with the associated actuator power requirements. As an alternative, weighted least squares minimization of the total far-field sound power using individual actuators has also been examined. Attempts were made to translate the two-dimensional aerodynamic results into three-dimensional actuator requirements. The results lie near the limit of present actuator technology. In order to investigate the concept of noise control at the source for active rotor/stator noise control at the source, various techniques for embedding miniature actuators into vanes were examined. Numerous miniature speaker arrangements were tested and analyzed to determine their suitability as actuators for a demonstration test in the Annular Cascade Facility at Purdue. The best candidates demonstrated marginal performance. An alternative concept to using vane mounted speakers as control actuators was developed and tested. The concept uses compression drivers which are mounted externally to the stator vanes. Each compression driver is connected via a tube to an air cavity in the stator vane, from which the driver signal radiates into the working section of the experimental rig. The actual locations and dimensions of the actuators were used as input parameters for a LINFLO computational analysis of the actuator displacements required for complete cancellation of tones in the Purdue experimental rig. The actuators were designed and an arrangement determined which is compatible with the Purdue experimental rig and instrumentation. Experimental tests indicate that the actuators are capable of producing equivalent displacements greater than the requirements predicted by the LINFLO analysis. The acoustic output of the actuators was also found to be unaffected by the presence of air flow representative of the Purdue experimental rig. A test of the active noise control at the source concept for rotor/stator active noise control was demonstrated. This 2-D test demonstrated conclusively the simultaneous reduction of two acoustic modes. Reductions of over 10 dB were obtained over a wide operating range.

Simonich, John C.↗
NASA NTRS1998

From the Chemistry Lab to Licensing

This is a story of technology maturation and transfer, and licensing. It traces the history of the recently patented ion- exchange material (IEM) from the accidental discovery that this polymer, a battery separator of marginal performance, picked up copper from distilled water passing through corroded copper tubing in the laboratory, to a point where five organizations and one individual have applied for licenses to manufacture and market it or to use it in a wide variety of applications. This story discusses in detail the problems of converting an immature technology into a mature and eventually commercialized technology, without dedicated resources. Readers will develop an appreciation for how the obstacles to maturation and licensing of the technology were faced and overcome. The lessons learned will be discussed, with the hope of enhancing the technology transfer process.

Savino, Joseph M.↗
NASA NTRS1998

Human Mars Mission: Transportation Assessment

The first Human Mars Mission is being projected to take place during the 2011 and 2013 / 2014 Mars opportunities. Two cargo flights will leave for Mars during the first opportunity, one to Mars orbit and the second to the surface, to prepare the descent transportation, landing site reconnaissance, and ascent vehicle and propellant for the crew arriving during the following opportunity. Each trans-Mars injection (TMI) stack will consist of a payload portion (currently coming in at 60 to 84 metric tonnes) and a TMI propulsion stage (currently coming in at 68-156 mt loaded with propellant) for performing the departure ΔVs for the appropriate Mars trajectories. Three different options are being considered for the system(s) that will comprise the TMI stage for each stack and will perform ΔVs that range from 848 meters/second (m/sec) to 4232 m/sec as required by the trajectory (with gravity losses and various performance margins included). Liquid oxygen (LOx) / liquid hydrogen (LH 2 ) and LOx / liquid methane (LCH 4 ) are the propellant options for other transportation elements utilized for descent, ascent, and trans-Earth injection (TEI) in these Mars architectures. This paper will discuss the current applications of the necessary transportation stages to a human Mars mission and project the implications these various options have on an exploration visit to Mars.

Mars Missions↗
NASA NTRS1999

Technology Maturity Towards Highly Reusable Space Transportation Goals

The National Aeronautics and Space Administration's (NASA) Advanced Space Transportation Program (ASTP) has advanced key propulsion and launch vehicle systems technologies towards enabling the concepts identified by the Highly Reusable Space Transportation (HRST) Study as having significant potential for reducing the cost of access to space. The Marshall Space Flight Center (MSFC) manages the ASTP for the NASA Aero-Space Technology Enterprise. The HRST Study was conducted from 1995 through 1997 to evaluated launch concepts with the potential to reduce launch cost to $100 to $200 per pound of payload to low Earth orbit in the 2016 to 2022 timeframe. The HRST represents a generation of launch vehicles beyond the Lockheed-Martin VentureStar concept with a goal of another factor of ten reduction in launch cost below the next generation Reusable Launch Vehicle. Several concepts were developed and evaluated during the initial HRST studies. At the completion of the concept development phase in 1997, four task forces were formed to integrate the results of the study. These task forces were System Concept Definition, Operations Assessment. Cost Assessment and Technology Assessment. The Operations Assessment task force published its final report in November 1998. The Operations Assessment task force evaluated both single stage to orbit (SSTO) and two-stage to orbit (TSTO) concepts. SSTO concepts included horizontal takeoff and horizontal landing, vertical takeoff and vertical landing and vertical takeoff and horizontal landing. Horizontally launched concepts including launch assist options. SSTO concepts included airbreathing and all rocket as well as combination propulsion systems. The Operations Assessment considered the significance of performance margin, flight rate capability, reliability, launch assist, design optimization and technology development. These studies serve as a guide for the ASTP to prioritize technology development towards future highly reusable launch systems. Although the ASTP supports the development of technology that is focused at a near term fully reusable launch vehicle, the core of the technology development is looking ahead to future generations of launch vehicles that will enable dramatic growth in civil and commercial space enterprise. The primary focus of the paper is to status the key enabling technologies including rocket based combined cycle (RBCC) propulsion, magnetic launch assist, long life, low weight rocket propulsion, integral hot structures. robust thermal protection systems and integrated vehicle health management. The ASTP technology roadmap is leading rapidly towards system demonstration and eventual future X vehicle flight demonstrations.

Lyles, Garry↗
NASA NTRS2000

Focus of NASA's Spaceliner 100 Investment Area

This presentation discuss the goals and objectives of the SL100 Technology Focus. Some of the Technology objectives were to: increase system performance margin; drive down operations costs; drive down manufacturing and production costs; and drive down development test and evaluation costs.

Hueter, Uwe↗